Agria 4500 Manuale del proprietario

- 4500 021 71 cm

- 4500 031 85 cm

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No.

998 784-A 07.08

&

Brush CutterBrush Cutter

Brush Cutter

4500 Hydro4500 Hydro

4500 Hydro

OperatingOperating

Operating

InstructionsInstructions

Instructions

2 Brush Cutter 4500 Hydro

Please complete:

Machine Type No.:.......................

ID/Machine No.:

...................................................

Engine Type:................................

Engine No.:..................................

Date of Purchase:........................

For name plate, refer to

page 3/fig. A/25

For engine type and number, refer

to page

46/fig. B/3

Please state these data when orde-

ring spare parts to avoid wrong deli-

veries.

Only use original agria spare parts!

Specifications, figures and dimensi-

ons stated in these instructions are

not binding. No claims can be derived

from them. We reserve the right for

improvements without changing the-

se instructions.

This delivery comprises:

l

Operating instructions agria

l

Operating instructions Engine

l

Bildup mower

l

Tool kit

Symbols

Warning – danger

Atttention

Important Information

Choke

Engine

Engine Start

Engine Stop

Engine speed

Engine oil level

Transmission oil

Fuel

Fuel filter

Forward

Reverse

Fast

Slow

Engage cutter element

Disengage cutter element

Park brake

Closed (locked)

Open (Unlocked)

Tyre air pressure

infinitely linear

è

- Serviceç= contact

your agria-workshop

Lifting point, fixing point for

recovery, tieing up, towing

away

Symbols, Name Plate

Brush Cutter 4500 Hydro 3

Fig. A

23

21

22

24

25

26

27

30

28 29

Y

Z

30

Designation of Parts

1

2

3

456

7 8

9

12

14

13

10

11

4 Brush Cutter 4500 Hydro

Fig. A:

1 Handlebar

2 Tool kit

3 Fuel tank

4 Belt guard cover

5 Front frame

6 Locking bolt

7 Front wheel

8 Front tarpaulin guard

9 Mulch housing

10 Rubber cap strips (on either side) on the mulch housing (only vers. 85

cm)

11 Rubber cap strip on the gear

12 Drive wheel

13 Lug for lashung down and lifting (on either side)

14 Engine

21 Crank for cutting height adjustment

22 Clamping lever for handlebars height adjustment

23 Handle for handlebars lateral adjustment

24 Mulching drive shifting lever

25 Engine shut-off switch - only version 85 cm (4500 031)

26 - version 71 cm (4500 021) - Speed adjusting lever

- CHOKE

- Engine shut-off switch

- version 85 cm (4500 031) - Speed control lever

27 Driving speed lever

28 Steering brake lever left

29 Steering brake lever right

30 Safety circuit lever left and right

31 Name plate, ID/Machine No.

Y Locking lever for driving control

Z Locking lever for park brake

Designation of Parts

Brush Cutter 4500 Hydro 5

Index

3

5

6

2

1

4

Recommendations

Fuel ............................................ 6

Maintenance and Repair ........... 6

Designation of Parts .... 3, 46

1. Safety Instructions....7-12

2. Specifications

Dimensions .............................. 13

Machine ................................... 14

Petrol Engine ........................... 15

Vibration Acceleration Value.... 15

Noise Levels ...................... 15, 16

Operation on Slopes.......... 15, 16

3. Devices and Operating

Elements

Engine...................................... 17

Speed Adjusting Lever ............ 18

Choke....................................... 18

Engine Shut-off Switch ............ 18

Safety Circuit Lever ................. 19

Driving Control ......................... 20

Mulching Drive ......................... 20

Steering Brake ......................... 21

Handlebar ................................ 22

Cutting Height Adjustment....... 23

Front Wheels............................ 23

Fixing/Lifting points................ 23

4. Commissioning and

Operation

Commissioning the Machine ... 24

Starting the Engine ........... 25 - 26

Driving...................................... 27

Mowing..................................... 27

Danger Zone............................ 28

Working on Slopes .................. 28

Switching off the Engine .......... 29

5. Maintenance

Engine Oil ................................ 30

Engine Oil Filter ....................... 30

Fuel Filter ................................. 30

Cooling System ....................... 31

Exhaust.................................... 31

Governor .................................. 31

Spark Plug ............................... 31

Hydrostat Gear ........................ 32

Hydrostat Cooling Fan ............. 32

Tarpaulin Guard, Rubber Cap . 32

Adjustments on Levers ............ 33

Safety Circuit ........................... 34

Engine Shut-off Switch ............ 34

Cutter Brake............................. 34

V-Belt ....................................... 35

Chain Guard ............................ 35

Lubrication Points .................... 36

Drive-wheels ............................ 36

Knives ...................................... 37

General Maintenance, Cleaning . 38

Storage .................................... 39

Maintenance Schedule .... 40

Inspection and Maintenance

Chart.................................. 41

6. Troubleshooting.....42 - 43

Electrical Wiring ............... 44

Varnishes, Wear Parts...... 45

Conformity Declaration ... 47

Note fold-out pages!

Fig. A ................................... 3

Fig. B (Engine) .................. 46

6 Brush Cutter 4500 Hydro

Maintenance and

Repair

The trained mechanics of your agria

workshop carry out expert maintenance

and repair.

You should only carry out major mainte-

nance work and repairs on your own, if

you have the proper tools and know-

ledge of machines and internal combu-

stion engines.

Do not hammer against the flywheel with

a hard object or metal tools as it might

crack and shatter in operation causing

injuries and damage. Only use suitable

tools for pulling the flywheel.

Recommendations

Fuel

Petrol Engine

This petrol engine runs smoothly on

commercial unleaded regular petrol.

Do not add oil to petrol.

If, for environmental reasons, you use

unleaded petrol, make sure the fuel is

drained completely when shutting down

the engine for more than 30 days. This

is to prevent resin residues from depo-

siting in the carburetor, fuel filter, and

tank. Or add a fuel stabilizer.

For further instructions refer to „Engine

Preservation“.

Brush Cutter 4500 Hydro 7

Before starting the engine, read the ope-

rating instructions and note:

Warning

This symbol marks all paragraphs in the-

se operating instructions which affect

your safety. Pass all safety instructions

to other users and operators.

Due Use

The brush cutter agria has been desi-

gned for mowing use in farming and fo-

restry for example for grass mainte-

nance (due use).

Any other type of operation is conside-

red undue. The manufacturer is not lia-

ble for any damage resulting from un-

due use, for which the risk lies with the

user alone.

Due use includes compliance with

manufacturer’s instructions on operati-

on, maintenance and repair.

Any unauthorized changes to the tool

carrier render manufacturer liability null

and void.

1. Safety Instructions

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The standard accident prevention regu-

lations must be adhered to, as well as

all other generally accepted rules go-

verning operational safety, occupational

health and road traffic regulations.

For drives on public roads, the latest traf-

fic code applies.

Accordingly, check the tool carrier for

road and operational safety each time

you take up operation.

Only persons familiar with the tool car-

rier and instructed on the hazards of

operation are allowed to use, maintain

and repair the tool carrier.

Young persons of 16 years or younger

may not operate the tool carrier!

Only work in good light and visibility.

Operator’s clothes should fit tightly. Avoid

wearing loosely fitting clothes. Wear

solid shoes.

Note the warning and instruction signs

on the tool carrier for safe operation.

Compliance is for your own safety.

When transporting the tool carrier on

vehicles or trailers outside the area to

be cultivated, the engine must be swit-

ched off and you must wait until the

knives have stopped rotating complete-

ly.

Careful with rotating tools – keep at a

safe distance!

1

8 Brush Cutter 4500 Hydro

Due to its centrifugal mass, the cutter

blade can follow up. During that time,

do not stay too close to the mower hou-

sing. Only when the cutter blade is com-

pletely standing still and the spark plug

connector has been withdrawn, works

on the brush cutter are permitted.

Foreign powered parts shear and

squeeze!

Riding on the machine during operation

is not permitted.

Match operating speed to conditions.

Do not change settings of governor. High

engine speed increases risk of acci-

dents.

Working Area and Danger

Zone

The user is liable to third parties wor-

king within the brush cutter’s working

range.

Staying in the danger zone is not per-

mitted.

If the operator should notice that a per-

son or animal is staying within this area,

the machine must be shut down without

delay and must not be operated again

before the area is free again.

Check the immediate surroundings of

the machine before you start it. Watch

out for children and animals.

Before you start work, clear the area

from any foreign object. During operati-

on, always watch out for further objects

and remove them in time.

For operation in enclosed areas, ensu-

re that a safety distance is kept to enclo-

sures to prevent damage to tools.

Be careful when mowing; ensure that the

cutter blades does not seize obstacles

such as border stones, enclosures, roots

etc.

Operation and

Safety Devices

Before You Start the Engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to shut off the en-

gine quickly and safely in an emergen-

cy situation.

Ensure that all protective devices are

mounted and positioned to provide pro-

tection.

Starting the engine

Do not start engine in closed rooms. The

carbon monoxide contained in the ex-

haust fume is extremely toxic when inha-

led!

Before you start the engine set all opera-

ting elements to neutral or idling position.

Be careful upon starting and during

mowing; do not come directly close

to the cutting section with your hands

or feet.

When starting, it is not permitted to bring

the brush cutter into an upright position

or to tilt it.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion.

1. Safety Instructions

1

Brush Cutter 4500 Hydro 9

Operation

Never leave the operator’s position whi-

le the brush cutter is at work.

The carrying of additional persons is not

allowed.

If clogging occurs in the cutting section,

shut off the engine, withdraw the spark

plug connector and clean the cutting

section with an appropriate tool.

In case of damage to the brush cutter,

immediately shut off the engine and

have it repaired.

Should the machine start to vibrate in

an unusually strong manner, an imme-

diate inspection is necessary.

If steering causes problems, immedia-

tely bring the brush cutter to a halt and

shut it off. Have the malfunction elimi-

nated without delay.

Driving speed must always be adjusted

to suit the surrounding conditions. When

driving uphill or downhill and driving

across a slope avoid sudden turns.

When driving in curves switch off the

differential lock.

If possible, always work across the slo-

pe.

Pay careful attention to hills, dips and

other unforeseen dangers.

Stop the cutting tools before crossing

surfaces other than grass.

Never operate machines with damaged

or unfitted safety protection gear.

End of Operation

Never leave the brush cutter unatten-

ded with the engine running.

Before you leave the brush cutter, shut

off the engine, close the fuel cock, en-

gage the parking brakes and secure

against rolling away.

Before you leave the ride-on brush cut-

ter fully lower the cutting tools.

Secure brush cutter against unauthori-

zed use, remove the ignition key.

Mowing Equipment

In cases of improper operation the sharp

blades of the cutter blades pose a consi-

derable danger of injury. Wear protecti-

ve gloves when working on the cutter

blades.

When changing the cutter blades ensu-

re that the screwing movement leads

away from the blade edges.

Protective glasses and protective gloves

must be worn when sharpening the cut-

ter blades.

Maintenance

Never carry out any maintenance or cle-

aning with the engine running.

After switching off the drive, the brush

cutter may continue to coast due to its

centrifugal mass. Do not go too near to

the brush cutter during this time. Only

when it has come to a complete stand-

still can it be worked upon.

Before you work on the engine, always

remove spark plug connector.

1. Safety Instructions

1

10 Brush Cutter 4500 Hydro

Check regularly and, if necessary, re-

place all protecting devices and tools

subject to wear and tear.

Replace damaged cutting tools.

Observe maintenance intervals of the

cutter blades.

Always wear safety gloves and use pro-

per tools when exchanging the cutter

sections.

Repair work, such as welding, grinding,

drilling etc., is not allowed to be carried

out on load-bearing, safety-critical parts.

Keep brush cutter clean to avoid risk of

fire.

Check nuts and bolts regularly for tight

fit and re-tighten, if necessary.

Ensure that you re-install all safety and

protective devices and adjust them pro-

perly after maintenance and cleaning.

Only use original agria spare parts. All

other commercial spare parts must cor-

respond to quality and technical requi-

rements specified by agria.

Storage

It is not allowed to store the brush cut-

ter in rooms with open heating.

Never park the brush cutter in closed

rooms with fuel left in tank. Fuel vapours

are hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed rooms.

Extreme danger of intoxication! For the

same reason, also replace damaged

exhaust pipe immediately.

Be careful when handling fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot

engine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine shut off and

cooled down.

Do not spill any fuel, use a proper filling

device (e.g. funnel).

In case of fuel-spillage, pull the brush

cutter away from the spillage before you

start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Liquids leaking under high pressure, e.g.

fuel, can penetrate the skin and cause

severe injuries. Immediately see a doc-

tor.

Store anti-corrosive agents and stabili-

zing liquids out of reach of children. If

sickness and vomiting occur, see a doc-

tor. If fuel has contacted eyes, rinse

them thoroughly, avoid inhaling of va-

pours.

Read and observe enclosed instruc-

tions.

1. Safety Instructions

1

Brush Cutter 4500 Hydro 11

Before you dispose of opened and see-

mingly empty pressurised tins (e.g. of

assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark forma-

tion or flames. If necessary, dispose of

tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil used is of specified quali-

ty. Storage is in approved cans only.

Dispose of oil, greases, and filters se-

parately and properly.

Tyres and

Tyre Air Pressure

When working on wheels, make sure

tool carrier is parked properly and se-

cured against rolling off.

Any repairs are to be carried out by trai-

ned mechanics only and with the appro-

priate tools.

Regularly check tyre air pressure. Ex-

cessive pressure may cause bursts.

Re-tighten attachment bolts of drive-

wheels or check tightness when doing

maintenance work.

Electrical System

Persons having a pacemaker may not

touch live parts of the ignition system

when the engine is running.

1. Safety Instructions

1

12 Brush Cutter 4500 Hydro

Explanation of Warning Signs

Attention:

Carefully read operator's manu-

al before handling the machine.

Observe instructions and safe-

ty rules when operating.

Shut off engine and remove

spark plug connector before

cleaning, perfoming mainte-

nance or repair work.

During operation keep at a

safe distance from cutter bla-

des.

Wait until all machine compon-

ents have completely stopped

before touching them.

Danger - flying objects; keep

safe distance from the machi-

ne as long as the engine is

running.

Do not open or remove safe-

ty shields while engine is run-

ning.

Use sprag before machine is

uncoupled or parked.

Stay clear of hot surfaces.

The exhaust fumes contain

breath poisons - keep di-

stance. Never let the engine

run in closed rooms.

Before each fuel fill, shut off

the engine and wait until it has

cooled off.

1. Safety Instructions

2

Explanation of

Prohibition Signs

No open fire

Do not smoke!

Do not spray with

water

Do not start the

engine in closed

rooms!

Signs

When working with

the machine, wear

individual protecti-

ve ear plugs.

Wear protective

gloves.

Wear solid shoes.

Check engine oil

level.

Brush Cutter 4500 Hydro 13

2. Specifications

2

Machine

Dimensions (mm)

..4500 021 (71 cm) ........ 4500 031 (85 cm) ..........

A................... 1.160 ............................1.460

BF ................... 110 .................................90

BH ................... 650 ............................... 650

BM................... 820 ............................... 985

BR ................... 870 ............................... 850

h ...................... 890 ............................... 920

HH ......... 820 ± 230 .....................890 ± 230

l .................... 1.640 ............................. 2000

L ................... 2.240 ............................ 2.500

RH ................... 780 ............................... 660

SH ............ 50 - 105 ........................50 - 105 ... (60 - 115 Mulching kit)

PH ..............340 kN......................... 430 kN

PM..............295 kN......................... 330 kN

VHL ................. 385............................... 385

VHR ................ 385 ............................... 385

β.........................

45° ............................... 38°

δ

R....................45° ............................... 45°

partial view A

14 Brush Cutter 4500 Hydro

2. Specifications

Brush cutter 71 cm

4500 021

Driving axle: .............. Hydrostat gear

Driving speeds: ...................................

Forward ............................ 0 - 6,0 km/h

Reverse............................ 0 - 3,0 km/h

Oil for hydrostat:

......................... permanent oil volume

Steering: ...Single-wheel multiple disc

clutch brake

Tyres:

rear..... 16x6.50-8 wide track field tyre

Tyre air pressure: .............0,6 - 1,0 bar

..................................................... 4PR

front...................... Caster 215x55 mm

........................................... full rubber

................................ with ball bearings

Fuel tank capacity: ........approx. 7,0 l

Weight:

Empty weight:

(with fuel tank filled up): .......

4500 021 .................................. 203 kg

Cutter unit:...................Rotary mower

...........with reciprocating knife system

Working width: ....................... 710 mm

Cutting height:..................... steplessly

..............................from 50 to 105 mm

Optional:...........Mulching kit 4549 021

Cutting height:..................... steplessly

..............................from 60 to 115 mm

2

Brush cutter 85 cm

4500 031

Driving axle: .............. Hydrostat gear

Driving speeds: ...................................

Forward ............................ 0 - 6,0 km/h

Reverse............................ 0 - 3,0 km/h

Oil for hydrostat:

......................... permanent oil volume

Steering: ...Single-wheel multiple disc

clutch brake

Tyres:

rear.......................... 5.00-10 field tyre

Tyre air pressure: .............0,6 - 1,0 bar

..................................................... 4PR

front...................... Caster 260x60 mm

........................................... full rubber

................................ with ball bearings

Fuel tank capacity: ........approx. 7,0 l

Weight:

Empty weight:

(with fuel tank filled up): .......

4500 031 .................................. 230 kg

Cutter unit:...................Rotary mower

...........with reciprocating knife system

Working width: ....................... 850 mm

Cutting height:..................... steplessly

..............................from 50 to 105 mm

Optional:...........Mulching kit 4549 031

Cutting height:..................... steplessly

..............................from 60 to 115 mm

Brush Cutter 4500 Hydro 15

2. Specifications

Petrol Engine for 71 cm

Manufacturer: ......................... Honda

Type: .................... GXV 340 UT2 DN4

Bore: ........................................ 82 mm

Stroke: ..................................... 64 mm

Cubic capacity: ................... 337 ccm

Output: ............... 8,1 kW at 3600 rpm

Max torque:............................. 24 Nm

.........................................at 2500 rpm

Construction: ............. Fan-air-cooled

Spark ignition engine with overhead

valves, vertically crankshaft

Spark plug: ................. NGK BPR5ES

Spark plug gap 0,76 mm

Ignition:

Electr. magnetic ignition, contactless

Radio remote screened ............ as per

VDE 0879

Fuel:....................................................

Commercial.........................................

.......................unleaded regular petrol

min. octane number 85 - 91 RON

(refer to fuel recommendations)

Fuel consumption:........... 313 g/kWh

Fuel filter:...........................feul-online

Air filter: .......... Dry filter element with

foamed preliminary filter

Carburettor: .......... Throttle valve type

Rated speed: ...................... 3200 rpm

Top no-load speed: ............3350 rpm

Idling speed:.......................1200 rpm

Lubrication: ... Pressure and spinning

Engine oil: Filling quantity approx. 1,1 l

(if changed with filter)

Multi-grade oil

at ambient temperature -15° bis +45°C:

SAE 10W-40 API-SF, SG (or higher)

Operability on Slopes:

Engine is suited for use on slopes (with

oil level at “max” = upper level mark)

possible up to

20° inclination (37%)

Noise level:

Noise level

at operator’s ear ................. L

pA

= 88 dB

accordance with EN 836 appendix B and

EN ISO 3744

Acoustic power level: ...... L

WA

= 100 dB

accordance with EN 836 and EN ISO 11201

Vibration acceleration value:

Hand-arm vibration

on handlebar:.............. a

hw

= 1,48 m/s

2

in accordance with EN 836/A2 and DIN EN

ISO 20643

2

16 Brush Cutter 4500 Hydro

Petrol Engine for 85 cm

Manufacturer: .........Briggs & Stratton

Type: ..... Vanguard OHV 16HP V-Twin

................................................ 305700

Bore: ........................................ 68 mm

Stroke: ..................................... 66 mm

Cubic capacity: ................... 480 ccm

Output: ............ 11,9 kW (16 SAE-PS)

.........................................at 3600 rpm

Max torque:............................. 33 Nm

.........................................at 2400 rpm

Construction: ............. Fan-air-cooled

Spark ignition engine with overhead

valves, V-mounted double-cylinder and

vertically crankshaft

Spark plug: BOSCH FR8DC (706 09)

......................... CHAMPION RC12YC

Spark plug gap 0,76 mm

Ignition:

Electr. magnetic ignition, contactless

Radio remote screened ............ as per

VDE 0879

Valve clearance (engine cold):

Intake .................................... 0.05 mm

Outlet .................................... 0.10 mm

Fuel:....................................................

Commercial.........................................

.......................unleaded regular petrol

min. octane number 85 - 91 RON

(refer to fuel recommendations)

Fuel consumption:........... 312 g/kWh

Fuel filter:.......................... fuel-online

Air filter: .......... Dry filter element with

foamed preliminary filter

Carburettor: ....................... Horizontal

float carburettor

Rated speed: ...................... 3200 rpm

Top no-load speed: ............3350 rpm

Idling speed:.......................1750 rpm

Lubrication:

.. Pressure lubrication,full flow oil filter

Oil filter.......................... filter cartridge

Engine oil: Filling quantity approx. 1,6 l

(if changed with filter)

Multi-grade oil

at ambient temperature -15° bis +45°C:

SAE 10W-40 API-SF, SG (or higher)

Operability on Slopes:

Engine is suited for use on slopes (with

oil level at “max” = upper level mark)

possible up to

20° inclination (37%)

Noise level:

Noise level

at operator’s ear................. L

pA

= 89 dB

accordance with EN 836 appendix B and

EN ISO 3744

Acoustic power level: ...... L

WA

= 101 dB

accordance with EN 836 and EN ISO 11201

Vibration acceleration value:

Hand-arm vibration

on handlebar:................ a

hw

= 3,4 m/s

2

in accordance with EN 836/A2 and DIN EN

ISO 20643

2. Specifications

Brush Cutter 4500 Hydro 17

The brush cutter agria 4500 Hydro is sui-

ted for use in farming and forestry as

well as grass maintenance, such as for

example the mowing of grass and mea-

dows.

Engine

l

The four-stroke petrol engine runs

on commercial unleaded petrol (refer to

fuel recommendations page 6).

During the first 20 operating hours

(break-in period) do not use engine to

maximum power.

Even after break-in period never use

engine at higher speed than necessary

for the work in hand.

I

High engine speed is harm-

ful to any engine and consid-

erably affects its durability. This app-

lies especially for no load operation.

Any overspeed (have the engine roar)

can result in immediate damage.

Ignition System

The petrol engine is equipped with a

contactless ignition system. We recom-

mend to have necessary check-ups

done by an expert only.

Cooling System

The cooling system is fan-cooled. The-

refore keep screen at recoil starter and

cooling fins of cylinder clean and free

from sucked-in plant trash.

Idling-speed

Always ensure that idling-speed is ad-

justed correctly. At low speeds and with

the speed control lever set to idle, the

engine is supposed to run smoothly and

without run-out.

Air Filter

The air filter purifies the air intake. A

clogged filter reduces engine output.

3. Devices and Operating Elements

18 Brush Cutter 4500 Hydro

A/26

min

max

Version 4500 021

71 cm

Speed adjusting lever

The lever (A/26) is used in the illustra-

ted positions for the following:

- Switching engine OFF

- Engine speed stepless

from min. to max.

- Choke, for engine cold starts

Version 4500 031

85 cm

Choke

- for engine cold starts

- operating position

Engine Shut-off switch

0 = Off - engine shut off

I = Operating position

Speed adjusting lever

The lever (A/26) is used in the illustra-

ted positions for the following:

- Engine speed stepless

from min. to max.

A/25

A/26

min

max

3. Devices and Operating Elements

B/14

Brush Cutter 4500 Hydro 19

3

3. Devices and Operating Elements

Safety circuit

Engine shutt-off position "0" (both le-

vers not pressed).

Operating position (at least one lever

pressed down and held)

W

Do not fasten safety circuit lever

I

Release the safety circuit lever in an

emergency, the lever will auto-

matically go to STOP position!

A/30

20 Brush Cutter 4500 Hydro

Transmission

The agria brush cutter is equipped with a

hydrostatic drive.

Driving Control

l

The driving speed forward or reverse is

steplessly set or changed with the forefin-

ger or the thumb at the driving lever (A/27).

l

The 0 setting is engaged when the mar-

king on the driving lever is level with the

"0" in the illustration and hits the the spring

catch.

l

When turning the driving lever forwards,

the driving speed is steplessly increased

forwards and accordingly backwards, if the

driving lever is turned backwards and

down.

I

The engine can only be started

if the driving switch is set to

"0"!

Mulching Drive

The mulching drive is switched on and off

by using the excentric lever (A/24)

switch on

Swing the eccentric lever (A/24) back and

over dead centre.

switch on

Swing the eccentric lever (A/24) down.

A/27

3. Devices and Operating Elements

A/24

I

The engine can only be started if the driving switch and mulching

drive is set to "0" and both steering levers are set to "park brake"

and are locked into place!

-Safety circuit!

La pagina sta caricando ...

Agria 4500 Manuale del proprietario

Agria 4500 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti