ProLights LED Fresnel FC and Tunable White Manuale utente

USER MANUAL

MANUALE UTENTE

ECLFRESNELTW

EN - IT

FRESNEL PROJECTOR

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.06-08/19

1

ECLFRESNELTW

Packing content

• ECLFRESNELTW

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Introduction

1. 1 Description and specications1. 1 Description and specications

1. 2 Operating elements and connections1. 2 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX addressing3. 4 DMX addressing

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Linking3. 6 Linking

3. 7 Screen3. 7 Screen

3. 8 Advanced3. 8 Advanced

3. 9 Information3. 9 Information

3. 10 Master/Slave mode3. 10 Master/Slave mode

3. 11 Eects mode3. 11 Eects mode

3. 12 Static mode3. 12 Static mode

3. 13 Manual mode3. 13 Manual mode

3. 14 DMX channels3. 14 DMX channels

3. 15 Connection of the DMX line3. 15 Connection of the DMX line

3. 16 Construction of the DMX termination3. 16 Construction of the DMX termination

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting4. 2 Trouble shooting

2

3

5

6

7

8

11

12

13

14

15

22

23

ECLFRESNELTW

2

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

3

ECLFRESNELTW

- 1 - INTRODUCTION

1.1 DESCRIPTION

ECLFRESNELTW is an advanced LED replacement of traditional 1K Fresnel lamps. Oering 6 colour mixing,

delivering high precision reproduction of the white spectrum from 2.800 K to 10.000 K with high CRI and

an extensive colour reproduction.

The optical system harnesses the power of a 260 W custom LED with 6 colours to create an evenprojec-

tion, beautiful colours and precise white, with the option to apply +/- green and magenta correction to

match other sources of light.

Featuring HD dimming andtuning from 2.800 Kto 10.000 K version, the ECLFRESNELTW delivers the per-

formance and quality of output demanded from this level of luminaire.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 260W 6 colour custom LEDs source (red, orange, green, royal blue, blue, lime)

• CT: 2.800 K ~10.000K

• CRI: > 95

• R9: > 90

• Luminous ux: 7’938lm

• Lux: (15°) 6’517 lx - (45°) 930lx @3 m full

• Source life expectancy: >50.000 h

OPTICS

• Zoom: 15° - 45° manual

• Field angle: 29° - 67°

• Lens diameter: 8’’ - 200mm

• Lens type: Fresnel zoom lens

• Focus: manual

COLOUR SYSTEM

• Colour mixing: tunable white + colour

• CTC: CTC control through independent DMX channel, + / - green and magenta correction and amber

shift activation by DMX

• White presets: 2.800 K -10.000K

• Colour wheel: virtual colour wheel with presets

• Macros: several pre-build macros with adjustable speed

DYNAMIC EFFECTS

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of intensity, CT, colour correction from knob

• Auto mode: built-in programs with execution speed adjustment

• Special features: linear crossfade from a white to any color and CTO applied on colors

BODY

• Hardware on-board: included lter frame, 8 doors barndoor, omega bracket spigot

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: DMX512, RDM, local knob

• DMX channels: 1 / 2 / 5 - 1 / 5 - 2 / 7 / 9 / 12 / 13 / 16 / 19 / 21channel

• RDM: RDM ready for xture remote monitor and settings

ECLFRESNELTW

4

Fig.1Technical drawing

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

• Other: 16bit control of dimmer and colour

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: 4 dierent dimming curves available

• Strobe / shutter: 1 - 30 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free frequency with adjustable PWM

• Selectable PWM: 600 ~ 25.000 Hz

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 260W

• Power consumption (at 120 V): 260W

• Output (at 230 V): 11 units on a single power line

• Output (at 120 V): 6 units on a single power line

• Power factor: pF 0,99 @120 V - pF 0,93 @230 V

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and xing: hanging bracket suitable for safe hanging and positioning

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Power connection: Neutrik powerCON TRUE1 IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 283x440x343mm

• Weight: 7,5kg

283

440

343

6

55

11

3

4

2

7

9

8

10 11 12

5

ECLFRESNELTW

1.2 OPERATING ELEMENTS AND CONNECTIONS

1. AIR OPENING

2. LOCKING KNOB for mounting bracket

3. MOUNTING BRACKET

4. TRACK-ADAPTER(optional)

5. HANDLE

6. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them

7. FOCUS AND ZOOM ADJUSTING SCREW to

zoom the projected image clearly

8. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only

9. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable.

10. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C

11. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C

12. POWER OUT (PowerCON OUT): power output

for connection of multiple units in series.

Fig.2

Fig.4

A B

ECLFRESNELTW

6

- 2 - INSTALLATION

2.1 MOUNTING

ECLFRESNELTW may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the

bracket if is necessary.

Fig.5

7

ECLFRESNELTW

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(g.5).

MENU

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

MENU

1 CONNECT

ð

DMX Address

ð

Value (001-512) Default: 001

DMX Mode

ð

1CH

ð

Amber Shift on

Default: 19CH

Color

Temperature

ð

CTO 2800 - 10000K

Hue (025~025)

Default: 2800K

Color Picker

ð

3200K

71

97

100

...

777

Default: 3200K

Customization

ð

Red (000~255)

Orange (000~255)

Green (000~255)

Royal Blue (000~255)

Blue (000~255)

Lime (000~255)

Default: 255

2CH

ð

Amber Shift on

Color

Temperature

ð

CTO 2800 - 10000K

Hue (025~025)

Default: 2800K

Color Picker

ð

3200K

71

97

100

...

777

Default: 3200K

Customization

ð

Red (000~255)

Orange (000~255)

Green (000~255)

Royal Blue (000~255)

Blue (000~255)

Lime (000~255)

Default: 255

5CH1

5CH2

7CH1

7CH2

ð

Color Picker

ð

No Action

3200K

71

97

100

...

777

8CH

9CH

12CH

13CH

16CH

19CH

21CH

2 SETUP

ð

Screen

ð

Back Light

ð

On

10 s

20 s

30 s

Default: 10 s

Flip Display

ð

No-Yes Default: No

Key Lock

ð

No-Yes Default: No

ECLFRESNELTW

8

3.3 MENU STRUCTURE

3 ADVANCED

ð

Full On Mode

ð

HB

Studio

Default: Studio

Dimmer Mode

ð

O

Dimmer 1

Dimmer 2

Dimmer 3

Default: O

White Balance

ð

O

Adjust

ð

Red (125~255)

Orange (125~255)

Green (125~255)

Royal Blue (125~255)

Blue (125~255)

Lime (125~255)

Default: O

Led Frequency

ð

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Default: 1200Hz

Fan Mode

ð

Auto

On

O

Silent

Default : Auto

Factory Reload

ð

No-Yes No-Yes Default: No

4 INFORMATION

ð

Fixture TIme

ð

0-9999

Version

ð

V1.0

UID

ð

15D0021F****

5 STAND ALONE

ð

Master/Slave

ð

Master

Slave

Default : Slave

Eects

ð

Eect1

Eect2

Eect3

Eect4

ð

(1~100) Default: Eect4

Speed=100

CCT

HSI

Color Tempera-

ture

ð

2800K

3000K

3200K

3400K

3600K

3800K

4000K

4200K

4400K

4600K

4800K

5000K

5200K

5400K

5600K

5800K

6000K

6200K

6400K

6800K

7000K

7200K

7400K

7600K

7800K

8000K

8200K

8400K

8600K

8800K

9000K

9200K

9400K

9600K

9800K

10000K

ð

Dimmer (000~255)

Hue (025~025)

Default : 6000K

Dimmer=255

Hue=0

9

ECLFRESNELTW

Fixed Color

ð

R

O

G

RB

B

L

R.0

R.G

R.RB

R.B

R.L

O.G

O.RB

O.B

O.L

G.RB

G.B

G.L

RB.B

RB.L

B.L

R.O.G

R.O.RB

R.O.B

R.O.L

R.G.RB

R.G.B

R.G.L

R.RB.B

R.RB.L

R.B.L

O.G.RB

O.G.B

O.G.L

O.RB.B

O.RB.L

O.B.L

G.RB.B

G.RB.L

G.B.L

RB.B.L

R.O.G.RB

R.O.G.B

R.O.G.L

R.O.RB.B

R.O.RB.L

R.O.B.L

R.G.RB.B

R.G.RB.L

R.G.B.L

R.RB.B.L

O.G.RB.B

O.G.RB.L

O.G.B.L

O.RB.B.L

G.RB.B.L

R.O.G.RB.B

R.O.G.RB.L

R.O.G.B.L

R.O.RB.B.L

R.G.RB.B.L

O.G.RB.B.L

R.O.G.RB.B.L

ð

Dimmer (000~255) Default:

R.O.G.RB.B.L

Dimmer=255

Color Picker

ð

3200K

71

97

100

101

102

103

104

105

106

107

110

111

113

115

116

117

118

119

120

121

122

124

126

128

130

132

134

135

136

137

138

139

141

144

147

151

152

156

157

158

161

164

165

166

170

174

179

180

181

182

195

197

198

200

201

202

203

204

205

206

702

730

777

ð

Dimmer (000~255) Default: 3200K

Manual Color

ð

Red

Orange

Green

Royal Blue

Blue

Lime

ð

(000~255) Default:

RGBW=255

ECLFRESNELTW

10

11

ECLFRESNELTW

3.4 DMX ADDRESSING

To set DMX addressing follow the instructions below:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Connect. Press the ENTER button to conrm.

• Press UP/DOWN button to select DMX Address. Press the ENTER button to conrm.

• Press UP/DOWN button to select the desired value 001-512. Press the ENTER button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the ECLFRESNELTW with a light controller, adjust the DMX start address for the rst DMX

channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX chan-

nel, adjust the start address 33 on the ECLFRESNELTW. The other functions of the light eect panel are then

automatically assigned to the following addresses.

3.5 DMX CONFIGURATION

The ECLFRESNELTW has dierent DMX channels congurations available selectable through the control

panel.

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Connect. Press the ENTER button to conrm.

• Press UP/DOWN button to select DMX mode. Then press the ENTER button to conrm.

• Press UP/DOWN button to select the desired conguration (1CH, 2CH 2, 5CH1, 5CH2, 7CH1, 7CH2, 8CH , 12CH ,

13CH, 16CH, 19CH, 21CH); then press the ENTER button to save.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

The tables on page 15, 16, 17, 18, 19, 20, 21 indicate the operating mode and DMX value. The ECLFRESNELTW

is equipped with 5-pole XLR connections.

3.6 LINKING

Several units may be interconnected; follow the instructions below:

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 22).

. . . . . . . . . . . .

DMX Address: 33 DMX Address: 48DMX Address: 38 DMX Address: 43

Fig.6 - Example 5 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

ECLFRESNELTW

12

Number

DMX channels

Address of

start (example)

Address of

start (example)

Next possible start address

for unit n ° 1

Next possible start address

for unit n ° 2

Next possible start

address for unit n ° 3

1 33 33 34 35 36

2 33 33-34 35 37 39

5 33 33 - 37 38 43 48

7 33 33 - 39 40 47 54

8 33 33 - 40 41 49 57

9 33 33 - 41 42 51 60

12 33 33 - 44 45 57 69

13 33 33 - 45 46 59 72

16 33 33 - 48 49 65 81

19 33 33 - 51 52 71 90

21 33 33 - 53 54 75 96

3.7 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button to access

the next menu.

• Press UP/DOWN button to select Screen and press the ENTER button to proceed.

• Select the proposed option and press the ENTER button to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically the back-

lighting of the display after a certain time which can be set using the directional keys. To have the

display always on select On or set a value between those shown (10s, 20s, 30s) to turn o the display

once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function, No to

deactivate it.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or

No to deactivate it.

• Press the ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.8 ADVANCED

You can change the parameters for the device by following these steps:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select the Advanced. Press the ENTER button to conrm.

• Press UP/DOWN button to select the desired option and press the ENTER button to conrm:

- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the

13

ECLFRESNELTW

- maximum value of the colours) or Studio mode with a automatic white balance.

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

- White Balance - To balance the white on each colour. Select the colour (Red, Orange, Green, Royal Blue,

Blue and Lime) and the value (125-255) using the UP / DOWN button and press the ENTER button to

conrm.

- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the UP /

DOWN button and press ENTER to conrm the selection.

- Fan Mode - Fan Speed. Select the fan speed (Auto, On, O, Silent) using the UP / DOWN button.

- Factory Reload - To reset the unit. Select Yes or No and select the UP / DOWN button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.9 INFORMATION

To view all the information on the device, proceed as follows:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Information, then press the ENTER button to access the next menu.

• Press UP/DOWN button to scroll through the menu, then select one of the following informationa and

press the ENTER button to display it.

- Fixture Time - To view the operating time of the projector.

- Software Version - To view the rmware version will show on the display.

- UID - To view the identication ID for the RDM control.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.10 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Press the button MENU so many times until the display shows Stand Alone, then press the ENTER button

to select Master/Slave.

• Press UP/DOWN button to select the desired mode and then press ENTER to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

• Set the slaves to the same DMX modes.

3.11 EFFECTS MODE

This xture has a built-in automatic program. To access this, please see the below instructions:

• To enter the Eects mode, press the ENTER button to access the menu.

• Press UP/DOWN button to select Stand Alone, then select Eect. Press ENTER to conrm

• Press UP/DOWN button to select the desired program Eect 1, Eect 2, Eect 3, Eect 4, then press ENTER

to conrm.

• Set the value (1 - 100), then press the ENTER button to conrm.

ECLFRESNELTW

14

3.12 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button.

• Select Fixed Color through the UP/DOWN buttons, then press the ENTER button.

• Set the colors R , O, G, W, RB, B, L, R.O.G.RB.B.L... R.G.RB.B.L, O.G.RB.B.L, R.O.G.RB.B.L through the UP/DOWN but-

tons, then press the ENTER button.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.13 MANUAL MODE

This mode allows to combine the colours (Red, Orange, Green, Royal Blue, Blue and Lime).

• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button.

• Using UP/DOWN buttons Select Static, then press ENTER.

• Select Manual Color through the UP/DOWN buttons, then press the ENTER button.

• Select the colour Red, Orange, Green, Royal Blue, Blue and Lime through the UP/DOWN buttons, then press

the ENTER button.

• Using UP/DOWN buttons, select the desired colour value 000 - 255.

• Press the ENTER button to continue to the next colour Red, Orange, Green, Royal Blue, Blue and Lime.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

1

DIMMER

0~100% 000 - 255

2 CHANNELS

MODE

FUNCTION DMX

Value

2 Ch

1

DIMMER

0~100% 000 - 255

2

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

5 CHANNELS 1

MODE

FUNCTION DMX

Value

5 Ch1

1

DIMMER

0~100% 000 - 255

2

CTO

2800K - 3000K

3000K - 3200K

3200K - 3400K

3400K - 3600K

3600K - 3800K

3800K - 4000K

4000K - 4200K

4200K - 4400K

4400K - 4600K

4600K - 4800K

4800K - 5000K

5000K - 5200K

5200K - 5400K

5400K - 5600K

5600K - 5800K

5800K - 6000K

6000K - 6200K

6200K - 6400K

6400K - 6600K

6600K - 6800K

6800K - 7000K

7000K - 7200K

7200K - 7400K

7400K - 7600K

7600K - 7800K

7800K - 8000K

8000K - 8200K

8200K - 8400K

8400K - 8600K

8600K - 8800K

8800K - 9000K

9000K - 9200K

9200K - 9400K

9400K - 9600K

9600K - 9800K

9800K - 10000K

000 - 007

007 - 014

014 - 021

021 - 028

028 - 035

035 - 042

042 - 049

049 - 056

056 - 063

063 - 070

070 - 077

077 - 084

084 - 091

091 - 098

098 - 105

105 - 112

112 - 119

119 - 126

126 - 133

133 - 140

140 - 147

147 - 154

154 - 161

161 - 168

168 - 175

175 - 182

182 - 189

189 - 196

196 - 203

203 - 210

210 - 217

217 - 224

224 - 231

231 - 238

238 - 245

245 - 255

3

HUE

0

-25°~25°

000 - 000

001 - 255

4

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

5

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

15

ECLFRESNELTW

3.14 DMX CHANNELS

5 CHANNELS 2

MODE

FUNCTION DMX

Value

5 Ch2

1

DIMMER

0~100% 000 - 255

2

DIMMER FINE

0~100% 000 - 255

3

CTO

2800K - 3000K

3000K - 3200K

3200K - 3400K

3400K - 3600K

3600K - 3800K

3800K - 4000K

4000K - 4200K

4200K - 4400K

4400K - 4600K

4600K - 4800K

4800K - 5000K

5000K - 5200K

5200K - 5400K

5400K - 5600K

5600K - 5800K

5800K - 6000K

6000K - 6200K

6200K - 6400K

6400K - 6600K

6600K - 6800K

6800K - 7000K

7000K - 7200K

7200K - 7400K

7400K - 7600K

7600K - 7800K

7800K - 8000K

8000K - 8200K

8200K - 8400K

8400K - 8600K

8600K - 8800K

8800K - 9000K

9000K - 9200K

9200K - 9400K

9400K - 9600K

9600K - 9800K

9800K - 10000K

000 - 007

007 - 014

014 - 021

021 - 028

028 - 035

035 - 042

042 - 049

049 - 056

056 - 063

063 - 070

070 - 077

077 - 084

084 - 091

091 - 098

098 - 105

105 - 112

112 - 119

119 - 126

126 - 133

133 - 140

140 - 147

147 - 154

154 - 161

161 - 168

168 - 175

175 - 182

182 - 189

189 - 196

196 - 203

203 - 210

210 - 217

217 - 224

224 - 231

231 - 238

238 - 245

245 - 255

4

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

5

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

7 CHANNELS 1

MODE

FUNCTION DMX

Value

7 Ch1

1

RED

0~100% 000 - 255

2

ORANGE

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

ROYAL BLUE

0~100% 000 - 255

5

BLUE

0~100%

000 - 255

6

LIME

0~100% 000 - 255

7

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

7 CHANNELS 2

MODE

FUNCTION DMX

Value

7 Ch2

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

ORANGE

0~100% 000 - 255

4

GREEN

0~100% 000 - 255

5

ROYAL BLUE

0~100% 000 - 255

6

BLUE

0~100%

000 - 255

7

LIME

0~100% 000 - 255

ECLFRESNELTW

16

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

1

COLOR PICKER

No Funciton

3200K

71

97

100

101

102

103

104

105

106

107

110

111

113

115

116

117

118

119

120

121

122

124

126

128

130

132

134

135

136

137

138

139

141

144

147

151

152

156

157

158

161

164

165

166

170

174

179

180

181

182

195

197

000 - 000

001 - 003

004 - 007

008 - 011

012 - 015

016 - 019

020 - 023

024 - 027

028 - 031

032 - 035

036 - 039

040 - 043

044 - 047

048 - 051

052 - 055

056 - 059

060 - 063

064 - 067

068 - 071

072 - 075

076 - 079

080 - 083

084-087

088 - 091

092 - 095

096-099

100 - 103

104 - 107

108 - 111

112 - 115

116 - 119

120 - 123

124 - 127

128 - 131

132 - 135

136 - 139

140 - 143

144 - 147

148 - 151

152 - 155

156 - 159

160 - 163

164 - 167

168 - 171

172 - 175

176 - 179

180 - 183

184 - 187

188 - 191

192 - 195

196 - 199

200 - 203

204 - 207

208 - 211

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

198

200

201

202

203

204

205

206

702

730

777

212 - 215

216 - 219

220 - 223

224 - 227

228 - 231

232 - 235

236 - 239

240 - 243

244 - 247

248 - 251

252 - 255

2

DIMMER

0~100% 000 - 255

3

RED

0~100% 000 - 255

4

ORANGE

0~100% 000 - 255

5

GREEN

0~100% 000 - 255

6

ROYAL BLUE

0~100% 000 - 255

7

BLUE

0~100%

000 - 255

8

LIME

0~100% 000 - 255

17

ECLFRESNELTW

12 CHANNELS

MODE

FUNCTION DMX

Value

12 Ch

1

DIMMER

0~100% 000 - 255

2

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

3 RED 000 - 255

4 ORANGE 000 - 255

5 GREEN 000 - 255

6 ROYAL BLUE 000 - 255

7 BLUE 000 - 255

8 LIME 000 - 255

9

CTO

2800K - 3000K

3000K - 3200K

3200K - 3400K

3400K - 3600K

3600K - 3800K

3800K - 4000K

4000K - 4200K

4200K - 4400K

4400K - 4600K

4600K - 4800K

4800K - 5000K

5000K - 5200K

5200K - 5400K

5400K - 5600K

5600K - 5800K

5800K - 6000K

6000K - 6200K

6200K - 6400K

6400K - 6600K

6600K - 6800K

6800K - 7000K

7000K - 7200K

7200K - 7400K

7400K - 7600K

7600K - 7800K

7800K - 8000K

8000K - 8200K

8200K - 8400K

8400K - 8600K

8600K - 8800K

8800K - 9000K

9000K - 9200K

9200K - 9400K

9400K - 9600K

9600K - 9800K

9800K - 10000K

No Funciton

000 - 007

007 - 014

014 - 021

021 - 028

028 - 035

035 - 042

042 - 049

049 - 056

056 - 063

063 - 070

070 - 077

077 - 084

084 - 091

091 - 098

098 - 105

105 - 112

112 - 119

119 - 126

126 - 133

133 - 140

140 - 147

147 - 154

154 - 161

161 - 168

168 - 175

175 - 182

182 - 189

189 - 196

196 - 203

203 - 210

210 - 217

217 - 224

224 - 231

231 - 238

238 - 245

245 - 252

253 - 255

9 CHANNELS

MODE

FUNCTION DMX

Value

9 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

ORANGE

0~100% 000 - 255

4

GREEN

0~100% 000 - 255

5

ROYAL BLUE

0~100% 000 - 255

6

BLUE

0~100%

000 - 255

7

LIME

0~100% 000 - 255

8

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

9

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

ECLFRESNELTW

18

La pagina si sta caricando...

ProLights LED Fresnel FC and Tunable White Manuale utente

Questo manuale è adatto anche per

ProLights LED Fresnel FC and Tunable White Manuale utente

in altre lingue

Documenti correlati

Altri documenti