3
Bathys
Manuel d’utilisation / User manual
Bathys
Type Closed-back headphones, active, noise cancelling
Bluetooth® 5.1 Multipoint ; range > 15m
Bluetooth® frequency band 2404-2480Mhz
Maximum emission power 4.56dBm (2.86mW)
Audio codecs SBC, AAC, aptX™, aptX™ Adaptive
Autonomy
30h Bluetooth® Noise Cancelling
35h mode jack
42h mode USB DAC
Voice assistants Google Assistant, Amazon Alexa
Drivers 40mm Aluminium-Magnesium
Frequency response 15Hz to 22.1kHz
THD <0.2% @1kHz
Battery type Lithium-ion 1060mAH
Power supply 5V-2000mA (Not supplied)
Microphones 8
Control application Focal & Naim, iOS and Android compatible
Weight 350g
Cables and connectors 1.2m mini-jack
1.2m USB Type-C®
Carrying case 9.5x8.3x2.8" (24x21x7cm)
EN
READ THIS FIRST!
IMPORTANT SAFETY INSTRUCTIONS!
English
Warning symbol. This symbol is designed to warn the user of the presence
of important instructions mentioned in the user manual and relating to the
handling, operation and maintenance of the device.
Before using the product, read the
instructions and keep them carefully
for future reference if required.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings contained in
these instructions.
4) Follow all the instructions.
5) Listening to high powered
headphones can damage the ears and
lead to hearing problems (temporary
or permanent deafness, ringing in the
ears, tinnitus, hyperacusis).
(CEI 60417-6044)
Exposure to excessive
volumes (over 85 dB) for
more than one hour
can cause irreparable
damage to your hearing.
The headphones must, therefore, be
turned on before wearing them and
we strongly advise against using the
headphones at full volume, nor for
more than one hour a day at medium
volume.
Do not use the headphones
continuously; take regular breaks.
If you experience buzzing or ringing
(tinnitus) in the ears, hearing loss or
a “mued” sensation, stop listening
to the headphones immediately. If
symptoms persist after a few hours,
consult your doctor immediately who
will, if necessary, refer you to an ENT
specialist. In some cases, immediate
treatment can prevent irreversible
damage.
6) Always turn on the headphones
before wearing them, set the listening
device’s volume to the lowest setting
before connecting your headphones
and increasing the volume. Once the
headphones are in place, gradually
increase the volume to a reasonable
and comfortable level.
7) Never use the headphones without
the earpads or protective tips.
8) Be sure to use the headphones
in such a way that you can still hear
sounds around you. In particular, the
product’s active noise cancellation
may make ambient noise inaudible or
significantly change your perception
of warning signals; reducing the
chance of hearing ambient noise is a
risk for yourself and those around you.
Do not use the headphones in
conditions requiring special attention,
such as when outdoors in heavy
trac, near a construction site or a
railway line, etc.
Never drive a vehicle (car, motorcycle,
boat, electric scooter, etc.) or ride
a bicycle, skateboard, roller blades,
hoverboard, etc. while wearing the
headphones.
Any use under these circumstances
is dangerous and, in some countries,
illegal.
9) It is also not recommended to use
the headphones for running, walking
or doing any other activity in crowded
places. If you use the headphones
under these circumstances, set the
volume to low so that you can hear
ambient sounds, including horns,
alarms and warning signals.
10) Please ensure that children and
young people under the age of 14 are
not allowed to use the headphones
without supervision. Be particularly
vigilant with regard to children and
adolescents who often use these
devices at excessive volumes.
11) Do not use the headphones for
anything but their original function.
Never use headphones as a form
of noise protection. Do not use
the headphones as an aviation
communications headset.
12) Use compliant adapters to connect
your headphones to aeroplane seat
plugs. Failure to do so may result in
personal injury or property damage
caused by overheating.
13) If you feel heat or lose audio
signal, remove and disconnect the
headphones immediately.
14) Do not place burning objects near
and/or on the headphones, such as lit
candles, lighters, etc.
15) Do not apply any weight or
pressure to the headphones for too
long, including when turned o or
not in use.
16) Do not expose your headphones
to moisture or immerse them in water.
17) The headphones do not require
specific cleaning. If necessary, use a
soft, dry cloth. Do not use cleaning
products containing solvents.
18) Have any repairs or servicing
carried out by a professional. Such
operations are necessary in the event
of damage of any kind, such as liquid
spillage, cable damage, exposure to
rain, dropping the device, etc.
Do not modify the system or
its accessories. Unauthorised
modifications may compromise your
safety, regulatory compliance and
device performance.
If you replace your earpads, be
sure to replace them only with the
specific pad model provided by the
manufacturer so as not to aect
the sound quality and active noise
reduction.
19) This product poses risks of:
• choking;
• fire or electrocution (do not expose
the device to rain or moisture, or any
other liquid).
20) This product contains magnetic
components and generates
magnetic fields which may interfere
with pacemakers and implanted
defibrillators. Before using the
headphones, contact your GP if you
have any questions regarding the
eect of these components on the
functioning of an implanted medical
device.
21) This product
complies with
all applicable
European
regulations and directives. This symbol
means that the product (including its
battery if applicable) must not be
thrown away with household waste
but must be taken to an appropriate
collection centre for recycling. Proper
disposal and recycling helps protect
natural resources, human health and
the environment. For more
information on the disposal and
recycling of this product, contact your
local council, your waste collection
service or the store where you
purchased this product.
22) This product contains
a lithium-ion battery,
which should be
handled with care.
Lithium batteries can be dangerous if
not used and handled properly. In
extreme cases, abnormal use of
lithium batteries can lead to:
• explosion
• fire
• release of heat
• release of smoke or gas.
23) Caution, do not open the device.
It is forbidden to disassemble, open,
pierce, or perform any other action on
the battery on your own.
Caution, there is a danger of explosion
if the battery is incorrectly replaced.
Replacing and/or removing the
battery from your Focal product must
be carried out by a professional. The
battery must be replaced by a battery
identical to the original one and
obtained from a Focal dealer.
Focal cannot guarantee the safety
or compatibility of batteries from
other manufacturers, or that they will
function properly with the device.
EN
Warning symbol. This symbol is designed to warn the user of the presence
of important instructions mentioned in the user manual and relating to the
handling, operation and maintenance of the device.
Do not short-circuit the (+) and
(-) terminals of the battery with
conductive elements (in contact with
metallic objects in particular), or by
any other means.
Do not reverse the polarities.
Do not place burning objects near
and/or on the headphones’ built-in
battery. In general, the battery should
not be exposed to excessive heat
such as sunshine, fire or similar (above
70°C) and/or humidity above 90%.
Do not expose the battery and
charger to water (do not immerse,
pour liquid on them, expose to
condensation or get wet). Do not
expose to rain.
Never use a damaged battery.
Do not subject the battery to impacts
or vibrations. In the event of a severe
impact, stop using the battery.
Do not destroy or incinerate the
battery.
Exposure to internal battery
components or the products released
when burned can be hazardous. If you
have been exposed, contact your GP.
If, during use, the battery gives o an
unusual odour or becomes abnormally
hot or warped, switch o the device
immediately and contact your Focal
dealer.
Only use this product with a certified
Limited Power Supply (LPS) that
meets local regulatory requirements
(e.g. UL, CSA, VDE, CCC & CE).
Only charge the battery at an ambient
temperature between 0°C and 45°C.
Never charge a swollen, leaking or
otherwise damaged battery.
Never use a modified or damaged
charger. Only charge the battery
on non-flammable surfaces (do not
charge it on a flammable surface
such as carpet or wooden floors)
and do not charge it near flammable
materials. Charge the battery on a
non-conductive surface to prevent any
damage associated in particular with a
short circuit.
Keep the battery and charger out of
the reach of children under 14 years
old.
Do not use the headphones while the
battery is charging.
Any battery (original or replacement)
should not be exposed to heat such as
sunshine, fire or similar.
OPTIMAL CONDITIONS FOR
BATTERY USE
For your headphones’ battery to
retain optimal autonomy, and in the
event of prolonged non-use, recharge
it regularly and at least once every
three months or so.
Turn o battery-powered products
when not in use.
For optimal use, do not use
headphones with a battery in places
subject to excessive heat (above
40°C) or excessive cold (below -5°C).
In the event of a problem, contact
your specialist dealer.
- The replacement of a battery with an
incorrect type can defeat a safeguard
(for example, in the case of some
lithium battery types);
- the disposal of a battery into fire or
a hot oven, or mechanically crushing
or cutting of a battery can result in an
explosion;
- leaving a battery in an extremely
high temperature surrouding
environment can result in an explosion
or the leakage of flammable liquid
or gas;
- a battery subjected to extremely low
air pressure may result in an explosion
or the leakage of flammable liquid
or gas.
FCC Regulatory Compliance
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate the
equipment.
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant
to Part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment o and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving
antenna.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an
outlet on a circuit dierent from that
to which the receiver is connected.
- Consult the dealer or an experienced
radio/TV technician for help.
This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment. This
transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
ISED Regulatory Compliance
This device contains licence-exempt
transmitter(s)/receiver(s) that
comply with Innovation, Science and
Economic Development Canada’s
licence-exempt RSS(s). Operation
is subject to the following two
conditions: (1)This device may not
cause interference.(2)This device
must accept any interference,
including interference that may cause
undesired operation of the device.This
equipment complies with IC RSS-102
radiation exposure limits set forth for
an uncontrolled environment.
16
Bathys
EN
User manual
Thank you for purchasing a Focal product. Welcome to our High-Fidelity world. Innovation, tradition,
excellence and pleasure are our values; our one and only aim is to bring you a sound that is rich, pure and
true. To get the most out of your product, we recommend that you read the instructions in this booklet,
then store it in a safe place to refer to in the future.
1. Package contents
• 1 x Bathys headphones
• 1 x carrying case
• 1 x Jack cable
• 1 x USB-C® cable
• 1 x Quick Start
• 1 x Brand content
2. Application
The Focal app allows you to configure and control the headphones from your mobile device, including
via your smartphone.
Using the app, you can manage Bluetooth® connections, headphones settings and access any new features
added through updates (EQ).
For development purposes, FOCAL-JMLab reserves the right to modify the technical specifications of its products without prior notice.
Non-contractual images.
- Download the app
App Store
Google Store
- Follow the instructions in the app
To facilitate the Focal-JMlab warranty, it is now possible to register
your product online, at www.focal.com/warranty
17
Bathys
EN
User manual
3. Powering on - Powering off - Pairing
To turn on the headphones, slide the power button to ON.
To turn them off, return the button to the OFF position. If you stop using the headphones for longer than
15 minutes, in Bluetooth® mode, they will automatically enter standby. To turn back on from standby, press
the multifunction button.
The headphones can save up to 8 devices. When you turn them on, the headphones will attempt to connect
to one of the saved devices. To launch pairing with another device, press and hold the multifunction button
for 4 seconds; the logo will flash and a sound signal will be emitted. Go to the Bluetooth® settings on the
device to connect to the headphones. Once paired with the device, the headphones are ready to use.
4. Using the headphones in Bluetooth®, jack and USB DAC modes
a. Bluetooth®
To use the headphones in Bluetooth® mode, the power switch must be in the ON position. When using the
headphones for the first time, the pairing mode is automatically enabled. To connect to the device, go to
its Bluetooth® settings and connect it to the “Focal Bathys” headphones. Once the pairing is successful,
the headphones are ready to use.
To connect to another device, enable the pairing mode on the headphones by pressing and holding the
multifunction button for 4 seconds. The logo will flash and a sound signal will be emitted. Go into the
Bluetooth® settings for the device to connect the headphones. In free field, the Bluetooth® has a 16.4-yard
(15-metre) range. Beyond that distance, the headphones will disconnect from the source.
18
Bathys
EN
User manual
b. Jack
To use the headphones with the jack mode, you must use the jack cable supplied in the pack. Connect the
cable to the jack input on the right-hand earcup of the headphones. The power switch must be in the ON
position. When you connect the jack cable, the Bluetooth® function will disconnect.
If the cable is damaged, contact your dealer who will supply you with the spare parts you need.
c. USB DAC
To use the USB DAC mode, use the USB-C® cable supplied with the product and move the power switch
to the DAC position.
If the cable is damaged, contact your dealer who will supply you with the spare parts you need.
19
Bathys
EN
User manual
5. Playing multimedia - Volume
6. Charging the headphones
To charge the headphones, use the USB-C® supplied and connect it to the USB-C® input on the right-hand
earcup of the headphones. The power switch must be in either the OFF or ON position. The headphones
must be switched off while they are being charged.
If you use a USB AC adapter, it must have a 5-volt output and a 300mA current as a minimum.
The headphones come equipped with the fast charging feature. To use it, connect the device to a 2-amp
(2000mA) adapter.
15 minutes of fast charging will give you around 5 hours of additional listening time. It takes around
one and a half hours to fully charge the headphones (with 2 amps). With a full charge, you will have
approximately 30 hours of battery life.
The battery’s performance diminishes over time and the more times it is charged. The battery life, charging
time and fast-charging time shown are therefore likely to change.
During charging, the battery light will flash white. Once the battery is fully charged, the battery light will
stay white.
Play / pause Press the multifunction key
Next Press the multifunction key twice
Previous Press the multifunction key three times
Increase volume Press the + key
Reduce volume Press the - key
20
Bathys
EN
User manual
7. Active noise reduction - Transparency mode
To change the noise reduction mode or enable the transparency mode, press the button located on the
left-hand earcup of the headphones. Choose between noise reduction and transparency mode with a
short press. Change the noise reduction mode by pressing and holding for 2 seconds.
These modes can be changed using the app.
There are 2 noise reduction modes and one transparency mode.
- Silent: provides the highest level of noise reduction.
- Soft: reduces the lowest-frequency noises while allowing you to hear ambient noise.
- Transparency: allows you to hear ambient noise and have a conversation without removing the
headphones, while continuing to listen to your music.
If the headphones are used without music in the DAC position, the active noise reduction feature reduces
background noise. The noise reduction will work as long as there is battery. If the ON position is used, the
headphones will automatically enter standby after 15 minutes, which will switch off active noise reduction.
You should follow the same precautions relating to active noise reduction as when using the feature with
music.
8. Voice assistants
The headphones are compatible with the Google Assistant and Amazon Alexa voice assistants, as well as
the voice assistants on your devices. In the app, choose which voice assistant you want to use and connect
to the Google Assistant or Amazon Alexa account. To activate this feature, press the button on the right-
hand earcup of the headphones, and speak.
21
Bathys
EN
User manual
9. Telephone communications
If you receive a call while you are listening to music, the playback will pause and you will hear a ringtone
through the headphones. The headphones are fitted with microphones which use Clear Voice® technology.
To answer, press the multifunction button. To hang up, press this same button again. To reject the call,
press and hold on the multifunction button for 2 seconds.
10. Product lighting
The headphones are fitted with LEDs on the earcups. You can deactivate the use of different lights via the
app in Bluetooth® mode.
11. Connecting to several devices at the same time
The headphones are fitted with multipoint Bluetooth® technology which allows them to be connected to
two devices at the same time. The headphones can therefore switch easily between two audio sources
without using the normal process of Bluetooth® reconnection. The headphones can also automatically
answer a call on your phone when you are listening to audio content on another source (for example, a
computer or tablet).
The headphones can save up to 8 devices. If more than 8 different devices are connected, the device that
was paired first will be removed. You will need to pair it again. To do this, press and hold the multifunction
button for 4 seconds.
2s
x1 R
Feature Light behaviour
Searching for device LEDs flash
Pairing mode LEDs flash slowly
Connected LEDs light up
Battery charging USB LED flashes
Battery charged USB LED lights up
Jack mode LEDs light up 50%
USB-C® mode LEDs light up 50%
OFF LEDs switched off
22
Bathys
EN
User manual
12. Replacing the earpads
If your earpads show signs of wear, they are easy to replace: carefully pull on your earpads to detach the
6 clips.
When you are replacing the earpads, ensure that the clips are all correctly mounted so as not to alter
the sound quality and active noise reduction. They must be replaced with the same model. Contact your
dealer, who will be able to provide you with the spare parts you need.
13. Cleaning the headphones
You can clean the headphones by simply dusting with a soft, dry cloth. If there are any stains or marks on
the leather parts, contact a specialist as it is not advisable to clean this material yourself.
14. Storing the headphones
When you are not using the headphones, we recommend that you switch them off and store them flat in
their carrying case, turning the earcups to face inwards.
Fully charge the battery if you do not plan on using the headphones for several months. If the headphones
are not in use for a prolonged period, charge the battery fully every 3 months in order to preserve device
performance.
23
Bathys
EN
User manual
15. Firmware update
Use the app to update the firmware for the headphones, without which some of the device’s features will
no longer be available.
16. Restoring the factory settings - Forced shutdown
To restore the factory settings on the headphones, press and hold the “–” and “ANC” buttons at the same
time for 8 seconds. Everything saved on the headphones will be deleted.
To carry out a forced shutdown on the headphones, press the “+”, “-” and “ANC” buttons at the same time.
The latest settings used on the headphones will be stored.
17. Troubleshooting
If you encounter any difficulties when using the product, consult the frequently asked questions (FAQ) on
our website. If the problem persists, contact customer service.
18. Warranty
Outside France, Focal equipment is covered by a warranty for which the terms and conditions are
determined or implemented locally by the official Focal distributor for each country, in accordance with
the laws in force in the region in question.
134
Bathys
Déclaration conformité CE simplifiée avec renvoi vers le site internet
Focal JMLab déclare que ce produit est conforme aux critères essentiels et autres dispositions de la directive 2014/53/
UE et des autres directives européennes applicables. L’attestation complète de conformité est disponible à l’adresse :
https://eur-lex.europa.eu/legal-content/FR/TXT/PDF/?uri=CELEX:32014L0053&from=IT
Ce produit est conforme à toutes les réglementations de 2016 en matière de compatibilité électromagnétique et à toutes les
autres réglementations britanniques applicables. Focal JMLab déclare que ce produit est conforme aux critères essentiels
et autres dispositions des réglementations de 2017 sur les équipements radio et des autres réglementations britanniques
applicables.
https://www.focal.com/certifications/bathys
FCC et IC
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment .This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC and IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISED Regulatory Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not
cause interference.(2)This device must accept any interference, including interference that may cause undesired operation
of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
135
Bathys
Google and Google Play are
trademarks of Google LLC.
Amazon, Alexa, Echo, and all related
marks are trademarks of Amazon.
com, Inc. or its aliates. Alexa
is not available in all languages
and countries. Alexa features and
functionality may vary by location.
Qualcomm is a trademark of
Qualcomm Incorporated, registered in
the United States and other countries.
aptX is a trademark of Qualcomm
Technologies International, Ltd.,
registered in the United States and
other countries.
Qualcomm® aptX™ Adaptive audio
supports low-latency,
robust and high resolution Bluetooth
wireless audio.
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Focal is under license. Other
trademarks and trade names are those
of their respective owners.
Use of the Made for Apple badge
means that an accessory has been
designed to connect specifically to
the Apple product(s) identified in the
badge and has been certified by the
developer to meet Apple performance
standards. Apple is not responsible
for the operation of this device or its
compliance with safety and regulatory
standards.
Apple, Apple TV, Apple Watch,
iPad, iPad Air, iPad Pro, iPhone, and
Lightning are trademarks of Apple
Inc., registered in the U.S. and other
countries. tvOS is a trademark of
Apple Inc. The trademark “iPhone” is
used in Japan with a license from
Aiphone K.K.
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Operation Frequency: 2402MHz to 2480MHz
EIRP or emission
power (Max): 4.56dBm (2.86mW)
Markings related to country certifications and
manufacturer information are located under the
earpads. To access it, you need to remove the
earpads and lift the acoustic fabric.
Les marquages relatifs aux certifications pays et
information sur le fabricant se trouvent sous les
coussinets. Pour y accéder, vous devez enlever les
coussinets et soulever le tissu acoustique.
USB Type-C® and USB-C are registered
trademarks of USB Implementers Forum.
Atenção: conforme lei brasileira n° 11.291, a
exposição prolongada a ruídos superiores a 85dB
pode causar danos ao sistema auditivo. IFT ID:
EUFOBA22-16584 - Véase instructivo anexo
Imported in Mexico by EUROTRONICS SA DE CV,
GENERAL MARIANO ARISTA 54 INT. NAVE 10 col.
argentina poniente MIGUEL HIDALGO, CIUDAD
DE MÉXICO C.P.11230 - R.F.C. EUR100525NRA
Ok Google
136
Bathys
FR
Élimination correcte de ce produit.
Ce marquage indique que ce produit ne doit pas être éliminé avec les autres déchets ménagers
au sein de l’UE. Par mesure de prévention pour l'environnement et pour la santé humaine, veuillez
le recycler de manière responsable, pour favoriser la réutilisation des ressources matérielles. Pour
retourner votre appareil usé, veuillez utiliser les systèmes de retour et de collecte ou contactez
le détaillant chez lequel le produit a été acheté. Celui-ci pourra procéder au recyclage du produit
en toute sécurité
EN
Correct elimination of this product.
This marking indicates that within the EU this product should not be disposed of with other
household wastes. To prevent any risk to the environment or human health, please recycle them
responsibly to encourage the reuse of material resources. To return your used device, please
use the return and collection systems available, or contact the retailer where you purchased the
product. They can recycle this product safely.
DE
Ordnungsgemäße Entsorgung des Produkts.
Diese Kennzeichnung weist darauf hin, dass dieses Produkt innerhalb der EU nicht mit anderen
Haushaltsabfällen entsorgt werden darf.
Als Präventivmaßnahme für die Umwelt und die menschliche Gesundheit muss auf eine
verantwortungsbewusste Wiederverwertung zur Förderung der Wiederverwendung von
materiellen Ressourcen geachtet werden. Für die Rückgabe von Gebrauchtgeräten verwenden
Sie bitte zur Verfügung stehende Rückgabe- und Recyclingsysteme oder wenden Sie sich an
den Händler, bei dem Sie das Produkt erworben haben. Letzterer kann das Gerät sicher dem
Wertstoffkreislauf zuführen.
ES
Eliminación correcta de este producto.
Este símbolo indica que este producto no debe eliminarse con el resto de residuos domésticos
dentro de la UE. Con el objetivo de proteger el medioambiente y la salud pública, recicle de forma
responsable para favorecer la reutilización de los recursos materiales. Para devolver su aparato
usado, utilice los sistemas de devolución y recogida o póngase en contacto con el vendedor del
producto. Este podrá proceder al reciclaje del producto de forma totalmente segura.
IT
Corretto smaltimento di questo prodotto.
Questa marcatura indica che, nell'UE, questo prodotto non deve essere smaltito insieme agli
altri rifiuti domestici. A titolo preventivo per l'ambiente e la salute, deve essere riciclato in modo
responsabile per favorire il riutilizzo delle risorse materiali. Per mandare indietro l'apparecchio
usato, si prega di utilizzare il sistema di reso e raccolta o di contattare il rivenditore da cui è stato
acquistato il prodotto, il quale potrà procedere a riciclare il prodotto in totale sicurezza.
Focal-JMlab® - BP 374 - 108, rue de l'Avenir - 42353 La Talaudière cedex - France - www.focal.com
Tel. (+33) 04 77 43 57 00 - Fax (+33) 04 77 43 57 04 - SCCG - 03/11/2022 - v3
Bathys
Démarrage rapide / Quick Start
Accéder à la notice d’utilisation
Bedienungsanleitung lesen
Acceda a las instrucciones de uso
Accedi alle istruzioni per l’uso
Ir para o manual do utilizador
Ga naar de gebruiksaanwijzing
Przejdź do instrukcji obsługi
Перейти к инструкции по эксплуатации
访问使用说明
訪問用戶指南
사용설명서 보러가기
取扱説明書を見る
FR
DE
ES
IT
PT
NL
PO
RU
ZH
TW
KO
JP
AR
GO TO THE
USER MANUAL
www.focal.com/
quickstart/bathys
TÉLÉCHARGER L’APPLICATION
DOWNLOAD THE APP
x 1
C
Bathys
Bathys
Démarrage rapide / Quick Start
Accédez à la notice d’utilisation
Bedienungsanleitung lesen
Acceda a las instrucciones de uso
Accedi alle istruzioni per l’uso
Ir para o manual do utilizador
Ga naar de gebruiksaanwijzing
Przejdź do instrukcji obsługi
Перейти к инструкции по эксплуатации
访问使用说明
訪問用戶指南
사용설명서 보러가기
取扱説明書を見る
FR
DE
ES
IT
PT
NL
PO
RU
ZH
TW
KO
JP
AR
GO TO THE
USER MANUAL
www.focal.com/
quickstart/bathys
x 1
A
x 1
B
D
E
1
2
4s
R
3
R
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
in altre lingue
- English: Focal 091BATHYS User manual
- français: Focal 091BATHYS Manuel utilisateur