ADEMCO Security System VISTA-15 Guida d'installazione

K3892V1 4/00

9,67$

9,67$&1

6HF XULW\6\VWHP

,QVWDOODWLRQDQG6HWXS*XLGH

•

*

®

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation & Setup Guide

ii

www.PDF-Zoo.com

iii

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations for the location of Fire and Burglary Detection

Devices Help Provide Proper Coverage for the Protected Premises.

Recommendations for Smoke and Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations

contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.

Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms

and areas of the household as follows: For minimum protection, a smoke detector should be installed

outside of each separate sleeping area and on each additional floor of a multi-floor family living unit,

including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or

in garages is not normally recommended.

For additional protection, the NFPA recommends that you install heat or smoke detectors in the living

room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms,

basements, and attached garages.

In addition, we recommend the following:

• Install a smoke detector inside every bedroom where a smoker sleeps.

• Install a smoke detector inside every bedroom where someone sleeps with the door partly or

completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside

may not wake up the sleeper if the door is closed.

• Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air

conditioners, or humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.

• Install smoke detectors in any room where an alarm control is located, or in any room where alarm

control connections to an AC source or phone lines are made. If detectors are not so located, a fire

within the room could prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR

TEMPORAL PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING

KITCHEN

BEDROOM

LIVING ROOM

✪

▲

BEDROOM

BDRM

DINING

LIVING ROOM

TV ROOM

KITCHEN

■

✪

✪✪

✪

▲

✪

BEDROOM

TO

BR

■

LVNG RM

BASEMENT

KTCHN

▲

.

CLOSED

DOOR

GARAGE

▲

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

Recommendations for Proper Intrusion Protection

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

commercial premises. This includes skylights and upper windows in a multi-level building.

In addition, we recommend that radio backup be used in a security system so that alarm signals can still be

sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are

normally sent over the phone lines, if connected to an alarm monitoring station).

www.PDF-Zoo.com

iv

Table of Contents

••••••••••••••••••••••••••••••••••••••••••••••••••

Conventions Used In This Manual............................................................................................................... viii

SECTION 1. Introduction...............................................................................................................................1–1

Description.......................................................................................................................................................1–1

Features............................................................................................................................................................1–1

SECTION 2. Installing the Control ..............................................................................................................2–1

Mounting the Cabinet .....................................................................................................................................2–1

Installing the Lock (if used)............................................................................................................................2–1

Mounting the Control's Circuit Board Alone in the Cabinet........................................................................2–2

Mounting Control and RF Receiver Circuit Boards Together in the Cabinet .............................................2–3

Standard Phone Line Connections.................................................................................................................2–4

Wiring the AC Transformer............................................................................................................................2–5

Installing the Backup Battery ........................................................................................................................2–6

Earth Ground Connections .............................................................................................................................2–6

SECTION 3. Installing Remote Keypads.....................................................................................................3–1

Keypads That May Be Used............................................................................................................................3–1

Wiring to the Keypads.....................................................................................................................................3–1

Mounting the Keypads....................................................................................................................................3–2

Supplementary Power for Additional Keypads .............................................................................................3–2

Preliminary Checkout Procedure ...................................................................................................................3–3

SECTION 4. Basic Hardwired Zones 1–6 ....................................................................................................4–1

Installing the Hardwired Zones......................................................................................................................4–1

Programming Hardwired Zones .....................................................................................................................4–4

Checkout Procedure for Hardwired Zones.....................................................................................................4–4

SECTION 5. Wired Zone Expansion.............................................................................................................5–1

Installing Zone Expansion Units....................................................................................................................5–1

Connections and Setup....................................................................................................................................5–1

Programming Wired Expansion Zones...........................................................................................................5–3

Checkout Procedure for Wired Expansion Zones ..........................................................................................5–3

SECTION 6. Wireless Expansion (5800 System)........................................................................................6–1

About Wireless Expansion ..............................................................................................................................6–1

Installing the 5881/5882 Receiver ..................................................................................................................6–2

Installing the 5800TM Module .......................................................................................................................6–3

Jam Detection and Reporting .........................................................................................................................6–3

About 5800 Series Transmitters.....................................................................................................................6–3

Installing 5800 Series Transmitters...............................................................................................................6–7

SECTION 7. Relay Outputs & Powerline Carrier Devices.....................................................................7–1

About Relays and Powerline Carrier Devices................................................................................................7–1

4204 and 4229 Relay Modules ........................................................................................................................7–1

Powerline Carrier Devices ..............................................................................................................................7–3

Programming Relay Outputs..........................................................................................................................7–4

SECTION 8. 4285 & 4286 VIP Module ..........................................................................................................8–1

About the 4285 & 4286 VIP (Voice Interactive Phone) Module....................................................................8–1

Installing the VIP Module...............................................................................................................................8–1

Programming the 4285/4286 VIP Module......................................................................................................8–4

Checking 4285/4286 VIP Module Operation..................................................................................................8–4

SECTION 9. External Sounders....................................................................................................................9–1

Compatible Sounders.......................................................................................................................................9–1

NFPA Requirements........................................................................................................................................9–1

Sounder Connections and Power....................................................................................................................9–2

Sounder Supervision .......................................................................................................................................9–2

Testing the Sounder ........................................................................................................................................9–2

www.PDF-Zoo.com

Table of Contents

v

SECTION 10. Long Range Radio ................................................................................................................10–1

About Long Range Radio...............................................................................................................................10–1

Wiring Connections .......................................................................................................................................10–1

Dynamic Signaling Feature..........................................................................................................................10–2

SECTION 11. Audio Alarm Verification (AAV) Unit ..............................................................................11–1

About Audio Alarm Verification ...................................................................................................................11–1

Wiring Connections .......................................................................................................................................11–1

SECTION 12. Final Power-Up .....................................................................................................................12–1

Earth Ground Connections ...........................................................................................................................12–1

AC Power-Up .................................................................................................................................................12–1

Connecting the Backup Battery....................................................................................................................12–1

Battery Tests..................................................................................................................................................12–2

SECTION 13. Mechanics of Programming ...............................................................................................13–1

About Programming ......................................................................................................................................13–1

Entering Program Mode................................................................................................................................13–2

Programming a Data Field............................................................................................................................13–2

Reviewing a Data Field/Erasing an Entry...................................................................................................13–2

Interactive Mode Programming (

✱

56,

✱

58,

✱

80,

✱

81, and

✱

82)................................................................13–2

Loading Factory Defaults..............................................................................................................................13–3

Programming System Setup Fields..............................................................................................................13–3

Exiting the Programming Mode ...................................................................................................................13–3

SECTION 14. Zone Response Type Definitions.......................................................................................14–1

Zone Type Definitions....................................................................................................................................14–1

SECTION 15. Data Field Descriptions.......................................................................................................15–1

Descriptions of System Data Fields..............................................................................................................15–1

SECTION 16. Zone Programming...............................................................................................................16–1

About Zone Programming.............................................................................................................................16–1

✱

56 Zone Programming Procedures.............................................................................................................16–1

✱

58 Expert Programming Mode Procedures ...............................................................................................16–4

To Remove a Zone..........................................................................................................................................16–6

To Delete and Replace a Transmitter Serial Number.................................................................................16–7

To Enter and Duplicate Wireless Keys ........................................................................................................16–7

SECTION 17. Output Device Programming.............................................................................................17–1

Programming Options Defined.....................................................................................................................17–1

Programming Output Relays and Powerline Carrier Devices....................................................................17–3

SECTION 18. Zone Lists................................................................................................................................18–1

About Zone List Menu Mode.........................................................................................................................18–1

Zone List Displays .........................................................................................................................................18–1

Cross Zoning - Zone List 04...........................................................................................................................18–2

NIGHT-STAY - Zone List 05.........................................................................................................................18–2

SECTION 19. Alpha Descriptor Programming........................................................................................19–1

About Alpha Descriptor Programming.........................................................................................................19–1

Zone Descriptors............................................................................................................................................19–1

Programming Zone Descriptors (Program Menu Mode

✴

82) .....................................................................19–1

Adding Custom Words/Numbers (not annunciated by the 4285/4286 VIP Module).................................19–3

SECTION 20. Remote Programming and Control (Downloading).....................................................20–1

About Remote Programming.........................................................................................................................20–1

Equipment Required .....................................................................................................................................20–1

Initial Download............................................................................................................................................20–2

Remote Programming Commands................................................................................................................20–2

Remote Programming Advisory Notes.........................................................................................................20–2

SECTION 21. System Communication.......................................................................................................21–1

Panel Communication with Central Station................................................................................................21–1

Report Code Formats.....................................................................................................................................21–1

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation & Setup Guide

vi

SECTION 22. System Operation .................................................................................................................22–1

Security Codes ...............................................................................................................................................22–1

Keypad Functions..........................................................................................................................................22–2

Setting the Real-Time Clock.........................................................................................................................22–6

SECTION 23. Testing the System ...............................................................................................................23–1

Test Procedure...............................................................................................................................................23–1

SECTION 24. Troubleshooting Guide........................................................................................................24–1

SECTION 25. Specifications & Accessories..............................................................................................25–1

Specifications .................................................................................................................................................25–1

Accessories (Compatible Devices).................................................................................................................25–3

APPENDIX A 5800 RF System Wireless Transmitters............................................................................A–1

Transmitter Input Loop Identification..........................................................................................................A–1

APPENDIX B Regulatory Agency Statements..........................................................................................B–1

APPENDIX C Warnings and Limitations ..................................................................................................C–1

Index.............................................................................................................................................................Index-1

Programming Form .................................................................................................................................... Insert

www.PDF-Zoo.com

vii

List of Figures

••••••••••••••••••••••••••••••••••••••••••••••••••

Figure 1. Installing the Cabinet Lock..................................................................................................................2–1

Figure 2. Mounting the PC Board........................................................................................................................2–2

Figure 3. Mounting the PC Board and RF Receiver Together in the Cabinet..................................................2–3

Figure 4. Telephone Line Connections................................................................................................................2–4

Figure 5. Connections of 4300 Transformer to the Control Board ....................................................................2–5

Figure 6. Keypad Connections to the Control Board..........................................................................................3–2

Figure 7. Using a Supplementary Power Supply for Keypads ..........................................................................3–3

Figure 8. 2-Wire Smoke Detector Connected to Zone 1......................................................................................4–2

Figure 9. 4-Wire Smoke Detector Connections (Zones 2–6)...............................................................................4–3

Figure 10. Wiring Connections - 4219 Expansion Module.................................................................................5–2

Figure 11. Wiring Connections - 4229 Expansion/Relay Module.......................................................................5–2

Figure 12. 5881/5882 RF Receiver (cover removed)............................................................................................6–2

Figure 13. 4229 Connections to Control..............................................................................................................7–2

Figure 14. 4204 Connections to Control..............................................................................................................7–3

Figure 15. 4300 Transformer Wiring Connections.............................................................................................7–4

Figure 16. 4285/4286 VIP Module Wiring Connections .....................................................................................8–3

Figure 17. Typical Sounder Wiring......................................................................................................................9–2

Figure 18. Bell Supervision Wiring .....................................................................................................................9–2

Figure 19. Long Range Radio Connections .......................................................................................................10–1

Figure 20. Connection of AAV Unit When Not Using a 4285/4286 VIP Module ............................................11–2

Figure 21. Connection of AAV Unit When Also Using a 4285 or 4286 VIP Module.......................................11–2

Figure 22. VISTA-15/VISTA-15CN Summary of Connections..................................................Inside Back Cover

www.PDF-Zoo.com

viii

Conventions Used In This Manual

••••••••••••••••••••••••••••••••••••••••••••••••••

Before you begin using this manual, it is important that you understand the meaning of the following

symbols:

U

L

A UL note that includes specific information that must be followed if you are installing this system

in a UL Listed application.

A note that includes specific information that must be followed if you are installing this system in a

Canadian UL Listed application..

A checked note includes information you should be aware of before continuing with the

installation, and which, if not observed, could result in operational difficulties.

This symbol warns of conditions that could seriously affect the operation of the system, or cause

damage to the system. Please read each warning carefully. This symbol also denotes warnings

about physical harm to the user.

Enter Zone Num.

(00 = Quit)

You may program many system options by responding to alpha keypad display

prompts. These prompts are shown in a double-line box.

✴

00

When programming the system, data fields are indicated by a “star” (

✴

) followed

by the data field number.

PRODUCT MODEL NUMBERS: Unless noted otherwise, references to specific model numbers represent

ADEMCO products.

www.PDF-Zoo.com

1–1

SECTION 1

Introduction

•••••••••••••••••••••••••••••••••••••••••••••••••

In This Section

♦

Description

♦

Features

•••••••••••••••••••••••••••••••••••••••••••••••••

Description

The VISTA-15/VISTA-15CN is a security system control that supports up to 32 zones,

including six basic hardwired zones (1 through 6) and a maximum of 26 expansion zones.

These expansion zones may include up to eight hardwired zones, or up to 26 wireless zones if

hardwired zones are not used. Three separate keypad-activated zones are also provided.

Features

Basic Hardwired Zones

Provides 6 basic hardwired zones having the following characteristics:

• EOLR supervision

supporting

N.O. or N.C. sensors

• Programmable response time (10, 350, or 700 milliseconds)

• Up to sixteen 2-wire smoke detectors on zone 1

• 4-wire smoke or heat detectors on zones 2 through 6 (as many as can be powered from

Auxiliary Power on the control).

Optional Expansion Zones (26 total: up to 8 wired with 18 wireless, OR 26 wireless)

Wired Expansion

:

Supports up to 8 additional wired zones using a 4219 Expansion Module or 4229

Expansion/Relay Module. These zones have the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• 300-500mSec normal response with an option for fast (10-15mSec) response on loop A (first

expansion zone).

Wireless Expansion:

Supports up to 26

wireless

zones (fewer if using wired expansion zones).

• Requires the use of a

5881 (5882 in Canada)

type RF receiver,

as indicated below:

Receiver Model No. of Zones

5881L/5882L Up to 8

5881M/5882M Up to 16

5881H/5882H Up to 26

• Requires the use of 5800 Series Wireless Transmitters.

Remote Keypads

Up to 4 of any of the following keypads may be used in the installation:

Fixed-word keypad: 6128, 6128RF

Alpha keypad: 6139 (2-line alphanumeric display)

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation and Setup Guide

1–2

Security Codes Supported

• One Installer code for entire system (user 1)

•One Master code

for entire system

(user 2)

• 12 Secondary User

codes

(users 3–14)

• One Temporary code (user 15)

• One Duress code (user 16).

Temporary Code: A special code that can be used to disarm and arm the system until the Master

code is entered.

Duress Code: An emergency code that, when entered by

any

user to disarm or arm the system,

sends a silent duress message to the Central Station.

Keypad Panic Features

• Up to 3 programmable panic key functions provided

• Designated as zones 95, 96, 99

• Activated by wired and wireless keypads

• Distinguished by subscriber ID number.

Zone Monitor Features

• Provides automatic high loop resistance detection on hardwired zones 2–6, and displays a

CHECK

message for the affected zone when the system is in the disarmed state.

• Contains a Hardwire Short Detection circuit for zones 1-6

†

, and enabled in

✱30.

Detecting a

short in any wired zone, it sends a sensor Trouble message to the Central Station when the

system is in the disarmed state. At the same time a

CHECK

message is displayed on the

keypad.

†

Hardwire Short Detection is disabled on any zone programmed for FIRE (Zone type 09).

Either condition (high resistance or short) detected on any zone, prevents the system from

being armed until the offending condition is cleared. Conversely, when the system is armed,

and these conditions occur, an alarm is generated.

Exit Error False Alarm Prevention Features

• Enables the system to determine the difference between an actual alarm and an alarm

caused by leaving an entry/exit or interior zone open after the Exit Delay expires. If not

disarmed in time, an alarm sounds and an Exit Error report is sent to the Central Station.

An exit alarm condition also occurs if an entry/exit or interior zone re-opens within 2

minutes after the end of an Exit Delay.

•

The system provides an automatic Exit Delay Reset feature that allows the user to exit

(fault), close the door (restore the fault), then re-enter (fault again) the premises within the

exit delay time period. Upon re-entering, a new exit delay time period is begun with the

keypad annunciating three rapid beeps. This feature only resets the exit delay time once

for each arming session.

Optional Output Relays and Powerline Carrier Devices (X10 type)

The VISTA-15/VISTA-15CN

supports the following optional output relays and Powerline

Carrier devices (X10 type):

• Maximum of 4 output devices

• Up to 4 relays using one

4204

Relay Module

• Up to 2 relays using one

4229

Zone/Relay Module

• Up to 4 Powerline Carrier devices (you must subtract the number of relay outputs actually

used by the 4204 or 4229 modules, if used).

Actions are programmable to respond to zone activity or manual keypad entries.

Powerline Carrier devices require the use of the optional 4300 Transformer Module instead of the

supplied 1321/1321CN AC Transformer.

www.PDF-Zoo.com

Section 1 - Introduction

1–3

Optional VIP Module

The VISTA-15/VISTA-15CN supports the ADEMCO 4285/4286 VIP Module (refer to

Section 8: 4285/4286 VIP Module for further information).

Provides access to the system via on-premises or off-premises phones for arming, disarming,

etc., plus control of relay outputs and Powerline Carrier devices.

Paging Feature

If programmed, the paging feature allows certain system conditions to be reported to a pager.

Up to 16 digits may be programmed to be sent as a message to the pager. A 7-digit code

following the programmed message indicates the type of condition that has occurred.

Audio Alarm Verification (AAV) Option

Provides a programmable Audio Alarm Verification (AAV) option, which can be used in

conjunction with an output relay to permit voice dialog between an operator at the Central

Station and a person at the premises.

This AAV option must be used with a relay unit, such as an Eagle Model 1250.

U

L

The AAV option may not be used in UL installations.

Optional Long Range Radio

Allows all messages that have been programmed to go to the primary telephone number to

also be sent to any ECP-operational

ra

dio (such as the 7835C, 7720PLUS, and 7820) for

transmission to the Central Station.

Built-in Telephone Line Monitoring Option

You can monitor telephone line voltage to supervise the phone line connection. You must

connect the panel to a proper earth ground or you will get a false line cut indication if this

feature is enabled.

The loss of the line can optionally cause a local display, or a display and trouble sound.

Event Logging

Keeps a record of up to 48 selected events in a history log. All control and readout from the

log is done via ADEMCO COMPASS software

only

.

Quick Arm Feature

Quick Arm may be programmed , allowing use of the [#] key in place of the security code for

arming (Quick Arm will not work unless the Master code has been programmed into the

system).

Alarm Output Features

•

Provides a 12VDC, 2

amp

output that can drive the compatible sounders listed in

Section 9:

External Sounders

(assuming a fully charged battery is connected).

• Steady output for burglary/panic, or

temporal

pulse output (3 pulses – pause – 3 pulses –

pause – 3 pulses . . .) for fire.

• Uses

current

-limiting circuitry for protection.

• Provision for Bell supervision.

Optional Bell Supervision

Red jumper on control board, when cut, provides supervision of bell wiring (when bell is

wired with EOL resistor, as indicated in the instructions).

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation and Setup Guide

1–4

Chime/Chime by Zone

Chime, when on, normally sounds when any entry/exit or perimeter zone is faulted. However,

a “chime by zone” option, when programmed, allows only specific zones to chime if they are

faulted when the system is in the chime mode.

Auxiliary Power Output Features

• Provides 12VDC, 600mA maximum (500mA maximum for UL installations). Uses current-

limiting circuitry for protection.

• Interrupts for smoke detector reset if 4-wire smoke detectors are used.

Programming

Programmed options are stored in electrically erasable, nonvolatile EEPROM memory

(information can be reprogrammed at any time and will not be lost in the event of a power

loss).

The system can be uploaded, downloaded, or controlled via an IBM-compatible computer,

COMPASS software, and a

modem specified by ADEMCO.

Keypad programming consists of:

• Data field programming

• Interactive (menu) mode programming.

To program from a keypad, you must connect a 6139 2-line alpha keypad, but it need not stay in

the system.

Communication Formats Supported

•

ADEMCO Low Speed

(Standard or Expanded)

•

Sescoa/

Radionics (Standard or Expanded)

•

ADEMCO

Express

•ADEMCO

Contact ID

Zone Descriptors

You can assign

alpha descriptors to all zones (only when using alpha keypads).

AC Power Supply

Uses

1321/1321CN

, 110VAC plug-in transformer with 16.5VAC, 25VA output, unless

Powerline Carrier devices

(for example,

X10 type) are used, in which case a 4300

Transformer Module

must be used.

Backup Battery

Rechargeable (Sealed Lead Acid) 12VDC, 4AH-17.2AH. Refer to

Section 12: Final Power-

Up

to calculate the actual battery size needed.

www.PDF-Zoo.com

2–1

SECTION 2

Installing the Control

••••••••••••••••••••••••••••••••••••••••••••••••••

In This Section

♦

Mounting the Cabinet

♦

Installing the Lock

♦

Mounting the Control's Circuit Board Alone in

the Cabinet

♦

Mounting the Control and RF Receiver Circuit

Boards Together

♦

Standard Phone Line Connections

♦

Wiring the AC Transformer

♦

Installing the Backup Battery

♦

Earth Ground Connections

••••••••••••••••••••••••••••••••••••••••••••••••••

Mounting the Cabinet

Use fasteners or anchors (not supplied) to mount the control cabinet to a sturdy wall in a

clean, dry area that is not readily accessible to the general public. Four mounting holes are

provided at the back of the cabinet.

If an RF receiver is being used and you intend to mount its PC board within the cabinet, note

the following:

• Do not mount the cabinet on or near metal objects. This decreases RF range and/or block

RF transmissions from wireless transmitters.

• Do not locate the cabinet in an area of high RF interference (revealed by frequent or

prolonged lighting of the LED in the receiver after it is operational (random flicker is OK).

Installing the Lock (if used)

Use an ADEMCO No. N6277 Cam Lock and No. N6277–1 Push-On Clip (Retainer Clip).

NOTE:

The cabinet can be closed and secured without a lock by using 2 screws in the cover's

edge.

To install the lock, perform the following steps:

1. Remove the cabinet door. It is easily

removed for servicing and is easily re-

installed.

2. Remove the lock knockout from the

control cabinet door. Insert the key into

the lock. Position the lock in the hole,

making certain that the latch will make

contact with the latch bracket when the

door is closed.

3. Hold the lock steady and insert the

retainer clip into the retainer slots.

Position the clip as illustrated in order to

permit easy removal.

CABINET DOOR BOTTOM

RETAINER

CLIP

RETAINER CLIP

(NOTE POSITION)

RETAINER

SLOTS

LOCKED

UNLOCKED

Figure 1. Installing the Cabinet Lock

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation and Setup Guide

2–2

Before installing the cabinet's contents, remove the metal cabinet knockouts required for wiring

entry. Do not attempt to remove the knockouts after the circuit board has been installed.

Mounting the Control's Circuit Board Alone in the Cabinet

To mount the circuit board alone in the cabinet, follow these steps:

1. Hang two short

mounting

clips (provided) on the raised cabinet tabs (see Detail B in

Figure 2).

2. Insert the top of the circuit board into the slots at the top of the cabinet. Make sure that

the board rests on the correct row (see Detail A).

3. Swing the base of the board into the mounting clips and secure the board to the cabinet

with the accompanying screws (see Detail B).

CABINET

+

CIRCUIT BOARD

CABINET

DETAIL B

SIDE VIEW

OF MOUNTING

CLIPS

DETAIL A

SIDE VIEW

OF BOARD

SUPPORTING

SLOTS

CIRCUIT

BOARD

V15-01-V0

Figure 2. Mounting the PC Board

www.PDF-Zoo.com

Section 2 - Installing the Control

2–3

Mounting Control and RF Receiver Circuit Boards Together in the Cabinet

To mount the control and RF receiver boards together in the cabinet, do the following:

1.

Hang two short (black) mounting clips (provided with receiver) on the raised cabinet tabs,

as shown in Detail B in Figure 3

.

2.

Insert the top of the receiver board (removed from its own case as described in its

instructions) into the slots at the top of the cabinet, as shown in Detail A in Figure 3

.

Make sure that the board rests on the correct row of tabs, as shown.

3.

Swing the base of the board into the mounting clips and secure it to the cabinet with the

accompanying screws (see Detail B).

4.

Insert the top of the control's board into the slot in the clips and position two long (red)

clips at the lower edge of the board (see Detail C).

5.

Swing this board into place and secure it with two additional screws.

6.

Insert grounding lugs (supplied with the receiver) through the top of the cabinet into the

left-hand terminals of the antenna blocks (at the upper edge of the receiver board). Secure

the grounding lugs to the cabinet top with the screws provided, as shown in Detail D.

7.

Insert the receiver's antennas through the top of the cabinet, into the blocks' right-hand

terminals, and tighten the screws.

8.

Refer to

Section 6: Wireless Expansion (5800 System)

for receiver setup and wiring

instructions.

MOUNTING

CLIP

CABINET

DETAIL D

ANTENNA AND GROUNDING LUG INSTALLATION

ANTENNA

MOUNT

(2 PLACES)

ANTENNA

(2)

SCREW

(2)

MOUNTING

CLIP

CONTROL

CIRCUIT

BOARD

SUPPORTING

SLOTS

HOLES FOR ANTENNAS

AND GROUNDING LUGS

RECEIVER CIRCUIT BOARD

(See Detail D)

++

RCVR BRD

DETAIL A

SIDE VIEW

OF BOARD

SUPPORTING SLOTS

DETAIL B

SIDE VIEW

OF MOUNTING

CLIP

DETAIL C

SIDE VIEW

OF MOUNTING

CLIP

GROUNDING

LUG

(2)

V15-02-V0

CIRCUIT BOARD

CABINET

Figure 3. Mounting the PC Board and RF Receiver Together in the Cabinet

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation and Setup Guide

2–4

Standard Phone Line Connections

The wiring connections shown here are not applicable if the 4285/4286 VIP Module is used. Refer

to

Section 8: 4285/4286 VIP Module

for information regarding phone line connections, which are

different than those shown here.

Connect incoming phone line and handset wiring to the main terminal block via an RJ31X

jack (CA38A jack in Canada) as follows and as shown in Figure 4.

Term. 21: Local Handset (TIP – Brown*)

Term. 22: Local Handset (RING – Gray*)

Term. 23: Incoming Phone Line (TIP – Green*)

Term. 24: Incoming Phone Line (RING – Red*)

* Colors of wires in Direct Connect Cord.

TERMINALS

ON CONTROL

EARTH GROUND

INCOMING TELECOM LINE

Handset

TIP

RING

RJ31X JACK

(CA38A in

CANADA)

PLUG

DIRECT

CONNECT

CORD

TIP

RING

GROUND

PREMISES

PHONES

{

BROWN (TIP)

GREY (RING)

GREEN (TIP)

RED (RING)

21 22 23 24 25

Incoming

Telecom Line

IMPORTANT!

IF THE PANEL IS NOT CONNECTED TO A

PROPER EARTH GROUND, YOU MAY GET

FALSE TELEPHONE LINE CUT INDICATIONS

(IF THE TELEPHONE LINE MONITOR HAS

BEEN PROGRAMMED IN FIELD 92).

Figure 4. Telephone Line Connections

www.PDF-Zoo.com

Section 2 - Installing the Control

2–5

Wiring the AC Transformer

1321/1321CN Transformer

Wire the 1321/1321CN Transformer to terminals 1 and 2 on the control board. See wiring

table below to determine wire gauge.

Use caution

when wiring the transformer to the control panel to guard against blowing the

fuse inside the transformer (the fuse is nonreplaceable).

4300 Transformer

If you are going to use a

4300 Transformer

Interface (required if Powerline Carrier devices

are used), connect the 4300 Transformer’s terminals as follows:

1.

Connect terminals

1, 3 (AC), and 2 (Ground) to control board terminals 1, 2, and 25,

respectively (see

Figure 5

). See

table

below to determine wire gauge to use.

WIRING TABLE

Distance of Transformer

From the Control Panel

Wire Gauge

to Use

Up to 50 feet # 20

50-100 feet # 18

100-250 feet # 16

Wiring to the AC transformer must not exceed 250 feet using 16-gauge wire. The voltage reading

between terminals 1 and 2 of the control must not fall below 16.5VAC, or an

AC LOSS

message is

displayed.

Do not plug the transformer into the AC outlet until you are instructed to do so later in the manual.

2.

Wire the other three terminals (Sync, Data, Com) on the 4300 Transformer. Wires from

these terminals must be connected to a 9-pin connector on the control board (using a

4142TR Cable

supplied with the 4300 Transformer), as shown in

Figure 5

. These

particular wires can be 24-gauge or larger, and can be run along with the AC and ground

wires to the control panel.

123456789

9-PIN CONNECTOR

ON CONTROL BOARD

BLACK

BLUE

BROWN

GREEN

RED

WHITE

YELLOW

GRAY

VIOLET

4142TR CABLE

1

2

3

4

56

125 2

AC

Earth

Ground

AC

Sync

Data

Com

4300 TRANSFORMER/INTERFACE

TERMINALS

ON CONTROL

BOARD

Figure 5. Connections of 4300 Transformer to the Control Board

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation and Setup Guide

2–6

Installing the Backup Battery

If necessary, refer to Section 12: Final Power-Up for information regarding battery size to

use.

Do not attach the connector cable to the battery terminals until you are instructed to do so later in

the manual.

Install the backup battery as follows:

1. Place the 12-volt backup battery in the control cabinet.

2. Attach red and black wires on the battery connector cable as follows:

a. Red to the positive (

+

) battery terminal

on the control board

(see

Figure 22.

VISTA-15/VISTA-15CN Summary of Connections

for location, if necessary).

b. Black to the negative (

–

) battery terminal

on the control board.

U

L

Use a 4AH battery or larger for UL installations. Refer to

Section 12: Final Power-Up

to calculate

the actual battery size needed.

Earth Ground Connections

The designated earth ground terminal (25) must be terminated in a good earth ground for

the lightning transient protective devices in this product to be effective. The following are

examples of good earth grounds available at most installations:

Metal Cold Water Pipe:

Use a noncorrosive metal strap (copper is recommended) firmly

secured to the pipe to which the ground lead is electrically connected and secured.

AC Power Outlet Ground:

Available from 3-prong, 120VAC, power outlets only. To test the

integrity of the ground terminal, use a 3-wire circuit tester with neon lamp indicators, such

as the

UL

Listed

Ideal Model 61-035

, or equivalent, available at most electrical supply stores.

www.PDF-Zoo.com

3–1

SECTION 3

Installing Remote Keypads

••••••••••••••••••••••••••••••••••••••••••••••••••

In This Section

♦

Keypads That May Be Used

♦

Wiring to the Keypads

♦

Mounting the Keypads

♦

Supplementary Power for Additional Keypads

♦

Preliminary Checkout Procedure

••••••••••••••••••••••••••••••••••••••••••••••••••

Keypads That May Be Used

Up to 4 keypads may be used in the system, independent of auxiliary power considerations

(you may need to use an auxiliary power supply if the 600mA aux. output is exceeded).

The following keypad models may be used:

• Fixed-Word Display: 6128, 6128RF

•Alpha

Display

:

6139.

Be sure the keypads are set to the non-addressable mode (address 31).

Wiring to the Keypads

To wire keypads to the control, perform the following steps:

1. Determine wire gauge by referring to the

Wiring Run Chart

below.

For devices (keypads, RF receivers, zone expander, etc.) connected to a single 4-wire run,

determine the current drawn by all units connected to the single wire run, then refer to

the Wiring Run Chart below to determine the maximum wire length that can be safely

used for each wire size. Current draw for all devices can be found in Section 25:

Specifications & Accessories

.

NOTE: Refer to Table 1. AUXILIARY DEVICE CURRENT DRAW WORKSHEET in

Section 12: Final Power-Up to obtain the current draw for all keypads.

Maximum wire lengths for any device that is home run to the control can also be determined from

the Wiring Run Chart, based on the current draw of that device alone.

Wiring Run Chart for Devices* Drawing Aux Power

from the Control (12V+ & 12V–)

TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN

Wire

Size

50mA or less 100mA 300mA 500mA 600mA

#22 500 ft (152m) 250 ft (76m) 80 ft (24m) 50 ft (15m) 42 ft (13m)

#20 750 ft (228.6m) 380 ft (116m) 130 ft (39.6m) 80 ft (24m) 67 ft (20.4m)

#18 1300 ft (396m) 650 ft (198m) 220 ft (67m) 130 ft (39.6m) 115 ft (35m)

#16 1500 ft (457m) 1000 ft (305m) 330 ft (100.5m) 200 ft (70m) 170 ft (52m)

* Includes Keypads, RF Receivers, Zone Expander/Relay Units, or 4285/4286 VIP Module.

www.PDF-Zoo.com

VISTA-15/VISTA-15CN Installation and Setup Guide

3–2

The length of all wire runs must not exceed 1500 feet (457m) when unshielded quad conductor

cable is used (750 feet if shielded cable is used). This restriction is due to the capacitive effect on

the data lines when quad cable is used.

2. Run field wiring from the control to the keypads (using standard 4-conductor twisted wire

cable of the wire gauge determined in step 1).

3.

Connect

remote

keypads

to terminals 4, 5, 6, and 7 on the control board, as shown in

Figure 6.

5

6

7

4

TERMINALS ON

CONTROL PANEL

BLACK

RED

GREEN

YELLOW

KEYPAD

Figure 6. Keypad Connections to the Control Board

Mounting the Keypads

To mount the keypads, perform the following steps:

1. Make sure the

addressable keypad(s)

are set to non-addressable mode (address 31), which

is the factory default setting. Refer to the instructions provided with the keypad for

address setting procedure.

2. Mount the keypads at a height that is convenient for the user. Refer to the instructions

provided with the keypad for mounting procedure.

You can either surface mount or flush mount keypads (using an appropriate Trim Ring

Kit:

6139TRK

). Refer to the mounting instructions and template included with the keypad

and/or trim ring kit for specific information.

Supplementary Power for Additional Keypads

The VISTA-15/VISTA-15CN control provides 600mA for powering keypads (up to 4) and

other devices from the auxiliary power output. The backup battery supplies power to these

keypads in the event that AC power is lost.

When the

control’s

auxiliary power load for all devices exceeds 600mA, you can power

additional keypads from a regulated 12VDC power supply (e.g.,

487-12

supplies 12V, 250mA;

488-12

supplies 12V, 500mA). Use a

UL

Listed, battery-backed supply for UL installations.

The 487-12/488-12

power

supplies have a backup battery that can power these keypads in the

event of AC power loss to the main supply.

Keypads powered from supplies that do not have a backup battery

will not function

when AC

power is lost. Therefore, be sure to power at least one keypad from the control's auxiliary power

output.

Connect the additional keypads as shown in

Figure 7

, using the keypad wire colors shown. Be

sure to observe the current ratings for the power supply used.

www.PDF-Zoo.com

La pagina sta caricando ...

ADEMCO Security System VISTA-15 Guida d'installazione

Questo manuale è adatto anche per

ADEMCO Security System VISTA-15 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti