Schneider Electric Enerlin’X IFE Ethernet Interface Guida utente

www.se.com

Enerlin’X IFE

Ethernet Interface for One UL Circuit Breaker

User Guide

0602IB1801EN-08

06/2023

Legal Information

The Schneider Electric brand and any trademarks of Schneider Electric SE and its

subsidiaries referred to in this guide are the property of Schneider Electric SE or its

subsidiaries. All other brands may be trademarks of their respective owners.

This guide and its content are protected under applicable copyright laws and furnished

for informational use only. No part of this guide may be reproduced or transmitted in

any form or by any means (electronic, mechanical, photocopying, recording, or

otherwise), for any purpose, without the prior written permission of Schneider Electric.

Schneider Electric does not grant any right or license for commercial use of the guide

or its content, except for a non-exclusive and personal license to consult it on an "as is"

basis. Schneider Electric products and equipment should be installed, operated,

serviced, and maintained only by qualified personnel.

As standards, specifications, and designs change from time to time, information

contained in this guide may be subject to change without notice.

To the extent permitted by applicable law, no responsibility or liability is assumed by

Schneider Electric and its subsidiaries for any errors or omissions in the informational

content of this material or consequences arising out of or resulting from the use of the

information contained herein.

As part of a group of responsible, inclusive companies, we are updating our

communications that contain non-inclusive terminology. Until we complete this

process, however, our content may still contain standardized industry terms that may

be deemed inappropriate by our customers.

Ethernet Interface for One UL Circuit Breaker

Table of Contents

Safety Information............................................................................................7

About the Book ................................................................................................9

IFE Interface Presentation ............................................................................ 11

Introduction ...................................................................................................12

Intelligent Modular Unit...................................................................................14

Hardware Description.....................................................................................18

EcoStruxure Power Commission Software .......................................................24

Schematics with MasterPact MTZ Circuit Breakers ...........................................26

Schematics with MasterPact NT/NW and PowerPacT P- and R-Frame Circuit

Breakers........................................................................................................28

Technical Characteristics ................................................................................32

Firmware Update ...........................................................................................34

Schneider Electric Green Premium™Ecolabel..................................................36

Security Features ...........................................................................................38

Machine to Machine Communication ...............................................................39

Role Based Access Control ............................................................................40

Security Logs.................................................................................................43

IFE Interface Webpages from Firmware Version 004 ...............................44

Webpage Access and User Interface ...............................................................45

Access to IFE Webpages ..........................................................................46

User Interface Layout................................................................................50

Webpage Description ...............................................................................53

Settings Pages ..............................................................................................55

Date and Time..........................................................................................56

Time Zone ...............................................................................................57

Preferences .............................................................................................58

Ethernet...................................................................................................59

IP Configuration .......................................................................................61

Email Service...........................................................................................63

Data Publishing ........................................................................................65

Redundancy-RSTP ..................................................................................67

SNMP......................................................................................................69

Devices ...................................................................................................71

Emails .....................................................................................................73

Security Pages...............................................................................................74

IP Network Services .................................................................................75

Modbus TCP/IP Filtering ...........................................................................76

Certificates...............................................................................................78

User Management....................................................................................80

Syslog Service .........................................................................................83

Monitoring and Control Pages .........................................................................84

Circuit Breakers........................................................................................85

Diagnostics Pages .........................................................................................90

Status......................................................................................................91

0602IB1801EN-08 3

Ethernet Interface for One UL Circuit Breaker

Ethernet...................................................................................................92

Modbus ...................................................................................................93

ULP.........................................................................................................94

Redundancy-RSTP Bridge ........................................................................95

Redundancy-RSTP Ports..........................................................................96

SNMP......................................................................................................97

IFE .........................................................................................................98

Devices .................................................................................................100

IFE Interface Webpages up to Firmware Version 003 ............................102

Webpage Access and User Interface ............................................................. 103

Access to IFE Webpages ........................................................................104

User Interface Layout.............................................................................. 107

Webpage Description .............................................................................109

Configuration & Settings Webpages .............................................................. 111

General ................................................................................................. 112

Date and Time........................................................................................ 113

Time Zone ............................................................................................. 115

Ethernet Configuration (Dual Port) ........................................................... 116

IP Configuration ..................................................................................... 117

Modbus TCP/IP Filtering ......................................................................... 119

Email Server Configuration...................................................................... 120

Email Events.......................................................................................... 122

Device List ............................................................................................. 131

Device Logging ......................................................................................132

Device Log Export ..................................................................................134

SNMP Parameters .................................................................................136

Preferences ........................................................................................... 137

Advanced Services Control .....................................................................138

User Accounts........................................................................................ 139

Webpage Access ...................................................................................141

Monitoring Webpages................................................................................... 142

Real Time Data ......................................................................................143

Device Logging ......................................................................................145

Control Webpages .......................................................................................149

Device Control ....................................................................................... 150

Set Device Time ..................................................................................... 153

Diagnostics Webpages.................................................................................154

Statistics................................................................................................155

Device Identification ............................................................................... 158

IMU Information...................................................................................... 159

Read Device Registers ...........................................................................160

Communication Check............................................................................161

IO Readings........................................................................................... 162

Maintenance Webpages ...............................................................................163

Indicators...............................................................................................163

Appendices....................................................................................................164

Appendix A - List of IFE Supported Devices ................................................... 165

4 0602IB1801EN-08

Ethernet Interface for One UL Circuit Breaker

List of IFE Supported Device Types ......................................................... 165

0602IB1801EN-08 5

Safety Information Ethernet Interface for One UL Circuit Breaker

Safety Information

Important Information

Read these instructions carefully, and look at the equipment to become familiar with

the device before trying to install, operate, service, or maintain it. The following special

messages may appear throughout this documentation or on the equipment to warn of

potential hazards or to call attention to information that clarifies or simplifies a

procedure.

Please Note

Electrical equipment should be installed, operated, serviced, and maintained only by

qualified personnel. No responsibility is assumed by Schneider Electric for any

consequences arising out of the use of this material.

A qualified person is one who has skills and knowledge related to the construction and

operation of electrical equipment and its installation, and has received safety training

to recognize and avoid the hazards involved.

The addition of this symbol to a “Danger” or “Warning” safety label indicates that an

electrical hazard exists which will result in personal injury if the instructions are not

followed.

This is the safety alert symbol. It is used to alert you to potential personal injury

hazards. Obey all safety messages that follow this symbol to avoid possible injury or

death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

!

DANGER

WARNING indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

WARNING

!

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

CAUTION

!

NOTICE is used to address practices not related to physical injury.

NOTICE

0602IB1801EN-08 7

Ethernet Interface for One UL Circuit Breaker Safety Information

Cybersecurity Safety Notice

WARNING

POTENTIAL COMPROMISE OF SYSTEM AVAILABILITY, INTEGRITY, AND

CONFIDENTIALITY

• Change default passwords at first use to help prevent unauthorized access to

device settings, controls, and information.

• Disable unused ports/services and default accounts to help minimize pathways

for malicious attackers.

• Place networked devices behind multiple layers of cyber defenses (such as

firewalls, network segmentation, and network intrusion detection and protection).

• Use cybersecurity best practices (for example, least privilege, separation of

duties) to help prevent unauthorized exposure, loss, modification of data and

logs, or interruption of services.

Failure to follow these instructions can result in death, serious injury, or

equipment damage.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designated to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at this own expense.

8 0602IB1801EN-08

About the Book Ethernet Interface for One UL Circuit Breaker

About the Book

Document Scope

The aim of this document is to provide the users, installers, and the maintenance

personnel with the technical information and procedure needed to access and

maintain the IFE Ethernet interface for one circuit breaker webpages.

Validity Note

This guide is valid for the IFE interface for use with:

• MasterPact™MTZ circuit breakers

• MasterPact™NT/NW circuit breakers

• PowerPacT™P- and R-frame NS630b - NS1600 circuit breakers

• PowerPacT™H-, J-, and L-frame circuit breakers

NOTE:

The information related to the new generation of ComPacT NSX circuit breakers

in this guide applies to the existing range of ComPact NSX circuit breakers also.

The information related to the new generation of ComPacT NS circuit breakers in

this guide applies to the existing range of ComPact NS circuit breakers also.

The exceptions are mentioned wherever applicable. The new ranges are based

on the same technical and dimensional architecture as that of the exiting range of

circuit breakers.

Online Information

The technical characteristics of the devices described in this guide also appear online.

To access the information online, go to the Schneider Electric home page at www.se.

com.

The information contained in this guide is likely to be updated at any time. Schneider

Electric strongly recommends that you have the most recent and up-to-date version

available on www.se.com/ww/en/download.

Related Documents

Title of Documentation Reference Number

Enerlin’X IFE - Ethernet Interface for One Circuit Breaker - Instruction Sheet QGH13473

Enerlin'X IFE Interface Firmware Release Note DOCA0147EN

ULP System (UL Standard) - User Guide 0602IB1503 (EN)

MasterPact MTZ Modbus Communication Guide DOCA0105EN

MasterPact NT/NW, PowerPacT P- and R-frame Modbus Communication Guide 0613IB1313 (EN)

Enerlin'X IO Input/Output Application Module (UL Standard) - User Guide 0613IB1317 (EN)

PowerPact H-, J-, and L-Frame Modbus Communication Guide 0611IB1302 (EN)

MasterPact MTZ - Cybersecurity Guide DOCA0122EN

EcoStruxure Cybersecurity Admin Expert Guide CAE_UM_EN

0602IB1801EN-08 9

Ethernet Interface for One UL Circuit Breaker About the Book

You can download these technical publications and other technical information from

our website at www.se.com/ww/en/download/.

10 0602IB1801EN-08

Ethernet Interface for One UL Circuit Breaker

IFE Interface Presentation

What’s in This Part

Introduction .........................................................................................................12

Intelligent Modular Unit.........................................................................................14

Hardware Description...........................................................................................18

EcoStruxure Power Commission Software.............................................................24

Schematics with MasterPact MTZ Circuit Breakers.................................................26

Schematics with MasterPact NT/NW and PowerPacT P- and R-Frame Circuit

Breakers .............................................................................................................28

Technical Characteristics......................................................................................32

Firmware Update .................................................................................................34

Schneider Electric Green Premium™Ecolabel........................................................36

0602IB1801EN-08 11

Ethernet Interface for One UL Circuit Breaker Introduction

Introduction

Overview

The IFE Ethernet interface for one circuit breaker (or IFE interface) enables an

intelligent modular unit (IMU), with a ComPacT™, PowerPacT™, or MasterPact™

circuit breaker to be connected to an Ethernet network. Each circuit breaker has its

own IFE interface and a corresponding IP address.

The IFE interface with part number LV434001 is an Ethernet interface for ComPact,

PowerPact, and MasterPact circuit breakers.

NOTE: The IFE interface with part number LV434001 completely replaces the

IFE interface with part number LV434010. The LV434001 comes with the real time

clock (RTC) feature and allows ULP connections up to 20 m (65.6 ft) with the

MasterPact MTZ circuit breakers (LV434010 had a theoretical limitation of 5 m

(16.4 ft) over the life of the IFE interface).

IFE Interface Features

The main features of IFE interface are:

• Dual 10/100 Mbps Ethernet port for simple daisy chain connection

• Device profile web service for discovery of the IFE interface on the local area

network (LAN)

• ULP compliant for location of the IFE interface in the switchboard

• Ethernet interface for ComPacT, PowerPacT, and MasterPact circuit breakers

• Embedded settings webpages

• Embedded monitoring and control webpages

• Embedded diagnostics webpages

• Embedded security webpages

• Built-in email alarm notification for circuit breaker connected to IFE interface.

• IEC 61850 interface for MasterPact MTZ drawout circuit breakers

• Machine-to-Machine compliance

• Role-based access control (RBAC) for users accessing the webpages

IFE Firmware Versions

This guide describes the webpages for two different firmware versions of

IFE interface:

•Chapter 2, page 44 describes the IFE interface webpages for the firmware

version 004 and later.

•Chapter 3, page 102 describes the IFE interface webpages for the firmware

versions up to 003.

12 0602IB1801EN-08

Introduction Ethernet Interface for One UL Circuit Breaker

IFE Interface Supported Protocols

The IFE interface supports the following Ethernet protocols:

•Modbus TCP/IP: is a protocol, which provides master/slave communication

between devices and TCP/IP that provides communications over an Ethernet

connection. Modbus TCP/IP is used to exchange data between IFE interface and

other compatible Modbus TCP/IP devices through TCP port 502.

•Hypertext Transfer Protocol (HTTP): HTTP is a network protocol that handles

delivery of files and data on the World Wide Web. It provides web server

functionality through TCP port 80. Remote configuration of IFE interface and

viewing of diagnostic data is possible using a web browser.

•Hypertext Transfer Protocol Secure (HTTPS): HTTPS is a variant of the

standard web transfer protocol (HTTP) that adds a layer of security on the data in

transit through a Transport Layer Security (TLS) protocol connection. HTTPS

enables encrypted communication and secure connection between a remote user

and the IFE interface.

•File Transfer Protocol Secure (FTPS): FTPS is a variant of the standard File

Transfer Protocol (FTP) that adds a layer of security on the data in transit through

a Transport Layer Security (TLS) protocol connection. FTPS enables encrypted

communication and secure connection between a remote user and the IFE

interface.

NOTE: For IFE interface with firmware version 004.006.000 and later, use a

FTPS client, such as FileZilla or WinSCP to transfer the IEC 61850

configuration files.

•Simple Network Management Protocol (SNMP): Based on MIB2 format, SNMP

provides the ability to store and send identifying and diagnostic information used

for network management purposes through UDP port 161.

•Rapid Spanning Tree Protocol (RSTP EcoStruxure Power Commission

Software): RSTP is a network protocol that ensures a loop-free topology for

Ethernet networks.It is the advanced version of Spanning Tree Protocol, is a link

layer protocol executed within bridges or switches.

•Devices Profile for Web Services (DPWS): DPWS defines a minimal set of

implementation constraints to enable secure web service messaging, discovery,

description, and eventing on resource-constrained devices.

•Network Time Protocol (NTP): NTP is a networking protocol for clock

synchronization between computer systems over packet-switched, variable-

latency data networks.

•IEC 61850 Protocol: IEC 61850 is a standard for communication networks and

systems in substations. Based on Ethernet protocol, it is a standardized method

of communication developed to support integrated systems, composed of multi-

vendor, self-describing IEDs (Intelligent Electronic Devices) that are networked

together to perform real-time protection, control, measurement, and monitoring

functions.

NOTE: HTTPS, FTPS, RSTP, NTP, and IEC 61850 protocols are applicable only

from IFE interface firmware version 004.000.000.

0602IB1801EN-08 13

Ethernet Interface for One UL Circuit Breaker Intelligent Modular Unit

Intelligent Modular Unit

Definition

A modular unit is a mechanical and electrical assembly containing one or more

products to perform a function in a switchboard (incoming protection, motor

command, and control).

The circuit breaker with its internal communicating components (MicroLogic control

unit or MicroLogic trip unit) and external ULP modules (IO module) connected to one

communication interface is called an intelligent modular unit (IMU).

An IMU is composed around a circuit breaker from the following ranges:

• MasterPact MTZ circuit breakers

• MasterPact NT/NW circuit breakers

• ComPacT NS1600b-3200 circuit breakers

• ComPacT NS630b-1600 circuit breakers

• PowerPacT P- and R- frame circuit breakers

• ComPacT NSX circuit breakers

• PowerPacT H-, J-, and L-frame circuit breakers

NOTE:

• The information related to the new generation of ComPacT NSX and

PowerPacT H-, J-, and L- frame circuit breakers in this guide applies to the

existing range ComPact NSX and PowerPact H-, J-, and L- frame circuit

breakers also.

The information related to the new generation of ComPacT NS and

PowerPacT P-, and R-frame circuit breakers in this guide applies to the

existing range ComPact NS and PowerPact P-, and R-frame circuit breakers

also.

The exceptions are mentioned wherever applicable. The new ranges are

based on the same technical and dimensional architecture as that of the

exiting range of circuit breakers.

• ComPacT NS and PowerPacT P-, and R-frame circuit breakers is supported

for IFE interface with firmware version 004 only.

14 0602IB1801EN-08

Intelligent Modular Unit Ethernet Interface for One UL Circuit Breaker

ULP Modules Per Circuit Breaker Range

The following table lists the compatible ULP modules for each range of circuit

breakers.

ULP Module Part Number MasterPact MTZ with

ULP Port Module and

MicroLogic Control

Unit

MasterPact NT/NW or

ComPacT or PowePacT

P- and R-Frame with BCM

ULP Module and

MicroLogic Trip Unit

ComPacT NSX or

PowerPacT H-, J-, and L-

frame with BSCM Module

and/or MicroLogic Trip

Unit

IFE Ethernet interface for one

circuit breaker

LV434001

LV434010

✓ ✓ ✓

IFE Ethernet switchboard server LV434002

LV434011

✓ ✓ ✓

IFE Embedded Ethernet interface

for one MasterPact MTZ drawout

circuit breaker

LV851001 ✓– –

Spare part kitIFE for one

MasterPact MTZ1 drawout circuit

breaker

LV851100SP ✓– –

Spare part kitIFE for one

MasterPact MTZ2/MTZ3 drawout

circuit breaker

LV851200SP ✓– –

IFM Modbus-SL interface for one

circuit breaker

TRV00210

STRV00210

–✓ ✓

IFM Modbus-SL interface for one

circuit breaker

LV434000 ✓ ✓ ✓

FDM121 front display module for

one circuit breaker

TRV00121

STRV00121

–✓ ✓

IO input/output application module

for one circuit breaker

LV434063 ✓ ✓ ✓

USB maintenance interface TRV00911

STRV00911

–✓ ✓

For more information on the ULP System and its components, refer to the ULP

System User Guides.

0602IB1801EN-08 15

Ethernet Interface for One UL Circuit Breaker Intelligent Modular Unit

Communication Architecture

Trip

AFDM128 Ethernet display for eight devices

BFDM121 front display module for one circuit breaker

CIFE Ethernet interface for one circuit breaker

DIFE Ethernet switchboard server

EIFM Modbus-SL interface for one circuit breaker

FIO input/output application module for one circuit breaker

GMasterPact MTZ1 or MTZ2/MTZ3 drawout circuit breaker

HMasterPact MTZ1 or MTZ2/MTZ3 fixed circuit breaker

IMasterPact NT/NW circuit breaker

JComPacT NS/PowerPacT P-, and R-frame circuit breaker

KComPacT NSX/PowerPacT H-, J-, and L-frame circuit breaker

LULP port module

MIFE Embedded Ethernet Interface for one MasterPact MTZ drawout circuit breaker

NULP line termination

ORJ45 male/male ULP cord

PCircuit breaker BCM ULP cord

QNSX cord

16 0602IB1801EN-08

Intelligent Modular Unit Ethernet Interface for One UL Circuit Breaker

Remote Controller

A remote controller is a device that is able to communicate with an IMU using a

communication interface, such as the IFE Embedded Ethernet interface. For example,

FDM128 Ethernet display for eight devices, supervisor, PLC, BMS, SCADA system,

and so on, are remote controllers.

For the description of Modbus registers and commands, refer to the Modbus

Communication Guides.

0602IB1801EN-08 17

Ethernet Interface for One UL Circuit Breaker Hardware Description

Hardware Description

Description

AEthernet 1 and Ethernet 2 RJ45 communication ports

B24 Vdc power supply terminal block

CQR code to product information

DEthernet communication LEDs

EModule status LED

FNetwork status LED

GSealable transparent cover

HReset button

IULP status LED

JTest button (accessible even with closed cover)

KLocking pad

LDevice name label

MTwo RJ45 ULP ports

NGrounding connection

18 0602IB1801EN-08

Hardware Description Ethernet Interface for One UL Circuit Breaker

For information on installation, consult the instruction sheet available on the

Schneider Electric website: QGH13473.

Mounting

The IFE interface mounts on a DIN rail.

24 Vdc Power Supply

The IFE interface must always be supplied with 24 Vdc.

It is recommended to use an UL listed and recognized limited voltage/limited current

or a class 2 power supply with a 24 Vdc, 3 A maximum.

NOTE: For 24 Vdc power supply connection, use copper conductors only.

Ethernet Communication LEDs

The Ethernet communication dual color LEDs, indicate the status of the Ethernet ports

ETH1 and ETH2.

LED Indication Status Description

OFF No power or no link

Steady yellow 10 Mbps, link established, and no activity

Blinking yellow 10 Mbps, ongoing activity

Steady green 100 Mbps, link established, and no activity

Blinking green 100 Mbps, ongoing activity

0602IB1801EN-08 19

Ethernet Interface for One UL Circuit Breaker Hardware Description

Module Status LED

The module status dual color LED, indicates the IFE interface status.

LED Indication Status Description Action

OFF No power None

Steady green IFE interface operational None

Blinking green (250 ms ON, 250 ms OFF) Hidden control webpage available None

Blinking green (500 ms ON, 500 ms OFF) IFE interface firmware corrupted Contact your local Schneider Electric service

team for support.

Blinking red (500 ms ON, 500 ms OFF) IFE interface in degraded mode Replace ULP module at the next maintenance

operation.

Steady red IFE interface out of service None

Blinking green/red (1 s green, 1 s red) Firmware update in progress None

Blinking green/red (250 ms green, 250 ms red) Self-test in progress None

Network Status LED

The network status dual color LED, indicates the Ethernet network status.

LED Indication Status Description

OFF No power or no IP address

Steady green Valid IP address

Steady red Duplicated IP address

Blinking green/red (250 ms green, 250 ms red) Self-test in progress

Steady amber Error in IP configuration

Modbus Address

The IFE interface accepts the Modbus address of the IMU to which it is connected.

The Modbus address is 255 and cannot be changed.

Locking Pad

The locking pad on the front panel of the IFE interface enables or disables the ability

to send the remote control commands over the Ethernet network to the IFE interface,

and to the other modules of the IMU

• If the arrow points to the open padlock (default settings), remote control

commands are enabled.

• If the arrow points to the closed padlock, remote control commands are disabled.

The only remote control command that is enabled even if the arrow points to the

closed padlock, is the set absolute time command.

20 0602IB1801EN-08

La pagina sta caricando ...

Schneider Electric Enerlin’X IFE Ethernet Interface Guida utente

Schneider Electric Enerlin’X IFE Ethernet Interface Guida utente

Documenti correlati

Altri documenti