Teclumen Spot 575 TM3 Manuale utente

Spot 575 TM3 Spot 575 TM3

GB

User Manual Rel 1.0

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della Teclumen

Teclumen si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o

di design a ciascun proprio prodotto. Teclumen non assume alcuna responsabilità sull’uso o

sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from Teclumen

Teclumen reserves the right to make any aesthetic, functional or design modifications to any of its

products without prior notice. Teclumen assumes no responsibility for the use or application of the

products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de Teclumen

Teclumen se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles

ou de design, sans préavis, à chacun de ses produits. Teclumen décline toute responsabilité sur

l'utilisation ou sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de Teclumen

Teclumen se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. Teclumen no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

ARC 1200

Spot 575 TM3

2

ARC 1200

3

INDEX:

1- TECHNICAL FEATURES 4

2- IMPORTANT SAFETY INFORMATION 5

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against ultraviolet radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3- MOUNTING THE LAMP 6

3.1 Lamp alignment

4- VOLTAGE AND FREQUENCY 7

5- INSTALLATION 7

5.1 Safety cable

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6- MAINS CONNECTION 8

6.1 Protection

7- DMX SIGNAL CONNECTION 9

7.1 DMX Addresses

7.2 Selecting the DMX address

8- DISPLAY FUNCTIONS 11

9- AUTOMATIC MODE 14

9.1 Game P

9.2 Rec Mode

10- PAN & TILT SPEED 15

11- FANS SPEED

12- ERROR MESSAGES

13- HIDDEN MENU 16

14- OPENING UP THE PROJECTOR HOUSING 17

15- REPLACING GOBOS

16- PERIODIC CLEANING 18

16.1 Lenses and reflectors

16.2 Fans and air passages

17- PERIODIC CONTROLS

18- DMX PROTOCOLS 19

19- GOBO WHEEL 30

20-COLOUR WHEEL 31

21- MOTORS CONTROL CARD 32

22- PAN & TILT CARD 33

23-CABLES RESEND CARD

24-DISPLAY CARD

25- LAMP ON-OFF CONTROL CARD

26- WIRING DIAGRAM 34

Spot 575 TM3

ARC 1200

4

1- TECHNICAL FEATURES

The Spot 575 TM3 is fitted with a Philips MSR 575/2 discharge lamp

(GX9,5 lampholder base), with a colour temperature of 7,200 °K and a luminous flux of

49,000 Lumens.

Duration is 750 hours, with replacement recommended before 1000 hours

Other recommended lamps: Philips 575 MSD (6.000K°-49.000 Lumens-3.000 hours)

The unit incorporates:

Motorized Focus system

Zoom (3 selectable beam aperture angles 11° / 15° / 18° with auto-focus)

Dimmer (emitted light is controlled by progressive and linear dimming).

Shutter (instantaneous shutter opening/closure)

Strobe: mechanical strobe effect (frequency variable from 0.85 flashes/sec to 10

flashes/sec).

Gobo wheel (7 indexable 16 bit gobos + open)

Colour wheel (8 colours + open)

Prism (indexable 3 facet prism rotating in both directions)

Frost Filter

Electronic or magnetic ballast

Pan: 540° in 3.9 seconds (8 or 16 bit) with auto repositioning system

Tilt: 320° in 2.6 seconds (8 or 16 bit) with auto repositioning system

USITT Standard DMX 512 input

20 DMX channels

4 -eight digit- LED display with 4 buttons

2 XLR connectors (In and Out) with 3 and 5 pins selectable by user

Power supply

Electronic ballast:

Universal power supply 90 - 245 V (50/60 Hz)

Electromagnetic ballast:

230 V 50-60 Hz(Standard)

On request: 100 V 50-60 Hz /120 V 60 HZ / 208 V 60 Hz

Power consumption: 750 W.

Remote Lamp on/off via DMX

Operating ambient temperature -10° / 40°

Weight

26 Kg (Spot 575 TM3 E.B.)

Dimensions (HxDxL)

Projector (670x450x470)

Weight 26 Kg

Packing Dimensions

(HxDxL)

800 x 550 x 440 mm

Weight

33.3 Kg

Spot 575 TM3

ARC 1200

5

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if

there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves

touching the inside of the moving head, including lamp replacement.

-The level of technology present in the Spot 575 TMrequires the assistance of specialised personnel for

all servicing. Please refer to an authorised Teclumen service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective

shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

2.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of

supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main

fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at

least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should

not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

2.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of

solid and liquid matter is IP 20.

Spot 575 TM uses a Philips 575 MSR/2 or MSD

Spot 575 TM3

3- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, remove the 3 screws A,B, C, (photo 1) which fix the lamp holder.

2) Remove the lamp holder assembly (photo2).

3)Insert the lamp (photo 3).

The lamp used on Spot 575 TM3 is made in quartz glass and should be handled with care. Always

follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue

provided in the lamp's packaging. The GX9,5 lamp socket is symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat

the procedure.

4) Replace the lamp assembly and tighten the screws A,B,C, which were previously removed (photo4).

3.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic

filters and other components inside the unit.

Alignment is carried out using the 3 adjusters X, Y and Z.

During this operation you must have a uniform luminosity all around the projected area.

Philips 575 MSR/2

Power 575W

Luminous flux 49,000 lm

Colour temperature 7.200°K

Lampbase GX9,5

Rated life 1,000 hours

6

Photo 2Photo 1 Photo 4Photo 3

Philips 575 MSD

Power 575W

Luminous flux 43,000 lm

Colour temperature 6.000°K

Lampbase GX9,5

Rated life 3,000 hours

Photo 5

Spot 575 TM3

4- VOLTAGE AND FREQUENCY

The Spot 575 TMwith electronic ballast can operate at 90-245 VOLT 50 or 60 Hz.

The Spot 575 TMwith electromagnetic ballast can operate at

5- INSTALLATION

Spot 575 TMmay be either floor or ceiling mounted.

For floor mounting installations, the Spot 575 TMis supplied with four rubber mounting feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the

mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the

unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to

move or shake whilst the Spot 575 TMis moving.

Four quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps

provided in the box, to fix the unit in any position.

.

5.1- Safety cable

We recommend the use of a safety cable or chain connected to the Spot 575 TMand to the suspension

truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the

iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the

picture below.

5.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come

into contact with oil, water or any other liquid. The proper unit functioning would be compromised

should this occur.

230 V 50-60 Hz(Standard)

On request: 100 V 50-60 Hz /120 V 60 HZ / 208 V 60 Hz

7

A

Spot 575 TM3

5.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any

obstructions in the path of the projector's movement.

5.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended

distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 2 MT.

5.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the

base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the

projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

5.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature

should NOT exceed 40°C.

6- MAINS CONNECTION

Spot 575 TMwith electronic ballast operate at 90-245 VOLT 50-60 Hz.

Spot 575 TMwith electromagnetic ballast operate at 230 VOLT 50-60 Hz

Prior to connecting the unit to your mains supply,

ensure that the model in your possession correctly matches

the mains supply available. For connection purposes,

ensure that your plug is capable of supporting 6,3 amps at 208-230V,

Or16 amps at 100-120 V

Strict adherence to regulatory norms is strongly recommended.

6.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each Spt 575 TM3.

A good earth connection is essential for the correct operation of the projector.

7- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the

projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a

CANNON XLR 5 or 3 pins connector.

(On request: 100 V 50-60 Hz /120 V 60 HZ / 208 V 60 Hz)

8

540°

270°

Electronic ballast

90-245V 50 / 60Hz

Electromagnetic ballast

230 V 50/60 Hz (standard)

On request: 100 V 50-60 Hz

120 V 60 HZ / 208 V 60 Hz

Spot 575 TM3

Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it

to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the

second one.

In this way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

The standard configuration of the Spot 575 TM3 is with XLR 5 pins connection.

To convert to an XLR 3 pins configuration proceed as follows:

1) Remove the 2 screws fixing the display cover panel to the unit (photo 1).

2) Remove the screws that fix the XLR connectors to the panel (photo 2).

3) Rotate the electronic card by 180° (photo 3).

4) Place the 3 pins XLR connectors in the special holes and close.

For Installations where long distance DMX cable connections are needed,we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

Photo 2Photo 1 Photo 3

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

STANDARD

DMX 512

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

9

Spot 575 TM3

7.1-DMX Addresses

Spot 575 TM3 can be used in two different modes: 16 or 20 DMX (default) channels.

If you want to use the Spot 575 TM3 in 16 channels mode, select the 16 CH mode from the MODE

menu and set the following addresses on the mixer:

Projector 1 A001

Projector 2 A017 If you want to select the next projector, just add “16”

Projector 3 A033

….. A….

projector 6 A081

If you want to use the Spot 575 TM3 in 20 channels mode, select the 20 CH mode from the MODE

menu and set the following addresses:

Projector 1 A001

Projector 2 A021 If you want to select the next projector, just add “20”

Projector 3 A041

….. A….

Projector 6 A101

7.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will

start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a

faster selection.

10

Spot 575 TM3

DMX IN

DMX OUT

DISPLAY

MAINS

Electronic ballast

90-245V 50 / 60Hz

Electromagnetic ballast

230 V 50/60 Hz (standard)

On request: 100 V 50-60 Hz

120 V 60 HZ / 208 V 60 Hz

8- DISPLAY FUNCTIONS

11

MENU

ENTER

DOWN

UP

DISPLAY FUNCTIONS

The Spot 575 TM3 display panel shows all the available functions . Using these functions, it is

possible to change some of the parameters and add some functions. Changing the Teclumen

setting can vary the functions of the unit so that it does not respond to the DMX 512 used to

control it. Carefully follow the instructions below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Up-DownMENU ENTERUp-Down

PAN MOVEMENT INVERSION

To reverse Pan movement from left

to right and vice versa

Up-Down

Counterclockwise

Clockwise

Up-DownMENU ENTERUp-Down

TILT MOVEMENT INVERSION

To reverse Tilt movement from

bottom upwards and vice versa

Up-Down

Counterclockwise

Clockwise

Up-DownMENU ENTER

DMX MODE

To select DMX mode : 20-16

channels

20 CHANNELS

(Pan & Tilt 16 bit)

16 CHANNELS

(Pan & Tilt 16 bit)

Up-Down

ENTER

Up-Down

MENU

ENTERUp-Down

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position

(On the ground or suspended).

Up-Down

Floor

position

Suspension

position

Up-DownENTER

DISPLAY STAND BY

To turn off the display (after 5 seconds)

Or leave it always on.

Display OFF

Display

always ON

ENTER

Spot 575 TM3

MENU ENTER

TEST MODE

Full test and single function test.

Up-Down

12

Up-Down

MENU

ENTER

DEFAULT

To restore default setting

ENTER

Up-Down

MENU ENTER

Fan control

To control the fan speed .

Up-Down

ENTER

Up-Down

(DEFAULT : 12 )

MENU ENTER

Up-Down

ENTER

Up-Down

(DEFAULT : 2 )

SPEED control

Pan Tilt Speed control.

8- DISPLAY FUNCTIONS

PAN

TILT

DIMMER

SHUTTER

GOBO SHAKE

GOBO

GOBO ROT.

EFFECTS

EFFECTS ROT.

COLOR

FOCUS

ZOOM

ENTER

FROST

MENU

ENTER

AUTOMATIC MODE

Automatic game without DMX

controller

ENTER

Up-Down

ENTER

MENU

Up-Down

ENTER

Pcb 8 motors. Pcb PAN&TILT

MENU

Up-Down

ENTER

GOBO Rotation

Gobo Rotation during gobo scrolling

Up-Down

GOBO ROTATION DISABLE

GOBO ROTATION ENABLE

.

ENTER

MENU

Up-Down

ENTER

FOCUS

Focus stepper motor settings

Up-Down

FOCUS STEPPER MOTOR TYPE 1

FOCUS STEPPER MOTOR TYPE 2

ENTER

ALL

SOFTWARE

Software version

MENU

Up-Down

RESET

Al motors reset

RESET ENABLED VIA DMX

RESET DISABLED VIA DMX

TOTAL RESET

ENTER

Up-Down

Spot 575 TM3

MENU

Up-Down

ENTER

RESERVED

Pan lock-Tilt lock

Pan free-Tilt free

Up-Down

ENTER

.

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

.

ENTER

Up-Down

ENTER

Up-Down

.

ENTER

PAN LOCK

LOCK THE PAN TO THE DESIRED VALUE

TILT LOCK

LOCK THE TILT TO THE DESIRED VALUE

PAN FREE

REMOVE POWER TO PAN MOTOR

TILT FREE

REMOVE POWER TO TILT MOTOR

MENU ENTER

TIMER

lamp life TIME (reset possible)

and total UNIT LIFE TIME (reset not possible)

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

13

8- DISPLAY FUNCTIONS

LAMP

Lamp always ON-always OFF

Or lamp ON-OFF selectable via DMX

ENTER

FORCED ON

ENTER

FORCED OFF

ENTER

ON / OFF VIA DMX (default)

MENU

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ADJUST

To adjust the lamp with no mixer connected.

It’s possible to set the parameters for

PAN-TILT and FOCUS

ENTER

ACC

Lamp strikes counter

ENTER

Up-Down

MENU ENTER

REC

Record mode

ENTER

Up-Down

MENU ENTER

Up-Down

Slave

Slave mode as run by GAM.P, Synchronised with master

ENTER

Up-Down

Spot 575 TM3

9- AUTOMATIC MODE (auto)

Spot 575 TM3 can work in automatic mode without a DMX controller.

First of all connect the projectors with a DMX cable (picture below).

To activate Auto mode on the first unit, use the menu to run through the different modes until AUTO

appears on the display, at this point press enter.

Now it is possible to select the Game P which is user programmable through REC mode.

To confirm game activation press ENTER.

9.1- Game P

The first unit that will function as a Master must be put in (AUTO) mode, the other projectors have to be

put in slave mode (selectable through the menu). This way all units will be synchronised with the master.

Please note that the projectors must be of the same model.

On the master unit it is possible to vary the speed of the GAME P (SPEE)

NB: It is possible to run GAME P on the other units even though these do not have GAME P programmed.

You can do this by setting the units to the same mode as the master is set before programming GAME P

(16CH DMX) and setting the DMX address to A001.

9.2-Rec Mode

It is possible to program your own game on the Spot 575 TM3 that will then run in AUTO mode (GAME P).

Each unit can have its own programmed game.

In REC mode each projector must be set to the same mode (16CH DMX).

For the programming of GAME P besides the channels necessary to control the unit a further 3 DMX

channels are needed. So that in REC mode if the 16CH mode is selected you will need 19 channels for the

program to work correctly.

Connect the unit to a DMX mixer/controller, every unit should be set to its own Address (See the

paragraph on DMX addresses). The projectors can also be of different models:Spot/Wash 575 TM3 ,

Spot/Wash 575tm and Spot/Wash 250tm. When you are in REC mode R.001 appears on the display (DMX

address).

MASTER

ARC 1200

14

OUT IN

OUT

SLAVE 1 SLAVE 2

Spot 575 TM3

The three new DMX channels are:

-Scene channel

-From 0-255 are displayed the programmable scenes (max 16 scenes M.001 M016)

-View channel:

-From 1-19 the unit runs the scene that has been saved in the unit memory and it is possible to

play through the other scenes using the scene channel.

-From 20-235 the unit runs the configuration given by the received input DMX values. With the

channel scene it is possible to pass from one scene to the next,while with REC it is possible to

record the selected scene.

-From 236-255 the unit runs the configuration given by the received DMX values from the projector

in that moment. It is possible to select a scene and then close the GAME P with the REC channel.

-Recording channel (REC)

Records the set scene with a variation from 0 to 255 (the display flashes indicating that the scene has

been recorded).

You must keep the REC channel set to 0 and to run through the 255 only once you have decided to save

the scene. If GAME P is not closed, by indicating the last scene, in playback mode all 16 scenes will be

played through even if not programmed.

You can set the PAN and TILT motors at high speed on your Spot 575 TM3.

Press menu until you see SPEE.

Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.

When you use speed 4 (the highest) PAN and TILT speed is very high and your projector may loose its

path. In this case, the encoder corrects the position.

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be

less than 35° C.

12- ERROR MESSAGES:

10- PAN & TILT SPEED (SPEE) (default: 2)

11- FAN SPEED (FANS)( default: 12)

ERROR: COLOR WHEEL POSITION

ERROR: GOBO WHEEL POSITION

ERROR: ZOOM POSITION

ERROR: GOBO ROTATION POSITION

ERROR: INTERNAL

COMMUNICATION

ERROR: AUTO MODE INPUT

ERROR: ENCODER PAN

ERROR: ENCODER TILT

ERROR: DMX ADDRESS

ERROR: LOAD DATA

EEPROM

ERROR: SENSOR CIRCUIT

COLOR/ZOOM

ERROR: SENSOR CIRCUIT

GOBO/GOBO ROTATION

ERROR: SYNCHRONIZED

FREQUENCY MEASURE

(SYNCHRONISM FOR LAMP ON)

ARC 1200

15

Spot 575 TM3

Up-DownENTER

PAN ALIGNMENT

To align pan

ENTER

Up-DownENTER

TILT ALIGNMENT

To align tilt

ENTER

Up-Down

ENTER

Up-DownENTERUp-Down

GOBO WHEEL ALIGNMENT

To align gobo wheel

ENTER

Up-DownENTER

Up-Down

GOBOROTATION ALIGNMENT

To align gobo ROTATION

ENTER

Up-DownENTERUp-Down

FOCUS ALIGNMENT

To align focus

ENTER

Up-DownENTERUp-Down

COLOR WHEEL ALIGNMENT

To align color wheel

ENTER

Up-DownENTERUp-Down

SHUTTER ALIGNMENT

To align shutter

ENTER

Up-DownENTERUp-Down

PRISM ALIGNMENT

To align prism

ENTER

Up-DownENTERUp-Down

LENSES ALIGNMENT

To align Zoom lenses

ES.

ENTER

ARC 1200

16

13- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the Spot 575 TM3 (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

Electronic calibration of the motors.

Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must

repeat all previous calibrations)

Exit from hidden menu.

16

Spot 575 TM3

17

14- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

15- REPLACING GOBOS

Spot 575 TM3 uses a mechanical system which allows the fixture's gobos to be removed without the use

of special tools. Replacement gobos should be made of either heat resistant glass or metal.

An ever-increasing range of gobos is available from your Teclumen sales network.

Gobo dimensions are as follows:

ø external = 27.9 mm

ø of image with defined edge = 24 mm

thickness = from 0.2 to 4 mm (see catalogue)

Replacing gobos on the rotating gobo wheel

When replacing gobos, ensure that the projector is switched off.

1) Open the projector housing as described above.

2) Remove the gobo holder to allow easier access to the gobo(photo 1 and 2).

3) Release the gobo retaining spring and carefully remove the gobo (photo 3).

4) Reverse the procedure to install a replacement gobo.

Photo 1

Photo 3

Photo 1

Photo 2

Spot 575 TM3

16- PERIODIC CLEANING

16.1- Lenses and reflectors

Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses

and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

16.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning

will depend of course, on the conditions in which the projector is operating. Suitable instruments

for performing this type of maintenance are a brush and a common vacuum cleaner or an air

compressor. If necessary, clean the fans and air passages more frequently.

17- PERIODIC CONTROLS

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will

help to avoid the danger of the lamp exploding.

Mechanical parts

Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them

if necessary. Periodically check the lubrication of all components, particularly the parts subject to

high temperatures. If necessary, lubricate with suitable lubricant, available from your Teclumen

distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors;

refasten them if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the Spot 575 TM3.

Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if

necessary.

Attention

Disconnect mains power prior to removing the projector housing.

18

Spot 575 TM3

16 CHANNELS MODE

1 PAN msb 540°

2 PAN lsb

3 TILT msb 270°

4 TILT lsb

5 SPEED MOVEMENT

6 DIMMER

7 SHUTTER

8 COLOUR

9 COLOUR PROPORTIONAL (Priority in color channel)

10 GOBO

11 GOBO ROTATION

12 PRISM/PRISM ROTATION

13 FOCUS

14 ZOOM

15 FROST (Priority on Zoom channel)

16 LAMP ON-OFF / RESET

18- DMX PROTOCOL

ARC 1200

19

DMX CHANNEL

1

Parameter: PAN msb

DMX CHANNEL

2

Parameter: PAN lsb

DMX CHANNEL

3

Parameter: TILT msb

DMX CHANNEL

4

Parameter: TILT lsb

DMX CHANNEL

5

Parameter: MOVEMENT SPEED

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-10

5

Standard

11-25

18

Fast movement

26-127

76

Vector mode from fast to slow

128-247

187

Variable time reaction to

DMX signal ( fast to slow)

248-255

251

Slow reaction time to DMX

signal

DMX CHANNEL

6

Parameter: DIMMER

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

Spot 575 TM3

-

0-8

4

Black-out

9-255

Proportional dimmer

DMX CHANNEL

7

Parameter: SHUTTER

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-9

5

Black-out

10-23

16

StrobE random speed

24-37

30

Strobe speed 1 min.

38-51

44

Strobe speed 2

52-65

58

Strobe speed 3

66-79

72

Strobe speed 4

80-93

86

Strobe speed 5

94-107

100

Strobe speed 6 max.

108-121

114

Pulse open speed 1 min.

122-135

128

Pulse open speed 2

136-149

142

Pulse open speed 3

150-163

156

Pulse open speed 4 max.

164-177

170

Pulse closed speed 1 min.

178-191

184

Pulse closed speed 2

192-205

198

Pulse closed speed 3

206-219

212

Pulse closed speed 4 max.

220-227

225

Colour and Gobo in black-out

228-233

230

Pan and Tilt in black-out

234-255

244

Open

DMX CHANNEL

8

Parameter: COLOUR

DMX range

Value

Mid point

DMX value

Move

range

(degrees)

Mode Option Function

0-10

5

Colour1

11-21

16

Bicolour ½

22-32

27

Colour2

33-43

38

Bicolour 2/3

44-54

49

Colour3

55-65

60

Bicolour 3/4

66-76

71

Colour4

77-87

82

Bicolour 4/5

88-98

93

Colour5

99-109

104

Bicolour 5/6

110-120

115

Colour6

121-131

126

Bicolour 6/7

132-142

137

Colour7

143-153

148

Bicolour 7/8

154-164

159

Colour8

ARC 1200

20

Spot 575 TM3

La pagina si sta caricando...

Teclumen Spot 575 TM3 Manuale utente

Teclumen Spot 575 TM3 Manuale utente

in altre lingue

Altri documenti