Munters VX36 VX48 Drive Manuale del proprietario

1© Munters Corporation, August 2017

QM1227r4

Instruction Manual

VX36 and VX48 with Munters Drive

36” and 48” Exhaust Fan

Models: VX36DFxxCP-Hx • VX48DFxxCP-Hx

Aerotech

VX36 & VX48

with RC cone and

Munters Drive*

*Patents Pending

2

QM1227r4

VX36 and VX48 Fans

with RC Cone and Munters Drive

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing an Aerotech VX36 and VX48 with Munters Drive fan. Munters equipment is

designed to be the highest performing, highest quality equipment you can buy. With the proper installation and

maintenance it will provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

3© Munters Corporation, August 2017

QM1227r4

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Fan Speciﬁ cations 4

2. Installation Instructions 5

2.1 Fan Installation 5

2.2 PT Style Shutter 10

2.3 PZ Style Shutter 11

3. Electrical Wiring 11

3.1 Recommended Wire Routing 12

3.2 Electrical Wiring 13

3.3 Recommended Wiring 14

4. Operation and Maintenance 20

4.1 Operation 20

4.2 Maintenance 20

5. Troubleshooting 21

6. Winterizing 22

6.1 Winterizing 22

6.2 Winter Weather Protection 22

7. Exploded View and Parts List 23-24

4

QM1227r4

Unpacking the Equipment

1.

1.1 Parts List

Each Fan includes:

1 - Munters Drive Fan

1 - Cone

1 - Guard

1 - Shutter

1 - Hardware Package (HP1167)

[A]

[B]

[C]

[D]

G

H

I

J

K - Dia.

A

C1

D

B

F1

A

E

C2

K - Dia.

F2

D

FAN

DIA.

A B C1

* C2* D E F1* F2* G H I J K-Dia.

WALL OPENING

(I.D., framed)

36” 6

7

⁄8” 22

7

⁄6” 6

7

⁄8” 6

7

⁄8” 45

3

⁄4” 45

3

⁄4” 22

7

⁄8” 22

7

⁄8” 50

5

⁄8” 24

1

⁄16” 8” -- 50

3

⁄8” 43” W 43”H

48” 8

7

⁄8” 28

7

⁄8” 8

7

⁄8” 8

7

⁄8” 57

3

⁄4” 57

3

⁄4” 28

7

⁄8” 28

7

⁄8” 55

3

⁄8” 24

7/

16

” 8” 2

5

⁄16” 63

5

⁄8” 55”W 55”H

*Dimensions plus/minus 1⁄4”, ﬁ eld verify.

Fan Specifications: 60Hz shown (50Hz available)

Power: 230 VAC or 230/460 VAC

Phase: 1 or 3

HP1167 – 36”/48” Fan, One Piece Cone

ID Qty. Cat. No. Description

[A] 12 KS2105 #14 x 1.5” Lag Screw, SS

[B] 8 KS0650

1

⁄4”-20 x

7

⁄8” Truss Head Bolt, SS

[C] 8 KW3012

1

⁄4” x 1” O.D. Flat Washer, SS

[D] 8 KN1717

1

⁄4”-20 Hex Flange, Nylock Nut, SS

1.2 Fan Dimensions:

5© Munters Corporation, August 2017

QM1227r4

Installation Instructions

2.

2.1 Fan Installation

Step 1

Construct the framed opening to correct size according to the Chart A. See Figure 1A and 1B.

FAN DIA. CONE

WALL OPENING

(W. X H.)

MINIMUM SPACING 'Z'

CENTER TO CENTER

DIMENSION

36” 36RC

43” W. x 43” H.

12” recommended; 8”minimum 51” Minimum

48” 48RC

55” W. x 55” H.

12” recommended; 9” minimum 64” Minimum

Chart A

Figure 1B Post Construction

Figure 1A Frame Construction

6

QM1227r4

Figure 3

Wall Framing

2" Minimum Framing for fan, Bottom

WallOpening (See Chart A, Page 4)

4" Minimum Framing for fan,

Top and Sides

Wall Framing

Step 2B

If fan needs to be mounted, so that shutter does not stick into

building then frame fan as shown in

Figure 3

. Top and sides

require 4" minimum and bottom requires 2" minimum.

Step 2A

Insert fan into the framed opening from the inside. While lifting fan up tight to framing, fasten top of

fan with (3) Lag Screw [A].

See Figure 2A and 2B

. Next, fasten bottom of fan, then both sides with

remaining (9) Lag Screw [A]. Install flashing around opening tight to fan and caulk around fan to

seal.

Figure 2A - Frame Construction

OUTSIDE INSIDE

2 x 4 Framing

#14 x 1.5" Lag Screws [A]

OUTSIDE INSIDE

Figure 2B - Frame Construction

Post

2 x 8 Banner Boards

2 x 8 Header Boards

Installation InstructionsChapter 2

7© Munters Corporation, August 2017

QM1227r4

Step 3

Installing the one piece cone may require 2 people. If temperature is above 50°F then proceed to

Step 5.

If temperature is below 50°F then proceed to

Step 4.

Step 4

Using Locking Sheet Metal Pliers bend the cone tabs outward to allow the cone to slide onto the fan easier.

See Figure 4.

Figure 4

Cone Tabs

Cone

Locking Sheet Metal Pliers

Cone Tab

Installation InstructionsChapter 2

Figure 5A

Figure 5B

Hole at 10 O'clock

Top Cone Tab

Cone

Flange Nut

[D]

36/48RC Cone

(outside)

Fan Outlet

(inside)

Truss Head

Bolt [B]

Washer [C]

Step 5

Look for the “TOP” label on the Polycone and set the top of the Polycone on top of the fan orifice and

install (2) Truss Head Bolts [B] through holes in fan outlet through the slots in the cone at about the 10

and 2 o’clock positions and fasten with Washers [C] and Flange Nuts [D]. Truss head of each bolt must

be on the inside of the fan outlet; washers and flange nuts must be on outside of cone.

See Figure 5A

and 5B.

Finger tighten nuts only at this time.

8

QM1227r4

Figure 6

Remaining Holes

Cone

Step 6

Work down the sides of the cone, sliding the cone tabs onto the fan until the bottom tab is in place. Keep

pressure on the cone to make sure tabs stay on the fan. Install (6) Truss Head Bolts [B], Washers [C] and

Flange Nuts [D] in the remaining holes in the fan outlet and slots in the cone to finish securing cone to fan.

See Figure 5B and Figure 6.

Tighten all nuts at this time, making sure not to over tighten.

NOTE: If installing your existing guard in the new Polycone then proceed to Step 9. If installing the new

snap-in guard then proceed to Step 7.

Installation InstructionsChapter 2

Figure 7

Step 7

The snap-in guard has a slight conical shape to it so, when installed the center of the guard should

protrude out slightly.

See Figure 7.

Cone

Guard

9© Munters Corporation, August 2017

QM1227r4

Figure 7B

Cone

Guard

Guard Ta

Guard Tab

Guard Slot in cone

Step 8

Starting at the bottom of the cone, locate one of the guard tabs and put the guard tab through the guard

slot in the cone.

See Figure 7B

. Then work up around the guard and install each of the other guard tabs

in each of the corresponding guard slots. Some force may be required to snap the last tab into the last

slot, pull out on the center of the cone while pushing in on the guard tab until it snaps into place.

Installation InstructionsChapter 2

Figure 8B

Guard Mounting

Pad

Figure 8A

Nut

Bolt

Guard Mounting Pad

Guard

Fan Outlet

Step 9

If installing your existing guard into the new cone, locate the flat guard mounting pads on the cone and

drill a

9

⁄32” dia. hole in the center of each pad. Then insert existing guard into cone with the guard eyelets

facing away from you. Line up each eyelet with a hole in the guard pads. Secure guard to cone using (8)

existing Bolts and Nuts.

See Figure 8A and 8B

. Tighten all nuts at this time.

Guard eyelet

10

QM1227r4

Installation InstructionsChapter 2

Figure 9

PT Shutter

2.2 PT Style Shutter

Step 10

Insert PT Shutter into fan by sliding the bottom flange

of shutter into bottom shutter clips and pressing shutter

inward.

See Figure 9.

Fixed Bottom

Shutter Clip

NOTE: PT Shutter extends into room 2

5

⁄16” from back of fan.

Step 11

Fasten shutter in place by rotating the side and top shutter clips over the shutter flanges.

See Figure 10.

Installation is now complete, proceed to Electrical Wiring Section.

Figure 10

11© Munters Corporation, August 2017

QM1227r4

Installation InstructionsChapter 2

2.3 PZ Style Shutter

Step 12

Insert PZ shutter into fan by sliding the bottom flange

of shutter into bottom shutter clips and pressing

shutter inward,

See Figure 11A

. Fasten shutter in

place by rotating the side and top shutter clips over

the shutter flanges,

See Figure 11B.

Installation is

now complete, proceed to electrical wiring section.

PZ Shutter

Fixed Bottom Shut-

ter Clip

Figure 11B

Figure 11A

12

QM1227r4

Electrical Wiring

3.

3.1 Recommended Wire Routing

The Munters Drive Fan comes with a coil of electrical cable that is pre-wired to motor. Find the end of the cable

and route it outside the fan and connect it to the incoming power supply and/or the safety cut-off switch. (Safety

cut-off switch by others). See Figure 12A.

Electrical Cable

Junction Box

Figure 12A

WARNING: Fan is designed to be operated with shutter in place. Do not apply power to fan without

shutter being installed.

13© Munters Corporation, August 2017

QM1227r4

KEY:

L1=Line 1

L2=Line 2

L3=Line 3

H=Hot

N=Neutral

G=Ground

All wiring should be installed in accordance with National, State, and Local electrical

codes. Fans used to ventilate livestock buildings or other rooms where continuous air

movement is essential should be connected to individual electrical circuits, with a minimum

of two circuits per room. For electrical connection requirements, refer to diagram on motor

nameplate and to information enclosed with the environmental control to be used.

Single Phase and Three Phase Munters Drives: Power supply for fans to have Circuit

Breaker or Fuse Protection. The installer must refer to NEC and local codes to ensure

safety and compliance. See Figure 12B & 12C.

If recommended lightning protection was purchased, wire it to the fan power supply as shown and secure the

lightning protection unit near the disconnect or the bus panel. See Figure 12B & 12C.

NOTE: A safety cut-off switch should be located adjacent to each fan.

T1

T2

T3

G

Three Phase

Power Out to Fan Motor

Three Phase

Power Supply for Fan

L1

L2

L3

G

Safety

Cut-Off Switch

Recommended Lightning Protection

FC2003, 230V, 1 Phase

240 VAC

Power Supply for Fan

L1

L2

G

T1

T2

G

240 VAC

Power Out to Fan

Figure 12C

Three Phase

Figure 12B

Single Phase

Safety

Cut-Off Switch

Recommended Lightning Protection

FC2006, 230V, 3 Phase

FC2009, 460V, 3 Phase

3.2 Electrical Wiring

Electrical WiringChapter 3

WARNING

!

High Voltage, disconnect

power before servicing.

14

QM1227r4

3.3 Recommended Wiring

Electrical WiringChapter 3

Figure 13A

Default Operation Full Speed

The Munters Drive fan ships configured for simple ON/OFF operation. When electrical power is applied to

the main cable and the ‘RUN’ Switch is in the ‘ON’ Position, the fan will start and run at full speed.

See Figure 13A.

QM1227r4

Electrical WiringChapter 3

When making connections to Munters Drive Box, be sure to use the supplied watertight fittings with only

1 cable per fitting. If watertight fittings are not used or if 2 cables or more are in 1 watertight fitting,

equipment failure from water damage will not be covered under warranty. If 2 or more cables are used in

1 watertight fitting, they must be sealed on both sides of Munters Drive Box wall to prevent water infiltration.

If you are going to run the Munters Drive with a signal from a control, carefully remove 6 screws and the

cover and save to reinstall later. Carefully punch the knock-out from the bottom of the Munters Drive Box and

install the Watertight connector as shown. See Figure 13B and 13C.

Figure 13B

Figure 13C

16

QM1227r4

Electrical WiringChapter 3

Figure 13D

On/Off Remotely

To operate the Munters Drive On/Off with a control, Slide the ‘RUN’ switch, located on the circuit board in

the Munters Drive Box, to the ‘OFF’ position. Now wire an ‘ON’ command from the ‘COMMON’ terminal

to the input relay in the control and from the output of the control relay to the ‘RUN’ terminal in the Munters

Drive Box. See Figure 13A & 13D.

QM1227r4

Electrical WiringChapter 3

To operate the Munters Drive Off/Low/High with a control, slide the ‘RUN’ switch, located on the circuit

board in the Munters Drive Box, to the ‘OFF’ position. Now wire an ‘ON’ command from the ‘COMMOM’

terminal to the input relay in the control and from the output of the relay to the ‘RUN’ terminal in the Munters

Drive Box. Then connect the output of the control relay for ‘LOW’ to the ‘REDUCED FLOW’ terminal in the

Munters Drive Box. See Figure 13E.

Figure 13E

Off/Low/High Remotely

18

QM1227r4

Electrical WiringChapter 3

Figure 13F

Variable Speed Operation

To Operate the Munters Drive variable with a 10-0V Signal, slide the ‘RUN’ switch, located on the circuit

board in the Munters Drive Box, to the ‘ON’ position. Connect wires from the ‘0-10V IN’ and ‘0-10V

COMMON’ terminals in the Munters Drive Box to the 10-0V output in the control. See Figure 13F.

QM1227r4

Electrical WiringChapter 3

To operate the Munters Drive Off/Variable with a 10-0V Signal, slide the ‘RUN’ switch, located on the circuit

board in the Munters Drive Box, to the ‘OFF’ position. Now wire an ‘ON’ command from the ‘COMMON’

terminal to the input relay in the control and from the output of the control relay to the ‘RUN’ terminal in

the Munters Drive Box. Also, connect wires from the ‘0-10V IN’ and ‘0-10V COMMON’ terminals in the

Munters Drive Box to the 10-0V output in the control. See Figure 13G.

Figure 13G

On/Off with Variable Speed Operation

WARNING: Fan is designed to be operated with shutter in place. Do not apply power to fan without

shutter being installed.

20

QM1227r4

Operation and Maintenance

4.

1) INITIAL START-UP: With electrical power off, verify that the fan propeller

turns freely and that all fasteners are secure. With shutter in place, turn on

electrical power and confirm that the fan operates smoothly.

2) TEMPERATURE ADJUSTMENTS: Set the fan control to the temperature

shown on your Munters ventilation system drawing, or to a value which will

provide the desired environmental conditions.

4.1 Operation

WARNING

!

Moving parts, disconnect

power before servicing.

WARNING

!

High Voltage, disconnect

power before servicing.

WARNING

!

Do not power wash

electrical devices.

WARNING

!

Do not apply power

with shutter out.

4.2 Maintenance

The following inspection and cleaning procedures should be performed

monthly:

1) INSPECT PROPELLER: Check that propeller is secure on drive hub and that

there are no signs of damage. The blades are of a self-cleaning design and

should not require maintenance.

2) CLEAN regularly for best results:

• FAN MOTOR: Remove any dust accumulation from motor using a

brush or cloth. (DO NOT use a pressure washer). A clean motor will run

cooler and last longer. At the same time, verify that the motor is secure in

its mount.

• SHUTTER: Carefully clean dust from shutter and frame so that shutter

opens and closes freely. A brush or cloth should be used.

• GUARD: Clean any dust or feathers from fan guards using a brush.

Dirty guards can reduce airflow.

3) CHECK FASTENERS: For safety, all fasteners should be inspected. Tighten

any loose connections.

4) INSPECT FAN CONTROL: With power disconnected, inspect all electrical

connections. Wiring should be secure and in good condition. Remove any

dust build-up from control case and sensor using a soft brush or cloth.

NEVER CLEAN ELECTRICAL EQUIPMENT WITH A PRESSURE WASHER!

La pagina sta caricando ...

Munters VX36 VX48 Drive Manuale del proprietario

Munters VX36 VX48 Drive Manuale del proprietario

in altre lingue

Documenti correlati