Agria 8000-53 Manuale del proprietario

Marca: Agria

Modello: 8000-53

Categoria: Tosa erba

Tipo: Manuale del proprietario

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No.

998 793-A 11.11

Brush CutterBrush Cutter

Brush Cutter

80008000

8000

- 8000 511 53 cm

Operating InstructionsOperating Instructions

Operating Instructions

Translation of the original operating instructionsTranslation of the original operating instructions

Translation of the original operating instructions

2 agria Brush Cutter 8000

Symbols, Name Plate

Please complete:

Machine Type No.: ......................

ID/Machine No.:

....................................................

Engine Type: .............................

Engine No.: ..................................

Date of Purchase: ........................

For name plate, refer to p3/fig. A/17.

For Engine type and number, refer to

p38/fig. B/7.

Please state these data when order-

ing spare parts to avoid wrong deliv-

eries.

Only use original agria spare parts!

Specifications, figures and dimen-

sions stated in these instructions are

not binding. No claims can be derived

from them. We reserve the right for

improvements without changing these

instructions.

This delivery comprises:

Operating instructions

Engine operating instructions

Rotary mower

Symbols

Warning – Danger

Important information

Choke

Fuel

Oil

Engine Start

Motordrehzahl

Engine Stop

Air filter

Visual check

Mowing drive

Wheel drive

Fast

Slow

Open (unlocked)

Closed (locked)

see engine operating

instructions

è - Serviceç

= contact Your agria workshop

Please observe that only those activities of the engine are described here

which are required for operating the brush cutter. All other information on the

engine may be taken from the enclosed engine operating instructions!

agria Brush Cutter 8000 3

Designation of Parts

8000 511

Fig. A

1 Clutch lever for mowing drive (safety fitting)

2 Clutch lever for wheel drive (safety fitting)

3 Shifting yoke

4 Speed control lever

5 Handlebar

6 Adjusting screw

7 Locking screw

8 Engine

9 Front cover (protective cover)

10 Guide (protective cover)

11 Front protection liner (protective cover)

12 Cutter blade

13 Runner

14 Mower housing

15 Wheel

16 Rear protection liner

(protective cover)

17 Name plate/ID No.

4 agria Brush Cutter 8000

Lubricants and

Anti-Corrosive

Agents:

Use the lubricants

specified for engine and

gearbox (see “Specifica-

tions”).

We recommend using

Bio-lubricating oil or

Bio-lubricating grease

for “open” lubrication

points or nipples (as

specified in the operating

instructions).

We recommend using

Bio-slushing oil to

preserve machines and

attachments (do not

apply on painted covers).

You can brush or spray

the oil.

Anti-corrosive agents are

environmentally friendly

and degrade fast.

Using ecologically safe

Bio-lubricants and Bio-

anti-corrosives, you con-

tribute to environmental

protection and to the

wellbeing of humans,

animals and plants.

Fuel

This engine runs smooth-

ly on commercial un-

leaded regular and su-

pergrade petrol (inclu-

ding E10).

Do not add oil to petrol.

If, for environmental rea-

sons, you use unleaded

petrol, make sure the fuel

is drained completely

when shutting down the

engine for more than 30

days. This is to prevent re-

sin residue from depo-

siting in the carburetor,

fuel filter, and tank. Or add

a fuel stabilizer to the fuel.

For further instructions re-

fer to “Engine Preservati-

on”.

Recommendations

Maintenance and

Repair:

The trained mechanics of

your agria workshop ex-

pertly carry out any

maintenance and repair

work.

You should only carry out

major maintenance work

and repairs on your own,

if you have the proper tools

and knowledge of machi-

nes and internal combusti-

on engines.

Do not hammer against

the flywheel with a hard

object or metal tools as it

might crack and shatter in

operation, causing injuries

and damage. Only use

suitable tools to pull off the

flywheel.

agria Brush Cutter 8000 5

Index

Amount of Delivery ........................... 2

Symbols, Name Plate ....................... 2

Designation of Parts, Fig. A........... 3

Recommendations............................ 4

Instructions for Unpacking and Assembly .6

1. Safety Instructions ..................... 8

2. Specifications ........................... 13

2.1 Brush Cutter ............................. 13

3. Devices and Operating Elements ...

3.1 Engine....................................... 14

3.2 Speed Control Lever................. 15

3.3 Safety Circuit ............................ 15

3.4Travelling Drive .......................... 16

3.5 Mowing Drive ............................ 16

3.6 Switching to mowing................. 16

3.7 Switching to travelling............... 16

3.8 Shifting Yoke ............................. 16

3.9 Steering Handle ...............................

3.10 Transportation Position ...................

3.11 Cutting height.................................. 18

3.12

Slinging grip ..............................

4. Commissioning and Operation 19

4.1 Commissioning the Machine .... 19

4.2 Starting the Engine................... 20

4.3 Shutting off the Engine ............. 21

4.4 Driving....................................... 22

4.5 Stopping.................................... 22

4.6 Mowing ..................................... 23

4.7 Stopping.................................... 23

4.8 Danger Zone............................. 24

4.9 Mowing on Slopes .................... 25

4.10 Notes for Mowing/Mulching .... 26

5. Maintenance ............................ 27

5.1 Engine..................................... 27

5.2 Cleening the Cooling Screen.. 27

5.3 Cooling System ...................... 27

5.4 Exhaust................................... 27

5.5 Speed Actuating Devices ....... 27

5.6 Gearbox .................................. 28

5.7 Drive-Wheels .......................... 28

5.8 Bowden Cables....................... 28

5.9 Protection Liners..................... 28

5.10 Knife change......................... 29

5.11 Re-Grinding Mowing Knives . 29

5.12 V-Belt Tension for Travelling

Drive.............................................. 30

5.13 Switch for Travelling Drive .... 30

5.14 Switch for Mowing Drive ....... 30

5.15 Changing V-belt .................... 31

5.16 Cutter Brake.......................... 31

5.17 General Maintenance ........... 32

5.17 Cleaning................................ 32

5.18 Disposal ................................ 32

6. Troubleshooting ...................... 34

Varnishes, Wear Parts .................. 36

Inspection and

Maintenance Chart ..................... 37

Designation of Parts, Fig. B ....... 38

Conformity Declaration .............. 39

Note fold-out pages!

Fig. A, Machine .............................. 3

Fig. B, Engine .............................. 38

6 agria Brush Cutter 8000

Instructions for Unpacking and Assembly

Brush cutter

Preparations for

working

Cut open the 4 sides of the

packaging box and fold them

down or pull the machine out

using the grasping points A + B

è page 18

 Set the steering bar (A/5) to

working height

èpage 17

 Guide (A/10)

- protection cover -!

assemble using the screws and

plates shown immediately after

unpacking and place into wor-

king position.

Only operate the ma-

chine if all protective

coverings and safety fittings

have been placed into the

safety position and are in

working order!







A/5

A/10

1 Mower housing

2 Guide

3 Disk 8,4x25x1,6

4 Screw M8x25

5 Plastic disk 8,4x25x5

6 Locking nut M8

7 Securing disk 8

8 Screw M8x12

agria Brush Cutter 8000 7

 Read and note the HONDA engine operating

instructions

 Fill in engine oil

è see operating instructions for HONDA engine

 Check engine oil level

è see operating instructions for HONDA engine

 Fill in fuel

è see operating instructions for HONDA engine

Instructions for Unpacking and Assembly









8 agria Brush Cutter 8000

Before starting the engine, read the op-

erating instructions and note:

Warning

This symbol marks all paragraphs which

affect your safety. Pass all safety instruc-

tions to other users and operators.

Due Use

The brush cutter is constructed solely for

the cutting of grass and similar plants as

well as thin non-wooded scrub in land &

forest management, green spaces, and

other such areas. However it is not

intended for lawn areas in parks!

(due

use).

Any other type of operation is consid-

ered undue. The manufacturer is not li-

able for any damages resulting from

undue use, for which the risk lies with

the user alone.

Due use includes compliance with

manufacturer’s instructions on opera-

tion, maintenance and repair.

Any unauthorized changes to the brush

cutter render manufacturer liability null

and void.

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The standard accident prevention regu-

lations must be adhered to, as well as

all other generally accepted rules gov-

erning operational safety, occupational

health and road traffic regulations.

For drives on public roads, the national

traffic code applies.

Accordingly, check the brush cutter for

road and operational safety each time

you take up operation.

Only persons familiar with the brush

cutter and instructed on the hazards of

operation are allowed to use, maintain

and repair the brush cutter.

Teenagers of 16 years or younger may

not operate the brush cutter!

Only work in good light and visibility.

Operator’s clothes should fit tight. Avoid

wearing loose fitting clothes. Wear solid

shoes.

Note the warning and instruction signs

on the brush cutter for safe operation.

Compliance is for your own safety.

When transporting the brush cutter on

vehicles or trailers outside the area to

be mowed, ensure that the engine is

turned off.

Careful with rotating tools – keep at a

safe distance!

1. Safety Instructions

agria Brush Cutter 8000 9

Beware of coasting tools. Before you

start any maintenance or repair on them,

wait until tools have come to a complete

stop.

Foreign powered parts shear and crush!

Riding on the attachment during opera-

tion is not permitted.

Do not change settings of governor. High

engine speed increases risk of

accidents.

Working Area and Danger

Zone

The user is liable to third parties work-

ing within the brush cutter’s working

range.

Staying in danger zone is not permit-

ted.

Check the immediate surroundings of

the brush cutter before you start it.

Watch out for children and animals.

Before you start work, clear the area

from any foreign object. During opera-

tion, always watch out for further objects

and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to enclo-

sures to prevent damage to tools.

Operation and Safety

Devices

Before you start the engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency.

Ensure that all protective devices are

mounted and positioned to provide

protection.

Starting the engine

Do not start engine in closed rooms. The

carbon monoxide contained in the ex-

haust fume is extremely toxic when in-

haled.

Before you start the engine set all oper-

ating elements to neutral or idling posi-

tion.

For starting the engine, do not step in

front of the brush cutter.

Operation

Never leave the operator’s position at the

steering handle while brush cutter is at

work.

Never adjust the operating handles dur-

ing work – danger!

1. Safety Instructions

10 agria Brush Cutter 8000

During operation the operator must keep

at a distance as defined by the steering

handle, especially when turning the

machine.

Riding on the implement during opera-

tion or in transport is not permitted.

If clogging occurs in the cutting section,

turn off the engine and clean the cutting

section with an appropriate tool.

In case of damage to the brush cutter,

immediately turn off the engine and have

it repaired.

If steering causes problems, immedi-

ately bring the brush cutter to a halt and

turn it off. Have the malfunction removed

without delay.

To prevent the brush cutter from sliding

on slopes, make sure it is secured by

another person using a bar or a rope.

This person must be located at a higher

position than the vehicle and at a safe

distance from the attachment at work.

If possible, always work horizontally on

the slope.

End of Operation

Never leave the brush cutter unattended

with the engine running.

Before you leave the brush cutter, turn

off the engine.

Secure brush cutter against unauthor-

ized use. If brush cutter is equipped with

ignition key, remove the key. For all other

versions, remove spark plug connector.

Mowing Attachment

Handle with care! Sharp blades of the

mowing knives may cause injuries!

To exchange the mowing knife make

sure that you turn screws away from

cutting edges.

For grinding the mowing knives, always

wear safety goggles and gloves.

Maintenance

Never carry out any maintenance or

cleaning with the engine running.

Before you work on the engine, always

remove spark plug connector (petrol

engine only).

Check regularly and, if necessary, re-

place all protecting devices and tools

subject to wear and tear.

Replace damaged cutting tools.

Always wear safety gloves and use

proper tools when exchanging cutting

tools.

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. coupling de-

vices)!

Keep brush cutter clean to avoid risk of

fire.

Check nuts and screws regularly for tight

fit and re-tighten, if necessary.

After maintenance and cleaning, ensure

that you re-install all safety and protec-

tive devices and adjust them properly.

Only use original agria spare parts. All

other commercial spare parts must cor-

respond to quality and technical require-

ments specified by agria.

1. Safety Instructions

agria Brush Cutter 8000 11

Storage

It is not allowed to store the brush cutter

in rooms with open heating.

Never park the brush cutter in closed

rooms with fuel left in tank. Fuel vapours

are hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed

rooms. Extreme danger of intoxication!

For the same reason, also replace

damaged exhaust pipe immediately.

Caution with hot engine parts!

The exhaust and other engine parts

become very hot, if the engine runs and

immediately after turning off. Hold for

sufficient distance from hot surfaces

and keep children away from the

running engine.

Be careful when dealing with fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot

engine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine switched off

and cooled down.

Do not spill any fuel, use a proper filling

device.

In case of fuel spillage, pull the brush

cutter away from the spillage before you

start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Store anti-corrosive agents and stabi-

lizing liquids out of reach of children. If

sickness and vomiting occur, see a doc-

tor. If fuel has contacted eyes, rinse

them thoroughly, avoid inhaling of va-

pours.

Read and observe enclosed instruc-

tions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark for-

mation or flames. If necessary, dispose

of tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil is of specified quality. Stor-

age is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

Electrical System and

Battery

Persons having a pacemaker must not

touch live parts of ignition system when

the engine is running.

1. Safety Instructions

12 agria Brush Cutter 8000

Explanation of

Warning Signs

Attention:

 Carefully read operator's manual befo-

re handling the machine. Observe instruc-

tions and safety rules when operating.

Before any cleaning, maintenance, and

repair work switch off the engine and pull

spark plug connector.

 Before each fuel fill, shut off the en-

gine and wait until it has cooled off. No

open fire! Do not smoke!

 The exhaust fumes contain breath

poisons - keep distance. Never let the

engine run in closed rooms.

 Keep your distance from hot parts

(e.g. engine esp. exhaust). Only touch

them when they have cooled down.

 During operation keep at a safe di-

stance from mowing knives.

 Wait until all machine components

have completely stopped before touching

them.

1. Safety Instructions

 Danger - flying objects; keep safe di-

stance of at least 30 m from the machi-

ne as long as the engine is running.

 Risk of tipping over! Do not drive on

slopes greater than 20° .

 When working with the machine,

wear individual protective ear plugs and

safety goggles.

Check engine oil level at least after

8 operating hours.

Wear solid shoes.

Wear protective gloves.

        

agria Brush Cutter 8000 13

2. Specifications

Brush cutter: Type 8000 511

Working width :.......................................................................................... 53 cm

Engine: 4-stroke petrol ohv engine .................................. Honda GCV190

Max. output: at 3,600 rpm.................................... 4.8 kW (6.5 PS)

Torque:............................................... max. 13.7 Nm at 2,500 rpm

Lowest no-load speed...................................... 1,550 - 1,850 rpm

Top no-load speed ..............................................3,000 ± 100 rpm

Fuel: .......................Conventional petrol; Tank capacity...0.91 l

Fuel consumption ......................................................... 310 g/kWh

Air filter ..............................................................................Dry filter

Spark plug: ............................. NGK BPR6ES; BOSCH WR7DC

Engine oil: ........................................ Filling quantity approx. 0.55 l

SAE 10 W-40, SG, SF or higher quality grade

Mowing Drive:.......................................... V-belt clutch with built-in cutter brake

.............................................cutter blade with mulching operation

Travelling Drive .................................................. Worm gear, with claw coupling

....................................................................... Gearbox oil SAE 90

Travelling speed: ................................................................................... 2.4 km/h

Driving wheels: Tyre ................................................ 3.50-6 AS or 13x5.00-6 AS

Tyre air pressure ............................................................... 0.8 bar

V-belt: Travelling Drive........................................... 10x475Li (ZX 497Lw)

Mowing Drive........................................... A13x1400Li (A1430Lw)

Steering handle: ................................................. height-adjustable without tools

Operability on Slopes: ........................................................................... max. 20°

Noise level at operator’s ear In accordance with EN 11201:......... LpA= 82.3 dB

Sound level in accordance with EN ISO 3744:1995

measured: ............................................................... LWA= 91.2 dB

guaranteed:................................................................ LWA= 92 dB

Vibration value in accordance with ISO 5349, EN836 + A1+ A2: ........... 2.8 m/s

Cutting range: .................................... Grass stalks to thin, non-wooden scrub

Cutting height:................................................................. abt. 50 mm and 75 mm

Weight: .............................................................................................. 70 kg

Dimensions: ....................................................................................l = 1500 mm

.................................................................................... b = 660 mm

.................................................................................... h = 960 mm

.................................................... transportation height = 660 mm

14 agria Brush Cutter 8000

3. Devices and Operating Elements

The brush cutter agria type 8000 is

suited for the cutting of grass and similar

plants as well as

thin non-woody scrub

in land and forest management, green

spaces and other such areas. However it

is unsuitable for lawn areas in parks! (

due

use

3.1 Engine

The four-stroke petrol engine runs on

commercial petrol (refer to fuel recom-

mendations p6).

During the first 20 operating hours

(break-in period) do not use engine to

maximum power.

Even after break-in period never use

engine at higher speed than necessary

for the work in hand.

High engine speed is harm-

ful to any engine and con-

siderably affects its durability. This

applies especially for no load opera-

tion. Any overspeed (have the engine

roar) can result in immediate dam-

age.

Cooling System

The cooling system is fan-cooled. There-

fore keep screen at recoil starter and

cooling fins of cylinder clean and free

from sucked-in plant trash.

Idle running speed

Always ensure that idling-speed is ad-

justed correcty. With the speed control

lever set to idle, the engine is supposed

to run smoothly and without run-out at

low engine speed.

Air Filter

The air filter purifies the air intake. A

clogged filter reduces engine output.

Ignition System

The engine is equipped with a mainte-

nance-free, contactless electronic igni-

tion system.

We recommend to have necessary

check-ups done by an expert only.

Choke

The operation of the choke is built into

the speed control lever.

Close the choke for cold starts.

Open the choke for warm starts

and operation.

Fuel tap

The fuel tap (B/11) is on the

carburetor.

agria Brush Cutter 8000 15

3.2 Speed control lever

(Engine Shut-off Switch)

The speed control lever (A/3) on the steering

handle serves to control engine speed, to set

the CHOKE and to stop the engine. For positions

see fig.

The speed control lever also serves as an

emergency shut- off. In an emergency,

move the lever toposition “STOP” to shut off the

engine fast!

3.3 Safety circuit

The brush cutter is fitted with safety clutch le-

vers for mowing and travelling operation.

Stop position: When the clutch lever is re-

leased (A/1 or A/2) the drive in question is swit-

ched off.

The clutch levers also serves as an

emergency shut- off.

The clutch levers must be let go in dangerous

situations which require quick switching-off, they

then swing automatically to the "STOP" positi-

on! - the mowing and travelling drive will be swit-

ched off.

3.4 Travelling Drive

The travelling drive is transmitted through the

gearbox to the driving wheels.

Switching is carried out using the clutch lever

(A/2) on the steering bar.

The driving wheels are fitted with a ball-bearing

overriding clutch, so that turning when operating

the mower is easier.

3. Devices and Operating Elements

16 agria Brush Cutter 8000

3. Devices and Operating Elements

3.5 Mowing Drive

The mowing mechanism is driven by use of a V-belt gearbox and V-belt clutch.

Switching is made through the clutch lever (A/1) on the steering bar.

The mowing mechanism consists of a cutter blade and is equipped with a cutter

brake -safety fitting-.

The blunt blades can be sharpened and slight bending corrected. Replace badly

damaged or bent knife by a new one.

Only operate the brush cutter if all knives are correctly fitted and

tightened into place and if all protective coverings and safety fittings

have been placed into the safety position and are in working order!

A/2

A/1

A/3

3.6 Switching to Mowing

The mowing drive is switched on by pulling the

clutch lever (A/1) on the steering handle.

The clutch lever is fitted with a locking strap to

prevent unintentional engaging. Before pulling the

clutch lever (A/1) the locking strap must be

pressed down.

The mowing drive is switched off by releasing

the clutch lever (A/1) - safety fitting - and is within

a short time braked by the cutter brake.

3.7 Switching to Travelling

The travelling drive is switched on by pulling the

clutch lever (A/2) on the steering handle.

The travelling drive is switched off by releasing

the clutch lever (A/2) - safety fitting.

3.8 Shifting yoke

Both drives can be switched on together using

the shifting yoke (A/3).

Before switching on press the locking strap on

the clutch lever (A/1) for mowing drive.

On releasing the shifting yoke (A/13) the mowing

and travelling drives will be switched off.

agria Brush Cutter 8000 17

3. Devices and Operating Elements

3.9 Steering Handle

Adjusting the steering:

1 Open the adjusting screw A (A/6) by about 1 turn (in an anti-clockwise direc-

tion)

2 Open the locking screw B (A/7) by about 3 turns (in an anti-clockwise direction)

3 Swing the steering bar (A/5) to the desired height or completely forward into

transportation position and move it across its axis until the positional arrow C

points to the set of holes

4 Tighten the locking screw B, approx. 3 turns in a clockwise direction

5 Tighten adjusting screw A by approx. 1 turn in a clockwise direction.

Transportation

Position

A/5

A/7

A/6

3.10 Transportation Position

Shut off the engine and withdraw

spark plug connector

Wear protective gloves.

The steering (A/4) can be swung into a spa-

ce-saving position for transportation

Steering handle èKap. 3.9

Only operate the brush cutter if the

steering is fixed in the working

position!

A/5

18 agria Brush Cutter 8000

3.10 Cutting height

Shut off the engine and with

draw spark plug connector

Wear protective gloves.

The cutting height is set by adjusting

the two runners (A/13) which are

screwed to the mowing housing.

It is possible to set two cutting heights.

Basic setting: I = approx. 50 mm

higher cutting height:

II = approx. 75 mm

3. Devices and Operating Elements

1 Runner

2 Screw in front

3 Screw in the back

4 Spacer

Adjusting:

Loosen the front screw (2) slightly

Loosen the rear screw (3) and unscrew completely

Swing the runner into the next position and insert the rear screw (3) through

the runner and spacer into the relevant hole in the mowing housing

screw down and tighten the counternut and plate from the inner side of the

mowing housing

Tighten the front screw (2)

carry out the same adjusting steps on the other runner.

Both runners must be set to the same height.

3.11 Slinging grips

The grasping points A and B are in-

tended for lifting and loading of the

machine and for attaching the holding

rope when working on slopes.

Only use fully functional

loading straps!

Never walk or remain under

moving loads. Danger!

agria Brush Cutter 8000 19

4. Commissioning and Operation

4.1 Commissioning the Machine

Please note that durability and operational safety of the engine depend to a large

extent on its breaking-in. Always allow a cold engine to warm up for some minutes

and never run it at full throttle at the beginning.

Please note: for the first 20 hours of operation (break-in period) do not use the

engine at full power.

Make sure you check and maintain air filters regularly and use clean fuel.

Only use branded petrol.

Only use fresh, clean fuel (not older than 3 months) and approved fuel cans to be

purchased in special shops. Rusty sheet metal cans or fuel cans not suited for

petrol are not permitted.

For the first commissioning or after longer periods of no operation, fill fuel tank to

maximum to avoid starting problems.

Be careful when dealing with fuel.

Fuel is easily inflammable and explosive in certain conditions!

Do not refill in closed rooms.

Before each fuel fill, shut off the engine and

wait until it has cooled off.

Never refill close to open fire, inflammable

sparks or hot engine parts.

Do not smoke during filling!

Do not spill any fuel, use a proper filling de-

vice.

Do not cause fuel tank to overflow, but leave a 5

mm margin for the fuel to expand.

Please observe the references of the engine operating instructions!

Note: For reasons of transport, the

machine is not filled with engine oil!

Before you operate the engine the first time,

fill in engine oil

20 agria Brush Cutter 8000

Only operate the machine if all protective coverings and safety fittings

have been placed into the safety position and are in working order!

4. Commissioning and Operation





? ok



? ok













2/3

4.2 Starting the Engine

Do not start engine in closed rooms!

Exhaust fumes contain carbon monoxide

which acts toxic when inhaled.

Keep feet away from coupled attachment.

Protective covers mounted?

 Check engine oil level.

 Mount spark plug connector.

 Air filter clean?

 Fuel quantity in tank sufficient?



Open the fuel tap.



Cold engine:

Move the speed control lever (A/3) to position

“CHOKE”

Warm engine:

Set speed control lever to 1/3 throttle

 Set both clutch levers (A/1 + A/2) to position "0"

 Start engine

from a position outside the hazardous area

 after the start push speed control lever to position

"min"

Caution with hot engine parts!

The exhaust and other engine parts become very

hot, if the engine runs and immediately after turning

off. Hold for sufficient distance from hot surfaces

and keep children away from the running engine.

La pagina sta caricando ...

Agria 8000-53 Manuale del proprietario

Marca: Agria

Modello: 8000-53

Categoria: Tosa erba

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Agria 8000-53 Owner's manual

Agria 8000-53 Manuale del proprietario

Agria 8000-53 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti