DTS XM 1200 SPOT Manuale utente

Tipo
Manuale utente
XM 1200 SPOTXM 1200 SPOT
GB
User Manual Rel 1.1
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della DTS .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. DTS non assume alcuna responsabilità sull'uso o sull'applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from DTS.
DTS reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. DTS assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de DTS.
DTS se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de
design, sans préavis, à chacun de ses produits. DTS décline toute responsabilité sur l'utilisation ou sur
l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas.
Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes. Todos los derechos han
sido reservados y este documento no puede ser copiado, fotocopiado o reproducido, total o
parcialmente, sin previa autorizaciónescrita de DTS.
DTS se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter estético,
funcional o de diseño a cada producto suyo. DTS no se asume responsabilidad de ningún tipo sobre la
utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
ARC 1200
XM 1200 SPOT
2
INDEX:
1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 5
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against ultraviolet radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid matter
3- MOUNTING THE LAMPS 6
3.1 Lamp alignment
4- VOLTAGE AND FREQUENCY 7
5- INSTALLATION 7
5.1 Safety chain
5.2 Protection against liquids
5.3 Movement
5.4 Risk of fire
5.5 Forced ventilation
5.6 Ambient temperature
6- MAINS CONNECTION 8
6.1 Protection
7- DMX SIGNAL CONNECTION 8
7.1 DMX Addresses
7.2 Selecting the DMX address
8- DISPLAY FUNCTIONS 11
9- ERROR MESSAGES 14
10- HIDDEN MENU 15
11- OPENING UP THE PROJECTOR HOUSING 17
12- REPLACING GOBOS
13- PERIODIC CLEANING 18
13.1 Lenses and reflectors
13.2 Fans and air passages
13.3 Periodic controls
14- CONTROL MOTORS CARD 19
15- DISPLAY CARD 21
16-PAN & TILT CARD
17- LAMP ON-OFF CONTROL CARD
18-CABLES RESEND CARD
19- DMX PROTOCOL 22
ARC 1200
XM 1200 SPOT
3
ARC 1200
XM 1200 SPOT
4
1- TECHNICAL FEATURES
The XM 1200 Spot is fitted with a Philips MSR 1200/SA discharge lamp
(GY22 lampholder base), with a colour temperature of 5,600 °K and a luminous flux of
96,000 Lumens.
Duration is 750 hours, with replacement recommended before 1000 hours
Other recommended lamps: Osram HTI 1200W/SE PP; GE Lighting CSR1200W SA
The unit incorporates:
Motorized Focus system
13°-31° motorized Zoom with auto-focus
Dimmer (emitted light is controlled by progressive and linear dimming).
Shutter (instantaneous shutter opening/closure)
Strobe: mechanical strobe effect (frequency variable from 0.86 flashes/sec to 6.6
flashes/sec).
Motorized iris
2 gobo wheels (6 indexable 16 bit gobos + open each)
CMY linear colour mixing system
Colour wheel (7 colours + open)
3 rotating prisms
Frost
Electronic or magnetic ballast
Pan: 540° in 5.6 seconds (8 or 16 bit) with auto repositioning system
Tilt: 270° in 4.3 seconds (8 or 16 bit) with auto repositioning system
USITT Standard DMX 512 input
4 -eight digit- LED display with 4 buttons
Power Supply: 190-245 V (50/60 Hz).
Power consumption: 1300 W.
Energy saving function is automatic when the fixture is blacked out.
The XM 1200 Spot is also available with a magnetic ballast, with selectable power supply
(220/230/240 V). Power consumption is 1300 W.
Remote Lamp on/off via DMX
Net weight: 44 Kg (with electronic ballast); 54 Kg (with magnetic ballast).
Packaging Dimensions (LxWxH)
890x600x510mm
Weight: 54 Kg (with electronic ballast)
64 Kg with magnetic ballast
530 mm
610 mm
0
70
mm
410 mm
8
7
0
m
m
500 mm
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
-XM1200 fit a Philips 1200W MSR/SA.
-Other recommended lamps are: Osram HTI 1200W/SE PP; GE Lighting CSR1200W SA
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 m.
-Minimum distance from the closest illuminable surface: 1 m.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.
-The level of technology inherent in the XM1200 requires the assistance of specialised personnel for all
servicing.Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS coveringis damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety chain to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
2.5 Level of protection against the penetration of solid and liquid matter:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 20. XM1200 uses Philips 1200 MSR/SA lamp with GY 22 socket.
The temperature inside the projector can reach 250° C after just 5 minutes, but it can get as high as
350° C. Always check that the lamp is cold before attempting to remove it. In any case, only open the
unit 10 minutes after it has been turned off
ARC 1200
XM 1200 SPOT
5
3- MOUNTING THE LAMPS:
Warning: Switch off the unit before replacing the lamp.
Philips MSR1200/SA
Power 1200W
Luminous flux 96,000 lm
Colour temperature 5.600°K
Lamp base GY 22
Rated life 800 hours
1) Using a screwdriver, remove the 4 screws (A,B, C,D) (photo 1) which fix the lamp holder.
2) Remove the lamp holder assembly (photo2).
Insert the lamp (photo 3).
The lamp used on XM 1200 is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The GY22 lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.
3) Replace the lamp assembly and tighten the screws (A,B,C,D) which were previously removed (photo
4).
3.1 Lamp alignment:
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.
Alignment is carried out using the 3 adjusters X, Y and Z.
During this operation you must have a uniform luminosity all around the projected area.
Osram HTI 1200W/SE PP
Power 1200W
Luminous flux 105,000 lm
Colour temperature 5.400°K
Lamp base GY 22
Rated life 750 hours
ARC 1200
XM 1200 SPOT
6
Photo 2Photo 1 Photo 4Photo 3
GE Lighting CSR1200W SA
Power 1200W
Luminous flux 100,000 lm
Colour temperature 5.800°K
Lamp base GY 22
Rated life 750 hours
Photo 5
4- Voltage and frequency
The Xm1200 E.B.(ELECTRONIC BALLAST) can operate at 190-245 VOLT 50 or 60 Hz.
5- Installation
XM1200 may be either floor or ceiling mounted.
For floor mounting installations, the XM1200 is supplied with four rubber mounting feet on the
base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to
the mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of
the unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as
not to move or shake whilst the XM1200 is moving.
Eight quarter turn fast locks placed on the base of the units,allows by using the two fast lock C
clamps provided in the box, to fix the unit in any position.
.
Safety chain
We recommend the use of a safety cable or chain connected to the XM1200 and to the suspension
truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure
that the iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown
in the picture below.
Protection against liquids
The projector contains electric and electronic components which should under no circumstances
come into contact with oil, water or any other liquid. The proper unit functioning would be
compromised should this occur.
A
ARC 1200
XM 1200 SPOT
7
Movement
The projector has a maximum movement of 540° for Pan and 319° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.
Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum
recommended distance from flammable material is 0.5m.
Minimum distance from the object being illuminated is 2 m.
Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on
both the base and head of the fixture. These should, under no circumstances, be blocked or
obstructed whilst the projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient
temperature should NOT exceed 40°C.
6- MAINS CONNECTION
XM1200 operates at 190-245V at 50 or 60Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is of a suitable rating of 8 amps at 230V.
Strict adherence to regulatory norms is strongly recommended.
Protection
The use of a thermal magnetic circuit breaker is recommended for each Xm1200.
A good earth connection is essential for the correct operation of the projector.
7- DMX signal connection
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
190-245V 50 / 60Hz
ARC 1200
XM 1200 SPOT
8
540°
319°
the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable
and a CANNON XLR 5 or 3 pins connector.
Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR
chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and
connect it to the next projector by connecting the DMX OUT plug on the first projector to the
DMX IN plug of the second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has
occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
The standard configuration of the Xm1200 is with XLR 5 pins connection.
To convert to an XLR 3 pins configuration proceed as follows:
1) Remove the 4 screws fixing the display cover panel to the unit (photo 1).
2) Remove the screws that fix the XLR connectors to the panel (photo 2).
3) Rotate the electronic card by 180° (photo 3).
4) Place the 3 pins XLR connectors in the special holes and close.
For Installations where long distance DMX cable connections are needed,we suggest
to use a DMX terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged in the last unit (DMX out panel connector) of the
DMX line.
Photo 2Photo 1 Photo 3
5
3
4 2
1
1=GND
2=DATA-
3=DATA+
CONTROLLER
S T A N D A R D
D M X 512
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
ARC 1200
XM 1200 SPOT
9
DMX Addresses
Xm1200 can be used in two different modes: 30 or 18 DMX channels.
If you want to use the XM1200 in 18 channels mode, select the 18 CH mode from the MODE menu and
set the following addresses on the mixer:
Projector 1 A001
Projector 2 A019 If you want to select the next projector, just add “18”
Projector 3 A037
….. A….
projector 6 A073
If you want to use the XM1200 in 30 channels mode, select the 30 CH mode from the MODE menu and
set the following addresses:
Projector 1 A001
Projector 2 A031 If you want to select the next projector, just add “30”
Projector 3 A061
….. A….
Projector 6 A151
Changing the DMX address
1) Press the UP-DOWN key until you reach the required DMX number. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
Pushing UP and DOWN keys together,will set the dmx address to channel 001.
ARC 1200
XM 1200 SPOT
10
DMX IN
DMX OUT
DISPLAY
MAINS
190-245V ~ 50-60 Hz
8- DISPLAY FUNCTIONS
ARC 1200
XM 1200 SPOT
11
MENU
ENTER
DOWN
UP
DISPLAY FUNCTIONS
The XM1200 display panel shows all the available functions . Using these functions, it is possible
to change some of the parameters and add some functions. Changing the DTS setting can vary
the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully
follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain thedesired function.
Up-DownMENU ENTERUp-Down
PAN MOVEMENT INVERSION
To reverse Pan movement from left
to right and vice versa on DMX
level variation.
Up-Down
Counterclockwise
Clockwise
Up-DownMENU ENTERUp-Down
TILT MOVEMENT INVERSION
To reverse Tilt movement from
bottom upwards and vice versa on
DMX level variation
Up-Down
Up-Down
MENU
ENTERUp-Down
REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).
Up-Down
Floor
position
Counterclockwise
Clockwise
Suspension
position
Up-DownMENU ENTER
DMX MODE
To select DMX mode : 30-18
channels
30 CHANNELS (Pan & Tilt 16 bit)
18 CHANNELS (Pan & Tilt 16 bit)
Up-Down
Up-Down
Up-DownENTER
Up-DownENTER
DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.
Display OFF
Display
always ON
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
MENU ENTER
TEST MODE
Full test and single function test.
Up-Down
ARC 1200
XM 1200 SPOT
12
Up-Down
LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX
ENTER
FORCED ON
ENTER
FORCED OFF
ENTER
ON / OFF VIA DMX (default)
MENU
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT-FOCUS and ZOOM
ENTER
Up-Down
ENTER
SENS
To set ON-OFF the electronic lamp sensor
ACC
Lamp strikes counter
MENU ENTER
Up-Down
RESET
Al motors reset
MENU ENTER
DEFAULT
To restore default setting
ENTER
Up-Down
Up-Down
RESET ENABLED VIA DMX
RESET DISABLED VIA DMX
RESET ALL MOTORS
MENU ENTER
Fan control
To control the fan speed .
Up-Down
ENTER
Up-Down
(DEFAULT : 30 )
MENU ENTER
Up-Down
ENTER
ENTER
Up-Down
(DEFAULT : 2 )
SPEED control
Pan Tilt Speed control.
ENTER
Up-Down
8- DISPLAY FUNCTIONS
PAN
TILT
DIMMER
SHUTTER
IRIS
GOBO1
GOBO1 ROT.
GOBO1 SHAKE
GOBO2
GOBO2 ROT.
GOBO2 SHAKE
EFFECTS
EFFECTS ROT.
CYAN
MAGENTA
YELLOW
COLOR
FOCUS
ZOOM
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
MENU
SOFTWARE VERSION
Electronic cards software version.
Up-Down
PAN-TILT SOFTWARE (PAN-TILT PCB)
ENTER
Up-Down
.
.
.
DISPLAY SOFTWARE (8 MOT PCB N°2)
HEAD MOT. SOFTWARE (8 MOT PC N°1)
MENU
Up-Down
ENTER
TEMPERATURE
Head electronic thermic sensor
MENU
Up-Down
ENTER
AUTO FOCUS
Automatic focusing
.
Up-Down
AUTOMATIC FOCUS DISABLE
AUTOMATIC FOCUS ENABLE
MENU
Up-Down
ENTER
GOBO ROTATION
GOBO ROTATION during gobo scrolling
Up-Down
GOBO ROTATION DISABLE
GOBO ROTATION ENABLE
.
MENU
Up-Down
ENTER
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
Up-Down
ENTER
.
Up-Down
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
Up-Down
.
ENTER
ENTER
ENTER
Up-Down
ENTER
ENTER
ENTER
Up-Down
.
.
ENTER
PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE
TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE
PAN FREE
REMOVE POWER TO PAN MOTOR
TILT FREE
REMOVE POWER TO TILT MOTOR
MENU ENTER
TIMER
lamp life TIME (reset possible)
and total UNIT LIFE TIME (reset not possible)
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
ARC 1200
XM 1200 SPOT
13
8- DISPLAY FUNCTIONS
ENTER
ENTER
ENTER
ENTER
ARC 1200
XM 1200 SPOT
14
ERROR: ENCODER PAN
ERROR: ENCODER TILT
ERROR: DMX ADDRESS
ERROR: AUTO MODE INPUT
ERROR: EEPROM DATA LOADER
ERROR: RESET CIRCUIT LINE1 (CMY)
ERROR: RESET CIRCUIT LINE2 (GOBO1 , COLOR)
ERROR: RESET CIRCUIT LINE3 (GOBO2 , FOCUS , ZOOM)
ERROR: RESET CIRCUIT LINE4 (EFFECTS , IRIS)
ERROR: MAGENTA POSITION
ERROR: CYAN POSITION
ERROR: YELLOW POSITION
ERROR: GOBO1 POSITION
ERROR: GOBO1 INDEX POSITION
ERROR: COLOUR WHEEL POSITION
ERROR: GOBO2 POSITION
ERROR: GOBO2 INDEX POSITION
ERROR: ZOOM POSITION
ERROR: FOCUS POSITION
ERROR: EFFECT WHEEL POSITION
ERROR: EFFECT INDEX POSITION
ERROR: IRIS POSITION
9- ERROR MESSAGES
ARC 1200
XM 1200 SPOT
15
Up-DownENTER
PAN ALIGNMENT
To align pan position
ES.
ENTER
Up-DownENTER
TILT ALIGNMENT
To align tilt position
ES.
ENTER
Up-Down
Up-Down
ENTER
Up-DownENTERUp-Down
GOBO 1 ALIGNMENT
To align gobo wheel 1
ES.
ENTER
Up-DownENTER
Up-Down
GOBO 1 INDEX ALIGNMENT
To align gobo wheel 1 index
ES.
ENTER
Up-DownENTERUp-Down
GOBO 2 ALIGNMENT
To align gobo wheel 2
ES.
ENTER
Up-DownENTERUp-Down
GOBO 2 INDEX ALIGNMENT
To align gobo wheel 2 index
ES.
ENTER
Up-DownENTERUp-Down
COLOR ALIGNMENT
To align color wheel
ES.
ENTER
Up-DownENTERUp-Down
SHUTTER ALIGNMENT
To align shutter
ES.
ENTER
Up-DownENTERUp-Down
FOCUS ALIGNMENT
To align focus
ES.
ENTER
10- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XM1200 (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
Electronic calibration of the motors.
Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must
repeat all previous calibrations)
Exit from hidden menu.
Up-DownENTER
ZOOM ALIGNMENT
To align zoom
ES.
ENTER
Up-DownENTER
EFFECTS ALIGNMENT
To align effects wheel
ES.
ENTER
Up-Down
Up-Down
ENTER
Up-DownENTERUp-Down
EFFECTS INDEX ALIGNMENT
To align effects wheel index
ES.
ENTER
Up-DownENTER
Up-Down
IRIS ALIGNMENT
To align iris
ES.
ENTER
Up-DownENTERUp-Down
CYAN ALIGNMENT
To align cyan
ES.
ENTER
Up-DownENTERUp-Down
MAGENTA ALIGNMENT
To align magenta
ES.
ENTER
Up-DownENTERUp-Down
YELLOW ALIGNMENT
To align yellow
ES.
ENTER
ARC 1200
XM 1200 SPOT
16
ARC 1200
XM 1200 SPOT
17
11- Opening up the projector housing
It is possible to inspect the inside of the projector by removing the cover as indicated below.
Attention
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the screws which fix the side covers (photo 1 and 2) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 3).
12- Replacing gobos
XM1200 uses a mechanical system which allows the fixture's gobos to be removed without the use
of special tools. Replacement gobos should be made of either heat resistant glass or metal.
An ever-increasing range of gobos is available from your DTS sales network.
Gobo dimensions are as follows:
ø external = 37 mm
ø of image with defined edge = 32 mm
thickness = from 0.2 to 3.5 mm (see catalogue)
Replacing gobos on the rotating gobo wheels
When replacing gobos, ensure that the projector is switched off.
1) Open the projector housing as described above.
2) Remove the gobo holder to allow easier access to the gobo(photo 1-2).
3) Release the gobo retaining spring and carefully remove the gobo (photo 3).
4) Reverse the procedure to install a replacement gobo.
Photo 1 (gobo wheel 1)
Photo 2 (gobo wheel 2)
Photo 3
Photo 1
Photo 2 Photo 3
13 Periodic cleaning
Lenses and reflectors
Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend of course, on the conditions in which the projector is operating. Suitable instruments
for performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.
Periodic controls
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.
Mechanical parts
Periodically check all mechanical parts gears, guides, belts, etc.for wear and tear, replacing them
if necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors,
refastening if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the Xm1200.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.
Attention
Disconnect mains power prior to removing the projector housing.
ARC 1200
XM 1200 SPOT
18
Gobo1 (line 2)
(BLACK)
Gobo1 Rot.
(DARK GREEN)
Strobe
Yellow (line 1)
(PINK)
Colours (line 2)
(LIGHT BLUE)
Cyan (Line 1)
(GOLD)
Magnetic
Sensors
Fans
14- CONTROL MOTORS CAR
+
-
(Line 1)
Line 1 Brown
Line 2 Orange
Magenta (line 1)
(BLUE)
GND
ORANGE
BROWN
VCC
J5 FROM
J10 PAN & TILT
(YELLOW)
Display
30 VDC
J3 FROM
J8 PAN & TILT
TEMP
GND
LIGHT
GND
Free
Electronic
sensors
lamp&temp
J9 FROM
J2 TCN0108
ARC 1200
XM 1200 SPOT
19
8 MOTORS PCB “1
Gobo2 (line 1)
(BLACK)
Gobo2 Rot.
(DARK GREEN)
Free
Effects (line 2)
(PINK)
Iris (line 2)
(GREY)
Zoom (line 1)
(LIGHT BLUE)
Effects Rot. (Line 2)
(GOLD)
Magnetic
Sensors
J3 FROM
J8 PAN & TILT
FANS
30 VDC
+
-
(Line 1)
Line 1 Brown
Line 2 Orange
Focus (line 1)
(BLUE)
GND
ORANGE
BROWN
VCC
J5 FROM
J10 PAN & TILT
ARC 1200
XM 1200 SPOT
20
8 MOTORS PCB “2”
14- CONTROL MOTORS CAR
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

DTS XM 1200 SPOT Manuale utente

Tipo
Manuale utente

in altre lingue