RKC INSTRUMENT COM-ML-2 Manuale utente

IMR02E08-E3

RKC INSTRUMENT INC.

EtherNet/IP

Communication Converter

CO

M

-

M

L

Instruction Manual

[For SRZ]

*00577629*

NOTICE

 EtherNet/IP is a trademark of ControlNet International Ltd. used under license by Open DeviceNet

Vendor Association, Inc. (ODVA).

 ControlLogix and RSLogix are trademarks of Rockwell Automation. RSLinx is a registered trademark

of Rockwell Automation.

 Modbus is a registered trademark of Schneider Electric.

 The name of each programmable controller (PLC) means the products of each manufacturer.

 Company names and product names used in this manual are the trademarks or registered

trademarks of the respective companies.

 This manual assumes that the reader has a fundamental knowledge of the principles of

electricity, process control, computer technology and communications.

 The figures, diagrams and numeric values used in this manual are only for explanation

purpose.

 RKC is not responsible for any damage or injury that is caused as a result of using this

instrument, instrument failure or indirect damage.

 RKC is not responsible for any damage and/or injury resulting from the use of instruments

made by imitating this instrument.

 Periodic maintenance is required for safe and proper operation of this instrument. Some

components have a limited service life, or characteristics that change over time.

 Every effort has been made to ensure accuracy of all information contained herein. RKC

makes no warranty, expressed or implied, with respect to the accuracy of the information.

The information in this manual is subject to change without prior notice.

 No portion of this document may be reprinted, modified, copied, transmitted, digitized, stored,

processed or retrieved through any mechanical, electronic, optical or other means without

prior written approval from RKC.

IMR02E08-E3 i-1

Safety Precautions

 Pictorial Symbols (safety symbols)

Various pictorial symbols are used in this manual to ensure safe use of the product, to protect

you and other people from harm, and to prevent damage to property. The symbols are

described below.

Be sure you thoroughly understand the meaning of the symbols before reading this manual.

:

This mark indicates precautions that must be

taken if there is danger of electric shock, fire,

etc., which could result in loss of life or injury.

:

This mark indicates that if these precautions

and operating procedures are not taken,

damage to the instrument may result.

: This mark indicates that all precautions

should be taken for safe usage.

 To prevent injury to persons, damage to the instrument and the equipment, a

suitable external protection device shall be required.

 All wiring must be completed before power is turned on to prevent electric

shock, fire or damage to the instrument and the equipment.

 This instrument must be used in accordance with the specifications to prevent

fire or damage to the instrument and the equipment.

 This instrument is not intended for use in locations subject to flammable or

explosive gases.

 Do not touch high-voltage connections such as power supply terminals, etc. to

avoid electric shock.

 RKC is not responsible if this instrument is repaired, modified or

disassembled by other than factory-approved personnel. Malfunction may

occur and warranty is void under these conditions.

IMR02E08-E3

i-2

● This product is intended for use with industrial machines, test and measuring equipment.

(It is not designed for use with medical equipment and nuclear energy plant.)

● This is a Class A instrument. In a domestic environment, this instrument may cause radio

interference, in which case the user may be required to take additional measures.

● This instrument is protected from electric shock by reinforced insulation. Provide reinforced

insulation between the wire for the input signal and the wires for instrument power supply,

source of power and loads.

● Be sure to provide an appropriate surge control circuit respectively for the following:

- If input/output or signal lines within the building are longer than 30 meters.

- If input/output or signal lines leave the building, regardless the length.

● This instrument is designed for installation in an enclosed instrumentation panel. All

high-voltage connections such as power supply terminals must be enclosed in the

instrumentation panel to avoid electric shock to operating personnel.

● All precautions described in this manual should be taken to avoid damage to the instrument or

equipment.

● If the equipment is used in a manner not specified by the manufacturer, the protection provided

by the equipment may be impaired.

● All wiring must be in accordance with local codes and regulations.

● To prevent instrument damage as a result of failure, protect the power line and the input/output

lines from high currents with a suitable overcurrent protection device with adequate breaking

capacity such as a fuse, circuit breaker, etc.

● A malfunction in this product may occasionally make control operations impossible or prevent

alarm outputs, resulting in a possible hazard. Take appropriate measures in the end use to

prevent hazards in the event of malfunction.

● Prevent metal fragments or lead wire scraps from falling inside instrument case to avoid electric

shock, fire or malfunction.

● Tighten each terminal screw to the specified torque found in the manual to avoid electric shock,

fire or malfunction.

● For proper operation of this instrument, provide adequate ventilation for heat dissipation.

● Do not connect wires to unused terminals as this will interfere with proper operation of the

instrument.

● Turn off the power supply before cleaning the instrument.

● Do not use a volatile solvent such as paint thinner to clean the instrument. Deformation or

discoloration may occur. Use a soft, dry cloth to remove stains from the instrument.

● Do not connect modular connectors to telephone line.



When disposing of each part used for this instrument, always follows the procedure for

disposing of industrial wastes stipulated by the respective local community.

For Proper Disposal

IMR02E08-E3

i-3

Symbols

 Pictorial Symbols (safety symbols)

: This mark indicates important information on installation, handling

and operating procedures.

: This mark indicates supplemental information on installation,

handling and operating procedures.

: This mark indicates where additional information may be located.

 Abbreviation symbols

These abbreviations are used in this manual:

Abbreviation

symbols

Name

Abbreviation

symbols

Name

PV Measured value TC (input) Thermocouple (input)

SV Set value RTD (input) Resistance temperature detector (input)

MV Manipulated output value V (input) Voltage (input)

AT Autotuning I (input) Current (input)

ST Startup tuning HBA Heater break alarm

OUT Output CT Current transformer

DI Digital input LBA Control loop break alarm

DO Digital output LBD LBA deadband

IMR02E08-E3

i-4

About This Manual

There are four manuals pertaining to this product. Please be sure to read all manuals specific to your

application requirements.

The following manuals can be downloaded from the official RKC website:

https://www.rkcinst.com/english/manual_load.htm.

Manual

Number

Remarks

EtherNet/IP Communication Converter

COM-ML [For SRZ] Installation Manual

IMR02E05-E This manual is enclosed with instrument.

This manual explains the mounting and wiring.

EtherNet/IP Communication Converter

COM-ML [For SRZ] Quick Operation Manual

IMR02E06-E This manual is enclosed with instrument.

This manual explains the communication setting

and the basic operation method.

EtherNet/IP Communication Converter

COM-ML [For SRZ] Host Communication Data List

IMR02E07-E This manual is enclosed with instrument.

This list is a compilation of the host communication

data items.

EtherNet/IP Communication Converter

COM-ML [For SRZ] Instruction Manual

IMR02E08-E3

This manual you are reading now.

This manual describes mounting, wiring,

communication setting, protocol, communication

data, troubleshooting and product specification.

Read this manual carefully before operating the instrument. Please place the manual in a

convenient location for easy reference.

IMR02E08-E3

i-5

Contents

Page

NOTICE

Safety Precautions ............................................................................................................................... i-1

 Pictorial Symbols (safety symbols) .............................................................................................. i-1

WARNING ....................................................................................................................................... i-1

CAUTION ........................................................................................................................................ i-2

For Proper Disposal .............................................................................................................................. i-2

Symbols ................................................................................................................................................ i-3

 Pictorial Symbols (safety symbols) .............................................................................................. i-3

 Abbreviation symbols ................................................................................................................... i-3

About This Manual ................................................................................................................................ i-4

1. OUTLINE .............................................................................. 1

1.1 Checking the Product ..................................................................................... 2

1.2 Model Code .................................................................................................... 3

1.3 Parts Description ............................................................................................ 4

2. HANDLING PROCEDURES ................................................ 6

3. MOUNTING .......................................................................... 7

3.1 Mounting Cautions .......................................................................................... 7

3.2 Dimensions ..................................................................................................... 9

3.3 DIN Rail Mounting .......................................................................................... 9

3.4 Panel Mounting ............................................................................................. 11

4. WIRING .............................................................................. 12

4.1 Wiring Cautions ............................................................................................ 12

4.2 Terminal Configuration ................................................................................. 13

4.3 Connection to EtherNet/IP ............................................................................ 14

4.4 Connection to Host Computer ....................................................................... 16

4.4.1 When connected with RS-422A ............................................................................................... 16

4.4.2 When connected with RS-485 ................................................................................................. 18

4.4.3 Connections for loader communication ................................................................................... 20

IMR02E08-E3

i-6

Page

5. HOST COMMUNICATION SETTING ................................. 2 1

5.1 Address Setting ............................................................................................ 21

5.2 DIP Switch Setting ........................................................................................ 22

6. COMMUNICATION SETTING OF

SRZ FUNCTION MODULE ................ 23

6.1 Address Setting of the Function Modules ..................................................... 23

6.2 Temperature Control Channel of the SRZ Unit ............................................. 24

6.3 Digital Input/Output Channel of Z-DIO Module ............................................. 25

7. INITIAL COMMUNICATION DATA SETTING ................... 26

7.1 IP Address Setting ........................................................................................ 26

7.2 EtherNet/IP Communication Settings ........................................................... 29

7.3 Other Communication Data Settings ............................................................ 34

8. EtherNet/IP ......................................................................... 35

8.1 Outline of EtherNet/IP .................................................................................... 35

8.2 Communication Method ................................................................................. 37

9. COMMUNICATION DATA LIST ......................................... 38

9.1 Reference to Communication Data List ........................................................ 38

9.2 Communication Data of COM-ML ................................................................. 40

9.3 Communication Data of Z-TIO Module ......................................................... 43

9.4 Memory Area Data Address of Z-TIO Module ............................................... 66

9.5 Communication Data of Z-DIO Module ......................................................... 68

10. USAGE EXAMPLE ........................................................... 73

10.1 Handling Procedures ................................................................................... 73

10.2 System Configuration .................................................................................. 74

10.3 Use Instruments Settings ............................................................................ 75

10.4 Initial Communication Data Settings ........................................................... 75

10.5 Tool Settings ............................................................................................... 76

10.6 I/O Communication ..................................................................................... 84

10.7 Explicit Message Communication ............................................................... 87

IMR02E08-E3

i-7

Page

11. TROUBLESHOOTING ...................................................... 93

12. SPECIFICATIONS ............................................................ 98

13. OBJECT MODEL ............................................................ 102

13.1 CIP Common Object .................................................................................. 102

13.2 Application Object ...................................................................................... 106

APPENDIX. HOST COMMUNICATION PROTOCOL .......... 108

A.1 Communication Requirements .................................................................... 108

A.2 RKC Communication Protocol .................................................................... 110

A.2.1 Polling procedures ............................................................................................................... 110

A.2.2 Selecting procedures ........................................................................................................... 116

A.2.3 Communication data structure ............................................................................................. 121

A.3 Modbus Protocol ......................................................................................... 123

A.3.1 Message format ................................................................................................................... 123

A.3.2 Function code ...................................................................................................................... 124

A.3.3 Communication mode .......................................................................................................... 124

A.3.4 Slave responses .................................................................................................................. 125

A.3.5 Calculating CRC-16 ............................................................................................................. 126

A.3.6 Register read and write ....................................................................................................... 129

A.3.7 Data processing precautions ............................................................................................... 133

A.3.8 How to use memory area data ............................................................................................ 134

IMR02E08-E3

i-8

MEMO

IMR02E08-E3 1

1. OUTLINE

EtherNet/IP communication converter COM-ML [For SRZ] (hereafter called COM-ML) is communication

converter to connect the RKC module type controller SRZ to the EtherNet/IP.

This chapter describes features, package contents, model code, system configuration, etc.

• EtherNet/IP is an implementation of CIP (Common Industrial Protocol) on Ethernet and TCP/IP.

• COM-ML supports “I/O communication” and “Explicit message communication” for EtherNet/IP.

• Scanner/adapter (multicast: 1 to N) communication is used in I/O communication.

Client/server (peer to peer: 1 to 1) communication is used in explicit message communication.

• In scanner/adapter communication, COM-ML corresponds to the adapter. In client/server

communication, COM-ML corresponds to the server.

• Up to 30 function modules (Z-TIO and Z-DIO) can be connected to one COM-ML with SRZ unit.

(However, the maximum joinable number of function modules of the same type is 16.)

SRZ Unit

Host computer

or

Operation panel

Z-TIO-A/B or Z-DIO-A module

(Up to 30 modules)

EtherNet/IP

or

Ethernet

RKC communication

Modbus

RS-485

RS-422A

EtherNet/IP communication converter

COM-ML

[Adapter or Server]

Programmable

controller

(PLC)

[Scanner or Client]

Host

computer

Network Hub

Ethernet

EtherNet/IP

For EtherNet/IP, see the website of ODVA (Open DeviceNet Vendor Association).

URL: https://www.odva.org/

1. OUTLINE

IMR02E08-E3

2

1.1 Checking the Product

Before using this product, check each of the following:

 Model code

 Check that there are no scratch or breakage in external appearance (case, front panel, or terminal, etc.)

 Check that all of the items delivered are complete. (See below)

Name Q’TY Remarks



COM-ML [For SRZ] Installation Manual (IMR02E05-E) 1 Enclosed with instrument



COM-ML [For SRZ] Quick Instruction Manual (IMR02E06-E) 1 Enclosed with instrument



COM-ML [For SRZ] Communication Data List (IMR02E07-E) 1 Enclosed with instrument



Joint connector cover KSRZ-517A 2 Enclosed with instrument



Power terminal cover KSRZ-518A 1 Enclosed with instrument



COM-ML [For SRZ] Instruction Manual (IMR02E08-E3) 1 This manual (sold separately)

This manual can be downloaded from

the official RKC website:

https://www.rkcinst.com/english/

manual_load.htm

If any of the products are missing, damaged, or if your manual is incomplete, please contact

RKC sales office or the agent.

EDS file

The EDS file is used for recognition of the COM-ML on EtherNet/IP in the configuration tool

(software for environment settings and creating programs); however, EtherNet/IP communication

is possible without using the EDS file.

If you require the EDS file, download it from the official RKC website.

https://www.rkcinst.com/english/manual_load.htm

 Accessories (sold separately)

Name Q’TY Remarks



End plate DEP-01 2 Secures the SRZ on the DIN rail



Communication converter COM-K2-1 1 For loader communication

(Option: with loader communication cable)



Connection cable (W-BF-01-, : cable length) 1 For host communication

Modular connector and Spade lug terminal



Connection cable (W-BF-02-, : cable length) 1 For host communication

Modular connectors (at both ends)



Connection cable (W-BF-28-, : cable length) 1 For host communication

Modular connector and D-sub 9-pin connector

1. OUTLINE

IMR02E08-E3

3

1.2 Model Code

Check whether the delivered product is as specified by referring to the following model code list.

If the product is not identical to the specifications, please contact RKC sales office or the agent.

(1) Ethernet communication type

2: EtherNet/IP

(2) Host communication interface (COM. PORT)

4: RS-422A

5: RS-485

(3) Corresponding to the RKC controller

02: SRZ

COM- ML - 2 □∗ 02

(1) (2) (3)

1. OUTLINE

IMR02E08-E3

4

1.3 Parts Description

 COM-ML mainframe

Loade

r

communication

connecto

r

Indication lamp RX/TX

Indication lamp FAIL/RUN

Host communication

address setting switch

Communication

port

COM. PORT

Indication lamp NS

EtherNet/IP

communication

connecto

r

Left side view

DIP switch

Front view

Indication lamp LINK

Indication lamp MS

COM-ML

FAIL/RU N

LOADER

RX/T

X

COM.PORT

NS MS

LINK

EtherNet/IP

Base

 Indication lamps

FAIL/ RUN [Green or Red] • When normal: A green lamp is on (RUN)

• During setting of default IP address setting: A green lamp flashes (RUN)

• Self-diagnostic error (Recoverable fault): A green lamp flashes (FAIL)

• Self-diagnostic error (Major fault): A red lamp is on (FAIL)

RX/TX [Green] During host communication data send and receive: A green lamp turns on

NS (Network status)

[Green or Red]

• No power or no IP address: Turns off

• Online, no connection established: A green lamp flashes

• Online, connections established: A green lamp turns on

• I/O connection is timeout: A red lamp flashes

• A fatal communications error has occurred (Duplicate IP address):

A red lamp turns on

LINK (Link/Activity) [Green] • No link, no activity: Turns off

• Activity (During data send): A green lamp flashes

• Link established: A green lamp turns on

MS (Module status)

[Green or Red]

• No power: Turns off

• Controlled by a Scanner in Run state: A green lamp turns on

• Not configured, or Scanner in idle state: A green lamp flashes

• Recoverable fault: A red lamp flashes

• Major fault: A red lamp turns on

 Communication port (modular connector) and communication connector

COM. PORT Use to connecting the Operation panel or Host computer. [RS-485 or RS-422A]

EtherNet/IP communication

connector

Use to connecting the EtherNet/IP.

Loader communication connector Use to connecting the communication converter and personal computer when

loader communication is performed.

 Switch

Host communication address

setting switch

Sets unit address for host communication.

DIP switch

• Sets the communication speed and communication protocol corresponding to

host communication.

• Sets dip switch setting validity/invalidity.

• Sets the default IP address settings.

1. OUTLINE

IMR02E08-E3

5

 Base

Mounting holes (M3 screw)

Power supply

terminals

Joint connector

Mounting

bracket

Terminal 3, 4 and 5

Usage is prohibited.

Front Rear

Mounting holes (M3 screw)

Holes for screws to fix the base to a panel, etc.

Customer must provide the M3 screws.

Joint connector

Used to mechanically and electrically connect each module.

Power supply terminals

These are terminals to supply power to the COM-ML and joined function modules.

Terminal number Signal name

1 24 V DC (+)

2 24 V DC (−)

Terminal 3, 4 and 5

These terminals cannot be used for the COM-ML. (Usage is prohibited.)

When the COM-ML is connected to a function module, do not use

terminals 3, 4 and 5 of the function module.

Mounting bracket

Used to fix the module on DIN rails and also to fix each module joined together.

6 IMR02E08-E3

2. HANDLING PROCEDURES

Conduct necessary setting before operation according to the procedure described below.

Mounting

Install the COM-ML.

• See 3. MOUNTING (P. 7).

• For controller (SRZ), see Z-TIO Instruction Manual

(IMS01T01-E) and Z-DIO Instruction Manual

(IMS01T03-E).

Host communication

settings

Wiring

Controller (SRZ) settings

IP address settings

The address, communication speed, communication protocol, data bi

t

configuration, and DIP switch setting validity/invalidity of hos

t

communication are set only when host communication is used in the

COM-ML.

See 5. HOST COMMUNICATION SETTINGS (P. 21).

Connect the COM-ML power wiring and the controller (SRZ) wiring,

and connect the COM-ML to the scanner (or client). Connect the

wiring for host communication or loader communication in the

COM-ML.

• See 4. WIRING (P. 12)

• For controller (SRZ), see Z-TIO Instruction Manual

(IMS01T01-E) and Z-DIO Instruction Manual

(IMS01T03-E).

Set the communication setting of controller (SRZ).

• See 6. COMMUNICATIOM SETTING OF SRZ

FUNCTION MODULE (P. 23).

• For controller (SRZ), see Z-TIO Instruction Manual

(IMS01T01-E) and Z-DIO Instruction Manual

(IMS01T03-E).

Set the IP address of COM-ML.

See 7.1 IP Address Settings (P. 26).

EtherNet/IP

communication settings

Configure initial settings for EtherNet/IP communication.

• See 7.2 EtherNet/IP Communication Setting (P. 29).

• See 10.5 Tool Settings (P. 76).

Other communication

data settings

Set the data for the COM-ML and controller (SRZ).

• See 7.3 Other Communication Data Settings (P. 34).

• See 9. COMMUNICATION DATA LIST (P. 38).

EtherNet/IP

communication

Execute I/O communication or explicit message communication.

• See 10.6 I/O Communication (P. 84).

• See 10.7 Explicit Message Communication (P. 87).

IMR02E08-E3 7

3. MOUNTING

This chapter describes installation environment, mounting cautions, dimensions and mounting procedures.

3.1 Mounting Cautions

(1) This instrument is intended to be used under the following environmental conditions.

(IEC 61010-1) [POLLUTION DEGREE 2]

(2) Use this instrument within the following environment conditions.

• Allowable ambient temperature: −10 to +50 °C

• Allowable ambient humidity: 5 to 95 %RH

(Absolute humidity: MAX.W.C 29.3 g/m

3

dry air at 101.3 kPa)

• Installation environment conditions: Indoor use

Altitude up to 2000 m

(3) Avoid the following conditions when selecting the mounting location:

• Rapid changes in ambient temperature which may cause condensation.

• Corrosive or inflammable gases.

• Direct vibration or shock to the mainframe.

• Water, oil, chemicals, vapor or steam splashes.

• Excessive dust, salt or iron particles.

• Excessive induction noise, static electricity, magnetic fields or noise.

• Direct air flow from an air conditioner.

• Exposure to direct sunlight.

• Excessive heat accumulation.

(4) Mount this instrument in the panel considering the following conditions:

• Provide adequate ventilation space so that heat does not build up.

• Do not mount this instrument directly above the equipment that generates large amount of heat

(heaters, transformers, semi-conductor functional devices, large-wattage resistors.)

• If the ambient temperature rises above 50 °C, cool this instrument with a forced air fan, cooler, or the

like. Cooled air should not blow directly on this instrument.

• In order to improve safety and the immunity to withstand noise, mount this instrument as far away as

possible from high voltage equipment, power lines, and rotating machinery.

High voltage equipment: Do not mount within the same panel.

Power lines: Separate at least 200 mm

Rotating machinery: Separate as far as possible

• For correct functioning mount this instrument in a horizontal position.

To prevent electric shock or instrument failure, always turn off the power before

mounting or removing the instrument.

3. MOUNTING

IMR02E08-E3

8

• Space required between each module vertically

When the module is mounted on the panel, allow a

minimum of 50 mm at the top and bottom of the

module to attach the module to the mainframe.

• Depth for modular cables mount type

module

Space for modular cables must be considered

when installing.

• It is recommended to use a plastic cover on the connector on both sides of the mounted modules for

protection of connectors.

Joint connector cove

r

• Be sure the COM-ML and SRZ function modules (Z-TIO and Z-DIO modules) are joined when

using them.

(5) In case this instrument is connected to a supply by means of a permanent connection, a switch or

circuit-breaker shall be included in the installation. This shall be in close proximity to the equipment

and within easy reach of the operator. It shall be marked as the disconnecting device for the equipment.

50 mm or more

COM

76.9 mm

Communication

cable

Approx.

50 mm

3. MOUNTING

IMR02E08-E3

9

3.2 Dimensions

76.9

30 6.7

100

5

4.7

(Unit: mm)

3.3 DIN Rail Mounting

 Mounting procedures

1. Pull down the mounting bracket at the bottom of the module (A). Attach the hooks on the top of the

module to the DIN rail and push the lower section into place on the DIN rail (B).

2. Slide the mounting bracket up to secure the module to the DIN rail (C).

(B) Push

Mounting

bracket

DIN rail

(A) Pull down

(C) Locked

3. MOUNTING

IMR02E08-E3

10

 Module joining procedures

1. Mount the function modules on the DIN rail. Slide the modules until the modules are closely joined

together and the joint connectors are securely connected.

(Front view of module mainframe)

Joint connector

Function module

COM-ML

2. Push in the mounting brackets to lock the modules

together and fix to the DIN rail.

After module joining, install a

plastic cover on the

connector on both sides of the mounted modules for

protection of connectors. (See P. 8)

To firmly fix the modules, use end plates (DEP-01)

sold separately on both sides of the mounted

modules.

 Removing procedures

1. Turn the power OFF.

2. Remove the wiring.

3. Pull down a mounting bracket with a

blade screwdriver (A). Lift the module

from bottom, and take it off (B).

(A) Pull down

(B) Lift and take off

(Rear view of base)

Push in all of the mounting brackets.

Mounting

bracket

State where each

module is locked.

La pagina sta caricando ...

RKC INSTRUMENT COM-ML-2 Manuale utente

RKC INSTRUMENT COM-ML-2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti