DTS JACK Manuale utente

D.T.S. Illuminazione srl

[email protected] http://www.dts-lighting.it

Via Fagnano Selve 10/12/14

47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111

Made in Italy

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 7

6- IMPORTANT SAFETY INFORMATION 8

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects

7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT 10

8- VOLTAGE AND FREQUENCY 11

9- INSTALLATION 11

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 13

10.1 Protection

11- DMX SIGNAL CONNECTION 14

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 15

13- DISPLAY FUNCTIONS 16

14- ERROR MESSAGES 20

15- HIDDEN MENU 21

15.1 Calibration mode

16- PAN SPEED & TILT SPEED 22

17- BASE FANS SPEED AND BASE LAMP SPEED 22

18- OPENING THE PROJECTOR HOUSING 23

19- REPLACING GOBOS 23

20- PERIODIC CLEANING 24

20.1 Lenses and reflectors

20.2 Fans and air passages

21- PERIODIC CONTROLS 25

22- DMX PROTOCOL 26

23- 9 MOTORS CONTROL CARD 38

24- PAN & TILT CARD 39

25- DISPLAY CARD 40

26- LAMP ON-OFF CONTROL CARD 40

27- ROTATING GOBO WHEEL 41

28- ROTATING GOBO PROVIDED INTO THE UNIT BOX 41

29- FIXED GOBO WHEEL 42

30- COLOUR WHEEL 43

4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC

SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE

UNIT ON INFLAMMABLE SURFACES”

THIS SYMBOL MEANS “RADIATION FROM

THIS LAMP CAN CAUSE DAMAGE TO EYES

AND SKIN”

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE

DEVICE AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or

overheating.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

!

F

UV

2M

5

4- TECHNICAL FEATURES

The JACK is a high-power, compact, lightweight moving head.

JACK features a wide excursion motorized zoom allowing any application from

long-throw projections to large wall washing.

Beam opening is:

1° - 2,5° 'Beam' projection;

2,5° - 37° 'Spot' projection;

38° - 46° 'Wash' projection.

JACK generates a huge luminosity and extremely uniform projection using only a

189 W lamp; power consumption is just 230W.

Also, JACK comes equipped with the 'FPR' ( 'Free Pan Rotation' - patent pending )

system, which allows limitless pan rotation, in either direction, never having to reverse

motion (Cod. 03.MS012.EBLFP).

JACK is the perfect moving head for rental companies – who want a quick and easy to

install unit – thanks to its compactness and light weight (only 11,9 Kg).

JACK is suitable for any professional applications.

JACK

(Cod. 03.MS012.EB.L)

• Electronic ballast 90-260V 50/60 Hz • Black finish

Also available with white finish (RAL 9003) on demand (03.MS012.EB.03.L)

(Cod. 03.MS012.EBLFP)

• Electronic ballast 90-260V 50/60 Hz • FPR (Free Pan Rotation) Black finish

Also available with white finish (RAL 9003) on demand (03.MS012.EB03LFP)

Lamp

MSD Platinum 5R (7.950 Lumens)

Colour temperature: 8.000°K

Type of connection: PINS 2,8x 0,8mm

Optical group

* 50,000 Lux at 5 m (2,5°)

* Improved optical group made with 11 coated lenses

combined with a dichroic glass reflector

* 16-bit motorized linear zoom (2,5°- 46°)

* Beam opening: 1°- 46°

* 16-bit motorized focus

* Motorized iris

* Linear dimmer / shutter / strobe (0,85 flash/sec to 10 flash/sec)

Colour generation

* 18-colour wheel with linear selection for perfect 2-colour beams

Dynamic effects

Overlapping wheels for multiple effects:

* Customizable rotating gobo wheel (9 gobos)

* Customizable fixed gobo wheel (10 gobos)

* 4-facet rotating prism

6

4- TECHNICAL FEATURES

Interface / Control / Programming

* LCD graphic display (control / management / monitoring of the main parameters)

* 4 soft-keys (control / management / monitoring of the main parameters)

* Controlled via DMX 512 standard digital communication protocol

* RDM

* ARTNET (available on request)

* Wireless ready

* Internal operating system updatable via D.T.S. RED BOX interface and

hyperterminal program on windows based PC

DMX

25 DMX channels (default) or 17 DMX channels

Pan & Tilt

Jack FPR (Cod. 03.MS012.EBLFP)

* 'FPR': limitless pan rotation, in either direction, never having to reverse motion

Tilt 270° (1,5 sec.)

Jack (Cod. 03.MS012.EB.L)

* Pan 540° (2,5 sec.); Tilt 270° (1,5 sec.)

* New Tri-phase stepper motor technology for ultra-fast and silent Pan &Tilt

movements

* 16-bit movement resolution

* Selectable speed ranges

Power supply

* Electronic ballast; 90-260 V 50/60 Hz

* Power consumption: 230 W with PFC

Energy saving

* Power saving mode (the lamp dims to 80% after shutter closure)

Connectors

* DMX: 4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik;

* Power supply: POWERCONN connectors (Power In / Power Out) by Neutrik

Operating ambient temperature

-10° / 40°

Weight

11,9 Kg

Internal safety devices

* Overvoltage circuit protection and overtemperature circuit protection

International certifications

Safety: EN 60598-1: 1993

EN 60598-2-17: 1989

A1-A3: 1993

EMC: EN 55015

7

4- TECHNICAL FEATURES

Dimensions

Packaging Dimensions (LxWxH) Unit Dimensions (LxWxH)

532 x 430 x 414 mm 350x370x560mm

Weight: 14,4 Kg Weight: 11,9 Kg

5- ACCESSORIES

As standard

* 1 x MSD Platinum 5R (cod. 0505S034)

* 1 x POWERCON male cable connector (cod. 0520P014)

* 1 x XLR 5 Pins male cable connector (cod. 0508B028)

* 1 x XLR 5 Pins female cable connector (cod. 0508B027)

* “C” Clamp G QUICK with “Fast Lock” connection 1/4 turn (one piece) (cod.

0521A014)

* Rotating Gobo Dicro (D.T.S. Code: 0516G063)

* User’s manual

Optional (on request)

• Wireless DMX Receiver Card with INDOOR IP20 omni. 2dBi antenna included

(cod.03.LA.126)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod.

0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod.

0521A010)

300 mm

4

7

0

m

370 mm

217 mm

5

6

0

m

350 mm

270°

8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

JACK uses a MSD Platinum 5R lamp.

The use of any other alternative lamp is not recommended and will null and void the

fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with those of identical value.

Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit.

Unplug the unit prior to performing any function which involves touching the inside of

the moving head, including lamp replacement.

-The level of technology inherent in the JACK requires the assistance of specialised

personnel for all servicing. Please refer to an authorised D.T.S. service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged.

Their respective shielding functions will only operate efficiently if they are in perfect

working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the

failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle

the unit until at least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to

replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the

penetration of solid and liquid objects is IP 20.

For outdoor use, D.T.S. reccomend the use of the dedicated raincovers.

2M

F

UV

!

9

7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT

Warning: Switch off the unit before replacing the lamp.

MSD Platinum 5R

Power 189W

Luminous flux 7950 lm

Colour temperature 8.000°K

Type of connection: PINS 2,8 x 0,8 mm

Rated life 2000 hours

1) Loosen the 2 “¼ turn” screws which fix the head covers (photo 1) .

2) Once loosen the screws, simply lift the covers to access the internal components

(photo 2 and 3).

Photo 1 Photo 2 Photo 3

3) Using a Philips screwdriver, loose the 2 screws A, B, (photo 4), unplug the fan

connector (photo 5) and remove the lamp fan assembly (photo 6).

Photo 4 Photo 5

1/4 TURN

COUNTER

CLOCKWISE

10

Photo 6

4) Loose the four screws which fix the lamp (photo 7), unplug the two fast-on cable

connectors (photo 8) and remove the old lamp.

5) Put in place the new lamp and push it toward the three mechanical ends D, E, F

(photo 9) on the lamp support; this let you have the lamp properly aligned on the

optical system.

Photo 7 Photo 8

WARNING:

Never look directly at the lamp when it‟s lit.

Discharge lamps emits UV rays;

radiation from this lamp can cause

damage to eyes and skin.

Photo 9

UV

D

E

F

11

8- VOLTAGE AND FREQUENCY

The JACK with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

JACK may be either floor or ceiling mounted.

For floor mounting installations, the JACK is supplied with four rubber mounting feet

on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix

the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hang it.

The structure should also be sufficiently rigid so as not to move or shake whilst the

JACK is moving.

Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the

JACK by using the Fast Lock “C” clamps provided in the box.

9.1- Safety cable

We recommend the use of a safety cable or chain connected to the JACK and to the

suspension truss in order to avoid the fixture accidentally falling should the main fixing

point fail.

Make sure that the iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain/cord to the attachment point (A) located on the base

of the fixture, as shown in the picture below.

!

A

SAFETY CHAIN / CORD

ATTACHMENT POINT

12

9.2 Protection against liquids

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

9.3- Movement

JACK FPR (Cod. 03.MS012.EBLFP) Unlimited Pan rotation; Tilt 270° (1,5 sec.)

JACK (Cod. 03.MS012.EB.L) Pan 540° (2,5 sec.), Tilt 270° (1,5 sec.)

DO NOT place any obstructions in the path of the projector's movement.

WARNING

Do not place any object in the

path of the projector’s

movement

Free Pan Rotation („FPR‟) No „FPR‟

(Cod. 03.MS012.EBLFP) (Cod. 03.MS012.EB.L)

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

The minimum recommended distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 2 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans

located on both the base and head of the fixture.

These should, under no circumstances, be blocked or obstructed whilst the projector

is in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should NOT exceed 40°C.

F

2M

!

540°

270°

13

10- MAINS CONNECTION

JACK with electronic ballast operate at 90-260 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 1,5 amps

at 230 VOLT, or 3 amps at 90 VOLT.

Strict adherence to regulatory norms is strongly recommended.

MAINS AC OUTPUT 90-260V 50/60 Hz (16A Max)

(Cod. 03.MS012.EBLFP)

(Cod. 03.MS012.EB.L)

MAINS AC INPUT 90-260V 50/60 Hz

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each JACK.

A good earth connection is essential for the correct operation of the projector.

!

14

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal.

Connection between the mixer and the projector or between projectors must be carried

out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors

has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest

to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N D A R D

D M X 5 1 2

DMX OUT

DMX OUT DMX IN

DMX IN

DMX IN DMX OUT

15

11.1-DMX Addresses

JACK can be used in 2 different DMX modes: 25 DMX control channels (Default) or

17 DMX control channels.

Here below is described the DMX channels addressing for the controller when JACK is

set to 25 and 17 DMX control channels:

25 channels mode (Default)

Projector 1 A001

Projector 2 A026 If you want to select the next projector, just add “25”

Projector 3 A051

….. A….

projector 6 A126

17 channels mode

Projector 1 A001

Projector 2 A018 If you want to select the next projector, just add “17”

Projector 3 A035

….. A….

projector 6 A086

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now setted to the new DMX address.

TRICKS:

If you keep pushed the UP or DOWN keys, the channels are calculated more quickly

and you get a faster selection.

12- FIRMWARE UPDATING

Warning:

This procedure require a base knowledge of computer applications and Windows

Hyperterminal program. Please refer to an authorised D.T.S. service centre.

To update the software version of the JACK you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface.

(The driver and the installation procedure are available in our web site

www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal

program.

It will be possible to download the software from the reserved area of D.T.S. web site:

www.dts-lighting.it.

!

16

13- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The JACK display panel shows all the available functions . Using these functions, it is

possible to change some of the parameters and add some functions. Changing the

D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX

512 used to control it. Carefully follow the instructions below before carrying out any

variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

MENU

ENTER DOWN

UP

DISPLAY

MAINS AC INPUT

90-260V 50 / 60Hz

MAINS AC OUTPUT

90-260V 50 / 60 Hz

(16A Max)

DMX OUT

DMX IN

DMX OUT

DMX IN

03.MS012.EB.L

17

13- DISPLAY FUNCTIONS

Pan Direction Pan movement

Normal or Reversed

PAN DIRECTION Default = Normal

This menu allows to set

the Pan movement.

Normal or Reversed

Tilt Direction Tilt movement

Normal or Reversed

TILT DIRECTION Default = Normal

This menu allows to set

the Tilt movement.

Normal or Reversed

Pan Speed Pan Speed control

(1-8)

PAN SPEED

Pan Speed control (1-8)

Tilt Speed Tilt Speed control

(1-8)

TILT SPEED

Tilt Speed control (1-8)

Up-Down

Menu

Up-DownENTER

Up-Down

Menu

Up-Down

Menu

Up-DownENTER

ENTER

PAN DIRECTION

NORMAL

MENU ENTER DOWN UP

TILT DIRECTION

NORMAL

MENU ENTER DOWN UP

Up-Down

Menu

Up-DownENTER

ENTER

PAN SPEED

8

MENU ENTER DOWN UP

TILT SPEED

8

MENU ENTER DOWN UP

18

13- DISPLAY FUNCTIONS

Display Display Flip

ON THE GROUND

DISPLAY FLIP / STAND BY / CONTRAST (Default)

SUSPENDED

Display Flip:

Reverses display's reading depending on

the mounting position

(On the ground or suspended).

Display Standby

Display Standby: OFF = Display

To turn off the display (after 5 seconds) Standby disabled

or leave it always on. (Default)

ON = Display goes OFF

Display Contrast: after 5 seconds

Display contrast regulation (1-32)

Display Contrast

1-32 (Default = 25)

DMX Mode DMX Mode

17 channels

DMX MODE 25 channels (Default)

To select DMX mode :

17 channels or 25 channels (default)

Lamp BY DMX = Lamp ON / OFF

via DMX (Default)

LAMP ALWAYS ON = Forced ON

Lamp always ON, always OFF, ALWAYS OFF = Forced

lamp ON-OFF selectable via DMX OFF

and lamp life time reset RESET COUNTER = Lamp

life time reset

ADJUST

To adjust the lamp with no mixer

connected. LAMP ADJUST = To adjust

It’s possible to set the parameters the lamp with no mixer

for PAN-TILT, ZOOM and FOCUS connected.

It’s possible to set the

Parameters for PAN-TILT,

ZOOM and FOCUS

Reset ENABLED = Reset

via DMX enabled (Default)

RESET DISABLED = Reset

Reset via DMX ENABLED / DISABLED via DMX disabled

And unit reset NOW = Unit motors reset

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-Down

Menu

Up-Down

Menu

Up-DownENTER

ENTER

DMX MODE

25 channels

MENU ENTER DOWN UP

FLIP

LAMP

FLIP

LAMP

ADJUST

UP

DOWN

ENTER

MENU

BY DMX

MENU ENTER DOWN UP

ENABLED

BY DMX

RESET

MENU ENTER DOWN UP

FLIP

ON THE GROUND

DISPLAY

MENU ENTER DOWN UP

FLIP

STANDBY

OFF

DISPLAY

MENU ENTER DOWN UP

FLIP

CONTRAST

25

DISPLAY

19

13- DISPLAY FUNCTIONS

Base Fans Base Fans speed control

1-12 (Default = 4)

BASE FANS

Base Fans speed control

Lamp Fans Lamp Fans speed control

1-12 (Default = 5)

LAMP FANS

Lamp Fans speed control

Gobo Rotation ON

OFF = (Default)

GOBO ROTATION

Gobo rotation during gobo scrolling

for rotating gobo wheel

Auto Focus ON

OFF = (Default)

AUTO FOCUS (Auto focus function not yet

Automatic focusing implemented)

System info SYSTEM INFO

SYSTEM INFO Lamp life time, lamp strikes,

Lamp life time, lamp strikes, unit life time, 8 motors card

unit life time, 8 motors card software version, Pan&Tilt

software version, Pan&Tilt card card software version and

software version and unit model unit model

Reserved

RESERVED Pan Lock = Lock the Pan

Pan lock-Tilt lock to the desired value

Pan free-Tilt free Tilt Lock = Lock the Tilt to

System Reboot the desired value

(Code = 100) Pan Free = Remove power

to Pan motor

Tilt Free = Remove power

to Tilt motor

System Reboot = Unit

Reboot without needing

of turning OFF the unit

Up-Down

Menu

ENTER

Up-DownENTER

Up-Down

Menu

GOBO ROTATION

OFF

MENU ENTER DOWN UP

During gobo scrolling

RESERVED

000

MENU ENTER DOWN UP

ENTER CODE

PAN LOCK

NO

MENU ENTER DOWN UP

Up-Down

Menu

Up-Down

Menu

Up-Down

Menu

Up-Down

Menu

Up-DownENTER

ENTER

SYSTEM INFO

LAMP LIFE:0024H STRIKE:048

UNIT LIFE: 0024H

9M R.34

PT R.23

MODEL: JACK

MENU ENTER DOWN UP

AUTO FOCUS

OFF

MENU ENTER DOWN UP

BASE FANS

4

MENU ENTER DOWN UP

1=13V 12=24V

LAMP FANS

5

MENU ENTER DOWN UP

1=13V 12=24V

20

13- DISPLAY FUNCTIONS

Default Default

To restore main settings

DEFAULT

To restore main settings

13- DISPLAY FUNCTIONS

14- ERROR MESSAGES

COLOUR WHEEL PAN REPOSITIONING TILT REPOSITIONING

POSITION ERROR ENCODER ERROR ENCODER ERROR

COMMUNICATION DMX GOBO GOBO

PROBLEM BETWEEN ADDRESS WHEEL POSITION

9 MOTORS CARD AND ERROR ERROR ERROR

PAN&TILT CARD

FIXED GOBO WHEEL IRIS ERROR FOCUS ERROR ZOOM ERROR

ERROR

DEFAULT

SURE?

MENU ENTER DOWN UP

RESTORE MAIN SETTINGS

DEFAULT

RESTORE MAIN SETTINGS

MENU ENTER DOWN UP

PRESS ENTER TO CONFORM

PRESS MENU TO CANCEL

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN UP

ERROR

COLOUR WHEEL

MENU ENTER DOWN UP

ERROR

PAN

MENU ENTER DOWN UP

ERROR

TILT

MENU ENTER DOWN UP

ERROR

INTERNAL BUS

MENU ENTER DOWN UP

ERROR

DMX ADDRESS

MENU ENTER DOWN UP

ERROR

GOBO

MENU ENTER DOWN UP

ERROR

GOBO INDEX

MENU ENTER DOWN UP

ERROR

FIXED GOBO

MENU ENTER DOWN UP

ERROR

IRIS

MENU ENTER DOWN UP

ERROR

FOCUS

MENU ENTER DOWN UP

ERROR

ZOOM

La pagina sta caricando ...

DTS JACK Manuale utente

DTS JACK Manuale utente

in altre lingue

Documenti correlati

Altri documenti