Munters BI28SPM Manuale del proprietario

Marca: Munters

Modello: BI28SPM

Tipo: Manuale del proprietario

1© Munters Corporation, May 2017

QM1112r3

Instruction Manual

BI28SPM Ceiling Inlet

Bi-Flow, Spring/Mechanical

Models: BI28SPM • BI28SPM-01

BI28SPM

Ceiling Inlet

QM1112r3

BI28SPM Inlet

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing a Munters inlet. Munters equipment is designed to be the highest performing, highest

quality equipment you can buy. With the proper installation and maintenance it will provide many years of

service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

3© Munters Corporation, May 2017

QM1112r3

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Inlet Dimensions 4

2. Installation Instructions 5

2.1 Framing 5

2.2 Inlet Mounting 6

3. Latch Operation 9

4. Cabling 10

5. Operation 12

6. Performance Data 13

7. Exploded View and Parts List 14

QM1112r3

1.1 Parts List

Unpacking the Equipment

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all

components for signs of shipping damage. Any shipping damage is the customer's responsibility and should be reported

immediately to your freight carrier.

1.2 Inlet Dimensions

⁄16”

Each BI28SPM Inlet includes:

1 - Plastic Frame with 2 doors attached

1 - Insulation Stop, 12” tall

2 - Spring Counterweight Assembly

1 - Hardware Package as follows

⁄16”

⁄4”

HP1239 for BI28SP/BI28SPM Inlets

ID Qty. Cat. No. Description

[A] 8 KS1402 #9-15 x 1.5” Hex Head Screw

[B] 1 AC1381

⁄8” Dia. Cable Clamp, ZP

5© Munters Corporation, May 2017

QM1112r3

2.1 FRAMING

Step 1

Construct a framed opening in ceiling that is

⁄2”W. x 25

⁄2”L. and fasten to trusses or

bracing between trusses. Trim out framing with

‘J’-trim if a metal ceiling is used. See Figure 1A

and 1B. If inlet is being installed in a house

with a Tri-Ply ceiling, construct frame as shown

in Figure 1C.

Installation Instructions

Figure 1A

Figure 1B

Step 2A

The Spring Counterweight Assemblies

and other hardware will already be

assembled as shown in Figure 2. The

Lift Line should be turned towards

actuator and Eye Bolt will be away

from actuator.

Step 2B

The doors will be held closed with the

latch. Keep doors latched and remove

the (4) screws shown. While removing

these screws make sure the washer

comes off the inlet and stays with the

screw. These screws will be used in

Step 3.

See Figure 2.

Figure 1C

Figure 2

If installing inlets near heaters, it is

recommended to install the BI28/BI48 inlet

at a location far enough from heaters that

will give a maximum temperature of 150°F.

This should be approximately 2-3 ft. from

the heater.

IMPORTANT

QM1112r3

Installation InstructionsChapter 2

Step 3

Turn Spring Counterweight Assembly over and set on frame of inlet and secure assembly with (2) of

the screws and washers removed in Step 2B. See Figure 3. Repeat for other Spring Assembly.

2.2 Inlet Mounting

Figure 4

Step 4

Install provided Insulation Stop into framed opening as shown using screws or staples (not provided).

See Figure 4.

Figure 3

7© Munters Corporation, May 2017

QM1112r3

Installation InstructionsChapter 2

Figure 5A

Step 5

Apply bead of caulk around top of inlet as shown in Figure 5A. Position inlet into framed opening and

attach inlet using (8) Hex Head Screws [A] provided. See Figure 5B. Be careful not to over tighten as this

may pull the Inlet Frame out of shape.

Step 6

To ensure an airtight fit, caulk around outside of 2x4 Framing and Inlet Frame.

Figure 5B

QM1112r3

Installation InstructionsChapter 2

Step 7

Proceed to routing main actuator cable or rod through holes in Inlet Frame. It is required to utilize a spring

or weight on actuator cable end opposite actuator. Once the cable is routed and the actuator is in the open

position, begin connecting the Lift Lines from each inlet door to the actuator cable using Cable Clamp [B]

provided. See Figure 6A and 6B.

Figure 6A

Figure 6B

9© Munters Corporation, May 2017

QM1112r3

Latch Operation

Step 8

Latch is pre-installed near center of door. Rotate latch upward to unlock and downward to lock.

When inlet is in normal operation, be sure latch is in up position so it does not interfere with door

closing. See Figure 7A and 7B.

Figure 7A

Latch Shown in Open Position

Figure 7B

Latch Shown in Closed Position

QM1112r3

Cabling

Step 9

Attach pulleys in line with the main rod or cable running through each BI28/BI48. See Figure 8A and 8B.

Figure 8A

Figure 8B

11© Munters Corporation, May 2017

QM1112r3

CablingChapter 4

Step 10

On each end of the run of BI28/BI48 inlets run a cable

through pulleys to winch or actuator on one end and to

weights or return spring on other end.

See Figure 8A, 8B and 9.

Figure 9

Step 11

With the winch or actuator at its fully closed position, check and

readjust each BI28 door tightly closed. Use winch or actuator to

open and close inlets a few times to make sure the doors open and

close smoothly

QM1112r3

Operation

Note:

To achieve a lower static pressure

move the spring toward hinges (inward)

and to achieve a higher static pressure

move spring towards outside of the inlet

(outward). See Figure 10.

Step 1

Start by setting each spring as light

as possible, that still allows the doors

to close when the fans are off. Note:

installation on a sloped ceiling will

typically require a heavier setting on the

high (uphill) side and a lighter setting on

the low (down hill) side.

Step 2

With inlets winched fully closed, turn

on your minimum ventilation fans.

Then adjust (release) the mechanical

hardware (actuator or winch) gradually

until you achieve the desired static

pressure. The winching limits the inlet

door opening so that all the doors open

evenly and the desired static pressure is

achieved when the minimum ventilation

fans run..

Step 3

Once the winching is set, turn fans off

and recheck to ensure all the inlets are

closing fully.

Figure 10

Note:

Spring Position settings

may vary from inlet to

inlet. Adjust each inlet

as needed.

QM1112r3

Performance Data

QM1112r3

Exploded View and Parts List

QM1112r3

This page left blank intentionally

QM1112r3

Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE-164 26 Kista, Sweden. Phone +46 08 626 63 00, Fax +46 8 754 56 66.

Munters Corporation 2691 Ena Drive Lansing, MI 48917 U.S.A. Phone +1 800-227-2376, Fax +1 517-676-7078

www.munters.us

Australia Munters Pty Limited, Phone +61 2 6025 6422, Brazil Munters Brasil Industria e Comercio Ltda, Phone +55 41 3317 5050, Canada/US Munters

Corporation Lansing, MI Phone +1 517 676 7070, China Munters Air Treatment Equipment (Beijing) Co. Ltd, Phone +86 10 80 481 121, Denmark Munters A/S,

Phone +45 9862 3311,

India Munters India, Phone +91 20 3052 2520, Indonesia Munters, Phone +62 818 739 235, Italy Munters Italy S.p.A., Chiusavecchia,

Phone +39 0183 52 11, Japan Munters K.K., Phone +81 3 5970 0021, Korea Munters Korea Co. Ltd., Phone +82 2 761 8701, Mexico Munters Mexico, Phone

+52 818 262 54 00, Russia Munters AB, Phone +7 812 448 5740, Singapore Munters Pte Ltd., Phone +65 744 6828, South Africa and Sub-Sahara Countries

Munters (Pty) Ltd., Phone +27 11 997 2000, Spain Munters Spain S.A., Phone +34 91 640 09 02, Sweden Munters AB, Phone +46 8 626 63 00, Thailand

Munters Co. Ltd., Phone +66 2 642 2670, Turkey Munters Form Endüstri Sistemleri A.Ş, Phone +90 322 231 1338, USA Munters Corporation Lansing, MI Phone

+1 517 676 7070, Vietnam Munters Vietnam, Phone +84 8 3825 6838, Export & Other countries Munters Italy S.p.A., Chiusavecchia Phone +39 0183 52 11

BI28 Inlets are developed and produced by Munters Corporation, Lansing, Michigan U.S.A. 1-800-227-2376

Munters BI28SPM Manuale del proprietario

Marca: Munters

Modello: BI28SPM

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Munters BI28SPM Owner's manual

Munters BI28SPM Manuale del proprietario

Munters BI28SPM Manuale del proprietario

in altre lingue

Documenti correlati