DTS XR2000 SPOT CMY Manuale utente

GB

Made in Italy

XR2000 SPOT CMY

User’s Manual Rel 1.6

D.T.S. Illuminazione srl - ITALY

http://www.dts-lighting.it

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

D.T.S

D.T.S.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S.

2

XR2000 SPOT CMY

3

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 7

6- IMPORTANT SAFETY INFORMATION 8

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects

7- MOUNTING THE LAMP 9

7.1 Lamp alignment

8- VOLTAGE AND FREQUENCY 10

9- INSTALLATION 10

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 11

10.1 Protection

11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 13

13- DISPLAY FUNCTIONS 14

14- ERROR MESSAGES 17

15- HIDDEN MENU 18

15.1 Calibration mode 19

16- PAN & TILT SPEED 20

17- FANS SPEED

18- OPENING THE PROJECTOR HOUSING 21

19- REPLACING GOBOS

20- PERIODIC CLEANING 22

20.1 Lenses and reflectors

20.2 Fans and air passages

21- PERIODIC CONTROLS

22- DMX PROTOCOL 23

23- 8 MOTORS CONTROL CARD 38

24- 8 MOTORS SLAVE CONTROL CARD 39

25- PAN & TILT CARD 40

26- CABLES RESEND CARD

27- DISPLAY CARD

28- LAMP ON-OFF CONTROL CARD

29- ROTATING GOBO WHEEL 41

30- FIXED GOBO WHEEL 42

31- COLOUR WHEEL 1 43

XR2000 SPOT CMY

1- SYMBOLS

Graphic symbols used on this manual

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information

regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or experienced

person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON

INFLAMMABLE SURFACES”

2M

THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO

BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT

4

F

THIS SYMBOL MEANS “RADIATION FROM THIS LAMP

CAN CAUSE DAMAGE TO EYES AND SKIN”

!

UV

XR2000 SPOT CMY

4- TECHNICAL FEATURES

Lamp

Lamp: Philips MSR Gold 700/2 Fastfit

Automatic switching ON of lamp in case of accidental switching OFF.

Lamp ON/OFF via DMX; Reset via DMX.

Optical group

Focus

Motorized focus

Iris

Motorized iris (16 bit)

Zoom

Motorized zoom (8°- 30°)

The XR2000 SPOT CMY is one of the most powerful moving heads in the 700W range.

The XR2000 SPOT CMY in fact delivers a massive 64.300 Lux at 5 m (8° beam angle), thanks to its

improved optical group and dichroic glass reflector, combined with a Philips MSR Gold 700/2 Fastfit lamp

(50.000 Lumens).

The XR2000 SPOT CMY is particularly suitable for all professional applications, both mobile (concerts,

shows, tours, special events) and fixed (clubs and other venues), requiring a light with extremely high

luminous output and versatility of functions.

The XR2000 SPOT CMY is also the ideal light for a vast range of applications in which quiet operation is

a priority, thanks to its silent ventilation system and silent pan/tilt operation.

The XR2000 SPOT CMY incorporates motorized focus; motorized iris; linear zoom (8°- 30°); a

sophisticated CMY colour synthesis system with 3 palettes for linear insertion, plus a colour wheel (7

colours + open); 2 gobo wheels: one customizable rotating gobo wheel (7 gobos) and one customizable

fixed gobo wheel (8 gobos); frost filter (soft edge); 3-facet rotating prism; animation wheel rotating in

both directions.

The 16 bit Pan/Tilt mechanism features an exclusive Super Speed function, and a locking system with

recessed buttons. Access to every feature of the internal menu is simple and direct, thanks to the new

user interface featuring a LCD backlit graphic display (128 x 64).

XR2000 SPOT CMY

(Cod. 03.MS008.EB.L)

• Electronic ballast 90-245V 50/60 Hz • Black finish

Also available with white finish (RAL 9003) on demand

64.300 Lux at 5 m (8° beam angle)

Dichroic glass reflector

5

XR2000 SPOT CMY

4- TECHNICAL FEATURES

Dimmer / shutter / strobo

Linear dimmer

Shutter

Strobe from 0,85 flash/sec to 6,75 flash/sec

Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Colours

Gobos

2 gobo wheels: 1 rotating (7 indexable 16 bit gobos + open) and 1 fixed (8 gobos + open)

Extractable gobo holders for both wheels

Gobo change with synchronized blackout

Gobo scrolling; Gobo shake

Effects

Pan / Tilt

30 DMX channels (Default)

Internal operating system updatable via DMX

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

POWERCONN connector by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz)

Power consumption: 820 W

Standard accessories

2 x “C” GQuick clamps with “fastlock” connection

Thermal

Operating ambient temperature: -10° / 40°

Weight

CMY colour synthesis system + colour wheel (7 colours + open) with linear selection for perfect 2-colour

beams

Colour change with blackout sync; rainbow effect

Indexable prism rotating in both directions (3-facet)

Frost filter (soft edge)

Animation wheel rotating in both directions

Pan 540° (3,9 sec.); Tilt 270° (2,6 sec.); 16-bit resolution

Super Speed function; extremely smooth and precise movements even at the highest speeds

Pan / Tilt locking system with recessed buttons

Automatic Pan/Tilt repositioning in case of knocks

Interface

LCD backlit graphic display (128x64)

Power saving mode (the lamp dims to 50% six seconds after shutter closure)

44,5 Kg

6

XR2000 SPOT CMY

4- TECHNICAL FEATURES

Dimensions

5- ACCESSORIES

As standard

•1 x MSR Gold 700/2 Fastfit lamp

•1 x POWERCONN male cable connector (cod. 0520P014)

•1 x XLR 5 Pins male cable connector (cod. 0508B028)

•1 x XLR 5 Pins female cable connector (cod. 0508B027)

•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• User’s manual

Optional (on request)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

Unit Dimensions (LxWxH)

568x510x826mm

Weight: 44,5 Kg

Packaging Dimensions (LxWxH)

670 x 550 x 730 mm

Weight: 49,5 Kg

7

XR2000 SPOT CMY

568mm

7 °2

0

m

826

m

459mm

510mm

636

m

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

MSR Gold 700 Fastfit lamp

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1.5 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if

there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves

touching the inside of the moving head, including lamp replacement.

-The level of technology inherent in the XR2000 SPOT CMY requires the assistance of specialised

personnel for all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective

shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of

supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main

fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at

least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should

not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the penetration of

solid and liquid objects is IP 20.

For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:

XR2000 SPOT CMY uses a PHILIPS /2

• Raincover for XR2000 base (top) (cod. 03.MA009)

• Raincover for XR2000 base (bottom) (cod. 03.MA010)

2M

8

F

!

UV

XR2000 SPOT CMY

7- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

2) Insert the lamp (photo2).

3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4).

The lamp used on XR2000 SPOT CMY is made in quartz glass and should be handled with care. Always

follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue

provided in the lamp’s packaging. The lamp socket is not symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat

the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which were previously removed.

WARNING: Never look directly at the lamp when it’s lit.

Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.

7.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic

filters and other components inside the unit. The lamp alignment is also essential to obtain the

maximum unifirmity and luminous performance by the projection.

3 adjusters X, Y and

Z (photo 5)

you will have an evenly projected light beam, with no shadows or

zones wich are brighter than others.

Philips MSR Gold 700/2 Fastfit

Power 700W

Luminous flux 50,000 lm

Colour temperature 7.500°K

Lampbase PGJX50

Rated life 750 hours

PGJX50

1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface

no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto

the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the

until you achieve a uniform flat field.

When the lamp is correctly optimized,

Photo 2Photo 1 Photo 4Photo 3

Photo 5

9

Lamp

Alignment

UV

XR2000 SPOT CMY

Normal Hot Spot

8- VOLTAGE AND FREQUENCY

The XR2000 SPOT CMY with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

XR2000 SPOT CMY may be either floor or ceiling mounted.

For floor mounting installations, the XR2000 SPOT CMY is supplied with four rubber mounting feet on

the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the

mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the

unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to

move or shake whilst the XR2000 SPOT CMY is moving.

Eight 1/4 turn Fast Locks connections placed in the base of the unit allow to fix the XR2000 SPOT CMY in

any position, by using the two Fast Lock “C” clamps provided in the box.

.

9.1- Safety cable

We recommend the use of a safety cable connected to the XR2000 SPOT CMY and to the suspension

truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the

iron cable can bear the weight of the entire unit.

You may attach the safety cable to the two holes (A) located on the base of the fixture, as shown in the

picture below.

9.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come

into contact with oil, water or any other liquid. The proper unit functioning would be compromised

should this occur.

A

!

240 mm

107 mm

10

XR2000 SPOT CMY

9.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any

obstructions in the path of the projector's movement.

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended

distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 2 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the

base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the

projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature

should NOT exceed 40°C.

10- MAINS CONNECTION

XR2000 SPOT CMY with electronic ballast operate at 90-260 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply,

ensure that the model in your possession correctly matches

the mains supply available. For connection purposes,

ensure that your plug is capable of supporting 8 amps at 230V,

Or 16 amps at 100-120 V

Strict adherence to regulatory norms is strongly recommended.

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR2000 SPOT CMY.

A good earth connection is essential for the correct operation of the projector.

540°

270°

11

2M

F

!

WARNING

Do not place any object in the path

of the projector’s movement

!

XR2000 SPOT CMY

Electronic ballast

90-260V 50 / 60Hz

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the

projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR

5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable

ground to the XLR chassy

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it

to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the

second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

12

XR2000 SPOT CMY

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N DA R D

D M X 5 1 2

11.1-DMX Addresses

XR2000 SPOT CMY can be controlled with 30 (default) or 22 DMX channels.

If you want to use the unit in 30 channels mode (default), set the following addresses on the mixer:

Projector 1 A001

Projector 2 A031 If you want to select the next projector, just add “30”

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will

start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a

faster selection.

Projector 3 A061

….. A….

projector 6 A151

12 FIRMWARE UPDATING

Warning:

This procedure require a base knolewge of computer applications and Windows

Hyperterminal program.

To update the software version of the XR2000 SPOT CMY you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface .

(The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal program.

It will be possible to download the software from the reserved area of D.T.S. web site:

www.dts-lighting.it.

Please refer to an authorised DTS service centre.

13

!

XR2000 SPOT CMY

14

XR2000 SPOT CMY

MAINS

Electronic ballast

90-260V 50 / 60Hz

DMX IN

DMX OUT

DISPLAY

MENU

ENTER

DOWN

UP

13- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The XR2000 SPOT CMY display panel shows all the available functions . Using these functions, it is

possible to change some of the parameters and add some functions. Changing the DTS setting

can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.

Carefully follow the instructions below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

DMX IN

DMX OUT

FUSE 16A T 5X20

PAN DIRECTION

NORMAL

MENU ENTER DOWN UP

Pan Direction

Up-Down

Up-DownENTER

PAN DIRECTION

This menu allows to set the Pan

movement.

Normal or Reversed

Pan movement Normal or Reversed

Default = Normal

ENTER

Menu

TILT DIRECTION

NORMAL

MENU ENTER DOWN UP

Tilt Direction

Up-Down

Up-DownENTER

TILT DIRECTION

This menu allows to set the Pan

movement.

Normal or Reversed

Tilt movement Normal or Reversed

Default = Normal

ENTER

Menu

PAN TILT SPEED

4

MENU ENTER DOWN UP

Pan Tilt Speed

Up-Down

Up-DownENTER

PAN TILT SPEED

Pan Tilt Speed control (1-4)

Pan Tilt Speed control

Default = 4

ENTER

Menu

15

XR2000 SPOT CMY

13- DISPLAY FUNCTIONS

MENU ENTER DOWN UP

Display

Up-Down

Up-DownENTER

Display Flip

ON THE GROUND (Default)

SUSPENDED

ENTER

Menu

DISPLAY FLIP / STAND BY / CONTRAST

Display Flip:

Reverses display's reading depending on the

mounting position

(On the ground or suspended).

Display Standby:

To turn off the display (after 5 seconds)

Or leave it always on.

Display Contrast:

Display contrast regulation (1-16)

FLIP

ON THE GROUND

DISPLAY

MENU ENTER DOWN UP

FLIP

STANDBY

OFF

DISPLAY

MENU ENTER DOWN UP

FLIP

CONTRAST

8

DISPLAY

Display Standby

OFF = Display Standby disabled

(Default)

ON = Display goes OFF after 5

seconds

ENTER

Display Contrast

1-16 (Default = 8)

DMX MODE

30 channels

MENU ENTER DOWN UP

DMX Mode

Up-Down

Up-DownENTER

DMX mode

30 channels (Default)

22 channels

ENTER

Menu

DMX MODE

To select DMX mode :

30 channels or 22 channels

ENTER

BY DMX = ON / OFF via DMX (default)

ALWAYS ON = Forced ON

ALWAYS OFF = Forced OFF

RESET COUNTER = Lamp life time

reset

LAMP ADJUST =

To adjust the lamp

with no mixer connected.

It’s possible to set the parameters for

PAN-TILT and ZOOM

FLIP

LAMP

FLIP

LAMP

ADJUST

UP

DOWN

ENTER

MENU

Up-DownENTER

LAMP

Lamp always ON, always OFF,

lamp ON-OFF selectable via DMX

And lamp life time reset

ADJUST

To adjust the lamp with no mixer

connected.

It’s possible to set the parameters for

PAN-TILT and ZOOM

Lamp

Up-Down

Menu

BY DMX

MENU ENTER DOWN UP

ENABLED = Reset via DMX enabled

(Default)

DISABLED = Reset via DMX disabled

NOW = Unit motors reset

RESET

Reset via DMX ENABLED / DISABLED

and unit reset

ENABLED

BY DMX

RESET

Reset

Up-Down

Up-DownENTER

ENTER

Menu

16

XR2000 SPOT CMY

13- DISPLAY FUNCTIONS

CMY BLACKOUT

ON

MENU ENTER DOWN UP

CMY Blackout

Up-Down

Up-DownENTER

ON = Blackout enabled (Default)

OFF = Blackout disabled

ENTER

Menu

CMY BLACKOUT

CMY filters blades inserted at 100% if the dimmer

remain closed for more than 5 seconds.

By activating this function, it will be possible to

reduce substantially any visible light reflection

coming out from the front lens when dimmer is

closed.

SYSTEM INFO

LAMP LIFE:0000H STRIKE:001

UNIT LIFE: 0010H

8M R.20

PT R.19

MODEL: XR2000 BEAM

MENU ENTER DOWN UP

System info

Up-Down

Up-DownENTER

SYSTEM INFO

Lamp life time, lamp strikes, unit life

time, 8 motors card software

version, Pan&Tilt card software

version and unit model

ENTER

Menu

SYSTEM INFO

Lamp life time, lamp strikes, unit life time, 8

motors card software version, Pan&Tilt card

software version and unit model

Reserved

Up-Down

Up-DownENTER

ENTER

Menu

RESERVED

Pan lock-Tilt lock

Pan free-Tilt free

System Reboot

(Code = 100)

RESERVED

000

MENU ENTER DOWN UP

ENTER CODE

FAN SPEED

5

MENU ENTER DOWN UP

Fan Speed

Up-Down

Up-DownENTER

Fan speed control

1-5 (Default = 5)

ENTER

Menu

FAN SPEED

Fan Speed control

GOBO ROTATION

OFF

MENU ENTER DOWN UP

Gobo Rotation

Up-Down

Up-DownENTER

ON

OFF = (Default)

ENTER

Menu

GOBO ROTATION

Gobo rotation control the Rotating speed of gobo

During gobo scrolling

AUTO FOCUS

OFF

MENU ENTER DOWN UP

Auto Focus

Up-Down

Up-DownENTER

ON

OFF = (Default)

ENTER

Menu

AUTO FUCOS

Automatic focusing

Pan Lock = Lock the Pan to the

desired value

Tilt Lock = Lock the Tilt to the

desired value

Pan Free = Remove power to Pan

motor

Tilt Free = Remove power to Tilt

motor

System Reboot = Unit Reboot

without needing of turning OFF the

unit

PAN LOCK

NO

MENU ENTER DOWN UP

17

XR2000 SPOT CMY

Default

Up-Down

Up-DownENTER

Default

To restore main settings

ENTER

Menu

DEFAULT

To restore main settings

DEFAULT

SURE?

MENU ENTER DOWN UP

RESTORE MAIN SETTINGS

DEFAULT

RESTORE MAIN SETTINGS

MENU ENTER DOWN UP

PRESS ENTER TO CONFORM

PRESS MENU TO CANCEL

14- ERROR MESSAGES

13- DISPLAY FUNCTIONS

MENU ENTER DOWN UP

ERROR

COLOUR WHEEL

MENU ENTER DOWN UP

ERROR

CYAN

MENU ENTER DOWN UP

ERROR

MAGENTA

MENU ENTER DOWN UP

ERROR

YELLOW

MENU ENTER DOWN UP

ERROR

PAN

MENU ENTER DOWN UP

ERROR

TILT

MENU ENTER DOWN UP

ERROR

INTERNAL BUS

MENU ENTER DOWN UP

ERROR

DMX ADDRESS

COLOUR WHEEL

POSITION ERROR

CYAN POSITION ERROR MAGENTA POSITION

ERROR

YELLOW POSITION

ERROR

PAN REPOSITIONING

ENCODER ERROR

TILT REPOSITIONING

ENCODER ERROR

COMMUNICATION

PROBLEM BETWEEN 8

MOTORS CARD AND

PAN&TILT CARD

DMX ADDRESS

ERROR

MENU ENTER DOWN UP

ERROR

GOBO

MENU ENTER DOWN UP

ERROR

GOBO INDEX

MENU ENTER DOWN UP

ERROR

FIXED GOBO

MENU ENTER DOWN UP

ERROR

ANIMATION

GOBO WHEEL ERROR GOBO POSITION

ERROR

FIXED GOBO WHEEL

ERROR

ANIMATION WHEEL

ERROR

18

XR2000 SPOT CMY

15- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the XR2000 SPOT CMY (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

ELECTRONIC

CALIBRATION OF THE

MOTORS

RESET EEPROM.

RESET ALL SETTINGS

TO 128 VALUE

EXIT FROM HIDDEN

MENU

CALIBRATION

PAN

MENU ENTER DOWN UP

MOTORS ALIGNMENT

134

DEFAULT CAL

MENU ENTER DOWN UP

SET ALL MOTORS AT 128

EXIT TO MAIN

MENU ENTER DOWN UP

FAN SPEED WHEN

DIMMER CLOSED

FANS SPEED

MENU ENTER DOWN UP

ONLY AT MIN LAMP POWER

3

LAMP POWER WHEN

DIMMER CLOSED

MIN LAMP POW.

MENU ENTER DOWN UP

1=65% 100=100%

10

MENU ENTER DOWN UP

ERROR

IRIS

MENU ENTER DOWN UP

ERROR

EFFECT

MENU ENTER DOWN UP

ERROR

FOCUS

MENU ENTER DOWN UP

ERROR

ZOOM

IRIS ERROR

EFFECT WHEEL ERROR

FOCUS ERROR

ZOOM ERROR

MENU ENTER DOWN UP

ERROR

DIFFUSER

DIFFUSER ERROR

19

CYAN PATH ALIGNMENT

Cyan excursion setting

MAGENTA ZERO ALIGNMENT

Magenta zero position setting

YELLOW ZERO ALIGNMENT

Yellow zero position setting

15.1 Calibration

CALIBRATION

CYAN PATH

MENU ENTER DOWN UP

MOTORS ALIGNMENT

134

CALIBRATION

MAGENTA ZERO

MENU ENTER DOWN UP

MOTORS ALIGNMENT

167

CALIBRATION

YELLOW ZERO

MENU ENTER DOWN UP

MOTORS ALIGNMENT

141

MAGENTA PATH ALIGNMENT

Magenta excursion setting

CALIBRATION

MAGENTA PATH

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

YELLOW PATH ALIGNMENT

Yellow excursion setting

CALIBRATION

MENU ENTER DOWN UP

MOTORS ALIGNMENT

121

YELLOW PATH

PAN ALIGNMENT

To align Pan position

TILT ALIGNMENT

To align Tilt position

SHUTTER ALIGNMENT

To align Shutter blades

GOBO WHEEL INDEX ALIGNMENT

To align Gobo wheel Index

CYAN ZERO ALIGNMENT

Cyan zero position setting

IRIS ALIGNMENT

To align IRIS

CALIBRATION

PAN

MENU ENTER DOWN UP

MOTORS ALIGNMENT

134

CALIBRATION

TILT

MENU ENTER DOWN UP

MOTORS ALIGNMENT

167

CALIBRATION

SHUTTER

MENU ENTER DOWN UP

MOTORS ALIGNMENT

145

CALIBRATION

GOBO INDEX

MENU ENTER DOWN UP

MOTORS ALIGNMENT

141

CALIBRATION

IRIS

MENU ENTER DOWN UP

MOTORS ALIGNMENT

85

CALIBRATION

CYAN ZERO

MENU ENTER DOWN UP

MOTORS ALIGNMENT

162

GOBO WHEEL ALIGNMENT

To align Gobo wheel

CALIBRATION

GOBO

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

COLOUR WHEEL ALIGNMENT

To align Colour wheel

CALIBRATION

COLOUR WHEEL

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

G O B O F I X E D W H E E L

ALIGNMENT

To align Gobo wheel

CALIBRATION

FIXED GOBO

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

ANIMATION WHELL ALIGNMENT

To align ANIMATION WHEEL

CALIBRATION

ANIMATION

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

XR2000 SPOT CMY

20

Calibration mode

EFFECTS ALIGNMENT

To align EFFECTS

CALIBRATION

EFFECTS

MENU ENTER DOWN UP

MOTORS ALIGNMENT

85

DIFFUSER ALIGNMENT

To align DIFFUSER

CALIBRATION

DIFFUSER

MENU ENTER DOWN UP

MOTORS ALIGNMENT

85

FOCUS ALIGNMENT

To alignFOCUS

CALIBRATION

FOCUS

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

ZOOM ALIGNMENT

To align ZOOM

CALIBRATION

ZOOM

MENU ENTER DOWN UP

MOTORS ALIGNMENT

151

16- PAN & TILT SPEED (default: 4)

17- FAN SPEED ( default: 5)

You can set the PAN and TILT motors at high speed on your XR2000 SPOT CMY.

Press menu until you see PAN TILT SPEED.

Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be

less than 35° C.

XR2000 SPOT CMY

La pagina sta caricando ...

DTS XR2000 SPOT CMY Manuale utente

DTS XR2000 SPOT CMY Manuale utente

in altre lingue

Documenti correlati

Altri documenti