DTS NICK NRG1200 CT Manuale utente

D.T.S. Illuminazione srl

[email protected] http://www.dts-lighting.it

Via Fagnano Selve 10/12/14

47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111

Made in Italy

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull‟uso o sull‟applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- TECHNICAL SPECIFICATIONS 7

6- ACCESSORIES 7

7- IMPORTANT SAFETY INFORMATION 8

7.1 Fire prevention

7.2 Prevention of electric shock

7.3 Safety

7.4 Level of protection against the penetration of solid and liquid objects

8- VOLTAGE AND FREQUENCY 9

9- INSTALLATION 9

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 11

10.1 Protection

11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 13

13- DISPLAY FUNCTIONS 14

14- PERIODIC CLEANING 23

15- PERIODIC CONTROLS 23

16- DMX PROTOCOL 24

4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK

RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE

UNIT ON INFLAMMABLE SURFACES”

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE DEVICE

AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

F

!

0,5M

5

4- TECHNICAL FEATURES

Overview

NICK NRG 1201 is the most efficient LED moving head wash light ever produced and,

thanks to its specifically developed optical group, fears no competition.

The exceptional brightness/consumption ratio makes NICK NRG 1201 a truly “green”

fixture.

NICK NRG‟s new-generation optical group is an exclusive D.T.S. feature.

NICK NRG 1201 is equipped with 30 high-power full-colour LEDs (RGBW).

NICK NRG 1201 features 8°- 50° motorized zoom with a high efficiency optical system

enabling it to be used as a PC Beam or a very wide Wash and ultra-fast silent Pan/Tilt.

NICK NRG 1201 (Cod. 03.LDR006.FFP; Cod. 03.LDR006.FWFP), is also equipped

with the “FPR” system (patent pending), which enables limitless pan rotation in both

directions, with no need for inversion.

Applications

NICK NRG 1201 is suitable for top professional applications, such as tours and special

events.

NICK NRG 1201 is also available as NICK NRG 1201 CT (30 Full White LEDs,

2700°K-6500°K).

Product codes

03.LDR006.F NICK NRG 1201 FULLCOLOR BLACK ZOOM

03.LDR006.FFP NICK NRG 1201 FULLCOLOR FPR BLACK ZOOM

03.LDR006.FW NICK NRG 1201 CT FULLWHITE BLACK ZOOM

03.LDR006.FWFP NICK NRG 1201 CT FULLWHITE FPR BLACK ZOOM

LED Technology

* 30 Full Colour LEDs (RGBW)

Optical group

* 8°- 50° linear motorized zoom with high-efficiency optical system

* Uniform projection on surfaces, from very wide Wash to PC Beam

Colour generation

* 16 million colours

* Wide palette of pure uniform whites with variable

linear colour temperature (2700°K – 8000°K)

Interface / Control / Programming

* Multi-function OLED graphic colour display + 4 soft keys:

control / management / monitoring of the main parameters

* Controlled via DMX 512 and RDM standard digital communication protocols

* Wireless ready

* Ethernet ready

* Internal operating system updatable via D.T.S. RED BOX interface via “D.T.S.

firmware upgrade utility” program on windows based PC

6

DMX

20 DMX channels

Pan & Tilt

NICK NRG 1201 FPR (Cod. 03.LDR006.FFP; Cod. 03.LDR006.FWFP)

* „FPR‟: limitless pan rotation, in either direction, never having to reverse motion

Tilt 270° (1,2 sec.)

NICK NRG 1201 (Cod. 03.LDR006.F; Cod. 03.LDR006.FW)

* Ultra-fast movement: Pan 540° (2 sec.); Tilt 270° (1,2 sec.)

* 16-bit movement resolution

* 4 Selectable speed ranges

Power supply

* Electronic full-range AC 90-260 V 50 / 60 Hz

* Power consumption: 90 V – 3,7 A – 340 W ; 120 V – 2,83 A – 340 W ;

230 V – 1,47 A - 340 W ; 260 V – 1,3 A – 340 W

Connectors

* DMX: 4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik;

* Power supply: POWERCONN In/Out connectors by Neutrik.

Operating ambient temperature

-10° / 40°

Weight

10,5 Kg

International certifications

Certification CE; LED Class: Class 2 LED product

7

5- TECHNICAL SPECIFICATIONS

Dimensions

Packaging Dimensions (LxWxH)

530 x 430 x 414 mm

Weight: 13 Kg

Unit Dimensions (LxWxH)

369x218x497 mm

Weight: 10,5 Kg

6- ACCESSORIES

As standard

• 1 x POWERCONN male cable connector (cod. 0520P014)

• 1 x XLR 5 Pins male cable connector (cod. 0508B028)

• 1 x XLR 5 Pins female cable connector (cod. 0508B027)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (cod. 0521A014)

• User‟s manual

Optional (on request)

Flight case

• Professional Flight case for 4 units; compartment for accessories, swivel wheels,

cover with hinges with-stay, dishes on cover for piling, 8 handles (2 eachside) (cod.

0521C051.1)

Wireless DMX receiver retrofit

• Wireless DMX Receiver Card with INDOOR IP20 omni. 2dBi antenna included

(cod.03.LA.126)

Clamps / safety wires

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod.

0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn 1 couple (2 pieces) (Cod.

02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod.

0521A010)

218 mm

369 mm

4

9

7

m

4

1

3

m

306 mm

195 mm

8

7- IMPORTANT SAFETY INFORMATION

7.1 Fire prevention:

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 0,5 MT.

-Replace any blown or damaged fuses only with those of identical value.

Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

7.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any

function which involves touching the inside of the moving head.

-The level of technology inherent in the NICK NRG 1201 requires the assistance of

specialised personnel for all servicing.

Please refer to an authorised D.T.S. service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

7.3 Safety:

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the

failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle

the unit until at least 10 minutes have elapsed since the projector was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

7.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the

penetration of solid and liquid objects is IP 20.

F

!

0,5M

9

8- VOLTAGE AND FREQUENCY

The NICK NRG 1201 can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

NICK NRG 1201 may be either floor or ceiling mounted.

For floor mounting installations, the NICK NRG 1201 is supplied with four rubber

mounting feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix

the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hung it. The structure should also be

sufficiently rigid so as not to move or shake whilst the NICK NRG 1201 is moving.

Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the

NICK NRG 1201 by using the Fast Lock “C” clamps provided in the box.

9.1- Safety cable

We recommend the use of a safety cable or chain connected to the NICK NRG 1201

and to the suspension truss in order to avoid the fixture accidentally falling should the

main fixing point fail.

Make sure that the iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain/cord to the attachment point (A) located on the base

of the fixture, as shown in the picture below.

!

SAFETY CHAIN/CORD

ATTACHMENT POINT

A

10

270°

9.2 Protection against liquids

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

9.3- Movement

NICK NRG 1201 FPR (Cod. 03.LDR006.FFP; Cod. 03.LDR006.FWFP)

Unlimited Pan rotation; Tilt 270° (1,2 sec.)

NICK NRG 1201 (Cod. 03.LDR006.F; Cod. 03.LDR006.FW)

Ultra-fast movement: Pan 540° (2,0 sec.); Tilt 270° (1,2 sec.)

DO NOT place any obstructions in the path of the projector's movement.

WARNING

Do not place any object in the

path of the projector‟s

movement

Free Pan Rotation („FPR‟) No „FPR‟

(Cod. 03.LDR006.FFP) (Cod. 03.LDR006.F)

(Cod. 03.LDR006.FWFP) (Cod. 03.LDR006.FW)

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

The minimum recommended distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 0,5 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans

located on the head of the fixture.

These should, under no circumstances, be blocked or obstructed whilst the projector is

in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should NOT exceed 40°C.

F

!

0,5M

540°

270°

11

10- MAINS CONNECTION

NICK NRG 1201 operate at 90-260 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 1,5 amps

at 230V, or 3 amps at 90 V.

Strict adherence to regulatory norms is strongly recommended.

MAINS AC OUTPUT 90 – 260 V 50 / 60 Hz (16A Max)

MAX 10 NICK NRG 1201 UNITS @ 230V

MAX 5 NICK NRG 1201 UNITS @ 120V

Cod. 03.LDR006.F

Cod. 03.LDR006.FW

Cod. 03.LDR006.FFP

Cod. 03.LDR006.FWFP

MAINS AC INPUT 90 – 260 V 50 / 60 Hz

Wireless DMX Receiver Retrofit (Cod. 03.LA.126)

FUSE 5A T 5X20

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each NICK NRG

1201.

!

12

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal.

Connection between the mixer and the projector or between projectors must be carried

out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors

has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest

to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N D A R D

D M X 5 1 2

DMX OUT

DMX OUT DMX IN

DMX IN

DMX IN DMX OUT

13

11.1-DMX Addresses

NICK NRG 1201 can be controlled with 20 DMX channels.

In order to use the unit in 20 channels, set the following addresses on the mixer:

Projector 1 A001

Projector 2 A021 If you want to select the next projector, just add “20”

Projector 3 A041

….. A….

projector 6 A101

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly

and you get a faster selection.

12- FIRMWARE UPDATING

Warning:

This procedure require a base knowledge of computer applications and Windows

Hyperterminal program. Please refer to an authorised D.T.S. service centre.

To update the software version of the NICK NRG 1201 you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface.

D.T.S. Firmware upgrade utility program.

(The driver and the installation procedure are available in our web site

www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using D.T.S. Firmware upgrade

utility program.

!

14

13- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The NICK NRG 1201 display panel shows all the available functions . Using these

functions, it is possible to change some of the parameters and add some functions.

Changing the D.T.S. setting can vary the functions of the unit so that it does not

respond to the DMX 512 used to control it. Carefully follow the instructions below

before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

MENU

ENTER

DOWN

UP

DISPLAY

MAINS AC INPUT

90-260V 50 / 60Hz

MAINS AC OUTPUT

90-260V 50 / 60 Hz

(16A Max)

DMX OUT

DMX IN

DMX OUT

DMX IN

03.LDR006.F

03.LDR006.FW

03.LDR006.FFP

03.LDR006.FWFP

2dBi IP20 omnid.

antenna

DMX

IN

DMX

OUT

WIRELESS DMX

RECEIVER

RETROFIT

03.LA.126

15

13- DISPLAY FUNCTIONS

Software version 1.04

Display

DISPLAY POSITION / STAND BY

Display Position:

Reverses display's reading depending on

the mounting position

(on the ground or suspended).

Display Standby:

To turn off the display (after 5 seconds)

or leave it always on.

DMX Set

DMX MODE / MACRO

DMX Mode

20 channels

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

AA

DISPLAY

MENU ENTER DOWN

UP

OFF

DISPLAY

POSITION

STANDBY

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

20 ch With FAR

DMX SET

DMX MODE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

STD

DMX SET

MACRO

STD = Standard mode enabled

(Default)

EXT = Extended; enable rainbow

effects on Macro channel

(DMX ch 16)

MACRO

Macro Mode:

STD = Standard (Default)

EXT = Extended; enable rainbow

effects on Macro channel (DMX ch 16)

Display Position

ON THE GROUND (Default)

SUSPENDED

Display Standby

OFF = Display Standby

disabled (Default)

ON = Display goes OFF

after 5 seconds

DMX Mode

20 channels

16

13- DISPLAY FUNCTIONS

LED

RGBA MINIMUM VALUES

This menu allow to select the

minimum levels for Red, Green,

Blue and Amber/White

RGBA MAXIMUM VALUES

This menu allow to select the

maximum levels for Red, Green,

Blue and Amber/White

These settings have priority

on Master Dimmer (DMX channel 9)

SMOOTH VALUE

This menu allow to select the value

of the delay (in milliseconds) for

RGBA and Dimmer channels

reaction to DMX or Program

variation.

4 = 25 ms delay (Fast response)

20 = 250 ms delay (Slow response)

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

RED MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

GREEN MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

BLUE MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

AMBER MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

4

LED

SMOOTH

RED Min default = 0

RED Max default = 100

BLUE Min default = 0

BLUE Max default = 100

GREEN Min default = 0

GREEN Max default = 100

AMBER Min default = 0

AMBER Max default = 100

SMOOTH

Range = Off – 20

Default = 4

17

13- DISPLAY FUNCTIONS

LED

GAMMA CORRECTION

This menu allow to select

between Linear current output

or Quadratic current output for LEDs

Default = Quadratic

OUTPUT FREQUENCY

This menu allow to adjust

the PWM frequency value (Hz)

in order to reduce flickering in

the process of your camera

recordings

BOOST DRIVING

This menu allow to increase

the LED‟s current from 350 mA

to 500 mA

AUTO

AUTOMATIC MODE

Automatic demo game

without DMX controller

STEP 01/16

Chase with 16 steps previously

created in REC MODE

Speed time, Wait time, Dimmer, Pan,

Tilt and Zoom values selectable by user.

PERSONAL COLOURS

RGBA, Dimmer, Shutter, Pan, Tilt and

Zoom values selectable by user.

RAINBOW

Rainbow colours effect.

Speed time, Dimmer, Shutter, Pan,

Tilt and Zoom values selectable by user.

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

AUTO

SURE?

Menu - NO

Enter - YES

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

01/16

AUTO-PROGRAM

STEP

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

120

AUTO-PERS.COL.

RED

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0010

AUTO-RAINBOW

SPEE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

QUAD

LED

GAMMA CORR.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

610

LED

OUTPUT FREQ.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

ON

LED

BOOST

GAMMA CORRECTION

Linear = Linear current output

Quadratic = Linear light output

(default)

OUTPUT FREQUENCY

Range = 610 Hz – 10 KHz

Default = 610 Hz

BOOST

With BOOST active, the

LED‟s current is set to

500 mA (30% more gain)

Default = Enabled

By setting all the units connected

to the MASTER, to DMX address 1,

them will be synchronized with the

Master unit following the chase

selected on it, including TIME, WAIT,

Pan&Tilt and Zoom position of the

MASTER unit.

18

13- DISPLAY FUNCTIONS

FIXED COLOURS

Sixteen Colour Macros as

on “MACRO” channel.

Dimmer, Shutter, Pan, Tilt and

Zoom values selectable by user.

WHITE MACROS

Sixteen macros for White

color (from 2700 ° K to 8000 ° K

for NICK NRG 1201; from

2700 ° K to 6500 ° K for NICK

NRG 1201 CT).

Dimmer, Shutter, Pan, Tilt and

Zoom values selectable by user.

SLAVE

SLAVE MODE SETTING

This menu allow to set the

NICK NRG 1201 as slave unit.

DMX signal must be present

from MASTER unit (set in

AUTO MODE) in order to ran

the units in SLAVE mode.

By setting all the SLAVE units

connected to the MASTER, to

DMX addess 1, them will be

synchronized with the Master

unit following the chase

selected on it, but running their

own Pan&Tilt and Zoom position.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

1

AUTO-WHITE

WHITE NO.

20 ch

DMX SET

DMX MODE

1

AUTO-FIXED COL.

COLOR

MENU ENTER DOWN

UP

MENU ENTER DOWN

UP

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

SLAVE

PAN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

SLAVE

SURE?

Menu - NO

Enter - YES

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

SLAVE

TILT

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

SLAVE

ZOOM

By setting all the units connected

to the MASTER, to DMX address 1,

them will be synchronized with the

Master unit following the chase

selected on it, including TIME, WAIT,

Pan&Tilt and Zoom position of the

MASTER unit.

The SLAVE unit receive DMX

signal from the MASTER unit.

By setting all the SLAVE units

connected to the MASTER, to

DMX address 1, them will be

synchronized with the Master

unit following the chase selected

on it, but running their own

Pan&Tilt and Zoom position.

19

13- DISPLAY FUNCTIONS

WIRELESS

WIRELESS DMX

Wieless DMX enabled / disabled.

By activating WDMX MODE, it will

be possible to control NICK NRG

1201 via D.T.S. ANTENNA Wireless

DMX Transmitter (cod. 03.E1271).

Wireless DMX Receiver Kit

(Cod. 03.LA.126) on NICK NRG

1201 is available on request.

Logging on NICK NRG 1201 (WIRELESS DMX must be enabled on the unit).

To log on the NICK NRG 1201 in the WIRELESS system simply press and quickly release the function

button on the transmitter .

The transmitter will start flashing rapidly red/green scanning for new free receivers / NICK NRG 1201

units. When a NICK NRG 1201 logs on to the transmitter the LINK green light on transmitter starts to

flash rapidly.

After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting

data. The NICK NRG 1201 now try to synchronize to the transmitter.

When synchronized to the transmitter, 2 different modes are possible:

1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen

on the transmitter and solid display is seen on NICK NRG 1201.

2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on NICK

NRG 1201.

To log off NICK NRG 1201 from a transmitter simply select UNLINK function under WIRELESS DMX

MENU and press ENTER.

When NICK NRG 1201 is logged off the display is blinking, meaning its available for log in on a new

transmitter.

Logging out a NICK NRG 1201.

Select UNLINK function under WIRELESS DMX MENU and press ENTER.

When NICK NRG 1201 is logged off the display is blinking, meaning its available for log in on a new

transmitter.

Logging out all NICK NRG 1201 linked to a transmitter.

Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking

on NICK NRG 1201, it mean that the units are logged out.

Transmitter, Status LED.

Flashing red/green, no dmx connected.

Solid green, dmx signal detected and transmitted.

Fast flashing red/green, log in mode (every free NICK NRG 1201 unit, not logged in to any other

transmitter, will be logged on)

NICK NRG 1201 Status.

Display blinking, not logged on to a transmitter (free).

Solid display, logged on to a transmitter and receiving dmx data.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

WIRELESS

UNLINK

20 ch

DMX SET

DMX MODE

OFF

WIRELESS

SELECTION

MENU ENTER DOWN

UP

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

ON

WIRELESS

SELECTION

MENU ENTER DOWN

UP

MENU ENTER DOWN

UP

Up-Down

Menu

Up-DownENTER

ENTER

WIRELESS DMX SYSTEM

DISABLED (Default)

WIRELESS DMX SYSTEM

ENABLED

UNLINK = LOG OUT

20

13- DISPLAY FUNCTIONS

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it will

be possible to select one of the

16 preprogrammed WHITE cues

that will then ran if DMX signal is

missing or not available.

Useful for Emergency EXIT

illumination on public areas.

Dimmer level, Pan&Tilt and

Zoom values selectable by user.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

OFF

EMERGENCY

SELECTION

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

1

EMERGENCY

WHITE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

255

EMERGENCY

DIMMER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

EMERGENCY

PAN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

EMERGENCY

TILT

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

EMERGENCY

ZOOM

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

ON

EMERGENCY

SELECTION

Up-Down

Menu

Up-DownENTER

ENTER

EMERGENCY

Disabled = Default

EMERGENCY

Enabled

WHITE (1-16)

Default = WHITE 1

DIMMER

Default = 255

PAN

Default = 128

TILT

Default = 128

ZOOM

Default = 0

La pagina sta caricando ...

DTS NICK NRG1200 CT Manuale utente

Questo manuale è adatto anche per

DTS NICK NRG1200 CT Manuale utente

in altre lingue

Documenti correlati

Altri documenti