Briggs & Stratton 0400 Manuale del proprietario

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No.

998 702-C 01.14

&

Briggs&Stratton engine

Multi-Purpose MachineMulti-Purpose Machine

Multi-Purpose Machine

400E and 400K400E and 400K

400E and 400K

3348, 5117, 3346

Operating InstructionsOperating Instructions

Operating Instructions

Translation of the original operating instructionsTranslation of the original operating instructions

Translation of the original operating instructions

2 agria Multi-Purpose Machine 400E/400K

Symbols, Name Plate

Please complete:

Machine Type No.:.........................

Identification No.:

.........................................................

EngineType:.......................................

Engine No.:....................................

Date of Pur-

chase:...................................

For name plate, refer to p3/fig. A/9 or

p7/fig. C/9.

For engine type and number, refer to

p3/fig. B/6 or p7/D/6.

Please state these data when order-

ing spare parts to avoid wrong deliv-

eries.

Only use original agria spare parts!

Specifications, figures and dimen-

sions stated in these instructions are

not binding. No claims can be derived

from them. We reserve the right for

improvements without changing these

instructions.

Amount of delivery:

l

Operating instructions

l

Grassland mower – basic machine

l

Steering handle with grip screw

l

Tool kit

version 400K additionally:

l

Starter battery with battery acid

Symbols:

Warning – Danger

Important information

Fuel

Choke

Engine

Air filter

Engine oil

Engine oil level

Transmission oil level

Visual check

Mowing drive

Wheel drive

Forward

Reverse

Open (unlocked)

Closed (locked)

PTO

è - Serviceç= contact

Your agria workshop

agria Multi-Purpose Machine 400E/400K 3

Designation of Parts Type 400E

A

B

Version

Briggs & Stratton 5 HP

135 202

Version

Briggs & Stratton Power Built 190

110 412

4 agria Multi-Purpose Machine 400E/400K

Designation of Parts Type 400E

Figure A

1 Pto speed shift lever

2 Linkage for front attachments

3 Transmission oil plug (filling and checking oil level)

4 Linkage for rear attachments

5 Grooves on wheel shaft

6 Wheel shaft

7 Gearbox cover/Transmission oil drain opening

8 Pto/pto guard

9 Name plate (machine identification no.)

10 Handlebar

11 V-belt guard (V-belt clutch)

12 Drive wheel

13 Drive-wheel detent spring

14 Guard

Figure B

1 Air filter

2 Carburetor

3 Fuel tank cap

4 Fuel tank

5 Choke lever

6 Engine type no.

7 Starter handle

8 Cooling air-screen

9 Exhaust with guard

10 Spark plug/spark plug connector

11 Engine oil filler plug and control opening

12 Engine oil drain plug

13 Fuel tap (only version Power Built 190)

agria Multi-Purpose Machine 400E/400K 5

Index

Amount of delivery............................ 2

Designation of Parts ... 3,7,62,66

Instructions for Unpacking and

Assembly .................................. 9

Recommendations

Lubricants, Anti-Corrosive Agents.. 10

Fuel ................................................. 10

Maintenance and Repair ................ 10

1. Safety Instructions........11-15

2. Specifications

Dimensions 400E / 400K ........... 16/18

Multi-purpose machine 400E/400K 16/

18

Noise level ................................. 16/18

Vibration acceleration value ...... 16/18

Engine, Ausf 400E / 400K ......... 17/19

Operation on slopes .................. 17/19

3. Devices and Operating

Elements

Engine............................................. 20

Speed control lever ......................... 21

Safety circuit ................................... 21

Choke, fuel tap................................ 22

Clutch.............................................. 22

Main gearbox ........................... 22 - 25

Drive-wheels ............................ 26 - 30

Pto................................................... 31

Stand .............................................. 31

Steering handle .............................. 32

Battery ............................................ 33

Attachments............................. 34 - 37

Hoeing, ridging ........................ 38 - 40

4. Commissioning and

Operation

Commissioning the machine .......... 41

Starting the engine ......................... 42

Switching off the engine ................. 43

Working........................................... 44

Danger zone ................................... 44

5. Maintenance

Engine 400E / 400K................. 45 / 46

Air filter............................................ 47

Fuel system .................................... 47

Cooling system ............................... 48

Spark plug....................................... 48

Governor ......................................... 48

Exhaust........................................... 48

Speed Control................................. 49

Carburetor settings ......................... 49

Battery (400K) ................................ 49

Machine .......................................... 50

Drive-wheels ................................... 50

Safety circuit ................................... 51

Clutch play ................................ 51- 52

General ........................................... 53

Cleaning.......................................... 53

Storage ........................................... 54

6. Troubleshooting...........56 - 57

Electric Wiring Diagram......... 58

Lubrication chart.................... 58

Varnishes,

Wear Parts .............................. 59

Inspection and

Maintenance Sheet ................ 64

Conformity Declaration ......... 67

Note fold-out pages!

Fig. A and B (400E) ................. 3

Fig. C and D (400K) ................. 7

Fig. E and F (400E) ................ 62

Fig. G and H (400K) ............... 66

3

5

2

1

4

6

6 agria Multi-Purpose Machine 400E/400K

agria Multi-Purpose Machine 400E/400K 7

C

D

Designation of Parts Type 400K

8 agria Multi-Purpose Machine 400E/400K

Figure C

1 Pto speed shift lever

2 Linkage for front attachments

3 Transmission oil plug (filling and checking oil level)

4 Linkage for rear attachments

5 Grooves on wheel shaft

6 Wheel shaft

7 Gearbox cover/Transmission oil drain opening

8 Pto/pto guard

9 Name plate (machine identification no.)

10 Handlebar

11 V-belt guard (V-belt clutch)

12 Drive wheel

13 Drive-wheel detent spring

14 Guard

Figure D

1 Air filter

2 Carburetor

3 Fuel tank cap

4 Fuel tank

5 Choke lever

6 Engine type no.

7 Starter handle

8 Cooling air-screen

9 Exhaust with guard

10 Spark plug/spark plug connector

11 Engine oil filler plug and dip-stick

12 Engine oil drain plug

13 Electric starter

14 Battery

Designation of Parts Type 400K

agria Multi-Purpose Machine 400E/400K 9

Instructions for Unpacking

l

Open the box top.

l

Cut the two rear corners open and fold down

the side.

l

Remove the steering handle attachment bolt

(3 + 4).

l

Pivot the steering handle (2) upwards.

Then attach and tighten the bolt (3 + 4).

l

Attach the drive wheels (see instructions on

page 26).

l

Starting-up

See instructions on page 41).

Version Type 400K additionally:

A standard battery charger with 12V DC and a maxi-

mum charge of 0.6 A should be used for the 12V 6Ah

battery (motorcycle battery).

- The battery is packed and must be filled with the

battery acid supplied and fully loaded before fitting.

l

After unpacking fill the battery with the battery acid

supplied in line with the instructions enclosed with

the battery and then close it up. When filling the tem-

perature of the battery and the acid should be at least

10°C .

l

Place the battery in the battery holder (5) and tighten

down using the tensioning spring (6) (place over the

battery and insert the hook into the hole "A" ) and

ensure that the protective hose (7) is located in the

area of the battery terminals.

l

Connect the battery cable; first connect the posi-

tive terminal (+) to the red cable, then the negative

terminal (-) to the black cable - ensure that the termi-

nal screws are firmly tightened.

- When disassembling first disconnect the positive

terminal (+), then the negative terminal (-) .

- Lightly lubricate the battery terminals and terminal

screws with acid-free grease.

- Fit the protective connecting cap (8) over the posi-

tive terminal.

I

The battery operation and its maintenance and

care must be made in line with the battery

manufacturer's operating instructions on page 33.

1 Hexagon nut (terminal screws)

2 Square nut

3 Battery

4 Battery cable

5 Battery holder

6 Tensioning spring

7 Protective hose

8 Connecting cap

and Assembly

10 agria Multi-Purpose Machine 400E/400K

Lubricants and

Anti-Corrosive Agents:

Use the lubricants specified for engine

and gearbox (see “Specifications”).

We recommend using Bio-lubricating

oil or Bio-lubricating grease for “open”

lubrication points or nipples (as speci-

fied in the operating instructions).

We recommend using Bio-slushing oil

to preserve machines and attachments

(do not apply on painted covers). You

can brush or spray the oil.

Anti-corrosive agents are environmen-

tally friendly and degrade fast.

Using ecologically safe Bio-lubricants

and Bio-anti-corrosives, you contribute

to environmental protection and to the

wellbeing of humans, animals and

plants.

Fuel:

This engine runs smoothly on conven-

tional unleaded regular and

supergrade petrol as well as on leaded

supergrade petrol.

Do not add oil to petrol.

If, for environmental reasons, you use

unleaded petrol, make sure the fuel is

drained completely when shutting down

the engine for more than 30 days. This

is to prevent resin residue from deposit-

ing in the caburetor, fuel filter, and tank.

Or add a fuel stabilizer to the fuel.

For further instructions see “Engine

Preservation”.

Maintenance and Repair:

The trained mechanics of your agria

workshop expertly carry out any main-

tenance and repair work.

You should only carry out major main-

tenance work and repairs on your own,

if you have the proper tools and knowl-

edge of machines and internal combus-

tion engines.

Do not hammer against the flywheel with

a hard object or metal tools as it might

crack and shatter in operation, causing

injuries and damage. Only use suitable

tools to pull off the flywheel.

Recommendations

agria Multi-Purpose Machine 400E/400K 11

1. Safety Instructions

Before starting the engine, read the op-

erating instructions and note:

Warning

This symbol marks all paragraphs in

these operating instructions which affect

your safety. Pass all safety instructions

on to other users and operators.

Due Use

The multi-purpose machine is a hand-

controlled automatic single-axle ma-

chine which can power and/or pull vari-

ous implements approved by the manu-

facturer. Areas of application are for such

as turning over the ground, mowing

grass and meadowland, snow clearance

and sweeping (due use).

Any other type of operation is consid-

ered undue. The manufacturer is not li-

able for any damages resulting from

undue use, for which the risk lies with

the user alone.

When the multi-purpose machine is

used on public roads, the local national

road traffic rules must be observed, e.g.

reflectors, lights.

The multi-purpose machine is not in-

tended for use with a trailer on public

roads or as as a tractor unit without im-

plements.

Due use includes compliance with

manufacturer’s instructions on opera-

tion, maintenance and repair.

Any unauthorized changes to the ma-

chine render manufacturer liability null

and void.

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The respective national accident preven-

tion regulations have to be adhered to,

as well as all other generally accepted

rules governing operational safety, oc-

cupational health and road traffic regu-

lations.

When driving on public roads, you have

to observe the current traffic code.

Accordingly, check the machine for road

and operational safety each time you

take up operation.

Only persons familiar with the tractor and

instructed on the hazards of operation

are allowed to use, maintain and repair

the tractor.

Teenagers younger than 16 years are

not allowed to operate the machine!

Only work in good light and visibility.

Operator’s clothes should fit tight. Avoid

wearing loose fitting clothes. Wear solid

shoes.

Note the warning and instruction signs

on the tractor for safe operation. Com-

ply for your own safety.

When transporting the tractor on vehi-

cles or trailers outside the area to be

cultivated, ensure that the engine is

turned off.

Careful with rotating tools - keep at a

safe distance!

Foreign powered parts shear and crush!

Riding on the attachment during opera-

tion is not permitted.

1

12 agria Multi-Purpose Machine 400E/400K

1. Safety Instructions

Mounted or trailed attachments affect

the tractor’s driving, steering, braking,

and tipping characteristics. Therefore,

ensure that steering and braking func-

tions are sufficient. Match operating

speed to conditions.

Do not change settings of governor. High

engine speed increases risk of acci-

dents.

Working Area and

Dangerous Area

The user is liable to third parties work-

ing within the tractor’s working range.

Staying in hazardous area is not per-

mitted.

Check the immediate surroundings of

the tractor before you start it. Watch out

for children and animals.

Before you start work, clear the area

from any foreign object. During opera-

tion, always watch out for further objects

and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to enclo-

sures to prevent damage to tools.

Operation and

Safety Devices

Before you start the engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency.

Ensure that all guards in place.

With no attachment mounted, make

sure PTO-shaft is covered with the pro-

tective cap.

Starting the engine

Do not start the engine in closed rooms.

The carbon monoxide contained in the

exhaust fume is extremely toxic when

inhaled.

Before you start the engine set all con-

trols to neutral or idling position.

When starting the engine, do not step

in front of the machine and the attach-

ment.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion.

Operation

Never leave the operator’s position at the

steering handle while tractor is at work.

Never adjust the handles during work -

danger!

For any operation do not leave the op-

erator’s position as defined by the steer-

ing handle, especially not when you turn

the machine.

Riding on the attachment during opera-

tion or in transport is not permitted.

If blockages occur in the attachment,

turn off the engine and clean the attach-

ment with an appropriate tool.

In case of damage to the multi-purpose

machine or to the attachment, immedi-

ately turn off the engine and have it re-

paired.

If steering causes problems, immedi-

ately bring the machine to a halt and

turn it off.

Have the malfunction removed without

delay.

To prevent the machine from sliding on

1

agria Multi-Purpose Machine 400E/400K 13

1. Safety Instructions

slopes make sure it is secured by an-

other person using a bar or a rope. This

person must be located at a higher po-

sition than the vehicle at a safe distance

from the attachment at work.

If possible, always work horizontally to

the slope.

End of Operation

Never leave the multi-purpose machine

unattended with the engine running.

Before you leave the machine, turn off

the engine. Then close fuel taps.

Secure the machine against unauthor-

ized use. If tractor is equipped with an

ignition key, remove the key. For all other

versions, remove the spark plug connec-

tor to secure the tractor.

Attachments

Only mount attachments with the engine

and PTO switched off.

Always use appropriate tools and wear

gloves when changing attachments and

parts thereof.

To fit and remove attachments, bring the

support leg into proper position and en-

sure stability.

Secure the machine and attachments

against rolling off (parking brake, wheel

chocks).

Beware of injuries while coupling attach-

ments.

Couple the attachments as specified

and only couple at specified points.

Secure the machine and attachment

against unauthorized use and rolling off

when you leave the machine. If neces-

sary, install transport or safety devices

to provide protection.

Hoeing Attachment

Adjust the guards in such a way that only

the sets of blades penetrating the soil

are not covered.

When hoeing, make sure the depth bar

is adjusted properly.

Mowing Attachment

Handle with care! Sharp blades of the

cutter bar may cause injuries when han-

dled improperly! Remove protective

knife strips only for mowing and refit

immediately after work has finished.

For transport and storage always fit the

protective knife strips. Secure finger bars

additionally with tension springs.

Do not transport the removed cutter bar

without protective strips.

When fitting/removing the cutter bar,

make sure all blades are protected by

the knife strip.

To exchange the knife and to fit/remove

the knife driver, make sure that you turn

screws and bolts away from the cutting

blades to remove them.

To grind the mowing knives, always wear

safety goggles and gloves.

Weights

Always fit weights properly and at speci-

fied points.

1

14 agria Multi-Purpose Machine 400E/400K

1. Safety Instructions

Maintenance

Never carry out any maintenance or

cleaning while the engine is running.

Before you work on the engine, always

remove spark plug connector (petrol

engine only).

Check regularly and, if necessary, re-

place all guards and tools subject to

wear and tear.

Replace damaged cutting tools.

Always wear safety gloves and use

proper tools when exchanging cutting

tools.

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. coupling de-

vices)!

Keep the machine and the attachment

clean to avoid risk of fire.

Check nuts and bolts regularly for tight

fit and re-tighten, if necessary.

Ensure that you re-install all safety and

guards and adjust them properly after

maintenance and cleaning.

Only use original agria spare parts. All

other conventional spare parts must

correspond to quality and technical re-

quirements specified by agria.

Storage

It is not allowed to store the machine in

rooms with open heating.

Never park the machine in closed rooms

with fuel left in tank. Fuel vapours are

hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed rooms.

Extreme danger of intoxication! For the

same reason, also replace damaged

exhaust pipes immediately.

Be careful when dealing with fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot

engine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine switched off

and cooled down.

Do not spill any fuel, use a proper filling

device.

In case of fuel-spillage, pull the machine

away from the spillage before you start

the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Store anti-corrosive agents and stabi-

lizing liquids out of reach of children. If

sickness and vomiting occur, see a doc-

tor. If fuel has contacted eyes, rinse

them thoroughly, avoid inhaling of va-

pours.

Read and observe enclosed instruc-

tions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark forma-

tion or flames. If necessary, dispose of

tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil used is of specified qual-

ity. Storage is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

1

agria Multi-Purpose Machine 400E/400K 15

1. Safety Instructions

Tyres and Tyre Pressure

When working on the tyres, make sure

the machine is parked properly and se-

cured against rolling off.

Any repairs are to be carried out by

trained mechanics only and with the

appropriate tools.

Regularly check air pressure in the tyres.

Excessive pressure may cause bursts.

When adding weight, make sure the tyre

pressure is correct.

Re-tighten bolts of drive-wheels or check

tightness when doing maintenance

work.

Electrical System and Battery

When working on the electrical system,

make sure the battery is disconnected

(negative terminal) (for tractors

equipped with battery).

Make sure to connect the battery prop-

erly - first connect the positive terminal

and then negative terminal. Disconnect

in reverse order.

Be careful with battery gases- explosive!

Avoid spark discharge and open flames

near batteries.

Remove plastic cover (if equipped) to

recharge battery and to prevent highly

explosive gases from building up.

Careful when handling battery acid!

Only use specified circuit breakers. If the

circuit breakers are to strong, they will

destroy the electrical system - danger

of fire.

Always cover positive terminal with the

specified cover or terminal cap.

Persons having a pacemaker may not

touch live parts of the ignition system

when the engine is running.

Explanation of

Warning Signs

Before any cleaning,

maintenance, and re-

pair work switch off

the engine and pull

spark plug connector.

With the engine run-

ning, keep at a safe

distance from cutting

or sets of blades.

Do not work without

guards in place. Be-

fore starting the en-

gine, bring guards in

proper position.

With the engine run-

ning, keep at a safe

distance from knife.

Do not touch moving

machinery parts.

Wait until they have

come to a complete

stop.

With the engine run-

ning, keep at a safe

distance.

Only drive the attach-

ment at speed “I”.

Signs

When working with the machine,

wear individual protective ear

plugs.

Wear protective gloves.

Wear solid shoes.

1

16 agria Multi-Purpose Machine 400E/400K

Dimensions:

a ........................................ 100 mm

b ........................................ 630 mm

c......................................... 160 mm

d ........................................ 380 mm

e ........................................ 700 mm

h .............................. 860–1080 mm

l........................................ 1200 mm

A .............. (13x5.00 - 6) 525 mm

A ..................... (3.50 - 6) 440 mm

A (Twin tyres 3.50 - 6) ..... 857 mm

A ..................... (4.00 - 8) 640 mm

A Sets of hoe blades. 450–650 mm

2. Specifications Type 400E

Multi-purpose machine 400E

Clutch: .............................V-belt clutch

with idler pulleys

between engine and gearbox

Friction clutch for reverse speed

Only use original agria V-belts!

(List of wear parts p59)

Gearbox: ................... Worm gear with

overrunning clutch on drive-wheels

Transmission oil SAE 90-API GL5

Filling quantity approx. 0.5 l

Speeds: ...................2 forward speeds

(moving V-belt to another pulley)

1 reverse speed (friction wheel)

see table below

Steering handle:...vibration damping,

height-adjustable,

side-adjustable without tools

Weight: ......................... Approx. 44 kg

Noise level:

In accordance with DIN EN 709 and

DIN EN 1553

Emission noise level ............... 83 dBA

(at operator’s ear)

Vibration acceleration value:

on handlebar:................ a

hw

< 2.5 m/s

2

in accordance with DIN EN 709 and

DIN EN 1033 at 85% of rated engine

speed with tool at work.

Tyres: (Accessory) .............................

................ 13x5.00-6 (Grassland tyre)

....... 3.50 - 6 und 4.00 - 8 (Field tyre)

Tyre pressure: ........................ 1.0 bar

2

Speed Revolutions [rpm] Ground speed [km/h]

Wheel shaft

Pto Tyres

i

tot

n

dw

n

pto

13x5.00-6 3.50-6 4.00-8

I 67.5 55 1650 3.2 3.6 4.4

II 42.7 110 3310 6.7 7.3 8.9

R 61.7 58 1740 3.4 3.8 4.7

agria Multi-Purpose Machine 400E/400K 17

Manufacturer: .........Briggs & Stratton

................................... Power Built 190

Type: .............................110 412-0173

Version: ..... Fan-air-cooled 1-cylinder-

4-stroke engine (petrol)

Cubic capacity: ................... 190 ccm

Output: ............... 4.0 kW at 3600 rpm

Torque max.

.......................... 11.2 Nm at 2600 rpm

Spark plug:: ....... Champion QC12YC

Spark plug gap: 0.75 mm

Ignition system: ............. Contactless

electronic magnet ignition,

ignition point is pre-set, radio remote

screened according to VDE 0879

Starter: ..........................Recoil starter

Fuel tank capacity: .................... 2.8 l

Fuel:..................... Conventional petrol

octane number min. 85 RON

see fuel recommendations

Air filter: .................. Dry filter element

Top no-load speed: ............3800 rpm

Idling speed:....................... 1750 rpm

Engine oil:

Filling quantity.................. approx. 0.6 l

Multi-grade oil SAE 10 W-40 API-SC,

SF or higher

Operability on Slopes:

As long as the operator is able to walk

and drive the power mower on slopes

without problems, the engine perform-

ance is satisfactory (engine oil level at

“max” = upper filling mark).

2. Specifications Type 400E

Engine (pay attention to model type)

Manufacturer: .........Briggs & Stratton

.................................................... 5 HP

Type: ............................135 202 -0271

Version: ..... Fan-air-cooled 1-cylinder-

4-stroke engine (petrol)

Cubic capacity: ................... 205 ccm

Output: ............... 3.2 kW at 3600 rpm

Torque max. ..... 10.0 Nm at 3000 rpm

Spark plug: ....... Champion RJ 19 LM

Spark plug gap 0.75 mm

Ignition system: ............. Contactless

electronic magnet ignition,

ignition point is pre-set, radio remote

screened according to VDE 0879

Valve lash (engine cold)

Intake: .......................... 0.13–0.18 mm

Outlet: .......................... 0.23–0.28 mm

Starter: ..........................Recoil starter

Fuel tank capacity: ...................... 3 l

Fuel:..................... Conventional petrol

octane number min. 85 RON

see fuel recommendations

Air filter: .................. Dry filter element

with foamed preliminary filter

Carburetor: ............................ Updraft

Needle valve screw: .. in basic setting

1 1/2 turns open

Rated speed: ......................3600 rpm

Top no-load speed: ............3800 rpm

Idling speed:.......................1750 rpm

Engine oil:

Filling quantity..................approx. 0.6 l

Multi-grade oil SAE 10 W-40 API-SC,

SF or higher

2

18 agria Multi-Purpose Machine 400E/400K

2. Specifications Type 400K

Tyres: (Accessory) .............................

................ 13x5.00-6 (Grassland tyre)

....... 3.50 - 6 und 4.00 - 8 (Field tyre)

Tyre pressure: ........................ 1.0 bar

Multi-purpose machine 400K

Dimensions

a ........................................ 100 mm

b ........................................ 630 mm

c......................................... 160 mm

d ........................................ 380 mm

e ........................................ 700 mm

h .............................. 860–1080 mm

l........................................ 1200 mm

A .............. (13x5.00 - 6) 525 mm

A ..................... (3.50 - 6) 440 mm

A (Twin tyres 3.50 - 6) ..... 857 mm

A ..................... (4.00 - 8) 640 mm

A Sets of hoe blades. 450–650 mm

2

Clutch: .............................V-belt clutch

with idler pulleys

between engine and gearbox

Friction clutch for reverse speed

Only use original agria V-belts!

(List of wear parts p59)

Gearbox: ................... Worm gear with

overrunning clutch on drive-wheels

Transmission oil SAE 90-API GL5

Filling quantity approx. 0.5 l

Speeds: ...................3 forward speeds

(moving V-belt to another pulley)

1 reverse speed (friction wheel)

see table below

Steering handle:...vibration damping,

height-adjustable,

side-adjustable without tools

Weight: ......................... Approx. 50 kg

Noise level:

In accordance with DIN EN 709 and

DIN EN 1553

Emission noise level ............... 83 dBA

(at operator’s ear)

Vibration acceleration value:

on handlebar:............... a

hwy

< 2.5 m/s

2

in accordance with DIN EN 709 and

DIN EN 1033 at 85% of rated engine

speed with tool at work.

Speed Revolutions [rpm] Ground speed [km/h]

Wheel shaft

Pto Tyres

i

tot

n

dw

n

pto

13x5.00-6 3.50-6 4.00-8

I 67.5 55 1650 3.2 3.6 4.4

II 42.7 85 2550 5.0 5.6 6.9

III 28.1 125 3750 7.3 8.3 10.1

R 61.7 58 1740 3.4 3.8 4.7

agria Multi-Purpose Machine 400E/400K 19

Fuel tank capacity: ...........approx. 3 l

Fuel:..................... Conventional petrol

octane number min. 85 RON

see fuel recommendations

Air filter: .................. Dry filter element

with foamed preliminary filter

Carburetor: ............................ Updraft

Needle valve screw: .. in basic setting

1 1/2 turns open

Rated speed: ...................... 3600 rpm

Top no-load speed: ............3800 rpm

Idling speed:....................... 1750 rpm

Generator:....................... 12 V / 1.2 A

Battery: ........ Starter battery 12V 6Ah

Engine oil:

Filling quantity.................. approx. 0.6 l

Multi-grade oil SAE 10 W-40 API-SC,

SF or higher

Operability on Slopes:

As long as the operator is able to walk

and drive the power mower on slopes

without problems, the engine perform-

ance is satisfactory (engine oil level at

“max” = upper filling mark).

2. Specifications Type 400K

Engine

Manufacturer: .........Briggs & Stratton

Type: ............................133 237 -0136

Version: ..... Fan-air-cooled 1-cylinder-

4-stroke engine (petrol)

Bore: ........................................ 65 mm

Stroke:..................................... 62 mm

Cubic capacity: ................... 205 ccm

Output: ............... 3.2 kW at 3600 rpm

Torque max. ..... 10.0 Nm at 3000 rpm

Spark plug: ....... Champion RJ 19 LM

Spark plug gap 0.75 mm

Ignition system: ............. Contactless

electronic magnet ignition,

ignition point is pre-set, radio remote

screened according to VDE 0879

Valve lash (engine cold)

Intake: .......................... 0.13–0.18 mm

Outlet: .......................... 0.23–0.28 mm

Starter: ................Electric starter 12 V

Recoil starter (manual starter)

2

20 agria Multi-Purpose Machine 400E/400K

3. Devices and Operating Elements

The agria multi-purpose machine type

400 is a basic power machine and is

always operated with an attachment

mounted. Therefore, the machine is

suited for agricultural and forestal op-

erations, horticulture and park mainte-

nance as well as for ground clearing and

winter service.

Available attachments are:

l

hoeing and tilling

l

mowing

l

turf and grounds care

l

ploughing

l

sweeping

l

gravel and salt spreading

l

snow dozing and rotory snow

cleaning

l

transporting

Engine

The four-stroke petrol engine runs on

conventional petrol (refer to fuel recom-

mendations p4). During the first 20 op-

erating hours (break-in period) do not

use engine to maximum power. Even

after the break-in period never use

engine at higher speed than necessary

for the work in hand.

I

High engine speed is harmful

to any engine and consider-

ably affects its durability. This applies

especially for no load operation. Any

overspeed (have the engine roar) can

result in immediate damage.

Cooling System

Cooling system is fan-cooled. Therefore

keep screen at recoil starter and cool-

ing fins of the cylinder clean and free

from sucked-in plant trash.

Idling-speed

Always ensure that idling-speed is ad-

justed correctly. At low speeds and with

the speed control lever set to idle, the

engine is supposed to run smoothly and

without run-out.

Air Filter

The air filter purifies the air intake. A

blocked filter reduces engine output.

Ignition System

The engine is equipped with a contact-

less ignition system. We recommend to

have necessary check-ups done by an

expert only.

3

La pagina si sta caricando...

Briggs & Stratton 0400 Manuale del proprietario

Questo manuale è adatto anche per

Briggs & Stratton 0400 Manuale del proprietario

in altre lingue

Altri documenti