Zanussi FLS572 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente
20
YOUR NEW WASHING MACHINE
i
This new washing machine meets all
requirements for a modern washing of laundry
with reduced consumption of water, energy and
detergent.
The temperature selector dial allows you to
choose personally the suitable washing
temperature for your laundry.
The automatic cooling of the washing water
from 90°C to 60°C before draining will prevent
plastic pipes of your drainage system from
being deformed.
Ecological hints
In order to obtain water and energy savings and
to protect the environment, we advice you to
follow these instructions:
Whenever possible, wash the maximum load
for the selected programme, without
overloading the drum.
Use a programme with prewash only for heavy
soiled items.
Measure out detergent according to the water
hardness, degree of soiling and quantity of
laundry being washed.
Use a short programme when washing lightly
soiled laundry.
Environment protection
Packaging recycling
Materials marked with the symbol are
recyclable. To enable them to be recycled, they
must be placed in the appropriate collection
areas (or containers). Check with your local
authorities.
>PE<= polyethylene
>PS<= polystyrene
>PP<= polypropylene
Washing machine scrapping
When the appliance is to be scrapped, cut off the
power supply cable and make the door closing
device inoperative to avoid it becoming a death
trap for a child.
For correct disposal of the machine, contact your
local authority department which provides for
collection of urban solid refuse.
i
The symbols you will see on some paragraphs of this booklet have the following meaning:
Important information concerning the
safety in the use of your machine.
Disregarding this information might
lead to damages.
Information for correct use of your
machine and to obtain the best
performance.
Important information concerning
environment protection.
Our contribution to the protection of the
environment: we use recycled paper.
21
EN
G
LI
S
H
CONTENTS
Important information . . . . . . . . . . . .22
Description of the appliance . . . . .23
Detergent dispenser drawer . . . . . . . . . . .23
Technical specifications . . . . . . . . . .23
Installation . . . . . . . . . . . . . . . . . . . . . . .24
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . .24
Positioning . . . . . . . . . . . . . . . . . . . . . . . . .24
Water inlet . . . . . . . . . . . . . . . . . . . . . . . . .25
Water drainage . . . . . . . . . . . . . . . . . . . . .25
Electrical connection . . . . . . . . . . . . . . . . .25
Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Control panel . . . . . . . . . . . . . . . . . . . . . .26
Washing hints . . . . . . . . . . . . . . . . . . . . . .27
Sorting the laundry . . . . . . . . . . . . . . . . . .27
Temperatures . . . . . . . . . . . . . . . . . . . . . .27
Before loading the laundry . . . . . . . . . . . .27
Maximum loads . . . . . . . . . . . . . . . . . . . .27
Laundry weights . . . . . . . . . . . . . . . . . . . .27
Removing stains . . . . . . . . . . . . . . . . . . .27
Detergents and additives . . . . . . . . . . . . .28
International wash code symbols . . . . . . . .29
Washing programmes . . . . . . . . . . . . . .30-31
Operating sequence . . . . . . . . . . . . . . .32-33
Maintenance . . . . . . . . . . . . . . . . . . . . . .34
Bodywork . . . . . . . . . . . . . . . . . . . . . . . . . .34
Detergent dispenser drawer . . . . . . . . . . . .34
Water inlet filter . . . . . . . . . . . . . . . . . . . . .34
Drain filter . . . . . . . . . . . . . . . . . . . . . . . . .35
Emergency emptying out . . . . . . . . . . . . . .35
The dangers of freezing . . . . . . . . . . . . . . .35
Something not working . . . . . . . .36-37
22
IMPORTANT INFORMATION
Installation
When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
All internal packing must be removed before
using the appliance. Serious damage may be
caused to the machine or adjacent furniture if
the protective transit devices are not removed
or are not completely removed. Refer to the
relevant paragraph in the instruction book.
Any electrical work required to install this
appliance must be carried out by a qualified
electrician.
Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
After having installed the machine, check that
it is not standing on its electrical supply cable.
If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between
the adjustable feet and the floor.
Use
This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
Do not overload the appliance. Follow the
instructions in the instruction book.
Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
Make sure that all pockets are empty. Objects
such as coins, safety pins, pins and screws
can cause extensive damage.
Do not machine wash garments saturated
with petroleum, methylated spirits,
trichlorethylene, etc. If such fluids have been
used to remove stains prior to washing, wait
until they have completely evaporated from
the fabric before placing garments in the
appliance.
Place small items such as socks, belts, etc. in
a cloth bag or pillowcase to prevent them
getting trapped between the drum and the
tub.
Use only the recommended quantities of
fabric softener. An excessive amount could
damage the laundry.
Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the
door seal and prevents the formation of musty
smells.
Always check that water has emptied out
before opening the door. If not, drain the
water following the instructions in the
instruction book.
Always unplug the appliance and shut the
water tap after use.
Service/repair
In the event of a fault, do not attempt to repair
the appliance yourself. Repairs carried out by
inexperienced persons may cause damage.
If repairs are needed, contact an authorised
service centre and ask for genuine spare
parts.
Safety
This appliance is designed to be used by
adults. Children must not be allowed to touch
the controls or play with the product.
During high temperature wash cycles the
glass door becomes very hot. Do not touch it.
Pets sometimes climb into washing machines.
Check the drum before each use.
It is important that this instruction book be kept with the appliance for future reference. If you sell or
give the appliance away, make sure that the book is passed to the new owners so that they can
familiarise themselves with its operation and relevant warnings.
The following warnings are provided in the interests of overall safety. You must read them carefully
before installing or using the appliance.
23
EN
G
LI
S
H
DESCRIPTION OF THE APPLIANCE
01 Detergent dispenser drawer
02 Programme chart
03 Option buttons
04 Temperature selector dial
05 Operating pilot light
06 Programme selector dial
07 Door handle
08 Drain filter
09 Adjustable feet
Detergent dispenser drawer and
programme chart
Symbols
Prewash
Main wash
Bleaching agent
Fabric softener
There is a programme guide in Spanish
language on the front of the drawer.
8
7
9
2
65431
P0446
Cl
TECHNICAL SPECIFICATIONS
DIMENSIONS Height 85 cm
Width 60 cm
Depth 54 cm
POWER SUPPLY VOLTAGE/FREQUENCY 220-230V/50 Hz
TOTAL POWER ABSORBED 2250 W
MINIMUM FUSE PROTECTION 10 A
WATER PRESSURE Minimum 5 N/cm
2
Maximum 80 N/cm
2
MAXIMUM LOAD Cotton 4.5 kg
Synthetics, delicate fabrics 2.0 kg
Woollens 1.0 kg
SPIN SPEED 500 rpm
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility
24
INSTALLATION
Unpacking
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the rear
right-hand bolt and lay the machine on its
back, taking care not to squash the hoses.
This can be avoided by placing one of the
corner packing pieces between the machine
and the floor.
2. Remove the polystyrene block from the bottom
of the machine and release the two plastic
bags by removing the adhesive strip.
3. Carefully remove the right-hand bag (1) then
the left-hand bag (2) by pulling them towards
the centre of the machine.
4. Set the machine upright and remove the two
remaining bolts from the back.
5. Pull out the three plastic spacers from the
holes into which the bolts were fitted.
6. Plug the open holes with the plugs which you
will find at the back of the appliance.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units.
Carefully level by screwing the adjustable feet in
or out. Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
After having levelled the machine, tighten the lock
nuts.
P0255
P0234
P0233
2
1
P0256
P0020
P0254
P0509
All transit bolts and packing must be
removed before using the appliance.
25
EN
G
LI
S
H
Water inlet
Connect the water inlet hose to a tap with a 3/4"
thread after having inserted the small filter “A”
supplied with the machine.
The other end of the inlet hose which connects to
the machine can be turned in any direction.
Simply loosen the fitting, rotate the hose and
retighten the fitting, making sure there are no
water leaks.
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you
will have to purchase a new, longer hose
specially designed for this type of use.
Water drainage
The end of the drain hose can be positioned in
three ways:
Hooked over the edge of a sink using the
plastic hose guide supplied with the machine.
In this case, make sure the end cannot come
unhooked when the machine is emptying.
This could be done by tying it to the tap with a
piece of string or attaching it to the wall.
In a sink drain pipe branch. This branch must
be above the trap so that the bend is at least
60 cm above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter of
the drain hose.
The drain hose must not be kinked. Run it along
the floor; only the part near the drainage point
must be raised.
Electrical connection
This machine is designed to operate on a 220-
230 V, single-phase, 50 Hz supply.
Check that your domestic electrical installation
can take the maximum load required (2.25 kW),
also taking into account any other appliances in
use.
Connect the machine to an earthed socket.
A
P0003
P0022
P0023
P0021
The manufacturer declines any
responsibility for damage or injury
through failure to comply with the above
safety precaution.
26
USE
Control panel
123 456
Blancos con prelav.
Sintéticos con prelav.
Lavado rápido
Aclarados
Suavizantes
Centrifugado
Descarga
60º- 90º
30º- 60º
30º- 40º
A
J
D
F
G
H
Q
N
P
Blancos
Colores resistentes
Colores delicados
Sintéticos
Delicados
Lana
B
B
C
K
L
M
60º- 90º
40º- 60º
30º- 40º
30º- 60º
30º- 40º
30º- 40º
1 Detergent dispenser drawer
2 Half load button
Select this button to reduce water consumption
on the rinse cycle when washing a smaller load
of cottons or linens (max. load size=2.25 kg).
The machine will carry out 3 rinses instead of 4.
3 Spin suppression button
Depress this button when washing particularly
delicate cotton or linen items in order to exclude
all the spinning phases.
4 Temperature selector dial
Turn this dial to select the washing temperature.
Position = cold wash.
5 Operating pilot light
This light is on whilst the machine is operating
and goes out at the end of the programme.
6 Programme selector dial/
ON/OFF switch
To select the required programme, turn this dial
clockwise until the programme letter is exactly
opposite the pointer.
To start the programme pull the dial outwards.
To switch the machine off depress the dial.
Before changing an ongoing programme the
machine must be switched off by depressing
the dial.
27
EN
G
LI
S
H
Washing hints
Sorting the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing
instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
Temperatures
90°
for normally soiled white cottons and
linen (e.g. tea cloths, towels,
tablecloths, sheets...)
60° for normally soiled, colour fast
garments (e.g. shirts, night dresses,
pyjamas....) in linen, cotton or
synthetic fibres and for lightly soiled
white cotton (e.g. underwear).
(cold)
30°-40°
for delicate items (e.g. net curtains),
mixed laundry including synthetic
fibres and woollens bearing the label
«pure new wool, machine washable,
non-shrink»
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their “whiteness” in the wash.
New coloured items may run in the first wash;
they should therefore be washed separately the
first time.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent
or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
Maximum loads
Recommended loads are indicated in the
programme charts.
General rules:
cotton, linen: drum full but not too tightly packed
synthetics: drum no more than half full
delicate fabrics and woollens: drum no more
than one third full
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load size.
Laundry weights
The following weights are indicative:
bathrobe 1200 g
napkin 100 g
quilt cover 700 g
sheet 500 g
pillow case 200 g
tablecloth 250 g
towelling towel 200 g
tea cloth 100 g
night dress 200 g
ladies’ briefs 100 g
man’s work shirt 600 g
man’s shirt 200 g
man’s pyjamas 500 g
blouse 100 g
men’s underpants 100 g
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab
the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and
the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach (whites
and fast coloureds only).
Ball point pen and glue: moisten with acetone
(*), lay the garment on a soft cloth and dab the
stain.
i
28
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove any
residual marks from white fabrics with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
(*) do not use acetone on artificial silk
Detergents and additives
Good washing results also depend on the choice
of detergent and use of the correct quantities to
avoid waste and protect the environment.
Although biodegradable, detergents contain
substances which, in large quantities, can upset
the delicate balance of nature.
The choice of detergent will depend on the type
of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of
soiling.
All commonly available washing machine
detergents may be used in this appliance:
powder detergents for all types of fabric,
powder detergents for delicate fabrics (60°C
max) and woollens,
liquid detergents, preferably for low
temperature wash programmes (60°C max) for
all types of fabric, or special for woollens only.
The detergent and any additives must be placed
in the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents,
a programme without prewash must be selected.
Pour liquid detergent into the dispenser drawer
compartment marked just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked before
starting the wash programme.
The bleaching agent (chlorine) can be used only
for white or fast coloured cotton and linen items.
Pour it into the compartment marked .
Follow the product manufacturer’s
recommendations on quantities to use.
Quantity of detergent to be used
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Water hardness is classified in so-called
“degrees” of hardness. Information on hardness
of the water in your area can be obtained from
the relevant water supply company, or from your
local authority.
Follow the product manufacturers’ instructions on
quantities to use.
Use less detergent if:
you are washing a small load
the laundry is lightly soiled
large amounts of foam form during washing.
0,0-15
16-25
26-37
more than 37
Level
1
2
3
4
soft
medium
hard
very hard
00-07
08-14
15-21
more than 21
Characteristic
Degrees
German
°dH
French
°T.H.
Degrees of water hardness
29
EN
G
LI
S
H
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
i
Energetic wash
Delicate wash
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Hand wash Do not
wash
at all
Bleaching Bleach in cold water Do not bleach
Ironing Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
Drying Flat On the line On clothes
hanger
Tumble dry
high
temperature
low
temperature
Do not
tumble dry
A
P
F
95
60
60
40
40
40
30
30
30
Energetic programmes for cotton and linen
Maximum load: 4.5 kg
Progr.
A
Temp. Type of laundry Cycle description
Possible
options
60°-90°
Whites
with prewash
(heavy soiled)
Prewash
Wash at 60°-90°C
4 rinses
Long spin
B
Whites
without prewash
(normally soiled)
Wash at 60°-90°C
4 rinses
Long spin
B
(•)
Fast coloureds
without prewash
(normally soiled)
Wash at 40°-60°C
4 rinses
Long spin
Rinses
C
Spin
F
The temperatures indicated are the optimum temperatures for each programme and depend on the
type of laundry and degree of soiling.
(•) This programme at 60°C is the reference programme for the Energy label according to the EEC
Directive 92/75:
water 74 litres
energy 1.3 kWh
time 135 mins
Drain and long spin
60°-90°
40°-60°
H
4 rinses with liquid
additives, if required
Long spin
Softeners
G
1 rinse with additive
Long spin
Wash at 30°-40°C
4 rinses
Long spin
30°-40°
No-fast coloureds
(normally soiled)
D
Wash at 30°-40°C
4 rinses
Long spin
30°-40°
Quick wash
(lightly soiled laundry)
31
EN
G
LI
S
H
30°-40°
Woollens
Gentle programmes for synthetics, mixed fibres, delicates and woollens
Maximum load: 2 kg, woollens: 1kg
Progr. Temp. Type of laundry Cycle description
Possible
option
J
30°-60°
Synthetics
with prewash
(heavy soiled)
Prewash
Wash at 30°-60°C
3 rinses
Stop with water in the tub
K
30°-60°
Synthetics
without prewash
(normally soiled)
Wash at 30°-40°C
3 rinses
Stop with water in the tub
L
Wash at 30°-60°C
3 rinses
Stop with water in the tub
Rinses
3 rinses with fabric softener
Stop with water in the tub
M
The temperatures indicated are the optimum temperatures for each programme and depend on the
type of laundry and degree of soiling.
The last rinse water of these programmes is not emptied out to prevent any creasing in the laundry.
To drain water select programme H or Q.
N
Delicate fabrics - Silk
30°-40°
Wash at 30°-40°C
3 rinses
Stop with water in the tub
Softeners
P
1 rinse with fabric softener
Stop with water in the tub
Drain
Draining of water
Q
32
P0004
P0444
90
P0345
P0445
Before washing your first load of laundry, we
recommend that you run a cotton cycle at 60°C,
with the machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main
wash compartment and start up the machine.
1. Place the laundry in the drum
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent
recommended by the manufacturer in a
graduated cup and pour it into the main wash
compartment . If you wish to carry out a
prewash, pour detergent into the appropriate
compartment marked .
3. Measure out the additives
If required, pour fabric softener into the
compartment marked and the bleaching agent
into the compartment marked without
exceeding the «MAX» mark.
4. Select the desired option(s)
5. Select the temperature
Turn the selector dial to the required temperature
setting.
Operating sequence
33
EN
G
LI
S
H
6. Select the programme and start it
Turn the programme selector dial clockwise to
the required wash programme and pull it
outwards: the operating pilot light comes on and
the machine starts to operate.
7. At the end of the programme
The machine stops automatically, the operating
pilot light goes out.
If you have selected a gentle programme which
stops with water in the tub, drain the water before
opening the door.
It is normal to have to wait for about 2 minutes
before being able to open the door to allow the
safety lock to release.
Depress the programme selector dial.
Remove the laundry.
Turn the drum by hand to make sure it is
completely empty, so as to avoid any forgotten
items being damaged in a subsequent wash (e.g.
shrinking) or their colour running into a load of
whites.
Release any buttons which have been pressed.
Turn the water tap off and unplug the machine.
Leave the door ajar to air the machine.
P0215
B
P0216
B
34
MAINTENANCE
P0442
P0038
P0041
1. Bodywork
Clean the outside of the machine with warm
water and a neutral, non-abrasive household
detergent. Rinse with clean water and dry with a
soft cloth.
Important: do not use methylated spirits,
solvents or similar products to clean the
bodywork.
2. Detergent dispenser drawer
After a while, detergents and fabric softeners
leave deposits in the drawer.
Clean the drawer from time to time by rinsing it
under a running tap. To remove the drawer from
the machine, press the button in the rear left-
hand corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
Detergent can also eventually accumulate inside
the drawer recess: clean it with an old
toothbrush. Refit the drawer after cleaning.
3. Water inlet filter
If you notice that the machine is taking longer to
fill, check that the filter in the water inlet hose is
not blocked.
Turn off the water tap.
Unscrew the hose from the tap and remove the
filter.
Clean it with a stiff brush.
Refit the filter and screw the hose back onto the
tap.
P0443
35
EN
G
LI
S
H
4. Drain filter
The drain filter collects threads and small objects
inadvertently left in the laundry. Check regularly
that the filter is clean.
Open the filter door.
Place a container under the filter and unscrew it.
Pull out the filter.
Clean the filter under a running tap, then refit it,
screwing it fully in.
5.Emergency emptying out
If the water is not discharged (drain pump is
blocked, filter or drain hose are clogged),
proceed as follows to empty out the machine:
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has cooled
down;
place a bowl on the floor;
put the drain hose end into the bowl and let
the water come out.
Should it not be possible to have access to the
drain hose because, for example, the appliance
is built in the kitchen furniture, slightly loosen the
drain filter after placing a bowl on the floor, to let
the water come out slowly.
At the end screw the filter again.
P0011
P0132
P0133
P0040
6. The dangers of freezing
If the machine is exposed to temperatures below
0°C, certain precautions should be taken.
Turn off the water tap.
Unscrew the inlet hose.
Unhook the drain hose from the rear support
and position the end of this hose and that of
the inlet hose in a bowl. Run the draining
programme until the selector dial is in the
“Stop” position.
Disconnect the appliance.
Screw the inlet hose and reposition the drain
hose.
When you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
36
SOMETHING NOT WORKING
Problem Possible cause
The machine does not start up:
Check that the door is firmly closed.
Check that the machine is plugged in and
that there is power at the socket.
Check that the main fuse has not blown.
Check that the programme selector dial is
positioned correctly and pulled out.
The machine does not fill:
Check that the water tap is open.
Check that water is coming out of the tap.
Check that the inlet hose is not squashed or
kinked.
Check that the filter in the inlet hose is not
blocked.
Check that the door is closed.
The machine does not empty
and/or does not spin:
Check that the drain hose is not squashed or
kinked.
The drain filter is blocked. Clean it.
A gentle programme has been selected.
The spin suppression option has been
selected (only for cotton).
There is water on the floor:
Too much detergent or unsuitable detergent
(creates too much foam) has been used.
Check whether there are any leaks from one
of the inlet hose fittings. It is not always easy
to see this as the water runs down the hose;
check to see if it is damp.
Check that the drain hose is not damaged.
Check that the drain filter has been refitted
correctly after cleaning.
Unsatisfactory washing results
Too little detergent or unsuitable detergent
has been used.
Stubborn stains have not been treated prior
to washing.
The correct temperature or programme was
not selected.
The machine fills then empties
immediately
The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage”
section.
Problems which you can resolve yourself
37
EN
G
LI
S
H
Problem Possible cause
The machine vibrates or is noisy:
Check that all the transit bolts and packing
have been removed.
Check that the machine is not resting against
anything.
Check that the support feet are resting firmly
on the ground and that the lock nuts are
securely tightened.
Check that the laundry is evenly distributed in
the drum.
Maybe there is very little laundry in the drum.
The door will not open:
The programme is still running.
The door lock has not yet been released.
There is water in the drum.
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and
purchase date of your machine: the Service
Centre will require this information.
Mod. ..........
Prod. No. ...........
Ser. No. .........
Mod.
..........
Ser.
P0042
P1035UK
Water is not
visible in the machine. The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption. Performance is
nevertheless excellent.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Zanussi FLS572 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente

in altre lingue