Sirio Antenne Gain Master HW Manuale utente

Marca: Sirio Antenne

Modello: Gain Master HW

Tipo: Manuale utente

WARNING

INSTALLATION OF THIS PRODUCT NEAR POWER

LINES IS DANGEROUS. FOR YOUR SAFETY, FOLLOW

THE ENCLOSED INSTALLATION DIRECTIONS.

YOU, YOUR ANTENNA, AND SAFETY

For your safety, and to help you achieve a good installation, please

2. Select your Installation site with safety, as well as performance, in

mind. (Detailed information on Site Selection appears in a separate

section of this booklet.) REMEMBER: ELECTRIC POWER LINES

AND PHONE LINES LOOK ALIKE. FOR YOUR SAFETY, ASSUME

THAT ANY OVERHEAD LINES CAN KILL YOU.

3. Call your electric power company. Tell them your plans and ask them

to come look at your proposed installation. This is a small

inconvenience considering YOUR LIFE IS AT STAKE.

DO NOT use a metal ladder. DO NOT work on a wet or windy day.

HOW TO INSTALL YOUR OUTDOOR ANTENNA

S A F E L Y I N A C C O R D A N C E W I T H T H E

RECOMMENDATIONS OF THE U.S. CONSUMER

PRODUCT SAFETY COMMISSION

READ and FOLLOW the safety precautions below. THEY MAY SAVE

YOUR LIFE!

7. If any part of the antenna system should come in contact with a power

line-DON'T TOUCH IT OR TRY TO REMOVE IT YOUR SELF. CALL

YOUR LOCAL POWER COMPANY. They will remove it safely.

These safety recommendations apply to all SIRIO

commercial, amateur and general purpose communication

antennas. SIRIO antenne assumes no liability if faulty or

dangerous installation practices are used. There are

available, trained and experienced personnel to assist in

installation, maintenance, or disassembly. Contact your

local installer if consultation or assistance is required.

Each year hundreds of people are killed, mutilated or receive severe

permanent injuries when attempting to install an antenna. In many of

these cases, the victim was aware of the danger of electrocution, but did

not take adequate steps to avoid the hazard.

1. If you are installing an antenna for the first time, please, for your own

safety as well as others, seek PROFESSIONAL ASSISTANCE.

Consult your dealer. He can explain which mounting method to use for

the size and type antenna you are about to install.

4. Plan your installation procedure carefully and completely before you

begin. Successful raising of a mast or tower is largely a matter of

coordination. Each person should be assigned to a specific task, and

should know what to do and when to do it. One person should be

designated as the "boss" of the operation to call out instructions and

watch for signs of trouble.

5. When installing your antenna, REMEMBER:

6. lf the assembly starts to drop, get away from it and let it fall.

Remember, the antenna, mast, cable and metal guy wires are all

excellent conductors of electrical current. Even the slightest touch of

any of these parts to a power line complete an electrical path through

the antenna and the installer-THAT'S YOU!

DO dress properly -shoes with rubber soles and heels, rubber gloves,

long sleeve shirt or jacket.

If an accident should occur with the power lines call for qualified

emergency help immediately.

If you are unable to maintain this safe distance, STOP! GET

PROFESSIONAL HELP. Many antennas are supported by pipe masts

attached to the chimney, roof or side of the house. Generally, the higher

the antenna is above the ground, the better it performs. Good practice is

to install your antenna about 5 to 10 feet above the roof line and away

from power lines and obstructions. Remember that FCC limits your

antenna height to 60 feet. If possible, find a mounting place directly

above your set, where the antenna wire can take a short, vertical drop on

the outside of the house for entry through a wall or window near the set.

Your dealer carries a complete line of installation hardware.

3. Double this total for the minimum recommended safe distance.

Before attempting to install your antenna, think where you can best place

your antenna for safety and performance.

SITE SELECTION

To determine a safe distance from wires, power lines and trees:

1. Measure the height of your antenna.

2. Add this length to the length of your tower or mast, and then

power lines should be

The safe distance from

mast combined.

at least twice the height

of the antenna and

CHOOSE A PROPER SUPPORT AND MOUNTING

METHOD

However you decide to mount and support your antenna always make

sure that safety is your first concern. Some of the more common

installation methods are illustrated below.

The swivel feature of "universal" type mounting brackets makes a

convenient antenna mount for flat or peaked roofs. One clamp type bracket

is used with 3 or 4 guy wires equally spaced around the mast and anchored

to the roof or eaves by eyebolts. Apply roofing compound around the base of

the bracket, screws and eyebolts for moisture sealing.

ROOF MOUNTING

AVOID THIS LOCATION

SAFETY INFORMATION SHEET

ROOF MOUNTED

COAXIAL CABLE

GROUND WIRE

TRIPOD MOUNT

2. On the ground, clamp the antenna to mast and connect the coaxial cable to the antenna.

5. If you are going to use guy wire installation instead of a mounting bracket:

- install guy anchor bolts

GENERAL INSTALLATION INSTRUCTIONS FOR

MAST MOUNTED ANTENNAS

1. Assemble your new antenna on the ground at the installation site. Keep separate

assembly instructions that come with it. Large CB and Amateur beams may have to be

finally assembled on the tower or mast.

3. To insure that the mast does not fall the "wrong way" if it should get away during the

installation or takedown, durable non-conductive rope should be secured at each two

foot level as the mast is raised. The boss stands in a position where he can yank or pull

the ropes if the need arise to deflect the falling mast away from hazards (such as power

lines) into a "safe fall" (such as a yard or driveway). The ropes are tied taut at the base of

the mast after installation and in place at the various levels.

- estimate length of guy wire and cut

4. Install selected mounting bracket.

- attach a mast using guy ring

8. Install ground rod to drain off static electricity build-up and connect ground wire to mast

and ground rod. Use special ground rods, not a spare piece of pipe.

AS PER NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING

INSTRUCTIONS

1. Use No. 10 AWG copper or No. 8 AWG or larger copper-clad steel or bronze wire, as

ground wires for both mast and lead-in. Securely clamp the wire to the bottom of the

mast.

7. Install self-adhering "DANGER" label packaged in antenna hardware kit at eye level on

your mast.

3. Mount antenna discharge unit as close as possible to where the lead-in wire enters the

house.

6. Put small amount of caulking around cable where it enters house to keep out drafts.

7. Install static electricity discharge unit.

8. Connect antenna cable to the set.

2. Secure lead-in wire from antenna to antenna discharge unit and mast ground wire to

house with stand-off insulators spaced from 4 feet (1.2 meters) to 6 feet (1.8 meters)

apart.

6. Carefully take antenna and mast assembly to mounting bracket and insert. Tighten

camp bolts. In case of guyed installation, it will be necessary to have at least a second

person hold the mast upright while the guy wires are attached and tightened to the

anchor bolts.

4. Drill a hole in wall (CAREFUL! There are wires in thatwall.) near your set just large

enough to permit entry of cable.

5. Push cable through hole and form a rain drip loop close to where it enters the house.

You should not attempt to raise a

mast in excess of 30 feet in

height/length (not including the

antenna proper) in a fully-

extended condition. Thirty to fifty

foot tubular masts must be

elevated , a section at a time,

with the base or outer section

secured in place with guy wires.

GET PROFESSIONAL HELP.

TOWER

TELESCOPING MAST

Guy wires should be equally spaced in at least three directions. Use at least three

guy wires for each 10 foot section of mast.

SIDE OF HOUSE MOUNTING

The safe distance from power lines is at least twice the height of antenna and

mastcombined. Where roofoverhang is not excessive, the side ofthe house

provides a convenient mounting. Position the brackets over a stud if possible,

one above the other, and space two or three feet apart. For metal siding, first

mark mounting holes, then drill pilot holes through the siding to accept mounting

screws.

Tower safety is paramount to a good installation and requires that you take

location, tree growth, soil depth and proximity to buildings into consideration.

Tower foundations must be securely based on a solid concrete/ tower mounting

plate. An alternative is to sink a 4-6 foot section of tower into a concrete base for

an extremely rugged mount. Proper guying is essential to a safe weather-

resistant installation that must handle severe wind loading and is best

accomplished with preformed guy grips, torque brackets and turnbuckles. When

working on towers always use a safety belt made of high quality web-type

material

CHIMNEY MOUNTING

The chimney is often an easy and convenient

mounting place. But the chimney must be

strong enough to support the antenna in high

winds. Do not use a chimney that has loose

bricks or mortar. A good chimney mount

makes use of a 5 or 10 foot, 1-1/4" diameter

steel mast, and a heavy duty two strap

clamp-type bracket. Install the upper

bracketjust below the top course of bricks,

and the lower bracket two or three feet below

the upper bracket. For maximum strength,

space the brackets as lar apart as possible. SAFETY INFORMATION SHEET ID416 Rev.C

TOWER

HOUSE

SIDE

MOUNT

COAX CABLE

MAST GROUNDED GROUND

WIRE STATIC

DISCHARGE

UNIT TO

GROUND ROD

TELESCOPING

MAST

GROUND

WIRE

GROUND

CLAMP

MAST

ANTENNA

GROUND

ROD

GROUND

CLAMPS

ANTENNA

GROUND

WIRE

STATIC

DISCHARGE

UNIT

DOWNLEAD

TO SET

ANTENNA GROUNDING

PER NATIONAL

ELECTRICAL CODE

All articles displaying this symbol on the body,

packaging or instruction manual of same, must not be

thrown away into normal disposal bins but brought to

specialised waste disposal centres. Here, the various

materials will be divided by characteristics and

recycles, thus making an important contribution to

environmental protection.

I N F O R M AT I O N S D E S É C U R I T É

Sirio Antenne n'assure aucune responsabilité en cas d'installation défectueuse

ou dangereuse. Il est indispensable de disposer de personnel compétent et

expérimenté pour aider à l'installation, l'entretien ou le démontage du produit.

Contactez votre installateur pour demander une assistance.

1. Si vous installez une antenne pour la première fois, pour votre sécurité, faites-

vous assister et conseiller par un PROFESSIONNEL. Consultez votre

revendeur qui pourra vous expliquer la méthode de montage à utiliser en

fonction de de la taille et du type d'antenne que vous souhaitez monter.

2. Choisissez un endroit d'installation sûr. La distance de sécurité par rapport à

des lignes à haute tension, doit être d'au moins deux fois la hauteur de

l'antenne et du mât. RAPPEL: LES LIGNES A HAUTE TENSION ET LES

LIGNES TELEPHONIQUES PEUVENT SE CONFONDRE. UNE LIGNE A

HAUTE TENSION PEUT VOUS TUER ! Quand vous installez une antenne,

ISTRUZIONI GENERALI

4. Se una qualsiasi parte dell’antenna dovesse entrare in contatto con una linea di

elettricità, NON TOCCATELA. Chiamate gli operatori della società elettrica, sapranno

rimuoverla in modo sicuro e corretto.

c) UTILIZZATE un abbigliamento appropriato (scarpe con suola in gomma,

guanti in gomma, maglia con manica lunga)

FOGLIO INFORMATIVO DI SICUREZZA

b) NON LAVORATE in un giorno di vento o di pioggia;

3. Se il vostro impianto inizia a cedere, allontanatevi e lasciatelo cadere. Ricordate che

l’antenna, il palo, il cavo e i fili di metallo sono ottimi conduttori di elettricità. Anche il

contatto più lieve di una di queste parti alle linee dell’alta tensione provoca un

collegamento elettrico dalla linea all’installatore attraverso l’antenna.

5. NON SOSTARE vicino all’antenna mentre sta trasmettendo.

7. Attaccare sul palo di sostegno l’etichetta autoadesiva “DANGER” contenuta nella

confezione in posizione visibile (altezza occhi).

3. Assicurarsi del corretto serraggio di dadi e viti.

4. Se necessario (zone molto ventose o palo di sostegno molto lungo) si consiglia l’utilizzo

di tiranti di controventatura.

6. Si consiglia di rispettare sempre la potenza massima stabilita dalle norme vigenti

SIRIO antenne non si assume alcuna responsabilità se si utilizzano pratiche di installazione

pericolose. E' disponibile personale qualificato e con esperienza per assistervi nell

installazione, manutenzione, o lo smontaggio. Contattate il vostro installatore locale per

richiedere una consulenza o assistenza.

1. Se state installando un’antenna per la prima volta, richiedete un’ASSISTENZA

PROFESSIONALE. Consultate il vostro rivenditore che saprà spiegarvi il metodo più

idoneo e sicuro per montare il tipo di antenna che volete utilizzare.

2. Scegliete il luogo più sicuro per l’installazione. La distanza di sicurezza dalle linee

dell’alta tensione deve essere almeno due volte l’altezza dell’antenna con il palo.

RICORDATE: LE LINEE DELL’ALTA TENSIONE E LE LINEE TELEFONICHE SONO

SIMILI PERTANTO STATE LONTANO DA QUALSIASI LINEA DI TENSIONE.

POTREBBE UCCIDERVI !! Quando installate la vostra antenna, RICORDATE:

a) NON USATE scale di metallo;

1. Seguire attentamente le istruzioni di montaggio sul foglio illustrativo allegato al prodotto.

2. Collegare il palo di sostegno a terra utilizzando una trecciola in rame con una sezione di

almeno 6 mm .

b) NE TRAVAILLEZ PAS un jour humide ou venteux,

RAPPELEZ-VOUS :

a) N'UTILISEZ PAS d'échelle métallique,

4. Si l'une des parties de l'antenne et des accessoires, venaient à être en contact

avec une à ligne haute tension, NE TOUCHEZ A RIEN, N'ESSAYEZ PAS DE

DEMONTER VOUS- M Ê M E. APPELEZ L E FOUR N I S SEUR

D'ELECTRICITE qui démontera l'antenne avec les précautions requises.

3. Si l'assemblage commence à tomber, s'en éloigner et le laisser tomber.

Rappelez-vous que l'antenne, le mât, les câbles et les fils de fer sont

d'excellents conducteurs de courant électrique. Même le plus léger contact

d'une de ces pièces avec une ligne haute tension peut créer un contact

électrique au travers de l'antenne et de l'installateur.

IINSTRUCTIONS GENERALES pour les antennes montées sur un mât:

c) UTILISEZ des vêtements appropriés (chaussure et talons en

caoutchouc, gants en caoutchouc, chemise ou veste à manches

longues).

1. Suivez avec attentions les instructions de montage du produit.

2. Branchez votre mât à la masse en utilisant un fil de cuivre d'une section

minimale de 6 mm .

3. Faîtes attention au bon serrage des écrous et des vis.

4. Si nécessaire (endroits venteux ou mâts très hauts) utilisez des haubans.

5. NE RESTEZ PAS à côté de votre antenne si celle-ci est en émission (TX).

6. Respectez strictement la puissance maximale exigée par la loi et la

règlementation.

7. Mettez un autocollant «DANGER» sur le mât, à hauteur des yeux.

b) Führen sie diese Arbeiten, wenn möglich, nicht an regnerischen oder

stürmischen Tagen aus.

ALLGEMEINE MONTAGEANWEISUNGEN FÜR ANTENNEN, DIE AUF EINEM MAST

MONTIERT SIND:

2. Verbinden Sie Ihren Mast mit einem guten Erdungspotential, indem Sie einen

Kupferdraht mit einem Querschnitt von mindestens 6 mm verwenden.

5. Halten Sie sich nicht in der Nähe Ihrer Antenne auf, während Ihr Funkgerät im

1. Befolgen Sie sorgfältig die Montageanweisungen des Produkts.

c) Achten sie auf richtige Kleidung: (Schuhe mit Gummisohlen und -absätzen,

Gummihandschuhe, Hemd bzw. Jacke mit langen Armen).

3. Achten Sie auf den korrekten Sitz von Muttern und Schrauben.

4. Wenn notwendig (Gegenden mit häufigen starken Winden bzw. Stürmen oder sehr hohe

Masten) wird die Verwendung von speziellen Abspannseilen (Erhältlich im guten

Fachhandek) empfohlen.

3. Sollte bei der Montage Antenne oder Mast aus irgendwelchen Gründen hinfallen, sollten

Sie diese in diesem Moment nicht mehr berühren. Denken Sie daran, daß Antenne,

Mast, Kabel und metallische Verankerungsdrähte ausgezeichnete Leiter von

elektrischen Strom sind. Selbst die leichteste Berührung dieser Teile mit einer

Stromleitung erzeugt einen elektrischen Stromkreis und kann Sie sofort töten.

4. Wenn irgendein Teil des Antennensystems mit einer Stromleitung in Kontakt kommen

sollte, BERÜHREN SIE ES NICHT UND VERSUCHEN SIE NICHT, ES SELBST ZU

ENTFERNEN. RUFEN SIE IHRE ÖRTILICHE ELEKTRIZITÄTSGESELLSCHATF AN.

Die Fachleute dieser Gesellschaften werden das Problem sicher und gefahrlos lösen.

SICHERHEITS-INFORMATIONSBLATT

1. Wenn Sie zum ersten Mal eine Antenne installieren, sollten Sie sich von Ihrem

Fachhändler beraten lassen. Er kann Ihnen erklären, welche Montagemethode für die

Größe und den Typ der Antenne, die Sie montieren wollen, zu verwenden ist.

a) Verwenden sie keine Metall-Leiter.

SIRIO Antenne übernimmt keine Haftung, wenn fehlerhafte oder gefährliche

Installationspraktiken angewandt werden. Es steht geschultes und erfahrenes Personal zur

Verfügung, um Sie bei der Installation, Wartung oder Demontage zu unterstützen.

Kontaktieren Sie Ihren Fachhändler, wenn Beratung oder Unterstützung erforderlich ist

2. Wählen Sie Ihren Installatiosort unter dem Gesichtspunkt der Sicherheit aus. Der

Sicherheitsabstand von Stromleitungen sollte mindestens das Doppelte der

gemeinsamen Länge von Antenne und Mast betragen. OFT KÖNNEN SIE ALS LAIE

ELEKTRISCHE STROMLEITUNGEN UND TELEFONLEITUNGEN NICHT

UNTERSCHEIDEN. - GEHEN SIE ZU IHRER EIGENEN SICHERHEIT ZUNÄCHST

EINMAL DAVON AUS, DASS JEGLICHE LUFTLEITUNGEN SIE TÖTEN KÖNNTE !!

Wenn Sie Ihre Antenne installieren, DENKEN SIE DARAN:

L’INSTALLAZIONE DI QUESTO PRODOTTO VICINO

ALLE LINEE DELL’ALTA TENSIONE E’ PERICOLOSA.

SEGUIRE LE ISTRUZIONI PER LA VOSTRA SICUREZZA

ATTENZIONE

Il simbolo del cassonetto barrato indica che il prodotto alla fine della propria

vita utile deve essere raccolto separatamente dagli altri rifiuti.

L’utente dovrà, pertanto, conferire l’apparecchiatura giunta a fine vita agli

idonei centri di raccolta differenziata dei rifiuti elettrici ed elettrotecnici, oppure

riconsegnare al rivenditore al momento dell’acquisto di una nuova

apparecchiatura di tipo equivalente, in ragione di uno a uno. L’adeguata

raccolta differenziata e l’avvio al riciclaggio, al trattamento e allo smaltimento

ambientale compatibile contribuisce ad evitare effetti negativi sull’ambiente e

sulla salute e favorisce il reimpiego e/o riciclo dei materiali. Lo smaltimento dei

rifiuti abusivo del prodotto da parte dell’utente comporta l’applicazione delle

sanzioni amministrative previste dalla normativa vigente.

Tous les articles présentant ce symbole sur le corps,

l'emballage ou le manuel d'utilisation de celui-ci ne doivent

pas être jetés dans des poubelles normales mais être

amenés dans des centres de traitement spécialisés. Là, les

différents matériaux seront séparés par caractéristiques et

recyclés, permettant ainsi de contribuer à la protection de

l'environnement.

ai sensi dell’art.13 del Decreto Legislativo 25 luglio 2005, n.

151 «Attuazione Direttive 2002/95/CE, 2002/96/CE e

2003/108/CE», relative alla riduzione dell’uso di sostanze

pericolose nelle apparecchiature elettriche ed elettroniche,

nonché allo smaltimento dei rifiuti».

INFORMAZIONE AGLI UTENTI ITALIANI

INFO FOR ITALIAN USERS ONLY

L'INSTALLATION DE CE PRODUIT PROCHE DE LIGNES

A HAUTE TENSION EST DANGEREUSE. POUR VOTRE

SECURITE, SUIVEZ LES INDICATIONS JOINTES.

ATTENTION

DIE INSTALLATION DIESES PRODUKTS IN DER NÄHE VON

STROMLEITUNGEN IST GEFÄHRLICH. BEFOLGEN SIE ZU

IHRER SICHERHEIT DIE FOLGENDEN ANWEISUNGEN.

WARNUNG

6. Nepouzivejte vysi vykon nez je vyrobcem urceno

BEZPECNOSTNÍ INFORMACNÍ LIST.

2. Pouzivejte ochranny oblek

1. Pozorne ctete montazni navod

2. Antenni stozar uzemnete vodicem 6mm2

3. Pri istalaci do anteny nevysilejte

3. Zvysenou pozornost venujte kontaktum a spojum

4. Nemontujte antenu v extremne nepriznivem pocasi

7. Antenu oznacte stitkem “ ” DANGER

SIRIO nepřebírá žádnou zodpovědnost v případě neodborné či nebezpečné

montáže. Montáž, údržbu nebo demontáž svěřte kvalifikovanémua

odbornému servisu.

5. Pri vysilani se nedotykejte zarice

Zakladni instrukce:

1. Pokud nemate s montazi zkusenosti, pouzijte odbornou firmu

4. Pri jakemkoli kontaktu s elektrickym vedenim informujte rozvodne zavody

SIRIO Antenne no asume ninguna responsabilidad si se efectúan acciones irresponsables

o peligrosas en el momento de la instalación. Hay personal disponible, capacitado y con la

experiencia necesaria para ayudar o realizar l mantenimiento, montaje y desmontaje. e

Póngase en contacto con su instalador local si precisa asesoramiento o asistencia.

HOJA DE INFORMACIÓN DE SEGURIDAD

1. Si usted pretende instalar una antena por primera vez, déjese aconsejar por un

profesional, consulte en su establecimiento habitual y siga todas sus recomendaciones.

2. Elija el lugar más seguro para la instalación. La distancia de seguridad con respecto a la

línea de alta tensión, deberá ser al menos dos veces la altura de la antena, una vez

instalada en el mástil. RECUERDE: LAS LÍNEAS DE ALTA TENSIÓN Y LAS LÍNEAS

TELEFÓNICAS SON PARECIDAS. PARA SU SEGURIDAD MANTENGASE

ALEJADO DE ELLAS. Cuando instale la antena, RECUERDE:

c) UTILICE ropa y material adecuado (zapatos aislantes con suela de goma,

guantes de goma, camisa de manga larga)

a) NUNCA utilice una escalera metálica

b) NO pretenda instalar la antena en un día con viento, lluvia o nieve.

4. Si una parte de la antena entrara en contacto con algún cable eléctrico ALEJESE

INMEDIATAMENTE. Llame urgentemente a la compañía eléctrica, NO intente

resolver por su cuenta el incidente. Ellos sabrán solucionar el problema de un modo

correcto y seguro.

INSTRUCCIONES GENERALES

1. Siga atentamente las instrucciones de la hoja ilustrativa que acompaña al producto.

2. Si tiene alguna duda NO prosiga con la instalación. Consulte personal cualificado

3. Derive a tierra el mástil de sujeción mediante un cable de 6mm . de sección mínimo.

3. Si la instalación no está bien efectuada, ésta podría caer, ocasionar grandes

desperfectos e incluso causando daños a terceros. Le recomendamos proceda con

extremada precaución.

4. Verifique que los tornillos y tuercas han sido debidamente fijados.

6. NO PERMANEZCA cerca de la antena mientras se está transmitiendo.

5. Si es necesario (zonas de mucho viento o mástiles muy largos) utilice tirantes de

vientos.

7. Se aconseja siempre respetar la potencia máxima establecida por las normas vigentes

8. Coloque en el mástil la etiqueta autoadhesiva “ ” suministrada con la antena, DANGER

situela en un lugar lo suficientemente visible. (Altura de la vista)

SIRIO Antenne nie ponosi żadnej odpowiedzialności w razie awarii instalacji w wyniku

błędnego zamontowania lub stosowanych niebezpiecznych praktyk. W przypadku

problemów podczas montażu należy skontaktować się z przeszkolonym i doświadczonym

personelem jak i w celu konserwacji czy demontażu.

7. Oznacz instalacje ostrzegawczą nalepką « ».DANGER

6. Nie przekraczaj limitów mocy.

3. Starannie skręcaj połączenia.

3. Jeżeli montowana konstrukcja zaczyna się przewracać nie podtrzymuj jej.

KARTA INFORMACJI BEZPIECZEŃSTWA

2. Wybierz starannie miejsce montażu w odległości minimum 2 długości anteny plus masztu

od linii energetycznej. Nie używaj metalowej drabiny, załóż buty z gumowa podeszwą,

rękawiczki, koszulę z długim rękawem i nie pracuj w złych warunkach pogodowych.

Podstawowe instrukcje:

1. Zapoznaj się z instrukcją produktu.

2. Uziemij maszt przewodem min. 6 mm ˛.

4. Używaj odpornych na wiatr elementów masztu.

1. Montując antenę po raz pierwszy, dla własnego bezpieczeństwa, poproś o pomoc

specjalistów.

4. Jeżeli część instalacji już dotknęła kabli z prądem nie usuwaj jej sam tylko zadzwoń od

zakładu energetycznego.

5. Nie przebywaj w pobliżu anteny podczas nadawania.

LA INSTALACIÓN DE ESTE PRODUCTO CERCANO A UNA

LÍNEA DE ALTA TENSIÓN PUEDE SER PELIGROSO. SIGA

ATENTAMENTE LAS INSTRUCCIONES PARA SU SEGURIDAD.

2.Тщательно выбирайте место установки. Расстояние до высоковольтной

ЛЭП должно, как минимум, дважды превышать высоту мачты и антенны.

информация о безопасности

SIRIO Antenne не несет никакой ответственности за неисправности,

произошедшие в результате неправильного монтажа. Привлекайте

обученный и опытный персонал для оказания помощи в установке,

техническом обслуживании, сборке или разборке. Свяжитесь с вашим

местным установщиком для консультации или помощи, в случае

необходимости.

1. Е сл и В ы у ст а н а вли ва йт е а нт ен ну в п е рв ый р аз , н ай ди те

профессионального помощника. Ваш дилер может объяснить Вам способ

установки антенны в зависимости от типа и размера антенны.

ус т а н о в к а д а н н о г о у с т р о й с т в а в о з л е

высоковольтных линий электропередачи опасна

для жизни! Следуйте прилагаемой инструкции!

ВНИМАНИЕ

INSTALOWANIE ANTEN W POBLIŻU LINII WYSOKIEGO

NAPIĘCIA JEST NIEBEZPIECZNE !

N E M A N I P U L U J T E S A N T E N O U P O B L I Z

ELEKTRICKEHO VEDENI !

ATENCION

UWAGA

VAROVANI

Alle Artikel, die auf der Verpackung oder der

Gebrauchanweisung dieses Symbol tragen, dürfen nicht in

den normalen Mülltonnen entsorgt werden, sondern müssen

an gesonderten Sammelstellen abgegeben werden. Dort

werden die Materialien entsprechend ihrer Eigenschaften

getrennt und, um einen Beitrag zum Umweltschutz zu liefern,

wiederverwertet.

Todos los artículos que exhiban este símbolo en el cuerpo

del producto, en el embalaje o en el manual de instrucciones

del mismo, no deben ser desechados junto a los residuos

urbanos normales sino que deben ser depositados en los

centros de recogida especializados. En estos centros, los

materiales se dividirán en base a sus características y serán

reciclados, para así poder contribuir de manera importante a

la protección y conservación del medio ambiente.

ОСНОВНЫЕ ИНСТРУКЦИИ ПО УСТАНОВКЕ АНТЕННЫ НА

МАЧТУ

в) наденьте рубашку или куртку с длинными рукавами, обувь на

резиновой подошве, а также используйте резиновые перчатки.

2. Заземлите мачту медным проводом с сечением не менее 6 кв. мм.

3. Установите антенну, обращая внимание на правильность сборки и

надежность затяжки болтов и гаек.

Во время установки антенны ПОМНИТЕ:

а) не используйте металлическую лестницу;

ПОМНИТЕ: высоковольтные ЛЭП, а также телефонные и другие

кабельные линии находятся под напряжением, которое опасно для

жизни!

3. Если собираемая часть начинает падать немедленно отойдите в сторону и

не препятствуйте падению. Помните, что антенна, мачта, кабель и

металлические провода являются проводниками электрического тока.

Даже легкое касание любой из составных частей антенной системы к

открытому источнику электроэнергии может привести к короткому

замыканию или поражению электрическим током.

5. Не находитесь вблизи антенны во время передачи.

6. Рекомендуется использовать максимально разрешенную мощность

передачи в соответствии с законодательством.

4. Если необходимо (районы с повышенными ветряными нагрузками или

слишком длинная мачта) используйте специальные противоветровые

направляющие.

б) не работайте во влажную и ветряную погоду;

1. Внимательно следуйте инструкции по установке антенны.

7. Наклейте этикетку “ ” упакованную вместе с антенной на мачту, на DANGER

4. Если одна из частей устанавливаемой антенной системы в результате

падения или по другой причине соприкоснулась с источником

эл ект р о эн ер ги и , НЕ ПЫ ТА ЙТЕСЬ САМ ОСТОЯТЕЛЬНО

УСТРАНИТЬ ЭТО, ПОЗВОНИТЕ В АВАРИЙНУЮ СЛУЖБУ!

Sendemodusist.

7. Kleben Sie das der Antenne beiliegende selbstklebende Etikett “DANGER” in

Augenhöhe an Ihren Mast.

6. Es wird empfohlen, die gesetzlich fesgelegte maximale Leistung des Funkgerätes nicht

zu überschreiten.

SAFETY INFORMATION SHEET ID416 Rev.C

ID442, pag 1/4

Gain-Masterä HW is a Half Wave high tech

fiberglass base station antenna for 10m to 11m

amateur band made of telescopic fiberglass tubes.

Engineered with the most advanced available

technologies it is completly manufactured in Italy

with high quality materials. The design of the

radiant element works like a central feeded dipole

so all RF currents on the radiator are in-phase and

the ground plane radials are not necessary. The

coaxial coil at the bottom works like RF-choke for

the optimum decoupling from mast and feeding

line.

HI-QUALITY ANTENNAS MADE IN ITALY.

antenne

SIRIO

antenne

SIRIO

Gain-Masterä is a registered Trade Mark of SIRIO antenne s.r.l.

WARNING

INSTALLATION OF THIS PRODUCT NEAR POWER

LINES IS DANGEROUS. FOR YOUR SAFETY AND

BEFORE YOU BEGIN INSTALLATION, READ THE

S E PAR AT E S A F E T Y I N F O R M AT I O N S H E E T.

Radiation

Frequency Range

Materials

Mechanical Data

Type

Max Power

Wind Resistance

Electrical Data

Polarization

Height (approx.)

Packaging Dimensions

Weight (approx.)

Mounting mast

Impedance

Connector

Banwidth @ SWR 2.0£

Max Gain on the horizon

0.5 center feeded vertical dipolel

27.2 - 30 MHz (see tunable table pag.3)

1.8 MHz @ 27.2 MHz

Linear Vertical

0 dBd

50 W

500 Watts (CW) continuous

UHF-female, PTFE insulator & gold

plated central pin

Omnidirectional

Whip made of white fiberglass three

sections composite tube,

radiator made of copper wire and low

loss coax cable, stainless steel hardware,

anodized AW6060 aluminium,

UV stabilized thermoplastic

up to 160 Km/h; 100 mi/h

5560 mm; 18.2 ft with bracket

2.6 Kg; 5.7 lb

1950x100x130 mm; 77x4x5 in

side mast with “V” bolt

Æ Æ 35-54 mm; 1.4-2.1in

ID442, pag 2/4

Gain-Masterä is a registered Trade Mark of SIRIO antenne s.r.l.

HI-QUALITY ANTENNAS MADE IN ITALY.

antenne

SIRIO

ITALIANO ENGLISH

Come mostrato in Fig.1 il segnale RF proveniente dal

generatore percorre il cavo coassiale della bobina d'arresto,

quindi prosegue lungo lo stilo fino ad arrivare alla

terminazione della linea coassiale (centro di fase

dell'antenna). Da questo punto la parte di segnale presente

sul conduttore centrale si propaga lungo la metà superiore

della parte radiante mentre le correnti RF, che viaggiavano

all'interno della schermatura del cavo, fuoriescono scorrendo

all'esterno della schermatura e ridiscendono verso la bobina

d'arresto dove l'elevata impedenza della bobina fa si che si

arrestino (funzionamento equivalente ad un dipolo

alimentato nel suo centro).

E' realizzata e assemblata completamente in Italia con i

migliori materiali disponibili, a partire dallo stilo che è

realizzato in tre sezioni da 1.92m di tubi telescopici compositi

in fibra di vetro con parete a triplo strato che rende Gain-

Masterä HW molto più resistente e rigida rispetto alle

concorrenti.

Può essere tarata nella banda da 27.2 a 30 MHz tramite

tabella di sintonia.

Gentile Cliente, vogliamo ringraziarla per aver acquistato un

antenna SIRIO Gain-Masterä HW, siamo sicuri che le darà

grandi soddisfazioni perché è stata progettata con le più

avanzate tecnologie attualmente disponibili ed è costruita

interamente in Italia con materiali di elevata qualità.

Gain-Masterä è il concentrato di quarant'anni di esperienza

nel campo delle antenne che ci ha permesso di sviluppare

prodotto unico che rimarrà uno standard di riferimento per

molti anni a venire.

Come funziona Gain-Masterä HW

In Fig.2 è illustrata la distribuzione di corrente di SIRIO Gain-

Masterä HW. La parte radiante si comporta come un dipolo

alimentato al centro, di conseguenza tutte le correnti RF

risultano in fase e concordi tra loro. Questo accorgimento ci

ha permesso di avere un diagramma di irradiazione identico

ad un dipolo con il suo massimo del segnale nel piano

orizzontale. Gain-Masterä HW presenta quindi il massimo

guadagno ottenibile per un'antenna 1/2l e grazie al suo

angolo di radiazione perfettamente orizzontale permette i

migliori collegamenti possibili.

Altri vantaggi di Gain-Masterä HW sono:

Non necessita di radiali ground plane in quanto è un antenna

bilanciata che funziona come un dipolo alimentato al centro.

Grazie alla sua bobina di arresto (RF-Choke) posta alla base,

Gain-Masterä HW risulta perfettamente disaccoppiata dalla

sua struttura di sostegno (pali, tralicci, etc.) con il beneficio di

mantenere inalterati sia l'impedenza che il diagramma di

irradiazione.

Accetta una potenza massima continuata di 500Watts RMS.

Dear Customer, we thank you for purchasing a SIRIO Gain-

Masterä HW antenna, we are sure you will give great

satisfaction because it was designed with the most advanced

technologies currently available and it's entirely built in Italy

with high quality materials.

Thanks to it's cable coil (RF-Choke) at the base, Gain-

Masterä HW is fully decoupled from its supporting structure

(poles, towers, etc.) with the benefit of preserving both the

impedance that the radiation pattern.

It does not require ground plane radials because it is a

balanced antenna that function as a centre-fed dipole.

Gain-Masterä HW is the result of four decades of experience

in the antennas field; that allowed this unique product that will

remain a standard reference for many years to come.

As shown in Fig.1 the RF signal started from the generator

run through the coaxial cable of the choke coil, then continue

along the first part of the whip until it meet the termination of

the coaxial line (antenna phase centre).

Fig.2 shows the current distribution of SIRIO Gain-Masterä

HW. The design of radiant element behaves as a centre-fed

dipole, hence all currents are in phase.

Other Gain-Masterä HW advantages are:

At this point, the signal on the inner conductor propagates

along the upper half of the radiation element. The RF current

travelling inside the cable shield, protruding outside the

screen and descend toward the choke coil where the high

impedance stop it (in fact, it's equivalent to a centre-fed

dipole).

It makes Gain-Masterä HW much more durable and rigid

then the competitors.

It accepts a maximum continuous power of 500Watts RMS.

How Gain-Masterä HW works

This arrangement allowed us to have a radiation pattern

equal to a dipole which has its maximum gain on the horizon.

Gain-Masterä HW has the highest available gain for 1/2l

antenna and due to its angle of radiation perfectly horizontal,

enables the best possible connections.

It's completely made and assembled in Italy with the finest

materials available, starting from the whip which is carried out

in three sections of 1.92m telescopic tubes with triple-layer

fibreglass.

It can be tuned in the range from 27.2 to 30MHz using the

tuning table.

TYPICAL S.W.R. RESPONSE

Model: Gain-Master HW

S.W.R.

1.0

1.2

1.8

1.4

2.2

1.6

2.0

2.4

2.6

2.8

3.0

26.2 27.2 28.2

f.(MHz)

File: F-01-031

1.8 MHz band @ SWR=2

TUNING TABLE

NOTE: Use the table just as a guide. For

fine-tuning please use an SWR-meter

Low Loss

Coaxial RF choke

Electrical Length

1/2 or 0,5 l

To RF generator

ID442, pag 3/4

# Check if the equipments (CB radio and SWR-meter) work

properly. Make use of owner’s manual for assistance in

operating it.

# Check the coaxial cable and all its connections. Be sure that

the cable is not pinched, shorted, broken or kinked.

# Be sure that the antenna is installed at least 3 meters above

the roof of the nearest building and 5-6 meters above or

away from any metal objects in the area.

SUGGESTION: We recommend to assemble the antenna on

a flat ground open area. Use a good coax cable like BELDEN

H1000R, AIRCOM PLUS or RG-213 as short as possible to

get the best performance and we recommend to mount your

antenna at minimum 3 meters above the roof, as far as

possible from walls, power lines and other antennas.

SAFETY FIRST: YOU CAN BE KILLED IF THIS ANTENNA

COMES NEAR ELECTRIC POWER LINES. BEFORE

DOING INSTALLATION, READ THIS MANUAL AND THE

SUPPLIED SEPARATE SAFETY MULTI LANGUAGE

INFORMATION SHEET.

TROUBLESHOOTING: Gain-Master HW is a tunable

antenna. It is factory checked one by one. If you are unable to

obtain an accettable SWR reading from your antenna, follow

these suggestions to try to solve the problem.

Schematic diagram

Fig.1 Fig.2

RF current

Gain-Masterä is a registered Trade Mark of SIRIO antenne s.r.l.

HI-QUALITY ANTENNAS MADE IN ITALY.

antenne

SIRIO

Gain-Masterä HW Technical Informations

Parts List

Pos Q.ty Part No Description

11 SL06600 Wired coaxial radiator

2 1 - Bottom section with coil

3 1 MA18016 Ø 35x60 plastic sleeve

41 CF02117 15.4x19x1920 fiberglass tube

1CF02217 19.5x23.5x1920 fiberglass tube

2FA00200 Ø 16-27mm AISI316 hose clamps

81TE07300 Ø 18.8x17 radiator fixing part

91VT05900 M4x6 AISI304 set screw cone point

10 1 CH00800 2 mm Allen key

11 1TE05616 Ø 18.8 PVC top cap

12 1IE560/USA self-adhering “DANGER” label

13 2VT01300 M6x20 AISI304 exagonal head screw

14 2 ST04500 Extruded aluminium bracket

15 2 TI03100 M6x188 AISI304 V-bolt

16 6DA01400 M6 AISI304 hexagonal nut

6 RO04200 M6 AISI304 spring lock washer

In order to avoid excessive stress and possible damages to your

GainMaster, we recommend to make use of bracing rods for the

installation in hazardous areas such as:

- Locations subjected to strong wind or constant gusts of wind (eg:

coast and mountain areas).

- Locations with cold winter conditions and frequent formation of ice

layers on the antenna body. In fact, the different distribution of the

weight, can change substantially the resistance to the wind.

We therefore recommend at least 3 ties "NYLON" bracing to be fixed

at the junction between 2° and 3° fiber pipe (see drawing).

ATTENTION: Important for a proper installation

Frequency (MHz)

27.2

27.5

28.0

10m band 28.5

29.0

29.5

30.0

1611

1783

1734

L = (mm)

1820

1692

1647

1550 29.0 ÷ 31.0 MHz

26.3 ÷ 28.1 MHz

27.1 ÷ 28.9 MHz

28.5 ÷ 30.5 MHz

28.0 ÷ 30.0 MHz

26.6 ÷ 28.4 MHz

27.6 ÷ 29.4 MHz

Band @ SWR=2

1 FA02400 Ø 24-40mm AISI316 hose clamps

Sigillare entrambi i

connettori con nastro

adesivo in PVC

Seal both connectors

with electrical

PVC tape

ATTENZIONE!

Non piegare o schiacciare

il cavo coassiale

ATTENTION!

Do not bend or pinch

the coaxial cable.

Avvitare i connettori

BEN SERRATI!

Screw on the connectors

WELL LOCKED!

B Copyright SIRIO antenne - Technical Data are subjected to change - Printed in ITALY - Rev. 20/11/2023 - Cod. ID442, pag. 4/4

Gain-Masterä is a registered Trade Mark of SIRIO antenne s.r.l.

HI-QUALITY ANTENNAS MADE IN ITALY.

antenne

SIRIO

Gain-Masterä HW Mounting Instructions

*L1

Strong steel mast

Æ 35-54mm (not supplied)

17 13

Fase/Step 1

Fase/Step 2 Fase/Step 3

Fase/

Step 5

Fase/Step 4

Robusto palo di montaggio

Æ 35-54mm (non fornito)

· Inserire il manicotto 3

in battuta contro il tubo

in fibra inferiore 2 e

collegare il cavo 1.

Insert the sleeve 3

against the lower fiber

tube 2 and connect

the cable 1.

· Inserire i tubi sul cablaggio

Insert the tubes on wiring

· Scegliere la frequenza

di lavoro dalla Tabella di

Taratura a pag.3 e

la lunghezza *L

corrispondente.

Posizionare il tubo

4 sporgente *L e il

tubo 5 sporgente

*L1= *L-30mm

Choose the

working frequency

from the Tuning Table

on page 3 and the

*L corresponding.

Place tube 4 protruding

*L and the tube 5

protruding *L1= *L-30mm

· Serrare le fascette

6 e 7 fino al bloccaggio

dei tubi in fibra 4, 5 e 2.

Coppia max 3Nm

ATTENZIONE: un

serraggio eccessivo

può provocare crepe e

danni ai tubi in fibra.

Tighten the clamps 6

and 7 up to the locking

of the fibererglass

tubes 4, 5 and 2.

Tightening torque

3Nm max

CAUTION: A

over-tightening it may

cause cracks and damage

at the fiberglass tubes.

*L = see Tuning Table pag.3

*L1 = *L - 30mm

· Tagliare il cavo in eccesso

Cut the extra cable

· Installare il cappuccio in PVC

Instal the PVC cap

· Infilare parte 8 sul cavo fino in battuta

Insert part 8 on cable until it stops

· Tendere il cavo quindi farlo

rientrare di 1÷1.5cm.

NOTA: IL CAVO NON

DEVE ESSERE TESO

Pull up the cable then

return down 1÷1.5cm.

REMARK: THE CABLE

MUST NOT BE TIGHT

· Bloccare con forza

il cavo con vite 9 e

chiave 10

Lock strongly the

cable with screw

9 and key 10

1÷1.5cm

· Applicare

l’etichetta

DANGER in un

punto visibile

Apply the

DANGER

sticker in a

visible point

n. 1 tape rules (meter)

n. 1 screwdriver flat point

n. 1 10 mm open jaw wrench

n. 1 plier

n. 1 electrical PVC tape

n. 1 nippers

Mounting needed tools:

Sirio Antenne Gain Master HW Manuale utente

Marca: Sirio Antenne

Modello: Gain Master HW

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Sirio Antenne Gain Master HW User manual
français: Sirio Antenne Gain Master HW Manuel utilisateur

Sirio Antenne Gain Master HW Manuale utente

Sirio Antenne Gain Master HW Manuale utente

in altre lingue

Documenti correlati

Altri documenti