Atlona AT-HDR-M2C-QUAD Guida d'installazione

Marca: Atlona

Modello: AT-HDR-M2C-QUAD

Tipo: Guida d'installazione

Installation Guide

AT-HDR-M2C-QUAD

4K HDR Multichannel Digital to Two-Channel Audio

Converter

AT-HDR-M2C-QUAD

1 x AT-HDR-M2C-QUAD

4 x 3-pin captive screw blocks

1 x Power cable

1 x Wall/table mounting brackets

1 x Installation Guide

Package Contents

The Atlona AT-HDR-M2C-QUAD is an audio converter for extracting and downmixing

multichannel PCM, Dolby, and DTS audio from HDMI. The HDR-M2C-QUAD provides

simultaneous audio conversion for four HDMI sources. Each HDMI input features pass-through

on its associated HDMI output. It also includes unbalanced analog and TOSLINK digital audio

outputs with a down-mixed stereo signal. The HDR-M2C-QUAD is compatible with High Dynamic

Range (HDR) formats and is HDCP 2.2 compliant. It supports 4K/UHD video @ 60 Hz with 4:4:4

chroma sampling, as well as HDMI data rates up to 18 Gbps. This quad HDMI audio conversion

device includes EDID management features as well as audio volume and bass / treble controls

for each converter, all available via Ethernet through the Atlona Management System (AMS), the

web GUI, or a control system. The HDR-M2C-QUAD is ideal for serving surround sound and/or

two-channel audio systems from up to four HDMI sources, while facilitating pass-through to a

matrix switcher.

IMPORTANT: Visit http://www.atlona.com/product/AT-HDR-M2C-QUAD for the latest

rmware updates and User Manual.

Installation Guide

AT-HDR-M2C-QUAD

1 RESET LED Indicator

This button shows the reset status.

2 RESET Button

Press this button to reset the AT-HDR-M2C-QUAD.

3 FW

Connect a mini USB cable from a computer to this port to update the rmware.

4 LAN

Connect an Ethernet cable from this port to a Local Area Network (LAN). This port provides

access to the web GUI.

5 I/O 1 - I/O 4

The AT-HDR-M2C-QUAD provides four sets of audio and video input / output ports:

Rear

Analog Audio

Connect the included 3-pin captive

screw block from this port to a two-

channel audio output device. Refer to

Audio Connector (page 3) for wiring

information.

Digital Audio

Connect an optical cable from this

TOSLINK connector to an AV receiver.

Only two-channel audio output is

supported.

OUT

Connect an HDMI cable from this port to

a display or other sink device. This output

supports multichannel audio.

Connect an HDMI cable from this port to a

source with multichannel audio.

6 Power Button

Press this button to power-on or power-o the AT-HDR-M2C-QUAD.

7 Power receptacle

Connect the included power cable from this receptacle to an available electrical outlet.

Front

Panel Descriptions

AT-HDR-M2C-QUAD

FW LAN

OPTICAL

L R

AUDIO OUT

I/O 4

I/O 2

I/O 3

I/O 1

OPTICAL

L R

AUDIO OUT HDMI

HDMI

OPTICAL

L R

OUT

INOUT

OPTICAL

L R

PWR: 100-240VAC 50/60Hz RESET

AT-HDR-M2C-QUAD

1 3 4 6 75

AT-HDR-M2C-QUAD

FW LAN

OPTICAL

L R

AUDIO OUT

I/O 4 I/O 2

I/O 3 I/O 1

OPTICAL

L R

AUDIO OUT HDMI HDMI

OPTICAL

L R

OUT

INOUT

OPTICAL

L R

PWR: 100-240VAC 50/60Hz RESET

AT-HDR-M2C-QUAD

AUDIO OUT HDMI

Installation Guide

AT-HDR-M2C-QUAD

1. Connect an HD/UHD source to each of the HDMI IN ports on the AT-HDR-M2C-QUAD.

2. Connect an HDMI cable from each HDMI OUT port on the AT-HDR-M2C-QUAD to a display

or other sink device. HDMI OUT ports support multichannel audio.

3. Connect an optical audio cable from each OPTICAL port on the AT-HDR-M2C-QUAD, to

a sound bar or other audio output device. Audio output on this port is limited to two-

channels.

4. Connect the included 3-pin captive screw block from each analog audio output to a set of

powered speakers or other output device. Refer to Audio Connector (page 3) for wiring

information.

5. Connect an Ethernet cable from the LAN port on the AT-HDR-M2C-QUAD, to the Local Area

Network (LAN).

6. Connect the included power cable from the power receptacle on the AT-HDR-M2C-QUAD

to an available electrical outlet.

Installation

Audio Connector

GND

The AT-HDR-M2C-QUAD provides analog audio output of two-channel audio, using the included

3-pin captive screw block.

1. Use wire strippers to remove a portion of the cable jacket.

2. Remove at least 3/16” (5 mm) from the insulation of each wire.

3. Insert the wires into the correct terminal on the captive screw connector, as shown below.

4. Tighten the screws to secure the wires. Do not use high-torque devices as this may

damage the screws and/or connector block.

Installation Guide

AT-HDR-M2C-QUAD

For easy conguration of Atlona devices, AMS 2.0 is available from https://atlona.com/AMS for

free. Two options can be used for installation: The free Linux-based software download or the

easy-to-install server hardware (AT-AMS-HW).

Once AMS has been set up:

1. Open a browser on the same network as AMS 2.0 and go to the IP of AMS 2.0. View the

AMS 2.0 installation instructions on how to nd the IP of the software, if necessary.

2. Enter the login information on the AMS 2.0 web page, then click the Login button.

3. View the AT-HDR-M2C-QUAD manual for routing and conguration.

AMS 2.0

WebGUI

The AT-HDR-M2C-QUAD includes a built-in webGUI, which allows easy management and control

of all features. Follow the instructions below to access the webGUI.

1. Set the IP mode of the AT-HDR-M2C-QUAD. By default, the AT-HDR-M2C-QUAD is set to

DHCP mode.

• Static IP mode: Press and hold the recessed button, with the tip of a pencil or

paper clip, until the PWR indicator blinks twice. The default static IP address is

192.168.1.254.

• DHCP mode: Press and hold the button until the PWR indicator blinks four times.

2. Connect an Ethernet cable from the LAN port on the AT-HDR-M2C-QUAD, to the Local Area

Network (LAN).

3. Use an IP scanner to determine the IP address of the AT-HDR-M2C-QUAD.

4. Launch a web browser and enter the IP address of the unit.

5. The AT-HDR-M2C-QUAD Login page will be displayed.

6. Enter the following information on the Login page.

Password: Atlona

7. Click the Login button.

Installation Guide

AT-HDR-M2C-QUAD

Connection Diagram

Two-Channel Audio

Video + Multichannel Audio

Ethernet

Two-Channel Audio

Video + Multichannel Audio

AT-HDR-M2C-QUAD

Mutli-zone Ampliﬁer

Soundbar

AV Receiver

Blu-ray Player

Media Player

AT-HDR-H2H-44M

Video + Multichannel Audio

LAN

AT-HDR-H2H-44M

1 2 3 4

RS-232 IR IN

HDMI IN LAN FW DC 24V

SRXTX

OUTPUT 1

OUTPUT 2

OUTPUT 3

OUTPUT 4

AT-HDR-H2H-44M

3 4

POWER

FNC

EDID INFO

ENTER

CANCEL

CH1POWER CH2 CH3 CH4

CH5 CH6 CH7 CH8

8-Channel

Professional Amplifer

AT-HDR-M2C-QUAD

SOURCE: DVD

AAX DEC

BNE XOR

media4

Set-Top Box

SET-TOP BOX

224

Installation Guide

AT-HDR-M2C-QUAD

The AT-HDR-M2C-QUAD includes two rack ears, which can be used to install the unit into a rack.

Use the two enclosure screws, on the sides of the unit to attach the rack ears.

1. Using a small Phillips screwdriver, remove the two screws from the left side of the

enclosure.

2. Position one of the rack ears, as shown below, aligning the holes on the side of the

enclosure with one set of holes on the rack ear.

3. Use the screws from Step 1 to attach the rack ear.

4. Repeat Steps 1 through 3 to attach the second rack ear to the opposite side of the unit.

5. Install the assembly into the rack. Secure the unit to the rack using the oval-shaped holes,

on each rack ear.

AT-HDR-M2C-QUAD

Mounting Instructions

Oval-shaped holes

Installation Guide

AT-HDR-M2C-QUAD

Troubleshooting

Problem Solution

PWR indicator is o. • Check that the included power supply is connect to an

active AC electrical outlet.

• Veriify that the power switch, on the rear of the unit, is in

the ON position.

Multichannel audio is not

heard when using the

OPTICAL connector.

• The OPTICAL connector only supports two-channel LPCM

audio. To hear a multichannel audio source, connect an

HDMI cable from one of the HDMI OUT ports on the AT-

HDR-M2C-QUAD to the sink device.

No multichannel audio on

the HDMI output.

• Make sure that the HDMI cable is connected from the

sink device to the HDMI OUT ports on the AT-HDR-M2C-

QUAD.

• Check that the HDMI cable is in good condition or try

another HDMI cable.

• If the source supports multichannel output, check that the

source is congured to output multichannel audio.

No video signal on the

output.

• Verify that an HDMI cable is connected from each source

device to the HDMI IN ports on the AT-HDR-M2C-QUAD.

• Check that the HDMI cable is in good condition or try

another HDMI cable.

Installation Guide

AT-HDR-M2C-QUAD

trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and

online product images may vary from images shown here.

Version 1

atlona.com • 408.962.0515 • 877.536.3976

Atlona AT-HDR-M2C-QUAD Guida d'installazione

Marca: Atlona

Modello: AT-HDR-M2C-QUAD

Tipo: Guida d'installazione

Scarica il pdf

rapporto

in altre lingue

English: Atlona AT-HDR-M2C-QUAD Installation guide

Atlona AT-HDR-M2C-QUAD Guida d'installazione

Atlona AT-HDR-M2C-QUAD Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti