Sub-Zero 5310845 Guida d'installazione

WINE STORAGE

INSTALLATION GUIDE

SPECIFICATIONS, INSTALLATION, AND MORE

WINE STORAGE

Contents

3 Wine Storage

4 Model UW-24 | UW-24FS Site Preparation

6 Model UW-24 | UW-24FS Installation

10 Model BW-30 Site Preparation

16 Model BW-30 Installation

Features and specications are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

2

|

Sub-Zero Customer Care 800.222.7820

subzero.com

|

3

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. The

rating plate is located on the underside of the control panel,

on the left. Refer to the illustrations below.

If service is necessary, contact Sub-Zero Factory Certied

Service with the model and serial number. For the name

of the nearest Sub-Zero Factory Certied Service or for

questions regarding the installation, visit the contact

and support section of our website, subzero.com, or call

Sub-Zero Customer Care at 800-222-7820.

WINE STORAGE

Tools and Materials

• Screwdrivers—standard, Phillips, and Torx.

• Power drill.

• Drill bits (masonry bits required for concrete installation).

• Standard socket and wrench set.

• 2' and 4' levels.

• Material to protect home, ooring, and cabinetry during

installation.

Model UW-24 and UW-24FS

Model BW-30

RATING PLATE

4

|

Sub-Zero Customer Care 800.222.7820

W

OPENING WIDTH

34

1

/

2

"

(876)

OPENING

HEIGHT

TOP VIEW

SIDE

VIEW FRONT VIEW

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

3

/4" (19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/2" (89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

24" (610)

OPENING

DEPTH

Opening Dimensions

MODEL UW-24

MODEL UW-24 | UW-24FS SITE PREPARATION

OPENING WIDTH

W

UW-24 24" (610)

DUAL OPENING WIDTH

W

Two 24" (610) Models 48

1

/8" (1222)

Dual installation kit required.

DUAL INSTALLATION

If two units are installed side by side, a dual installation kit

may be required. Installations without a custom ller strip

require a dual installation kit. If a dual installation kit is not

specied, a 2"

(51) ller strip is recommended between the

units. Dual installations without a ller strip can only be

accomplished using two units with opposite hinges. Refer to

the illustrations below.

Dual installation kits are available through an authorized

Sub-Zero dealer. For local dealer information, visit the nd

a showroom section of our website, subzero.com. For

questions regarding the installation, call Sub-Zero Customer

Care at 800-222-7820.

WITHOUT FILLER STRIP

FILLER STRIP

Opposite hinges

Same side hinges

subzero.com

|

5

Electrical Requirements

Installation must comply with all applicable electrical codes.

The electrical supply should be located within the shaded

area shown in the illustration below. A separate circuit ser-

vicing only this appliance is required. A ground fault circuit

interrupter (GFCI) is not recommended and may cause inter-

ruption of operation.

IMPORTANT NOTE: The electrical outlet must be placed so

the grounding prong is to the right of the thinner blades.

The outlet must be ush with the back wall.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp dedicated circuit

Receptacle 3-prong grounding-type

WARNING

Do not use an extension cord, two-prong adapter, or

remove the power cord ground prong.

Preparation

To operate properly, the door must open a minimum of 90°.

Use a minimum 3"

(76) ller in corner installations to assure

a 90° door opening.

Uncrate the unit and inspect for damage. Remove and

recycle packing materials. Do not discard the kickplate, anti-

tip bracket, hardware, and the leveling legs which hold the

wood base to the bottom of the unit.

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

bracket must be installed.

MODEL UW-24

The anti-tip bracket should be attached to the wall behind

the unit with the bracket ange located

1

/4" (6) above the top

of the unit. Refer to the illustration below. Failure to properly

position the anti-tip bracket will prevent proper engagement.

For installations that cannot accommodate the anti-tip

bracket, a countertop bracket is provided to secure the unit

to the countertop. Refer to the illustration below.

MODEL UW-24 | UW-24FS SITE PREPARATION

3" (76)

15

1

/2"

(394)

2"

(51)

LEFT SIDE

OF OPENING

FLOOR

Electrical supply location

1

/4" (6)

ANTI-TIP

BRACKET

COUNTERTOP

BRACKET

Anti-tip bracket (UW-24)

Countertop bracket

6

|

Sub-Zero Customer Care 800.222.7820

Anti-Tip Bracket

MODEL UW-24FS

The back of the anti-tip bracket must be installed 24

5

/8"

(625)

from the front and centered behind the unit. Refer to

the illustration below. Refer to page 16 for wood and con-

crete oor applications.

MODEL UW-24 | UW-24FS INSTALLATION

ANTI-TIP BRACKET

Anti-tip bracket (UW-24FS)

Custom Panel

MODEL UW-24

For overlay applications, a custom door panel must be

installed. Panel size is critical for a proper t. To verify the

panel requirements and dimensions, refer to the Sub-Zero

Design Guide at subzero.com/specs.

Finish all sides of the custom panel. They may be visible

when the door is open or through the glass door.

The custom overlay door panel is attached using the screws

provided, through the door frame. The screw locations are

marked on the back of the custom panel using tenon cen-

ters inserted into the holes of the door frame.

With the unit secured and door closed, hold the custom

panel in the desired position on the door. Lightly tap the

front of the panel to locate the mounting positions. Remove

the tenon centers. Refer to the illustration below.

The door frame has mounting holes to accommodate

Sub-Zero accessory handles. If the handle mounting holes

are not used, the handle should be attached to the custom

panel prior to mounting. The screw heads may need to be

countersunk into the panel for proper alignment.

To mount the custom panel, open the door and use the pre-

drilled holes to position the panel. Drive the screws into the

panel through the black tape on the door frame. The screw

holes are hidden behind the door gasket. Use as many

screws as necessary to secure the custom panel. Refer to

the illustration below.

GASKET

GLASS

13

/32" (11)

DIAMETER

1

/4" (6)

DIAMETER

Tenon center

Door frame cross section

DOOR

FRAMEPANEL

TENON CENTER

subzero.com

|

7

MODEL UW-24 | UW-24FS INSTALLATION

Custom Panel

Adjustments can be made to the custom panel with a few

mounting screws in place, but not fully tightened. Once the

proper position is achieved, install and secure all screws.

Cover the holes on the inside of the door frame with the

cover patches or plugs provided.

CAUTION

A solid panel cannot be installed over the glass door. A

solid door is available through an authorized Sub-Zero

dealer. For local dealer information, visit the nd a

showroom section of our website, subzero.com.

Placement

CAUTION

Before moving the unit into position, secure the door

closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

If the unit will be connected to a home security system,

run lead wires through the compressor compartment prior

to positioning the unit. Refer to page 8. Once the unit is in

position, the wiring connections can be completed from the

front.

Leveling

Level the unit before sliding it into position. Turn each of the

four leveling legs clockwise to raise the unit and counter-

clockwise to lower. Refer to the illustration below.

LEVELING LEGS

Leveling

8

|

Sub-Zero Customer Care 800.222.7820

MODEL UW-24 | UW-24FS INSTALLATION

Completion

Plug the power cord into the grounded outlet, then slide

the unit into position. Verify the anti-tip bracket is properly

engaged.

It may be necessary to install the unit

1

/4" (6) beyond the

front surface of adjacent cabinetry to prevent interference

when the door is opened to 145°. Refer to the full-scale

template on page 9.

HOME SECURITY CONNECTION

If the unit will be connected to a home security system,

make connections to the leads shown in the illustration

below. Refer to the following color codes:

• Normally open contacts—white with red stripe wire.

• Normally closed contacts—white with blue stripe wire.

• Common—gray with white stripe wire.

Use the spade terminals or wire nuts provided to make

proper wiring connections.

CAUTION

The alarm circuit in the unit is intended as a low-

voltage, low-current device only. It should not be used

to switch line power. Any unused terminals should be

completely insulated and all wires should be secured

away from conductive or moving components.

ANCHORING

To anchor, use the countertop bracket provided to secure

the unit to the underside of the countertop. Refer to the

illustration below. If the countertop bracket cannot be

used, install shims along the top and sides of the unit.

KICKPLATE INSTALLATION

Install the kickplate using the two screws provided. Refer

to the illustration below. The kickplate must be removable

for service. The oor cannot interfere with removal. Do not

cover the louvered section of the kickplate.

COUNTERTOP

BRACKET

KICKPLATE

Anchoring

Kickplate installation

HOME SECURITY

LEADS

Home security connection

subzero.com

|

9

MODEL UW-24 | UW-24FS INSTALLATION

DOOR CLOSED

UNDERCOUNTER

UNIT

ADJACENT

CABINETRY

3

/4" (19) DOOR PANEL

1

/2"

(13)

1

/8" (3)

1

/4"

(6)

HINGE AT 145°

OPENING

(DOOR OPENS PAST 145°)

1" (25)0"

SCALE

145° door opening (top view)

Door Clearance

FULL-SCALE TEMPLATE

To allow for a 145° door opening, the unit should extend

a minimum of

1

/4" (6) beyond the front surface of adjacent

cabinetry. The unit can be installed ush, however, there

is potential for interference with the panel if the door is

opened past 90°.

10

|

Sub-Zero Customer Care 800.222.7820

Opening Dimensions

STANDARD INSTALLATION

MODEL BW-30 SITE PREPARATION

If two units are installed side by side, refer to page 12.

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit

.

83

3

/4"

(2127)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

FRONT VIEW

SIDE

VIEW

TOP VIEW

W

OPENING WIDTH

3

/

4

"

(19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/2" (89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

OPENING WIDTH

W

BW-30 29

1

/2" (749)

subzero.com

|

11

Opening Dimensions

FLUSH INSET INSTALLATION

MODEL BW-30 SITE PREPARATION

Dimensions assume a

3

/4" (19) panel thickness. If two units

are installed side by side, refer to page 13.

FLUSH INSET WIDTH

W

BW-30 32" (813)

84"

(2134)

FLUSH

INSET

HEIGHT

1

/4"

(6)

26

3

/16"

(665)

FLUSH

INSET

DEPTH

2

3

/16"

(56)

FRONT VIEW

SIDE

VIEW

TOP VIEW

1

/4"

(32)

W

FLUSH INSET WIDTH

FINISHED

CLEATS

NOTE: 3

1

/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit with

3

/4" (19) panel.

5

11

/16"

(145)

FINISHED

RETURN

FILLER

FRAMED

CABINETRY

W

CLEAT

3

/4" (19)

TYPICAL

3

1

/2"

(89)

5

11

/

16

"

(145)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

1

/2"

(89)

CLEAT

3

/4" (19)

TYPICAL

12

|

Sub-Zero Customer Care 800.222.7820

Opening Dimensions

DUAL STANDARD INSTALLATION

MODEL BW-30 SITE PREPARATION

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit

.

83

3

/4"

(2127)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

FRONT VIEW

SIDE

VIEW

TOP VIEW

W

OPENING WIDTH

3

/

4

"

(19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/

2

"

(89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

DUAL OPENING WIDTH

W

BW-30 and 30" Built-In Model 59

3

/4" (1518)

BW-30 and 36" Built-In Model 65

3

/4" (1670)

A dual installation kit is required for this installation.

subzero.com

|

13

Opening Dimensions

DUAL FLUSH INSET INSTALLATION

MODEL BW-30 SITE PREPARATION

84"

(2134)

FLUSH

INSET

HEIGHT

1

/4"

(6)

26

3

/16"

(665)

FLUSH

INSET

DEPTH

2

3

/16"

(56)

FRONT VIEW

SIDE

VIEW

TOP VIEW

FINISHED

CLEATS

1

/4"

(32)

W

FLUSH INSET WIDTH

NOTE:

3

1

/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit with

3

/4" (19) panel.

5

11

/16"

(145)

FINISHED

RETURN

FILLER

FRAMED

CABINETRY

W

CLEAT

3

/4" (19)

TYPICAL

3

1

/2"

(89)

5

11

/

16

"

(145)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

1

/2"

(89)

CLEAT

3

/4" (19)

TYPICAL

DUAL FLUSH INSET WIDTH

W

BW-30 and 30" Built-In Model 62

1

/4" (1581)

BW-30 and 36" Built-In Model 68

1

/4" (1734)

Dimensions assume a

3

/4" (19) panel thickness. A dual instal-

lation kit is required for this installation.

14

|

Sub-Zero Customer Care 800.222.7820

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply should be located within the shaded

area shown in the illustration below. A separate circuit ser-

vicing only this appliance is required. A ground fault circuit

interrupter (GFCI) is not recommended and may cause inter-

ruption of operation.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

CAUTION

The outlet must be checked by a qualied electrician

to be sure it is wired with the correct polarity. Verify the

outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter, or

remove the power cord ground prong.

Dual Installation

If two units are installed side by side, a dual installation kit

may be required. Installations without a custom ller strip

require a dual installation kit. If a dual installation kit is not

specied, a 2"

(51) ller strip is recommended between units.

Dual installations without a ller strip can only be accom-

plished using two units with opposite hinges. Refer to the

illustrations below.

Dual installation kits are available through an authorized

Sub-Zero dealer. For local dealer information, visit the nd a

showroom section of our website, subzero.com. For ques-

tions regarding the installation, call Sub-Zero Customer

Care at 800-222-7820.

WITHOUT FILLER STRIP

FILLER STRIP

Opposite hinges

Same side hinges

MODEL BW-30 SITE PREPARATION

75

1

/2" (1918)

FROM FLOOR

7"

(178)

E

6"

(152)

RIGHT SIDE

OF OPENING

Electrical supply location

subzero.com

|

15

Preparation

Uncrate the unit and inspect for damage. Remove the wood

base and discard the shipping bolts and brackets. Remove

and recycle packing materials. Do not discard the kickplate,

anti-tip brackets, and hardware.

Completely retract the front leveling legs to allow the unit to

be moved into position. The front and rear leveling legs can

be adjusted from the front once the unit is in position.

Remove the drain pan to avoid damage and allow for proper

appliance dolly placement.

The grille assembly should be removed prior to moving the

unit. To remove, pull out on the bottom edge of the grille and

rotate upward. Loosen the two back grille mounting screws

and remove the two front grille mounting screws. With the

grille held rmly, pull forward to remove. Refer to the illustra-

tions below.

FRONT

GRILLE SCREW

BACK GRILLE

SCREW

GRILLE

ADJUSTMENT

SCREWS

Grille removal

Grille mounting screws

MODEL BW-30 SITE PREPARATION

16

|

Sub-Zero Customer Care 800.222.7820

WOOD FLOOR

After properly locating the anti-tip brackets in the opening,

drill pilot holes

3

/16" (5) diameter maximum in the wall studs

or wall plate. Use the #12 screws and washers to secure the

brackets. Verify the screws penetrate through the ooring

material and into the wall studs or wall plate a minimum of

3

/4" (19). Refer to the illustration below.

CONCRETE FLOOR

After properly locating the anti-tip brackets in the opening,

drill pilot holes

3

/16" (5) diameter maximum in the wall studs

or wall plate. Drill

3

/8" (10) diameter holes into the concrete

a minimum of 1

1

/2" (38) deep. Use the #12 screws and

washers to secure the brackets to the wall, and use the

3

/8"

wedge anchors to secure the brackets to the oor. Verify the

screws penetrate the wall studs or wall plate a minimum of

3

/4" (19). Refer to the illustration below.

4" (102)

MIN

24"

(610)

SUBFLOORING

WOOD FLOOR

WALL PLATE

FINISHED

FLOORING

4" (102)

MIN

24"

(610)

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

1

/2"(38)

min

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

1

/2"(38)

MIN

Wood oor

Concrete oor

MODEL BW-30 INSTALLATION

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

brackets must be installed.

The two anti-tip brackets must be installed exactly 24"

(610)

from the front of the opening to the back of the

brackets and a minimum of 4"

(102) from the sides of the

opening. This depth will increase to 26

3

/16" (665) for a ush

inset installation based on

3

/4" (19) thick panels. Failure to

properly position the anti-tip brackets will prevent proper

engagement.

Use all anti-tip bracket hardware as instructed for wood or

concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the

#8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to

fasten the anti-tip brackets to the back wall.

ANTI-TIP HARDWARE

2 Anti-tip brackets

12 #12 x 2

1

/2" pan head screws

4

3

/8"–16 x 3

3

/4" wedge anchors

12 #12 at washers

4 #8–18 x 1

1

/4" truss head screws

4 Nylon Zip-it

®

wall anchors

subzero.com

|

17

MODEL BW-30 INSTALLATION

Custom Panels

For overlay and ush inset applications, custom door and

grille panels must be installed. The panel size is critical for a

proper t. To verify the panel requirements and dimensions,

refer to the Sub-Zero Design Guide at subzero.com/specs.

IMPORTANT NOTE: Flush inset applications require a

minimum

1

/2" (13) reveal on all sides.

Finish all sides of the custom panel. They may be visible

when the door is open or through the glass door.

CAUTION

A solid panel cannot be installed over the glass door.

Anti-Tip Bracket

CONCRETE WEDGE ANCHOR INSTALLATION

1 Drill a

3

/8" (10) diameter hole any depth exceeding the

minimum embedment. Clean the hole or drill additional

depth to accommodate the drill nes.

2 Assemble the washer and nut ush with the end of

anchor to protect threads. Drive the anchor through the

material to be fastened until the washer is ush with the

surface material.

3 Expand the anchor by tightening the nut 3–5 turns past

hand-tight position or to 25 foot-pounds of torque.

WARNING

Verify there are no electrical wires or plumbing in the

area which the screws could penetrate.

CAUTION

Always wear safety glasses and use other necessary

protective devices or apparel when installing or working

with anchors.

Anchors are not recommended for use in lightweight

masonry material such as block or brick, or for use in

new concrete which has not had sufcient time to cure.

The use of core drills is not recommended to drill holes

for the anchors.

18

|

Sub-Zero Customer Care 800.222.7820

MODEL BW-30 INSTALLATION

Panel Installation

DOOR PANEL

To install the custom door panel, remove the handle side

trim molding. Insert a screwdriver tip into the top corner slot

on the handle side and pop out the trim. Remove the screws

and frame. Refer to the illustration below.

The door has a

1

/4" (6) frame for the custom panel to slide

into. If the panel is thicker than

1

/4" (6), rout an edge around

the panel or mount the panel on a sheet of

1

/4" (6) thick

material, then insert into the frame.

A .10"

(3) space is required between the backer panel and

the custom panel to allow the panel to slide into the door

frame. Refer to the illustrations below for critical dimensions.

Install the handle hardware before inserting the panel. Large

D-style handles are recommend rather than knobs. The

screw heads must be countersunk into the panel.

Slide the panel into the frame.

To reinstall the door trim molding, insert the top of the trim

into the grooves at the top of the door and work downward,

snapping the trim into the clips on the door frame.

1

/8" (3) (OVERLAY)

CUSTOM PANEL

SPACER PANEL

BACKER PANEL

TRIM

5

/16" (8) min

1

/4" (6)

.10" (3)

CUSTOM

PANEL

SPACER

PANEL

BACKER

PANEL

3

/4"

(19)

typical

Panel assembly cross section

(overlay)

Panel assembly rear view

Door side trim

subzero.com

|

19

MODEL BW-30 INSTALLATION

Panel Installation

GRILLE PANEL

Remove the bottom grille frame by extracting the two lower

corner screws from each side of the grille assembly. Refer to

the illustration below.

With the bottom section removed, slide the custom grille

panel into the frame. If the panel is thinner than

1

/4" (6), a

ller material will need to be installed to achieve a proper

t. Once the panel is installed, reattach the bottom grille

frame by sliding the corner brackets back into position, then

reinstall the four corner screws.

BOTTOM

GRILLE

FRAME

Grille frame assembly

SIDE PANEL

When installing a custom side panel, an accessory kit is

required and is available through an authorized Sub-Zero

dealer. For local dealer information, visit the nd a show-

room section of our website, subzero.com. Stainless steel

and white enamel side panels are also available from an

authorized Sub-Zero dealer.

IMPORTANT NOTE: The use of side panels may change the

width of the opening.

A custom side panel must be a minimum of 24"

(610) deep

and

1

/2" (13) thick. Routing will be necessary for the side

panel to t ush against the side of the unit. Refer to the

illustrations below.

IMPORTANT NOTE: The height of the side panel will vary

with the height of the grille. Verify the nished height before

modifying the panels.

84"

(2134)

24"

(610)

OPTIONAL

TOE KICK

CUT-OUT

4" (102)

1

7

/8"(48)

1" (25)

ROUT TO

1

/

8

"

(3)

FRONT

OF SIDE

PANEL

2

5

/8"

(67)

MAIN

FRAME

SIDE PANEL

ROUTING

1" (25)

1

7

/8" (48)

1

/8" (3)

1

/

2

"

(13)

Side panel dimensions

Routing detail

20

|

Sub-Zero Customer Care 800.222.7820

MODEL BW-30 INSTALLATION

Alignment

LEVELING

Once the unit is in position, turn the front leveling legs

clockwise to adjust the height. The rear height adjustment

can be made from the front of the roller base. Using a

3

/8"

socket, turn the

3

/8" hex bolt clockwise to raise the unit or

counterclockwise to lower. Use the lowest torque setting

when using a power drill. Do not turn the rear leveling legs

by hand. Refer to the illustration below.

When the unit is properly leveled, door adjustments are less

likely to be necessary.

IMPORTANT NOTE: Level the unit to the oor, not the sur-

rounding cabinetry. This could affect the operation of the

unit, such as door closing.

WARNING

To reduce the possibility of the unit tipping forward, the

front leveling legs must be in contact with the oor.

FRONT

LEVELING LEG

REAR

ADJUSTMENT

Leveling

Placement

CAUTION

Before moving the unit into position, secure the door

closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

If the unit will be connected to a home security system, run

the lead wires through the compressor compartment prior

to positioning the unit. Refer to page 22. Once the unit is in

position, the wiring connections can be completed from the

front.

Plug the power cord into the grounded outlet, then roll the

unit into position. Verify the anti-tip brackets are properly

engaged.

IMPORTANT NOTE: If used, the side panels must be

installed before the unit is placed in its nal position. Refer

to page 19.

La pagina sta caricando ...

Sub-Zero 5310845 Guida d'installazione

Sub-Zero 5310845 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti