Sony Computer Monitor CPD-520GST Manuale utente

Trinitron



Color

Computer Display

3-864-132-41 (1)

FR

CPD-520GST

DE

ES

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

Instruzioni per l’uso

GB

IT

2

Owner’s Record

The model and serial numbers are located at the rear of the unit.

Record the serial number in the space provided below. Refer to

these numbers whenever you call upon your dealer regarding this

product.

Model No. Serial No.

WARNING

To prevent fire or shock hazard, do not expose

the unit to rain or moisture.

Dangerously high voltages are present inside

the unit. Do not open the cabinet. Refer servicing

to qualified personnel only.

FCC Notice

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

INFORMATION

This product complies with Swedish National Council for

Metrology (MPR) standards issued in December 1990 (MPR II) for

very low frequency (VLF) and extremely low frequency (ELF).

INFORMATION

Ce produit est conforme aux normes du Swedish National Council

for Metrology de décembre 1990 (MPR II) en ce qui concerne les

fréquences très basses (VLF) et extrêmement basses (ELF).

Hinweis

Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency)

und tiefstfrequenter (extremely low frequency) Strahlung die

Vorschriften des „Swedish National Council for Metrology (MPR)“

vom Dezember 1990 (MPR II).

INFORMACIÓN

Este producto cumple las normas del Consejo Nacional Sueco para

Metrología (MPR) emitidas en diciembre de 1990 (MPR II) para

frecuencias muy bajas (VLF) y frecuencias extremadamente bajas

(ELF).

Dieses Garät entspricht den folgenden europäischen EMV-

Vorschriften für Betrieb in Wohngebieten, gewerblicher Gebleten

und Leichtindustriegebieten.

EN55022/1994 Klasse B

EN50082-1/1992

EN61000-3-2/1995

Hinweise

• Aus ergonomischen Gründen wird empfohlen, die

Grundfarbe Blau nicht auf dunklem Untergrund zu

verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu

geringem Zeichenkontrast).

• Aus ergonomischen Gründen (flimmern) sollten nur

Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne

Zeilensprung) verwendet werden.

• Die Konvergenz des Bildes kann sich auf Grund des

Magnetfeldes am Ort der Aufstellung aus der korrekten

Grundeinstellung verändern. Zur Korrektur empfiehlt es sich

deshalb, die Regler an der Frontseite für Konvergenz so

einzustellen, daß die getrennt sichtbaren Farblinien für Rot,

Grün und Blau bei z.B. der Darstellung eines Buchstabens zur

Deckung (Konvergenz) gelangen.

Siehe hierzu auch die Erklärungen zu Konvergenz.

NOTICE

This notice is applicable for USA/Canada only.

If shipped to USA/Canada, install only a UL LISTED/CSA

LABELLED power supply cord meeting the following

specifications:

SPECIFICATIONS

Plug Type Nema-Plug 5-15p

Cord Type SVT or SJT, minimum 3 × 18 AWG

Length Maximum 15 feet

Rating Minimum 7 A, 125 V

NOTICE

Cette notice s’applique aux Etats-Unis et au Canada

uniquement.

Si cet appareil est exporté aux Etats-Unis ou au Canada,

utiliser le cordon d’alimentation portant la mention UL

LISTED/CSA LABELLED et remplissant les conditions

suivantes:

SPECIFICATIONS

Type de fiche Fiche Nema 5-15 broches

Cordon Type SVT ou SJT, minimum 3 × 18 AWG

Longueur Maximum 15 pieds

Tension Minimum 7 A, 125 V

As an ENERGY STAR Partner, Sony

Corporation has determined that this

product meets the ENERGY STAR

guidelines for energy efficiency.

This monitor complies with the

TCO‘95 guidelines.

3

Getting Started

FR

GB

DE

ES

IT

TABLE OF CONTENTS

• Macintosh is a trademark licensed to Apple Computer, Inc., registered

in the U.S.A. and other countries.

• Windows

®

and MS-DOS are registered trademarks of Microsoft

Corporation in the United States and other countries.

• IBM PC/AT and VGA are registered trademarks of IBM Corporation of

the U.S.A.

• VESA is a trademark of Video Electronics Standard Association.

• ENERGY STAR is U.S. registered mark.

• All other product names mentioned herein may be the trademarks or

registered trademarks of their respective companies.

• Furthermore, “™” and “®" are not mentioned in each case in this

manual.

Getting Started

Precautions ........................................................................................................................... 4

Identifying Parts and Controls .......................................................................................... 5

Setup ...................................................................................................................................... 6

Automatically Adjusting the Size and Centering of the Picture................................... 7

Selecting the On-screen Display Language ..................................................................... 7

Selecting the Input Signal ................................................................................................... 8

Customizing Your Monitor

Adjusting the Picture Brightness and Contrast ............................................................... 9

Introducing the On-screen Display System ..................................................................... 9

Using the CENTER On-screen Display .......................................................................... 10

Using the SIZE On-screen Display .................................................................................. 10

Using the GEOM (Geometry) On-screen Display......................................................... 11

Using the ZOOM On-screen Display .............................................................................. 12

Using the COLOR On-screen Display ............................................................................ 12

Using the SCREEN On-screen Display........................................................................... 13

Using the OPTION On-screen Display........................................................................... 15

Using the LANG (Language) On-screen Display ......................................................... 17

Resetting the Adjustments ............................................................................................... 17

Technical Features

Preset and User Modes ..................................................................................................... 18

Power Saving Function ..................................................................................................... 19

Displaying the Monitor’s Information Box .................................................................... 19

Damper Wires .................................................................................................................... 19

Plug & Play ......................................................................................................................... 19

Additional Information

Warning Messages ............................................................................................................. 20

Troubleshooting ................................................................................................................. 20

Self-diagnosis Function ..................................................................................................... 22

Specifications ...................................................................................................................... 22

Appendix

TCO’95 Eco-document ......................................................................................................... i

“Blue Angel” Environmental Statement ......................................................................... iii

4

Getting Started

Warning on power connection

• Use an appropriate power cord for your local power

supply.

For the customers in the UK

If you use the monitor in the UK, please use the supplied

UK cable with the UK plug.

Examples of plug types

• Before disconnecting the power cord, wait at least 30

seconds after turning off the power to allow the static

electricity on the CRT display surface to discharge.

• After the power has been turned on, the CRT is

demagnetized (degaussed) for about 3 seconds. This

generates a strong magnetic field around the metal frame,

which may affect the data stored on magnetic tapes and

disks near the bezel. Place magnetic recording equipment,

tapes and disks away from this monitor.

The outlet should be installed near the equipment

and be easily accessible.

Precautions

Installation

• Prevent internal heat build-up by allowing adequate air

circulation. Do not place the monitor on surfaces (rugs,

blankets, etc.) or near materials (curtains, draperies) that

may block the ventilation holes.

• Do not install the monitor near heat sources such as

radiators or air ducts, or in a place subject to direct

sunlight, excessive dust, mechanical vibration or shock.

• Do not place the monitor near equipment which generates

magnetism, such as a transformer or high voltage power

lines.

Maintenance

• Clean the cabinet, panel and controls with a soft cloth

lightly moistened with a mild detergent solution. Do not

use any type of abrasive pad, scouring powder or solvent,

such as alcohol or benzine.

• Do not rub, touch, or tap the surface of the screen with

sharp or abrasive items such as a ballpoint pen or

screwdriver. This type of contact may result in a scratched

picture tube.

• Clean the screen with a soft cloth. If you use a glass

cleaning liquid, do not use any type of cleaner containing

an anti-static solution or similar additive as this may

scratch the screen’s coating.

Transportation

When you transport this monitor for repair or shipment, use

the original carton and packing materials.

Use of the Tilt-Swivel

With the tilt-swivel, this monitor can be adjusted to the

desired angle within 180° horizontally and 20° vertically.

To turn the monitor vertically and horizontally, hold it at

the bottom with both hands as illustrated below.

Getting Started

90°

15°

5°

for 100 to 120 V AC for 200 to 240 V AC

for 240 V AC only

5

Getting Started

FR

GB

DE

ES

Identifying Parts and Controls

See the pages in parentheses for further details.

Front

1 RESET (reset) button (page 17)

Resets the adjustments to the factory settings.

2 ASC (auto sizing and centering) button

(page 7)

Automatically adjusts the size and centering of the

images.

3 INPUT (input) button and HD15/BNC

indicators (page 8)

Selects the HD15 or 5BNC video input signal. Each time

you press this button, the input signal and

corresponding indicator alternate.

4 MENU (menu) button (pages 8 -17, 19)

Displays the MENU OSD.

5 > (contrast) (?//) buttons (pages 8 – 17,

22)

Adjust the contrast.

Function as the (?//) buttons when adjusting other

items.

6 ¨ (brightness) (./>) buttons (pages 8 –

17)

Adjust the picture brightness.

Function as the (./>) buttons when adjusting other

items.

7 u (power) switch and indicator (pages 19,

22)

Turns the monitor on or off.

The indicator lights up in green when the monitor is

turned on, and either flashes in green and orange or

lights up in orange when the monitor is in power

saving mode.

Pin No.

1

2

3

4

5

6

7

Pin No.

8

9

10

11

12

13

14

15

Rear

8 AC IN connector

Provides AC power to the monitor.

9 Video input 1 connector (HD15)

Inputs RGB video signals (0.700 Vp-p, positive) and

SYNC signals.

* Display Data Channel (DDC) Standard of VESA

!º Video input 2 connector (5 BNC)

Inputs RGB video signals (0.700 Vp-p, positive) and

SYNC signals.

Signal

Red

Green

(Composite

Sync on Green)

Blue

ID (Ground)

DDC Ground*

Red Ground

Green Ground

Signal

Blue Ground

DDC + 5V*

Ground

ID (Ground)

Bi-Directional

Data (SDA)*

H. Sync

V. Sync

Data Clock(SCL)*

5 4 3 2

1

678910

1112131415



6

Getting Started



to HD15

to video output

to VIDEO IN R/G/B

Connect to the computer in

the same way as for the HD15

connector.

If your PC system is not compatible with DDC2AB

and DDC2B+

This monitor uses the No. 9 pin in the video signal connector for

DDC2AB and DDC2B+ compatibility.

Some PC systems which are not compatible with either DDC2AB or

DDC2B+ may not accept the No. 9 pin. If you are not sure whether

your PC system accepts the No. 9 pin or not, use the HD15 (Female)

- HD15 (Male without the No. 9 pin) adapter (not supplied). Make

sure the male side (without the No. 9 pin) is connected to the

computer.

Connecting to a Macintosh or compatible

computer

About the supplied Macintosh adapter

The supplied Macintosh adapter is compatible with Macintosh LC,

Performa, Quadra, Power Macintosh and Power Macintosh G3

series computers.

Macintosh II series and some older versions of Power Book models

may need an adapter with micro switches (not supplied).

Connecting to the 5 BNC connectors

To connect the 5 BNC connectors, use the SMF-400 video

signal cable (sold separately). Connect the cables from left to

right in the following order: Red–Green–Blue–HD–VD.

Notes

• Do not short the pins of the video signal cable.

• The DDC standard does not apply to the 5 BNC connectors. If

you use the DDC standard, connect the HD15 connector to the

computer with the supplied video signal cable.

HD15 - HD15 adapter

(not supplied)∗

Macintosh adapter

(supplied)

IBM PC/AT or

compatible

computer

HD15 video

signal cable

(supplied)

Macintosh or

compatible

computer

HD15 video

signal cable

(supplied)

to SYNC IN HD/VD

to HD15

Setup

Before using this monitor, check that the following items are

included in your carton:

• Monitor (1)

• Power cord (1)

• HD15 video signal cable (1)

• Macintosh adapter (1)

• Windows Monitor Information Disk (1)

• Warranty card (1)

• Notes on cleaning the screen’s surface (1)

• These operating instructions (1)

This monitor works with any IBM or compatible system

equipped with VGA or greater graphics capability.

Although this monitor works with other platforms running

at horizontal frequencies between 30 and 96 kHz, including

Macintosh and Power Macintosh systems, a cable adapter is

required. Please consult your dealer for advice on which

adapter is suitable for your needs.

Step 1: Connect the monitor to the

computer

With the computer switched off, connect the video signal

cable to the monitor using the supplied HD15 video signal

cable.

• If you are using an IBM PC/AT or compatible computer,

refer to the section below.

• If you are using a Macintosh or compatible computer,

refer to the following section, “Connecting to a Macintosh

or compatible computer.”

• If you want to use the 5 BNC connectors, refer to the

section, “Connecting to the 5 BNC connectors.”

Connecting to an IBM PC/AT or compatible

computer

* The HD15 - HD15 adapter may be needed for some models.



7

Getting Started

FR

GB

DE

ES

to a power outlet

Power cord (supplied)

Automatically Adjusting the Size

and Centering of the Picture

By pressing the auto sizing and centering (ASC) button, the

size and centering of the picture are automatically adjusted

to fit the screen.

1 Turn on the monitor and computer.

2 Press the ASC button.

The picture is adjusted to fit the center of the screen.

Notes

• This function is intended for use with a computer running

Windows or similar graphic user interface software that

provides a full-screen picture. It may not work properly if the

background color is dark or if the input picture does not fill the

screen to the edges (such as an MS-DOS prompt).

• The screen may go blank for a few seconds while performing the

auto-sizing function. This is not a malfunction.

• Although the signals for picture aspect ratio 5:4 (resolution: 1280

× 1024) do not fill the screen to the edges, the picture is

accurately displayed.

Selecting the On-screen Display

Language

If you need to change the OSD language, see “Using the

LANG (Language) On-screen Display” on page 17.

The default setting is English.

Step 2: Connect the power cord

With the monitor switched off, connect one end of the

power cord to the monitor and the other end to a power

outlet.

Step 3: Turn on the monitor and computer

The installation of your monitor is complete.

Note

If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on

the screen, see “Warning Messages” on page 20.

For customers using Windows 95/98

To maximize the potential of your monitor, install the new model

information file from the supplied Windows Monitor Information

Disk onto your PC.

This monitor complies with the “VESA DDC” Plug & Play

standard. If your PC/graphics board complies with DDC, select

“Plug & Play Monitor (VESA DDC)” or this monitor’s model name

as the monitor type in the “Control Panel” of Windows 95/98.

If your PC/graphics board has difficulty communicating with this

monitor, load the Windows Monitor Information Disk and select

this monitor’s model name as the monitor type.

For customers using Windows NT4.0

Monitor setup in Windows NT4.0 is different from Windows 95/98

and does not involve the selection of monitor type. Refer to the

Windows NT4.0 instruction manual for further details on adjusting

the resolution, refresh rate, and number of colors.

ASC

to AC IN



8

Getting Started

Selecting the Input Signal

This monitor has two signal input connectors (HD15 and

5BNC) and can be connected to two computers. When the

power of both computers is on, select the input signal you

want to view as follows.

1 Turn on the monitor and both computers.

2 Press the INPUT button to select the HD15 or 5BNC

input signal.

Each time you press the INPUT button, the input signal

and corresponding indicator alternate.

Selecting the INPUT signal mode

This monitor has two modes of input signal selection,

“AUTO” and “MANUAL.”

When “AUTO” is selected

If no signal is input from the selected connector, the monitor

automatically selects the other connector’s signal. When you

restart the computer you want to view, or that computer is

in power saving mode, the monitor may automatically

select the other connector’s signal. This is because the

monitor switches from the interrupted signal to the constant

signal. If this happens, manually select the desired signal

using the INPUT button.

When “MANUAL” is selected

Even if no signal is input from the selected connector, the

monitor does not select the other connector’s signal.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

3 Press the ¨./> buttons to select “ (INPUT).”

4 Press the >?// buttons to select “AUTO” or

“MANUAL.”

The OPTION OSD automatically disappears after about 30

seconds.

To close the OSD, press the MENU button again.

For more information on using the OSD, see “Introducing

the On-screen Display System” on page 9.

HD15 BNC

INPUT

MENU

EXIT

CENTER

SIZE

GEOM

COLOR

LANG

ZOOM

SCREEN

OPTION

OK

MENU

ON

MANUAL DEGAUSS

UNLOCK

1 MIN

OPTION

ZZ...

AUTO

ZZ...

INPUT

1 MIN

OPTION

UNLOCK

MANUAL

9

Getting Started

Customizing Your Monitor

FR

GB

DE

ES

Horizontal

Frequency*

Vertical

Frequency*

Before adjusting

• Connect the monitor and the computer, and turn them on.

• Select “

LANG” in the MENU OSD, then select

“ENGLISH” (see page 17).

Adjusting the Picture Brightness

and Contrast

Once the setting is adjusted, it will be stored in memory for

all input signals received.

1 Press the ¨ (brightness) ./> or > (contrast) ?//

buttons.

The BRIGHTNESS/CONTRAST OSD appears.

2 For brightness adjustment

Press the ¨./> buttons.

> . . . for more brightness

. . . . for less brightness

For contrast adjustment

Press the >?// buttons.

/ . . . for more contrast

? . . . for less contrast

The OSD automatically disappears after about 3 seconds.

To reset, press the RESET button while the OSD is on. The

brightness and contrast are both reset to the factory settings.

* The horizontal and vertical frequencies for the received input

signal appear in the BRIGHTNESS/CONTRAST OSD.

Customizing Your Monitor

BRIGHTNESS/CONTRAST

26 26

80.0kHz/ 75Hz

Introducing the On-screen

Display System

Most adjustments are made using the MENU OSD.

MENU OSD

Press the MENU button to display the MENU OSD.

This MENU OSD contains links to the other OSDs described

below.

1 COLOR

Displays the COLOR OSD for adjusting the color

temperature.

2 CENTER

Displays the CENTER OSD for adjusting the centering

of the picture.

3 SCREEN

Displays the SCREEN OSD for adjusting the vertical

and horizontal convergence, etc.

4 ZOOM

Displays the ZOOM OSD for enlarging and reducing

the picture.

5 OPTION

Displays the OPTION OSD for adjusting the OSD

position and degaussing the screen, etc.

6 SIZE

Displays the SIZE OSD for adjusting the picture size.

7 LANG

Displays the LANGUAGE OSD for selecting the

language.

8 GEOM

Displays the GEOMETRY OSD for adjusting the picture

rotation and pincushion, etc.

9 EXIT

Closes the MENU OSD.

MENU

EXIT

CENTER

SIZE

GEOM

COLOR

LANG

ZOOM

SCREEN

OPTION

OK

MENU

10

Customizing Your Monitor

Using the CENTER On-screen

Display

The CENTER settings allow you to adjust the centering of

the picture.

Once the setting is adjusted, it will be stored in memory for

the current input signal.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

CENTER,” and press the MENU button again.

The CENTER OSD appears.

3 For horizontal adjustment

Press the >?// buttons.

/ . . . to move the picture right

? . . . to move the picture left

For vertical adjustment

Press the ¨./> buttons.

> . . . to move the picture up

. . . . to move the picture down

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The horizontal and vertical centerings are both reset to the

factory settings.

Using the SIZE On-screen Display

The SIZE settings allow you to adjust the size of the picture.

Once the setting is adjusted, it will be stored in memory for

the current input signal.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

SIZE,” and press the MENU button again.

The SIZE OSD appears.

3 For horizontal adjustment

Press the >?// buttons.

/ . . . to increase picture size

? . . . to decrease picture size

For vertical adjustment

Press the ¨./> buttons.

> . . . to increase picture size

. . . . to decrease picture size

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The horizontal and vertical sizes are both reset to the factory

settings.

MENU

SIZE

26

73

CENTER

26

73

11

Getting Started

Customizing Your Monitor

FR

GB

DE

ES

Using the GEOM (Geometry) On-

screen Display

The GEOM (geometry) settings allow you to adjust the

shape and orientation of the picture.

Once the rotation is adjusted, it will be stored in memory for

all input signals received. All other adjustments will be

stored in memory for the current input signal.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

GEOM,” and press the MENU button again.

The GEOMETRY OSD appears.

3 Press the ¨./> buttons to select the item you want

to adjust.

Select

ROTATION

PINCUSHION

PIN BALANCE

KEYSTONE

KEY BALANCE

To

adjust the picture rotation

adjust the picture sides

adjust the picture side balance

adjust the picture width

adjust the picture shape balance

MENU

ROTATION

GEOMETRY

26

4 Press the >?// buttons to adjust the settings.

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The selected item is reset to the factory setting.

For

ROTATION

PINCUSHION

PIN BALANCE

KEYSTONE

KEY BALANCE

Press

/ . . . to rotate the picture clockwise

? . . . to rotate the picture counterclockwise

/ . . . to expand the picture sides

? . . . to contract the picture sides

/ . . . to move the picture sides to the right

? . . . to move the picture sides to the left

/ . . . to increase the picture width at the

top

? . . . to decrease the picture width at the

top

/ . . . to move the top of the picture to

the right

? . . . to move the top of the picture to

the left

12

Customizing Your Monitor

Using the COLOR On-screen Display

You can change the monitor’s color temperature. For

example, you can adjust or change the colors of a picture on

the screen to match the actual colors of the printed picture.

Once the setting is adjusted, it will be stored in memory for

all input signals received.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

COLOR,” and press the MENU button again.

The COLOR OSD appears.

3 Press the >?// buttons to select the color

temperature.

There are three color temperature modes in the OSD.

The preset adjustments are:

5000K, 6500K, 9300K

MENU

Using the ZOOM On-screen

Display

The ZOOM settings allow you to enlarge or reduce the

picture.

Once the setting is adjusted, it will be stored in memory for

the current input signal.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

ZOOM,” and press the MENU button again.

The ZOOM OSD appears.

3 Press the >?//buttons to adjust the picture zoom.

/ . . . to enlarge the picture

? . . . to reduce the picture

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

Note

The picture zoom adjustment will stop as soon as either the

horizontal or vertical size reaches its maximum or minimum value.

MENU

ZOOM

73V

26H

5000K 6500K 9300K

G

COLOR

50

R

50

B

50

13

Getting Started

FR

GB

DE

ES

Customizing Your Monitor

Using the SCREEN On-screen

Display

You can adjust convergence settings to eliminate red or blue

shadows that may appear around objects on the screen.

Adjust the CANCEL MOIRE function to eliminate wavy or

elliptical patterns that may appear on the screen.

Adjust the LANDING function to correct color imbalances

at the four corners of the screen due to influence from the

earth’s magnetism.

Once CANCEL MOIRE is adjusted, it will be stored in

memory for the current input signal. All other adjustments

will be stored in memory for all input signals received.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

SCREEN,” and press the MENU button again.

The SCREEN OSD appears.

3 Press the ¨./> buttons to select the item you want

to adjust.

MENU

Select

H CONVERGENCE

V CONVERGENCE

TOP

V CONVER TOP

BOT

V CONVER BOTTOM

To

adjust the horizontal convergence

adjust the vertical convergence

adjust the screen’s upper vertical

convergence

adjust the screen’s lower vertical

convergence

(continued)

SCREEN

TOP

BOT

H CONVERGENCE

26

ADJ

4 Fine tuning the color temperature

Press the ¨./> buttons to select R (red), G (green), or B

(blue) and adjust by pressing the >?// buttons.

The “5000K,” “6500K” or “9300K” disappears and the

new color settings are memorized for each of the three

color modes.

The color temperature modes change as follows:

5000Kn 1, 6500Kn 2, 9300Kn 3

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on. The

selected item is reset to the factory settings.

1 6500K 9300K

G

COLOR

50

R

76

B

50

14

Customizing Your Monitor

* Moire is a type of natural interference which produces soft or

wavy lines on your screen. It may appear due to interference

between the regulated pattern of the picture from the input

signal and the phosphor pitch pattern of the CRT.

Example of moire:

4 Press the >?// buttons to adjust the settings.

Note

The picture may become fuzzy when CANCEL MOIRE is set to

“ON.”

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The selected item is reset to the factory setting.

ON

OFF

ON

OFF

50

For

BOT

V CONVER BOTTOM

LANDING

ADJ

LANDING ADJUST

CANCEL MOIRE

ADJ

MOIRE ADJUST

Press

/ . . . to shift red shadows up and blue

shadows down

? . . . to shift red shadows down and

blue shadows up

/ or ? . . . to select the corner of the

screen you want to adjust

: top left : top right

: bottom left : bottom right

/ or ? . . . to reduce any irregularities in

the color to a minimum

/ . . . to turn CANCEL MOIRE “ON”

? . . . to turn CANCEL MOIRE “OFF”

/ or ? . . . to adjust the screen until the

moire is at a minimum

Select

LANDING

ADJ

LANDING ADJUST

CANCEL MOIRE *

ADJ

MOIRE ADJUST

To

select one of the four corners that

needs color correction due to

influence from the earth’s magnetism

correct the color at one of the four

corners of the screen

turn the moire cancellation function

“ON” or “OFF.” CANCEL MOIRE

must be “ON” for “ ADJ (MOIRE

ADJUST)” to appear on the screen.

adjust the degree of moire

cancellation

For

H CONVERGENCE

V CONVERGENCE

TOP

V CONVER TOP

Press

/ . . . to shift red shadows to the right

and blue shadows to the left

? . . . to shift red shadows to the left

and blue shadows to the right

/ . . . to shift red shadows up and blue

shadows down

? . . . to shift red shadows down and

blue shadows up

/ . . . to shift red shadows up and blue

shadows down

? . . . to shift red shadows down and

blue shadows up

50

15

Getting Started

Customizing Your Monitor

FR

GB

DE

ES

Using the OPTION On-screen

Display

The OPTION OSD allows you to manually degauss the

screen and adjust settings such as the OSD position and

power saving delay time. It also allows you to lock the

controls.

Degaussing the screen

The monitor screen is automatically degaussed

(demagnetized) when the power is turned on.

You can also manually degauss the monitor.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

3 Press the ¨./> buttons to select “ (MANUAL

DEGAUSS).”

4 Press the > / button.

The screen is degaussed for about 3 seconds.

If you need to degauss the screen a second time, wait for at

least 20 minutes before repeating the steps above.

The OPTION OSD automatically disappears after about 30

seconds.

To close the OSD, press the MENU button again.

Changing the on-screen display position

You can change the OSD position (for example, when you

want to adjust the picture behind the OSD).

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

3 Press the ¨./> buttons to select “ (OSD H

POSITION)” or “

(OSD V POSITION).”

Select “

(OSD H POSITION)” to adjust the horizontal

position.

Select “

(OSD V POSITION)” to adjust the vertical

position.

4 Press the >?// buttons to move the OSD to the

desired position.

The OPTION OSD automatically disappears after about 30

seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

MENU

ON

MANUAL DEGAUSS

UNLOCK

1 MIN

OPTION

ZZ...

MENU

ON

MANUAL DEGAUSS

UNLOCK

1 MIN

OPTION

ZZ...

OSD H POSITION

UNLOCK

1 MIN

OPTION

ZZ...

OSD V POSITION

UNLOCK

OPTION

AUTO

16

Customizing Your Monitor

Locking the controls

The control lock function disables all of the buttons on the

front panel except the u (power) switch and MENU button.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

3 Press the ¨./> buttons to select “ (CONTROL

LOCK).”

4 Press the >?// buttons to select “LOCK.”

The OPTION OSD automatically disappears after about 30

seconds.

To close the OSD, press the MENU button again.

Once you select “LOCK,” you cannot select any items

except “EXIT” and “

OPTION” in the MENU OSD.

If you press any button other than the u (power) switch and

MENU button, the

mark appears on the screen.

To cancel the control lock

Repeat steps 1 through 3 above and press the >?//

buttons to select “UNLOCK.”

Setting the power saving delay time

You can set the delay time before the monitor enters the

power saving mode. See page 19 for more information on

this monitor’s power saving capabilities.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

3 Press the ¨./> buttons to select “

ZZ...

(PWR SAVE

DELAY).”

4 Press the >?// buttons to select the desired time.

When PWR SAVE DELAY is set to “OFF,” the monitor

does not go into power saving mode.

The OPTION OSD automatically disappears after about 30

seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

MENU

ON

MANUAL DEGAUSS

UNLOCK

1 MIN

OPTION

ZZ...

MENU

ON

MANUAL DEGAUSS

UNLOCK

1 MIN

OPTION

ZZ...

PWR SAVE DELAY

OPTION

5 SEC

60 MIN

1 MIN

OFF

AUTO

ZZ...

CONTROL LOCK

OPTION

UNLOCK LOCK

AUTO

17

Getting Started

Customizing Your Monitor

FR

GB

DE

ES

Using the LANG (Language) On-

screen Display

English, French, German, Spanish, Italian and Japanese

versions of the OSDs are available.

1 Press the MENU button.

The MENU OSD appears.

2 Press the ¨./> and >?// buttons to select “

LANG,” and press the MENU button again.

The LANGUAGE OSD appears.

3 Press the ¨./> buttons to select the desired

language.

ENGLISH: English, FRANÇAIS: French,

DEUTSCH: German, ESPAÑOL: Spanish,

ITALIANO: Italian, or

: Japanese.

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset to English, press the RESET button while the OSD

is on.

MENU

RESET

MENU

RESET

Resetting the Adjustments

Resetting an adjustment item

1 Press the MENU, ¨./> and >?//buttons to select

the OSD containing the item you want to reset.

2 Press the ¨./> buttons to select the item you want

to reset.

3 Press the RESET button.

Resetting all of the adjustment data for

the current input signal

When there is no OSD displayed, press the RESET

button.

All of the adjustments data for the current input signal is

reset to the factory settings.

Note that adjustment data not affected by changes in input

signal (OSD language, OSD position, input signal selection,

power saving delay time and the control lock function) is

not reset to the factory settings.

Resetting all of the adjustment data for all

input signals

Press and hold the RESET button for more than two

seconds.

All of the adjustment data, including the brightness and

contrast, is reset to the factory settings.

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

LANGUAGE

18

Technical Features

Preset and User Modes

This monitor has factory preset modes for the most popular

industry standards for true “plug and play” compatibility.

When a new input signal is entered, the monitor selects the

appropriate factory preset mode and momentarily adjusts

the phase calibration to provide a high quality picture to the

center of the screen. The calibration is stored in memory

and is immediately recalled whenever the same input signal

is received.

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

Resolution

(dots × lines)

640 × 350

640 × 480

720 × 400

800 × 600

832 × 624

1024 × 768

1152 × 864

1152 × 870

1280 × 960

1280 × 1024

1600 × 1200

Horizontal

Frequency

31.5 kHz

37.5 kHz

43.3 kHz

31.5 kHz

37.9 kHz

46.9 kHz

53.7 kHz

49.7 kHz

48.4 kHz

56.5 kHz

60.0 kHz

60.2 kHz

68.7 kHz

67.5 kHz

68.7 kHz

60.0 kHz

85.9 kHz

64.0 kHz

80.0 kHz

91.1 kHz

75.0 kHz

81.3 kHz

87.5 kHz

93.8 kHz

Vertical

Frequency

70 Hz

60 Hz

75 Hz

85 Hz

70 Hz

85 Hz

60 Hz

75 Hz

85 Hz

75 Hz

60 Hz

70 Hz

75 Hz

85 Hz

75 Hz

60 Hz

85 Hz

60 Hz

75 Hz

85 Hz

60 Hz

65 Hz

70 Hz

75 Hz

Graphics Mode

MCGA

VGA-G

EVGA

VESA

VGA-Text

VESA

SVGA

ESVGA

VESA

Macintosh

16” Color

VESA

EUVGA

Macintosh

19” Color

VESA

Macintosh

21” Color

VESA

Technical Features

For input signals that do not match one of the factory preset

modes, the digital Multiscan technology of this monitor

performs all of the adjustments necessary to ensure that a

clear picture appears on the screen for any timing in the

monitor’s frequency range. However, it may be necessary

to fine tune the vertical/horizontal size and centering.

Simply press the ASC button or adjust the monitor

according to the adjustment instructions. The adjustments

are stored automatically as a user mode and recalled

whenever the corresponding input signal is received.

Recommended horizontal and vertical timing

conditions

Horizontal sync width duty should be: >4.8% of total horizontal

time.

Horizontal blanking width should be: >2.8 µsec.

Vertical blanking width should be: > 450 µsec.

Note for Windows users

For Windows users, check your video board manual or the utility

program which comes with your graphic board and select the

highest available refresh rate to maximize monitor performance.

Adjusting the monitor’s resolution and color

number

Adjust the monitor’s resolution and color number by referring to

your computer’s instruction manual. The color number may vary

according to your computer or video board. The color palette

setting and the actual number of colors are as follows:

• High Color (16 bit) n 65,536 colors

• True Color (24 bit) n about 16.77 million colors

In true color mode (24 bit), speed may be slower.

19

Getting Started

Technical Features

FR

GB

DE

ES

Power Saving Function

This monitor meets the power-saving guidelines set by

VESA and

ENERGY STAR, as well as the more stringent

NUTEK .

If the monitor is connected to a computer or video graphics

board that is VESA DPMS (Display Power Management

Signaling) compliant, the monitor will automatically reduce

power consumption in three stages as shown below.

1

2

3

4

5

u indicator

Green

Green and orange

alternate

Green and orange

alternate

Orange

Off

Power consumption

mode

Normal operation

Standby (1st mode)

Suspend (2nd mode)

Active-off (3rd mode)

Power-off

Screen

active

blank

—

Horizontal

sync signal

present

absent

present

absent

—

Vertical

sync signal

present

absent

—

You can set the delay time before the monitor enters the

power saving mode using the OSD. Set the time according

to “Setting the power saving delay time” on page 16.

Note

If no video signal is input to the monitor, the “NO INPUT

SIGNAL” message (page 20) appears. After the delay time has

passed, the power saving function automatically puts the monitor

into the active-off mode and the u indicator lights up orange. Once

the horizontal and vertical sync signals are detected, the monitor

automatically resumes its normal operation mode.

Damper Wires

When viewing a white background, very thin horizontal lines

may be visible on the screen as shown below. These lines are

the shadows of the damper wires and are characteristic of

CRTs that use aperture grilles. The wires are attached to the

aperture grille on the inside of the Trinitron tube and prevent

the vibration of the aperture grille.

Damper wires

Plug & Play

This monitor complies with the DDC1, DDC2B, DDC2AB

and DDC2B+ Display Data Channel (DDC) standards of

VESA.

When a DDC1 host system is connected, the monitor

synchronizes with the V. CLK in accordance with the VESA

standards and outputs the EDID (Extended Display

Identification Data) to the data line.

When a DDC2B, DDC2AB or DDC2B+ host system is

connected, the monitor automatically switches to the

appropriate standard.

DDC is a trademark of the Video Electronics Standard

Association.

Note

When using Windows 95/98, the DDC standard does not apply to

the 5 BNC connectors. If you use the DDC standard, connect the

HD15 connector to the computer with the supplied video signal

cable.

Power consumption

≤ 145 W

Approx. 72 W

Approx. 7 W

Approx. 3 W

0 W

Recovery time

—

Approx. 3 sec.

Approx. 10 sec.

—

Displaying the Monitor’s

Information Box

You can display the model name, serial number and year of

manufacture using the monitor‘s INFORMATION OSD.

Press and hold the MENU button for 5 seconds.

The INFORMATION OSD appears.

Example:

The INFORMATION OSD includes the model name, serial

number, manufactured year, and manufactured week.

The OSD automatically disappears after about 30 seconds.

MENU

INFORMATION

SER NO

:

1234567

MODEL

:

CPD 520GST

MANUFACTURED

:1998 52

20

Additional Information

Warning Messages

If there is something wrong with the input signal, one of the

following messages appears.

Additional Information

1 The input signal condition

“OUT OF SCAN RANGE” indicates that the input signal

is not supported by the monitor’s specifications.

“NO INPUT SIGNAL” indicates that no signal is input, or

the input signal from the selected input connector is not

received.

2 The selected input connector

Indicates which input connector is receiving the wrong

signal. If there is something wrong with the signal from

both input connectors, “HD15” and “BNC” are

displayed alternately.

To solve these problems, see “Troubleshooting” below.

Troubleshooting

This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.

Symptom Check these items

No picture

If the u indicator is not lit

If the “NO INPUT SIGNAL”

message appears on the screen,

or if the u indicator is either

orange or alternating between

green and orange

If the “OUT OF SCAN RANGE”

message appears on the screen

If no message is displayed and

the u indicator is green or

flashing orange

If using a Macintosh system

If using Windows 95/98

Picture is scrambled

• Check that the power cord is properly connected.

• Check that the u (power) switch is in the “on” position.

• The screen is blank when the monitor is in power saving mode. Try pressing any key on the

computer keyboard.

• Check that your computer power switch is in the “on” position.

• Check that the input select setting is correct.

• Check that the video signal cable is properly connected and all plugs are firmly seated in

their sockets.

• Check that the 5 BNCs are connected in the correct order (from left to right: Red–Green–

Blue–HD–VD) (page 6).

• Ensure that no pins are bent or pushed in the HD15 video input connector.

• Check that the video board is completely seated in the proper bus slot.

• Check that the video frequency range is within that specified for the monitor.

Horizontal: 30 – 96 kHz, Vertical: 48 – 160 Hz

Refer to your computer’s instruction manual to adjust the video frequency range.

• If you are using a video signal cable adapter, check that it is correct.

• See “Self-diagnosis Function” (page 22).

• Check that the Macintosh adapter and the video signal cable are properly connected (page

6).

• If you replaced an old monitor with this monitor, reconnect the old monitor and do the

following. Install the Windows Monitor Information Disk (page 7) and select “CPD-

520GST” from among the Sony monitors in the Windows 95/98 monitor selection screen. If

you choose to select “Plug and Play,” connect the monitor to the computer with the HD15

video signal. You cannot use the five BNC connectors.

• Check your graphics board manual for the proper monitor setting.

• Check this manual and confirm that the graphics mode and the frequency you are trying to

operate at is supported. Even if the frequency is within the proper range, some video

boards may have a sync pulse that is too narrow for the monitor to sync correctly.

INFORMATION

OUT OF SCAN RANGE

INPUT : HD15

La pagina sta caricando ...

Sony Computer Monitor CPD-520GST Manuale utente

Questo manuale è adatto anche per

Sony Computer Monitor CPD-520GST Manuale utente

in altre lingue

Documenti correlati

Altri documenti