Agria 3600 Manuale del proprietario

6089_01, 6089_2

Engine: EH17

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions!

Operating Instructions No. 998 422GB 11.12

&

Two-Wheel Tractor

3600

Operating Instructions

Translation of the original operating instructions

2 Two-wheel tractor agria 3600

Symbols, Name Plate

Please complete:

Machine Type No.: ........................

Identification No.:

..........................................................

Engine Type: ................................

Engine No.: ..................................

Date of Purchase: ......................

For name plate, refer to p3/fig. A/16.

For engine type and number, refer to

pages 58/fig. E/8.

Please state these data when order-

ing spare parts to avoid wrong deliv-

eries.

Only use original Agria spare

parts!

Specifications, figures and dimen-

sions stated in these instructions are

not binding. No claims can be derived

from them. We reserve the right for

improvements without changing

these instructions.

This delivery comprises:

l

Operating instructions machine

l

Operating instructions engine

l

Two-wheel tractor

– Basic machine

– Steering handle

l

Tool kit

Symbols

è

- Serviceç= contact

your Agria workshop

Warning – Danger

Caution

Important information

Fuel

Engine Start

Engine Stop

Engine oil Engine oil level

Speed control

Air filter Air cooling

Clutch PTO

Wheel drive

Forward

Reverse

Fast Slow

Differential lock

Brake

Park brake

Open (unlocked)

Closed (locked)

Transmission oil

Transmission oil level

Oiling

Greasing point

Lifting point Visual check

Wear protective gloves

Wear safety shoes

Two-wheel tractor agria 3600 3

A

B

Version 2F2R:

rigid hexagonal wheel

shaft

C

Version 3F2R,

differential, steering brake

Designation of Parts

6

1

7 13 9

5 43

6

1

2

3 8 4

7 13 9

5

11 12

10

4 Two-wheel tractor agria 3600

Designation of Parts

Fig. A:

1 Fuel tank

2 Fuel tank cap

3 Tool kit

4 Steering bar

5 Handlebar

6 Locking lever for steering handle side adjustment and swivel

7 Coupler pin

8 Hitch

9 W-clip

10 Locking lever for coupling attachment

11 Reversing lock bolt (safety bolt)

12 Coupling flange with integrated PTO

13 Weight mounting device and engine guard

14 Engine

15 Transmission oil filling opening and dipstick of basic machine

16 Name plate (Identification No.)

(right, in travel direction)

17 Single-wheel brake drum

18 Wheel flange

19 Transmission oil drain plug

Figure B and C

1 Safety shifting lever

2 Hand lever for differential lock

3 Locking lever for steering handle height adjustment

4 Speed control lever

5 Engine shut-off switch

6 Hand lever for engine clutch

7 PTO speed shifter = for rear attachment

(gear shifter) = for front attachment

8 Fast speed shifter

9 Gear shifter = for rear attachment

(PTO speed shifter) = for front attachment

10 Pawl for single-wheel brake (for driving with mounted trailer)

11 Hand lever for single-wheel brake left = for rear attachment

(Hand lever for single-wheel brake right) = for front attachment

12 Hand lever for single-wheel brake right = for rear attachment

(Hand lever for single-wheel brake left) = for front attachment

13 Locking lever for steering handle side adjustment and swivel

Two-wheel tractor agria 3600 5

Index

Amount of Delivery ........................... 2

Designation

of Parts.................................... 3, 58

Assembly Instructions ..........6–8

1. Safety Instructions........ 9 - 15

Due Use ............................................ 9

2. Specifications

Dimensions ..................................... 16

Machine .......................................... 17

Vibration Acceleration Value........... 17

Engine............................................. 18

Noise Levels ................................... 18

Operation on Slopes....................... 18

3. Devices and

Operating Elements

Engine............................................. 19

Safety Circuit .................................. 20

Clutch.............................................. 21

Gearbox .......................................... 22

Single-Wheel Brake........................ 24

Differential Gear.............................. 25

PTO................................................. 25

Reversing Lock ............................... 25

Loading Belt, Fixing Points............. 26

Steering Handle........................ 26, 27

Drive-Wheels ............................ 28, 29

Snow Chains................................... 29

Wheel Fastening Screws................ 29

Front Weights and

Wheel Weights................................ 30

Coupling and

Decoupling Implements.................. 31

4. Commissioning and

Operation

Commissioning the Machine .......... 35

Starting the Engine......................... 37

Switching off the Engine................. 38

Operations ...................................... 39

Danger Zone................................... 40

Driving with Mounted Trailer ........... 41

Safety References, Handling.......... 42

5. Maintenance

Engine........................................ 43-45

Air Filter .......................................... 44

Machine ..................................... 46-47

Gearbox .......................................... 46

Drive-Wheels .................................. 46

Instant adapter device .................... 47

Steering Handle.............................. 47

Brake............................................... 47

Clutch Play...................................... 48

Safety Circuit .................................. 48

Engine Shut-off Switch ................... 48

General Maintenance ..................... 49

Storage ........................................... 50

Recommendations

Lubricants ....................................... 51

Maintenance and Repair ................ 51

Fuel ................................................. 51

Varnishes, Wear Parts ............. 52

6. Troubleshooting .............. 54-55

Diagram: Electric Diagram .... 56

Lubrication Chart................... 56

Inspection and

Maintenance Chart ................... 57

Conformity Declaration........... 59

Fig. A; B; C .................................... 3

Fig. D + E ..................................... 58

1

3

5

6

4

2

6 Two-wheel tractor agria 3600

Œ Unpack the two-wheel tractor,

fit the steering handle into the

steering column:

•Screw out set screw and hex-

agonal nut (lock nut) until steer-

ing handle can fit into steering

column.

ŽFit steering handle into steer-

ing column – lever (A/6) must lock

into toothed ring of steering han-

dle.

•Screw in set screw until you

feel slight resistance – then

loosen set screw a quarter turn

and lock with hexagonal nut.

•Place Bowden cables (hoeing/

tilling attachment) on the left side

(in travel direction) of steering

handle and as depicted on pages

7 and 8.

l

Steering handle must swivel

easily.

‘Assemble shifters. For this pur-

pose, insert shifters for PTO and

gear shifters into joints of shift le-

vers on gearbox and secure with

W-clips

.

Assembly Instructions

Set screw and hexagonal nut

Assembly of shifters

Steering

handle

Steering

column

Tighten with

lock nut

Œ

•

‘

1/4

•

Ž

Toothed ring

A/6

Two-wheel tractor agria 3600 7

Assembly Instructions

Version 2F2R: rigid hexagonal wheel shaft

Drive-wheel 4.00-

8 with wheel

flange

Wheel weights

Drive-wheel 4.00-10

with wheel adapter

flange

Set screw and

hexagonal nut

Arrangement of Bowden cables

l

Mounting drive-wheels:

– 4.00-8: Mount drive-wheels onto wheel

flanges using wheel screws and washers. Slide

wheels onto hexagonal wheel shaft in such a

way that the arrow tread profile points in travel

direction. Insert linch pin in holes of wheel hub

and shaft. Then turn spring band around the

axle.

– 4.00-10: Screw wheel adapter flanges onto

drive-wheels. Mount drive-wheels onto wheel

flanges using wheel screws and washers. Slide

wheels onto hexagonal wheel shaft in such a

way that the arrow tread profile points in travel

direction. Insert linch pin in holes of wheel hub

and shaft. Then turn spring band around the

axle.

Steering handle

Linch pin

8 Two-wheel tractor agria 3600

Assembly Instructions

Version 3F2R,

differential, steering brake

Set screw and

hexagonal nut

l

Mounting drive-wheels:

– 4.00-8: Mount drive-wheels on wheel flanges us-

ing wheel screws and washers. Mount in such a way

that the arrow tread profile points in travel direction.

Drive-wheel 4.00-8

Wheel weights

– 4.00-10: Screw wheel adapter flanges onto drive-wheels. Then mount drive-

wheels onto wheel flanges using wheel screws and washers in such a way

that the arrow tread profile points in travel direction.

l

Assembly of fast speed shifter:

Push shifter upwards through shifter guide ring (I), screw on ball handle (II),

stick shifter onto gearbox shift lever (III) and secure with spring band (IV).

Steering handle

Drive-wheels 4.00-10

with wheel adapter flange

Arrangement of

Bowden cables

I II III IV

Two-wheel tractor agria 3600 9

Before starting the engine, read the op-

erating instructions and note:

Warning

This symbol marks all paragraphs in

these operating instructions which af-

fect your safety. Pass all safety instruc-

tions to other users and operators.

Due Use

The two-wheel tractor is a hand-control-

led automatic single-axle machine which

can power and/or pull various imple-

ments approved by the manufacturer.

Areas of application are for such as turn-

ing over the ground, mowing grass and

meadowland, snow clearance and

sweeping (due use).

Any other type of operation is consid-

ered undue. The manufacturer is not li-

able for any damages resulting from

undue use, for which the risk lies with

the user alone.

When the single-axle tractor/the all-pur-

pose machine is used on public roads,

the local national road traffic rules must

be observed, e.g. reflectors, lights.

The single-axle tractor/The all-purpose

machine is not intended for use with a

trailer on public roads or as as a tractor

unit without implements.

Due use includes compliance with

manufacturer’s instructions on opera-

tion, maintenance and repair.

Any unauthorized changes to the two-

wheel tractor render manufacturer liabil-

ity null and void.

1. Safety Instructions

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The standard accident prevention regu-

lations must be adhered to, as well as

all other generally accepted rules gov-

erning operational safety, occupational

health and road traffic regulations.

For drives on public roads, the current

traffic code applies.

Accordingly, check the two-wheel trac-

tor for road and operational safety each

time you take up operation.

Only persons familiar with the tractor

and instructed on the hazards of opera-

tion are allowed to use, maintain and

repair the tractor.

Teenagers of 16 years or younger may

not operate the two-wheel tractor!

Only work in good light and visibility.

Operator’s clothes should fit tight. Avoid

wearing loose fitting clothes. Wear

safety shoes.

Note the warning and instruction signs

on the tractor for safe operation. Com-

pliance is for your own safety.

When transporting the tractor on vehi-

cles or trailers outside the area to be

cultivated, ensure that the engine is

turned off.

Careful with rotating tools – keep at a

safe distance!

1

10 Two-wheel tractor agria 3600

Beware of coasting tools. Before you

start any maintenance or repair on them,

wait until tools have come to a complete

stop.

Foreign powered parts shear and crush!

Riding on the attachment during opera-

tion is not permitted.

Implements and their weight affect the

driving, steering, braking, and tip-over

characteristics of the tractor. Therefore,

ensure steering and braking functions

are sufficient. Match operating speed to

conditions.

Do not change settings of governor. High

engine speed increases risk of acci-

dents.

Working Area and

Dangerous Area

The user is liable to third parties work-

ing within the tractor’s working range.

Staying in hazardous area is not per-

mitted.

Check the immediate surroundings of

the tractor before you start it. Watch out

for children and animals.

Before you start work, clear the area

from any foreign object. During opera-

tion, always watch out for further objects

and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to enclo-

sures to prevent damage to tools.

Operation and

Safety Devices

Before you start the engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency.

Ensure that all protective devices are

mounted and positioned to provide pro-

tection.

With no implement mounted, make sure

PTO-shaft is covered with the protec-

tive cap.

Starting the engine

Do not start engine in closed rooms. The

carbon monoxide contained in the ex-

haust fume is extremely toxic when in-

haled.

Before you start the engine set all oper-

ating elements to neutral or idling posi-

tion.

For starting the engine, do not step in

front of the two-wheel tractor and the

implement.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion.

Operation

Never leave the operator’s position at

the steering handle while tractor is at

work.

Never adjust the operating handles dur-

ing work – danger!

1. Safety Instructions

1

Two-wheel tractor agria 3600 11

During operation do not leave the op-

erator’s position at the steering handle,

especially not when you turn the ma-

chine.

Riding on the implement during opera-

tion or in transport is not permitted.

If clogging occurs in the implement, turn

off the engine and clean the implement

with an appropriate tool.

In case of damage to the two-wheel trac-

tor or to the implement, immediately turn

off the engine and have it repaired.

If steering causes problems, immedi-

ately bring the two-wheel tractor to a halt

and turn it off. Have the malfunction re-

moved without delay.

To prevent the tractor from sliding on

slopes make sure it is secured by an-

other person using a bar or a rope. This

person must be located at a higher po-

sition than the vehicle at a safe distance

from the attachment at work.

If possible, always work diagonally to

the slope.

End of Operation

Never leave the two-wheel tractor unat-

tended with the engine running.

Before you leave the two-wheel tractor,

turn off the engine. Then close fuel taps.

Secure two-wheel tractor against unau-

thorized use. If tractor is equipped with

ignition key, remove the key. For all other

versions, remove spark plug connector.

Implements

Only mount implements with the engine

and PTO switched off.

Always use appropriate tools and wear

gloves when changing implements and

parts thereof.

For mounting and removing implements

bring support leg into proper position

and ensure stability.

Secure two-wheel tractor and imple-

ments against rolling off (parking brake,

wheel chocks).

Beware of injuries while coupling imple-

ments.

Hitch implements as specified and only

couple at specified points.

Secure two-wheel tractor and implement

against unauthorized use and rolling off

when you leave the machine. If neces-

sary, install transport or security devices

and secure.

Hoeing Attachment

When hoeing and tilling on difficult

ground (stony, hard etc.) the machine

may give sudden jerking movements in

an upward and forward direction and

therefore extra care should be taken

under these conditions.

Adjust protective cover of hoeing attach-

ment so that only those parts of tools

which penetrate the soil are not covered.

When hoeing, make sure hoeing skid is

adjusted properly.

1. Safety Instructions

1

12 Two-wheel tractor agria 3600

Mowing Implement

Handle with care! Sharp blades of the

cutter bar may cause injuries! Remove

protective knife strips only for mowing

and refit immediately after work has fin-

ished.

For transport and storage always mount

the protective knife strips. Secure fin-

ger bars additionally with tension

springs.

Do not transport the removed cutter bar

without protective strips.

When mounting and removing the cut-

ter bar, make sure all blades are pro-

tected by the knife strip.

To exchange the knife and to mount/re-

move the knife head, make sure that you

turn screws away from cutting blades.

For grinding the mowing knives, always

wear safety goggles and gloves.

Trailer

Make sure to not exceed permissible

tongue load of trailer coupling, floating

drawbar or hitch.

When coupling the drawbar, make sure

manoeuvrability at coupling point is suf-

ficient.

Do not exceed gross axle weight rating,

towing capacity and gross weights.

Before driving, check brake function and

rear lighting for proper operation.

Regularly check brake systems closely.

Have adjustments and repairs on the

brake system carried out by a profes-

sional workshop or an authorized brake

service station only.

When driving with mounted trailer, do

not use single-wheel braking.

On tractors equipped with single-wheel

transmission do not engage single-

wheel transmission. Single-wheel trans-

mission must be locked!

For tractors equipped with differential

lock; do not use differential lock when

driving in curves.

Only one passenger may ride on the

trailer, provided a safe passenger seat

is available.

No additional passengers may be car-

ried.

When driving downhill, shift into lower

gears in time. On slopes never de-clutch

to change gears.

Weights

Fit weights properly and at specified

points.

1. Safety Instructions

1

Two-wheel tractor agria 3600 13

Maintenance

Never carry out any maintenance or

cleaning with the engine running.

Before you work on the engine, always

remove spark plug connector (petrol

engine only).

Check regularly and, if necessary, re-

place all protecting devices and tools

subject to wear and tear.

Replace damaged cutting tools.

Always wear safety gloves and use

proper tools when exchanging cutting

tools.

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. steering han-

dle, coupling devices)!

Keep two-wheel tractor and implement

clean to avoid risk of fire.

Check nuts and screws regularly for tight

fit and re-tighten, if necessary.

Ensure that you re-install all safety and

protective devices and adjust them prop-

erly after maintenance and cleaning.

Only use original agria spare parts. All

other commercial spare parts must cor-

respond to quality and technical require-

ments specified by agria.

1. Safety Instructions

Storage

It is not allowed to store the two-wheel

tractor in rooms with open heating.

Never park the two-wheel tractor in

closed rooms with fuel left in tank. Fuel

vapours are hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed rooms.

Extreme danger of intoxication! For the

same reason, also replace damaged

exhaust parts immediately.

Caution with hot engine parts!

The exhaust and other engine parts

become very hot, if the engine runs and

immediately after turning off. Hold for

sufficient distance from hot surfaces and

keep children away from the running

engine.

Be careful when dealing with fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot

engine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine switched off

and cooled down.

Do not spill any fuel, use a proper filling

device (e.g. funnel).

In case of fuel-spillage, pull the two-

wheel tractor away from the spillage

before you start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

For safety reasons the petrol tank and

fuel cap should be replaced regularly.

1

14 Two-wheel tractor agria 3600

Store anti-corrosive agents and stabi-

lizing liquids out of reach of children. If

sickness and vomiting occur, see a doc-

tor. If fuel has contacted eyes, rinse

them thoroughly, avoid inhaling of va-

pours.

Read and observe enclosed instruc-

tions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark for-

mation or flames. If necessary, dispose

of tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil used is of specified qual-

ity. Storage is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

Tyres and

Tyre Air Pressure

When working on tyres, make sure two-

wheel tractor is parked properly and se-

cured against rolling off.

Any repairs are to be carried out by

trained mechanics only and with the

appropriate tools.

Regularly check tyre air pressure. Ex-

cessive pressure may cause bursts.

Use appropriate tyre air pressure for

operation with implements.

Re-tighten fastening screws of drive-

wheels or check tightness when doing

maintenance work.

Electrical System

Persons having a pacemaker may not

touch live parts of the ignition system

when the engine is running.

1. Safety Instructions

1

Two-wheel tractor agria 3600 15

Explanation of

Warning Signs

Before any cleaning, maintenance, and

repair work switch off the engine and

pull spark plug connector.

With engine running, keep at a safe dis-

tance from cutting or hoeing tools.

Do not work without protective covers

mounted. Before starting the engine,

bring covers in proper position.

With engine running, keep at a safe dis-

tance from cutting knife.

1. Safety Instructions

Do not touch moving machinery parts.

Wait until they have come to a complete

stop.

With engine running, keep at a safe dis-

tance from tractor.

Signs

When working with the ma-

chine, wear individual protec-

tive ear plugs.

Wear protective gloves.

Wear safety shoes.

1

16 Two-wheel tractor agria 3600

2. Specifications

Two-Wheel Tractor

Dimensions: (mm)

Dimension Version

2V2R 3V2R

A 605 605

A

1

1170 1170

B

4.00-8 450-730 395-495

4-00-10 480-710 440-550

C 800-1000 800-1000

C

1

760-1010 760-1010

D 1650 1650

D

1

1715 1715

E 790 790

E

1

575 575

F 595 595

F

1

755 755

Tyres:

.................................4.00-8 (field tyre)

......................... or 4.00 -10 (field tyre)

Tyre air pressure...................... 1.2 bar

Track width, version 2F2R: [mm]

4.00-8..................................... 352-632

4.00-10................................... 380-610

To adjust track width slide wheel hub

on hexagonal wheel shaft accordingly

and mount drive-wheels on their inner

or outer side as required.

A S i A S i A S i A S i A S i A S i

495 392 290 395 292 190 550 440 330 520 410 300 490 380 270 440 330 220

Track width version 3F2R: [mm]

Tyre: 4.00-8 Tyre: 4.00-10

2

Two-wheel tractor agria 3600 17

Clutch:........................ Disc dry clutch

Gearbox:

Version 2F2R ....Mechanical gearbox,

2 forward and 2 reverse speeds

Version 3F2R ....Mechanical gearbox,

3 forward and 2 reverse speeds

(3rd gear with rear attachment only)

single-wheel brake on both wheels

differential, lockable

Transmission oil:

Filling quantity approx. ................ 1.5 l

Transmission oil ...SAE 90 - API - GL5

(e.g. BP Energear Hypo)

2. Specifications

PTO:..................................... 1028 rpm

at engine speed of 3600 rpm

gear independent

(integrated in coupling flange)

direction of rotation: right-hand

(clockwise), looking on PTO,

constant in forward and reverse

20 mm tooth profile

Attachment coupling:........ Ø 47 mm

Steering handle: .......height and side

adjustable without tools

swivels 180° for front attachment

Vibration acceleration values:

on handlebar:................ a

hw

< 2.5 m/s

2

in accordance with ISO 5349 at 85% of

rated engine speed with tool at work.

Weights:

Curb Weight: with drive-wheels

Version 2F2R .......................... 61.5 kg

Version 3F2R .......................... 69.5 kg

Permissible total weight........... 150 kg

Permissible tongue load

on coupling point: ...................... 55 kg

Travel Speeds [km/h]

Rear

attachment

Front

attachment

Tyre Gear Gear

1 2 1 2

4.00-8 forward 1.3 2.4 2.1 3.9

4.00-8 reverse 2.1 3.9 1.3 2.4

4.00-10 forward 1.5 2.7 2.5 4.1

4.00-10 reverse 2.5 4.1 1.5 2.7

Travel Speeds [km/h]

Rear

attachment

Front

attachment

Tyre Gear Gear

1 2 3 1 2

4.00-8 forward 1.3 2.4 7.0 2.1 3.9

4.00-8 reverse 2.1 3.9 1.3 2.4

4.00-10 forward 1.5 2.7 7.8 2.5 4.1

4.00-10 reverse 2.5 4.1 1.5 2.7

2

18 Two-wheel tractor agria 3600

Engine

Manufacturer:...........................Robin

Type:..................................... EH 17 D

Version:.......... Fan-cooled 1-cylinder-

4-stroke engine (petrol)

Bore:........................................ 67 mm

Stroke:..................................... 49 mm

Cubic capacity: ................... 172 ccm

Output: .................................... 4.0 kW

at 3600 rpm

Torque: .............................max 11 Nm

at 2600 rpm

Spark plug: ................ Bosch WR7AC

NGK BR 6 HS

Electrode gap: ................. 0.6–0.7 mm

Ingnition system:

Contactless electronic magnet ignition,

ignition point is pre-set, radio remote

screened according to VDE 0879

Valve lash (engine cold)

Intake: .......................... 0.08–0.11 mm

Outlet: .......................... 0.08–0.11 mm

Starter: ..........................Recoil starter

Fuel tank capacity: ....... approx. 3.6 l

Fuel: ...................... Commercial petrol

octane number min. 90 RON

(refer to fuel recommendations)

Air filter: ..................Dry filter element

with foamed preliminary filter

Carburetor: .... Horizontal throttle float

carburetor

Mix Control Screw:

Base setting approx. 1 3/8 revs. open

Main jet: ........................................ 105

Idle jet: ............................................ 50

Rated speed: ......................3600 rpm

Top no-load speed:............3800 rpm

Idling speed:.......................1200 rpm

Engine oil:

Filling quantity............... approx. 0.65 l

Multi-grade oil SAE 10W-40 API-SC or

higher quality

Operability on Slopes:

Engine is suited for use on slopes (with

oil level at “max” = upper level mark)

Continuous operation

possible.. up to 45° inclination (100%)

Noise level:

Noise level

at operator’s ear...................... 80 dBA

(in accordance with EN 709)

2. Specifications

2

Two-wheel tractor agria 3600 19

The two-wheel tractor agria 3600

is a basic motorised unit and is

always used with an implement.

Therefore it is most suitable for

normal use in landscape gar-

dening and in agriculture and for-

estry work for such as turning

over the ground, mowing grass

and meadowland, snow clearing

and sweeping.

When the single-axle tractor/the

all-purpose machine is used on

public roads, the local national

road traffic rules must be ob-

served, e.g. reflectors, lights.

Available attachments:

l

Rear attachments for, e.g.:

– hoeing and tilling

– draft implements for soil

cultiva-

tion

– two-wheel trailer

– gravel and salt spreading

l

Front attachments for, e.g.:

– mowing

– sweeping

– snow clearing and tilling

– gravel and salt spreading.

For a choice of further attach-

ments refer to our price-list.

Engine

l

The four-stroke petrol engine runs on com-

mercial petrol (refer to fuel recommendations

p51).

Ignition System

The engine is equipped with a contactless igni-

tion system. We recommend to have necessary

check-ups done by an expert only.

During the first 20 operating hours (break-in

period) do not use engine to maximum power.

Even after break-in period never use engine

at higher speed than necessary for the work in

hand.

I

High engine speed is harm-

ful to any engine and con-

siderably affects its durability. This applies

especially for no load operation. Any

overspeed (have the engine roar) can result

in immediate damage.

Cooling System

Cooling system is fan-cooled. Therefore keep

screen at recoil starter and cooling ribs of cyl-

inder clean and free from sucked-in plant trash.

Idling Speed

Always ensure that idling-speed is adjusted

correcty. At low speeds and with the speed con-

trol lever set to idle, the engine is supposed to

run smoothly and without run-out.

Air Filter

The air filter purifies the air intake. A clogged

filter reduces engine output.

3. Devices and Operating Elements

3

20 Two-wheel tractor agria 3600

Speed Control Lever

The speed control lever (B/4 and C/4) on the steering

handle is for stepless control of engine speed from min

= IDLING to max = FULL THROTTLE to fit require-

ments.

Engine Shut-off Switch

The machine is equipped with an electric shut-off switch

(B/5; C/5). On pressing the switch, the ignition is turned

off (engine is shut off).

Position „O“ = Engine off

Position „I“ = Operation

I

The engine shut-off switch also serves as an

emergency shut-off. Set the switch to “O” for

fast shut-off.

Safety circuit

The machine is equipped with a safety lever.

ŒStop position: When safety lever (A/24) is not oper-

ated the clutch is disengaged but the engine continues to

run.

•Operating position: for operation press the safety

lever (A/24) down, actuating the connection between

the engine and the gearbox.

l

The safety circuit must be operated in two steps:

1. Press the locking catch (unlatching)

2. Push safety lever downwards.

If the drive to the wheels and the cultivator is

switched on, the wheels and the cultivating tools

begin to turn immediately, therefore do not press

the safety lever down until the drives are set at 0

and the clutch lever is in the disengaged position.

W

Do not tie down safety circuit lever.

I

The safety lever also serves as an emergency

shut-off. In an emergency release it. The lever

automatically goes to STOP position.

3. Devices and Operating Elements

3

B/5; C/5

1.

2.

I

B/1; C/1

•

Œ

max.

min.

B/4; C/4

La pagina sta caricando ...

Agria 3600 Manuale del proprietario

Agria 3600 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti