ProLights MOSAICOJR Manuale utente

USER MANUAL

MANUALE UTENTE

MOSAICOJR

EN - IT

OUTDOOR LED PROJECTOR

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-07/19

1

MOSAICOJR

Packing content

• MOSAICOJR

• Power adapter cable

• Signal adapter cable (2 pcs)

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

2. 2 Mounting with optional bracket

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX Addressing

3. 5 DMX Mode

3. 6 Wireless

3. 7 Screen

3. 8 Fixture settings

3. 9 Auto test

3. 10 Manual test

3. 11 Advanced

3. 12 Information on the device

3. 13 Operations in automatic mode

3. 14 Color wheel and Rotating gobos

3. 15 DMX control

3. 16 Connection of the DMX line

3. 17 Construction of the DMX termination

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

4. 3 Gobos replacement

2

3

5

6

7

8

9

11

12

13

14

19

22

23

24

MOSAICOJR

2

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modiﬁcations on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system ﬁtted with eﬃcient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

3

MOSAICOJR

- 1 - INTRODUCTION

1.1 DESCRIPTION

MOSAICOJR is a compact IP rated LED gobo projector designed for the projection of logos, images and

textures onto commercial buildings, hotels and city facades. The small size allows for mounting anywhere

without any impact on the surrounding environment or architecture. The onboard zoom ranges from

14° to 44° allowing for an extensive user-ﬂexibility, from projecting crisp and accurate logos to textured

projections.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 70W white LED

• CT: 7.900K

• Luminous ﬂux: (14°) 2’861 lm - (44°) 2’681lm

• Lux: (14°) 6’070 lux - (44°) 848lx @3 m

• Lux: (14°) 2’250 lux - (44°) 315lx @5 m

• Source life expectancy: > 50.000 h

OPTICS

• Zoom: 14° - 44° motorised linear zoom

• Lens diameter: 63mm

• Lens type: high-quality glass lens optics

• Focus: motorised

COLOUR SYSTEM

• Colour wheel: 7 dichroic ﬁlters + open

DYNAMIC EFFECTS

• Rotating gobos: 7 rotating gobos + open, indexing

• Gobo size: gobo Ø 15,8 mm - img Ø 12,7 mm - 1,10 mm

• Auto mode: built-in programs with execution speed adjustment

• Special features: record scenes and create chases and shows throughout these scenes

BODY

• Hardware on-board: on board mechanics for rigging to the ceiling

• Body: aluminium die-casting

• Body colour: cool gray 6C

CONTROL

• Protocols: DMX512, RDM, W-DMX

• DMX channels: 8 / 14channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for ﬁxture remote monitor and settings

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

MOSAICOJR

4

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: 4 diﬀerent dimming curves available

• Strobe / shutter: 1 - 21 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -20° ~ +45°

• Flicker: ﬂicker free frequency with adjustable PWM

E

LECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): (static) 86,5 W - (dinamic) 91,3W

• Power consumption (at 120 V): (static) 85 W - (dinamic) 84,4W

• Output (at 230 V): 23 units on a single power line

• Output (at 120 V): 13 units on a single power line

• Power factor: pF 0,98 @230 V - pF 0,99 @120 V

PHYSICAL

• Cooling: forced air with IP low noise fan

• Sospension and ﬁxing: hanging bracket suitable for safe hanging and positioning

• Adaptors: XLR and Shuko 16A adaptors included

• Signal connection: moulded IP signal IN/OUT connectors

• Data connection: W-DMX receiver

• Power connection: moulded IP power IN/OUT connectors

• IP rating: 66 for outdoor installations

• Dimensions (WxHxD): 247x258x244mm

• Weight: 10kg

247

258

244

Fig.1Technical drawing

5

MOSAICOJR

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. MOUNTING BRACKET

2. 2x HEXAGONAL HEAD SCREW SYSTEMS for

tighten the bracket.

3. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

4. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C.

5. GORE VALVE

6. POWER IN: for connection to a socket

(100-240V~/50-60Hz) via the supplied mains

cable.

7. POWER OUT: connect to supply power to the

next unit

8. CONTROL PANEL with display and 4 button

used to access the control panel functions and

manage them.

Fig.2

Rear panel

3

1

2

4

8

5

6

7

2

MOSAICOJR

6

- 2 - INSTALLATION

2.1 MOUNTING

MOSAICOJR may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For ﬁxing, stable mounting clips are required. The mounting place must be of suﬃcient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the ﬁxture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the

bracket if is necessary.

1

2

Fig.3

7

MOSAICOJR

Fig.4 - Example with poles with square cross-section of 150x150 mm

2.2 MOUNTING WITH OPTIONAL BRACKET

MOSAICOJR bracket for wall mounting and suspension on poles with square cross-section with diam-

eter from 50x50 mm to 150x150mm or circular cross-section with diameter from 50 mm to 150 mm.

Complete kit of nuts and bolts included.

• Check that all accessories have been

supplied with the product before

installation. The manufacturer is not

responsible for any damage or loss

of accessories after opening the in-

ner packaging.

• Do not use the product for purposes

other than those described.

• When mounting / using the moun-

ting bracket, be sure to avoid dama-

ging the product and causing safety

hazards.

• Do not mount the bracket on a ver-

tical support whose surface shows

deformations, injuries, crushing, etc.

• Make sure all screws, bolts, nuts are

fully tightened.

• Make sure that no external force is

applied to the installed product.

• Locate the position of the optional

MOSUNIBRACKJR bracket at a suit-

able height..

• Both the bracket and the MOSAI-

COJR must be secured with a safety

rope.

MOSAICOJR

8

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch oﬀ, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and oﬀ via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(ﬁg.4).

MENU

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or confirm the

current function value or

option within a menu

Fig.4 - Functions of the buttons

9

MOSAICOJR

3.3 MENU STRUCTURE

MENU

1

CONNECT

ð

DMX Address

ð

Value (1-512) Default: 1

DMX Mode

ð

8 CH

14 CH

Default: 8CH

Wireless On/Off

ð

On/Off Default :Off

Reset

ð

Yes/No Default :No

WDMX To DMX

ð

Yes/No Default :No

2 SET UP

ð

Screen

ð

Backlight

ð

On

10s

20s

30s

Default: 10s

Flip Display

ð

Yes/No Default :No

Warn Cue

ð

On/Off Default:On

Key Lock

ð

Yes/No Default :No

Fixture

ð

Fan mode

ð

Auto/High/Silent Default: Auto

Temp unit

ð

C°/F° Default: °C

Auto Test

ð

Auto Test

Manual Test

ð

Shutter

Dimmer

Color

Gobo

RGobo

Focus

Zoom

ð

Value (000-255) for each

function

Default:

Dimmer=255

Shutter = 255

3 ADVANCED

ð

Reset

ð

All

Color

Gobo

Focus

Zoom

ð

Yes/No

Adjust

(password: 050)

ð

Color Oﬀset

Gobo Oﬀset

RGobo Oﬀset

Focus Oﬀset

Zoom Oﬀset

ð

Value (000-255) for each

function

Factory Reload

ð

Yes/No

4

INFORMATION

ð

Fixture Time

ð

0-9999 Default: 0

Temperature

ð

58 °C

Fans Speed

ð

**%

Software

Version

ð

DISP: V1.0

CTR1:V1.0

UID

ð

15D00231****

MOSAICOJR

10

5 STAND ALONE

ð

Play

ð

Off

Show

ð

Show 1

...

Show 3

Default:

Show 1

Chase

ð

Chase 1

...

Chase 8

Default:

Chase 1

Scene

ð

Scene 1

…

Scene 32

Default:

Scene 1

Edit

Show

ð

Show 1

Show 2

Show 3

ð

Chase 1(On-Off) - Chase 8(On-Off)

Default: Oﬀ

Edit

Chase

ð

Chase 1

Chase 2

Chase 3

Chase 4

Chase 5

Chase 6

Chase 7

Chase 8

ð

Step 1-16

Oﬀ - Scenes1-32

Default: Oﬀ

Edit

Scenes

ð

Edit Scenes 01

Edit Scenes 02

Edit Scenes 03

......

Edit Scenes 30

Edit Scenes 31

Edit Scenes 32

ð

New/Edit Scene

ð

Shutte/Dimmer/Color/

Gobo/RGobo/Focus/Zoom

Default:

Dimmer: 255

Shutter: 255

Focus: 128

Zoom: 128

All others

at 0

Copy Scene

ð

Oﬀ

Scenes 01

Scenes 02

Scenes 03

......

Scenes 30

Scenes 31

Scenes 32

Scenes

Record

ð

Scenes 01

Scenes 02

Scenes 03

......

Scenes 30

Scenes 31

Scenes 32

ð

*

DMX - Scenes Record

Slave

setup

ð

Edit Scenes 01

Edit Scenes 02

......

Edit Scenes 30

Edit Scenes 32

ð

RGobo, Focus, Zoom Default:

RGobo: 0

Focus: 128

Zoom: 128

11

MOSAICOJR

Scenes Time

ð

Scenes 01 Time

Scenes 02 Time

Scenes 03 Time

......

Scenes 30 Time

Scenes 31 Time

Scenes 32 Time

ð

Fade in Time

Hold Time

Fade out Time

ð

0-3600 s Default: 1S

Chase Time

ð

Chase 1 Time

Chase 2 Time

Chase 3 Time

Chase 4 Time

Chase 5 Time

Chase 6 Time

Chase 7 Time

Chase 8 Time

ð

0-3600 s Default: 1S

Move blackout

ð

Scene 01

Scene 02

Scene 03

......

Scene 30

Scene 31

Scene 32

ð

Oﬀ-On

3.4 DMX ADDRESSING

To enter the DMX mode, follow these steps:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Connect, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conﬁrm the setting.

• Press the MENU button repeatedly to exit the menu and save changes.

To able to operate the MOSAICOJR with a light controller, adjust the DMX start address for the ﬁrst a DMX

channel. If the address 33 on the controller is provided for controlling the function of the ﬁrst DMX chan-

nel, adjust the start address 33 on the MOSAICOJR. The other functions of the light eﬀect panel are then

automatically assigned to the following addresses.

An example with the start address 33 is shown in ﬁg.5.

3.5 DMX MODE

The MOSAICOJR has 2 DMX channel conﬁgurations which can be accessed from the control panel.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Connect, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to

enter the next menu.

• Use the UP/DOWN button to select the desired DMX channel conﬁguration (8 CH,14CH), then press the

ENTER button to conﬁrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

NOTE: through the 14CH mode it is possible to edit or store scenes inside the projector.

MOSAICOJR

12

Number

DMX

channels

Address of

start (example)

Address of

start (example)

Next possible start address

for unit n ° 1

Next possible start address

for unit n ° 2

Next possible start address

for unit n ° 3

8 33 33-40 41 49 57

14 33 33-46 47 61 75

DMX512 Controller

. . . . . . . . . . . .

Fig.5 - Example 8 DMX channels configuration

DMX Address: 33 DMX Address: 57DMX Address: 41 DMX Address: 49

3.6 WIRELESS

• To enter the Wireless mode proceed in the following mode:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Connect, then press the ENTER button to enter the

next menu.

• Select the Wireless function using the UP/DOWN buttons, then press the ENTER button.

• To activate the Receive function, use the UP/DOWN buttons and select the On option.

• Press the ENTER button to conﬁrm the selection.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

NOTE - Once you have performed these steps, you must synchronize with any WiFi unit with which you

want to communicate by pressing the sync button on it. At this point connect the DMX console to the

WiFi unit to open the communication with the MOSAICOJR.

• To reset the unit, select the Receive Reset function using the UP/DOWN buttons, press the ENTER button

until the display shows Connect, then select Receive Reset using the UP/DOWN buttons, then press the

ENTER button.

• To activate the mode use the UP / DOWN keys and select the Yes option.

• Press the ENTER button to conﬁrm the selection.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

• To activate the Wireless to DMX function, use the UP / DOWN buttons to press the ENTER button until the

display shows Connect, then select Wireless to DMX, then press the ENTER button.

• To activate the mode use the UP/DOWN buttons and select the Yes option.

• Press the ENTER button to conﬁrm the selection.

• Press the MENU key repeatedly to exit the menu and to save the changes made.

13

MOSAICOJR

3.7 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button ac-

cess the next menu.

• Press the UP/DOWN button to select Screen and press the ENTER button to proceed.

• Select the proposed option with the UP/DOWN button and press the ENTER button to conﬁrm.

- Backlight - Auto Oﬀ display backlight. This function allows you to switch oﬀ automatically the back-

lighting of the display after a certain time which can be set using the directional keys. To have the

display always on select On or set a value between those shown (10s, 20s, 30s) to turn oﬀ the display

once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function, No to

deactivate it or AUTO.

- Warn Cue - Warning of error. Use the arrow keys to select Oﬀ or On depending on whether or not the

display shows error warnings.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or

No to deactivate it.

• Press the ENTER button to conﬁrm the selection.

• Press the MENU key repeatedly to exit the menu and to save the changes made.

3.8 FIXTURE SETTINGS

You can change the parameters for the device by following these steps:

• Press the button MENU to enter the menu mode.

• Use the buttons UP/DOWN to select Set Up. Press the button ENTER to conﬁrm.

• Use the buttons UP/DOWN to select Fixture. Press the button ENTER to conﬁrm.

• Press the buttons UP/DOWN to select the desired option and press the button ENTER to conﬁrm:

- Fan Mode - Fan speed. Select the desired fan speed Auto, Silent, High through the button UP/ DOWN.

- Temperature unit. Select Temperature unit function and then choose Celsius / Fahrenheit measurement unit

then press the ENTER button to conﬁrm the selection.

• Press the MENU key repeatedly to exit the menu and to save the changes made.

3.9 AUTO TEST

Allow checking the proper functioning of the unit. Start the automatic test in the following way:

• Press the button MENU to enter the menu mode.

• Use the buttons UP/DOWN to select the Set Up. Press the button ENTER to conﬁrm.

• Press the buttons UP/DOWN to select the Auto Test and press ENTER to conﬁrm.

• To conﬁrm and start the automatic test press the ENTER button.

3.10 MANUAL TEST

It allows to do adjustments on the eﬀects through commands panel to obtain a perfect balance between

the projectors.

• Press the button MENU to enter the menu mode.

• Press the buttons UP/DOWN to select the item Set Up. Then press the button ENTER.

MOSAICOJR

14

• Press the buttons UP/DOWN to select the Manual Test. Then press the button ENTER.

• Select the eﬀect you want change (Shutter, Dimmer, Color, Gobo, RGobo, Focus, Zoom). Then press the button

ENTER to conﬁrm.

• Use the directional buttons to calibrate the eﬀect setting a value between 0 ~ 255. Then press the button

ENTER to conﬁrm.

• Press the MENU key repeatedly to exit the menu and to save the changes made.

3.11 ADVANCED

It is possible to modify the following parameters following the same procedure:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Advanced, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select one off the following parametres:

- Reset - To start a preset program to restore the selected function (All, Color, Gobo, Focus, Zoom).

- Adjust - To allows you to change all parameters. Insert the password "050" to enter. Select the desired

function (Color Oﬀset, Gobo Oﬀset, RGobo Oﬀset, Focus Oﬀset, Zoom Oﬀset) and the choose the value (0 ~ 255).

- Factory Reload - To reset the unit. Select Yes or No and select ENTER to confirm.

• Press the ENTER button to confirm the selection and wait for the selected function to be restored.

• Press the MENU key repeatedly to exit the menu and to save the changes made.

3.12 INFORMATION ON THE DEVICE

To view all the information on the device, proceed as follows:

• Press the MENU button to access the main menu. Press the UP/DOWN button to select Information, then

press the ENTER button to access the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - To view the operating time of the projector.

- Temperature - To view the temperature of the device in °C/°F on the display.

- Fans Speed - To view on the display the fan speed present near the lamp.

- Software Version - To view the firmware version will show on the display.

- UID - To view the identiﬁcation ID for the RDM control.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.13 OPERATIONS IN AUTOMATIC MODE

Play Show

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Show and press ENTER to conﬁrm your

choice.

• Press the UP/DOWN button to select the mode of operation: Show 1, Show 2, Show 3.

• Press the ENTER button to conﬁrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

15

MOSAICOJR

The unit will go into automatic mode by executing the program automatically.

Play Chase

The function Chase lets you choose the automatic program to actually run.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Chase and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Chase 1 ~ Chase 8 and press ENTER

to confirm.

• Press the MENU button repeatedly to exit the menu and save changes.

Play Scenes

The function Scenes lets you choose the scene to actually run.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Scenes and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Scene 1 ~ Scene 32 and press ENTER

to confirm.

• Press the MENU button repeatedly to exit the menu and save changes.

Edit Show

The function Edit Show allows you to create individual scenes to be included in the Chase Step.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Show and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Show 1/Show 2/Show 3, then press the

ENTER button to confirm.

• Press the UP/DOWN button to scroll through the menu, select Chase 1 ~ Chase 8, then press the ENTER

button to confirm.

• Press the UP/DOWN button to change the value of the function, then press the ENTER button to

confirm.

• Press the MENU button repeatedly to exit the menu and save changes.

Edit Chase

The function Edit Chase allows you to create automatic pre-programmed show.

The automatic programs Chase1 ~ Chase8. Each Chase can be composed of 1 ~ 16 step that can be configured

through the following procedure:

• Press the MENU button to access the main menu.

MOSAICOJR

16

• Press the UP/DOWN button to scroll the menu, select the Stand Alone, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Chases and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Chase 1 ~ Edit Chase 8, then press the

ENTER button to confirm.

• Press the UP/DOWN button to select the Step 01 ~ Step 16, and press ENTER to confirm.

• Press the UP/DOWN button to select the Scene 1 ~ 32 you want to set for the Step chosen, and then press

ENTER to confirm.

• Press the MENU button repeatedly to exit the menu and save changes.

Edit Scenes

The function Edit Scenes allows you to create individual scenes to be included in the Chase Step.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scenes and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scene 1 ~ Edit Scene 32, then press the

ENTER button to confirm.

• Then choose the desired function: New / Edit Scene or Copy Scene.

• Press the UP/DOWN button to select the desired function you want to edit (Shutter, Dimmer, etc.), Then

press the ENTER button to confirm.

• Press the UP/DOWN button to change the value of the function, then press the ENTER button to

confirm.

• Press the MENU button repeatedly to exit the menu and save changes.

Scenes Record

The Scenes Record function allows the recording of MOSAICOJR scenes through the console on which the

ﬁxture was stored in Scene Record, capable of driving the beacon functions expressed in DMX.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Stand Alone, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Scenes Record and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select the scene to edit in the automatic program, then press the ENTER

button to conﬁrm. After pushing ENTER button, MOSAICOJR will wait for the conﬁrm.

• From the DMX console, change the parameters of the MOSAICOJR based on the scene to be created.

• After creating the scene, press ENTER on the MOSAICOJR (the message STORED will appear).

• Press the MENU button repeatedly to exit the menu and save changes.

Slave Setup

The function Slave Setup allows you to execute automatic pre-programmed show set on the master

projector.

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button

to enter the next menu.

17

MOSAICOJR

• Press the UP/DOWN button to scroll through the menu, select Slave Setup and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scene 1 ~ Edit Scene 32, then press the

ENTER button to confirm.

• Press the UP/DOWN button to select the desired function you want to edit (RGobo, Focus, Zoom), Then

press the ENTER button to confirm.

• Press the UP/DOWN button to change the value of the function, then press the ENTER button to

confirm.

• Press the MENU button repeatedly to exit the menu and save changes.

NOTE: if the Slave units have to do the same operation as the MASTER, during a recording, the values of

Focus, Zoom and RGobo will not be stored. These values must be adjusted manually on the Slave units, via this

section.

Scenes Time

The Scenes Time function allows you to set the input, duration and output times of each single scene.

• Press the ENTER key to access the main menu.

• Press the UP / DOWN button to scroll through the menu, select Stand Alone, then press the ENTER button

to access the next menu.

• Press the UP / DOWN button to select Scenes Time and press the ENTER button to access the next menu.

• Press the UP / DOWN button to select Scene 01 Time ~ Scene 32 Time, then press the ENTER button.

• Press the UP / DOWN button to change the following times, then press the ENTER button to conﬁrm:

- Fade in Time - Scene entry time.

- Hold Time - Time duration of the scene.

- Fade Out Time - Time out of the scene.

• Press the MENU key several times to exit the menu and to save the changes made.

Move blackout

The Move Blackout function allows you not to display the scroll between one scene and another; any kind of

change between a scene and the next occurs “in the dark”.

• Press the ENTER key to access the main menu.

• Press the UP / DOWN button to scroll through the menu, select Stand Alone, then press the ENTER button

to access the next menu.

• Press the UP / DOWN button to select Move Blackout and press the ENTER button to access the next menu.

• Press the UP / DOWN button to select On or Oﬀ then press the ENTER button.

• Press the MENU key several times to exit the menu and to save the changes made.

When the projector is in Stand Alone it turns out to be MASTER, as well as if you enter or connect the projec-

tor to the DMX. When you exit the menu or disconnect the DMX connection, the projector restarts the

show execution from the last scene interrupted by these two actions.

MOSAICOJR

18

3.14 COLOR WHEEL

ROTATING GOBOS

SLOT6: ORANGE

OPEN

SLOT1: DARK RED

SLOT2: DARK

BLUE

SLOT7: CTO

SLOT3: YELLOW

SLOT4: GREEN

SLOT5: MAGENTA

1

2

3

4

5

6

7

La pagina sta caricando ...

ProLights MOSAICOJR Manuale utente

ProLights MOSAICOJR Manuale utente

in altre lingue

Documenti correlati

Altri documenti