Panasonic EWBU60W800 Istruzioni per l'uso

Marca: Panasonic

Modello: EWBU60W800

Categoria: Unità di pressione sanguigna

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

EWBU60

Bedienungsanleitung

Operating instructions

Mode d’emploi

Istruzioni d’uso

Instrucciones de funcionamiento

Gebruiksaanwijzing

Instrukcja obsługi

Oberarm-Blutdruckmessgerät

Upper Arm Blood Pressure Monitor

Appareil de mesure de la tension artérielle au bras

Misuratore di pressione sanguigna da braccio

Monitor de presión arterial en brazo

Bloeddrukmeter voor de bovenarm

Ciśnieniomierz naramienny

Model No. EW-BU60

Lesen Sie diese Bedienungsanleitung vor Inbetriebnahme des Geräts

vollständig durch und bewahren Sie sie sorgfältig auf.

Before operating this device, please read these instructions completely and save

this manual for future use.

Avant d’utiliser cet appareil, veuillez lire complètement le présent mode

d’emploi. Conservez-le soigneusement afin de pouvoir le consulter

ultérieurement.

Prima di utilizzare lo strumento, leggere attentamente queste istruzioni e conservare il presente manuale per un

eventuale uso futuro.

Antes de utilizar este aparato, lea detenidamente estas instrucciones y guarde el presente manual para futuras

consultas.

Vóór gebruik deze gebruiksaanwijzing a.u.b. zorgvuldig doorlezen en bewaren voor later gebruik.

Przed rozpoczęciem użytkowania urządzenia należy przeczytać całą Instrukcję i zachować ją na przyszłość.

Contents

Deutsch

Das Panasonic Oberarm-Blutdruckmessgerät Modell EW-BU60 ist ein Gerät zum Messen

von systolischem und diastolischem Blutdruck und Puls beim Erwachsenen, indem eine

unter Druck stehende Manschette am Arm genutzt wird. Das Gerät ist für die regelmäßige

Blutdruck-Selbstmessung konstruiert worden (nicht für z.B. 24-Stunden-Messung).

Für den Fall, dass das Gerät wiederholt Unregelmäßigkeiten erkennt, suchen Sie bitte Ihren

Arzt auf.

Personen mit Herzschrittmachern, Herzrhythmusstörungen, Gefäßverengungen,

Leberfunktionsstörungen oder Diabetiker sollten ihren Arzt aufsuchen, da in solchen Fällen

unterschiedliche Messwerte gemessen werden können. Das Gleiche gilt auch während der

Schwangerschaft.

Wenn dauerhaft erhöhte oder unregelmäßige Hochdruckwerte angezeigt werden

kontaktieren Sie bitte Ihren Arzt.

English

Panasonic Upper Arm Blood Pressure Monitor Model EW-BU60 is a device intended to

measure systolic and diastolic blood pressure and pulse rate of an adult individual by using a

pressurized cuff on the arm. The device is designed for people who have an intention of

measuring blood pressure value periodically by self measurement and not intended for

continuous BP measurement (e.g. 24h measurement).

In case the device repeatedly detects irregularities, please consult your doctor.

People with cardiac pacemakers, cardiac arrhythmia, vascular constriction, liver disorders or

diabetics should consult their doctor as different values may be measured in such cases. The

same also applies during pregnancy.

Contact health professionals if prehypertensive or hypertensive values are indicated.

Deutsch de1

English en1

Français fr1

Italiano it1

Español es1

Nederlands nl1

Polski pl1

Français

L’appareil de mesure de la tension artérielle au bras Panasonic de référence EW-BU60 est

un modèle qui vise à mesurer la pression artérielle systolique et diastolique ainsi que la

valeur du pouls d’un individu adulte, en enfilant un brassard section de mesure sur le bras.

L’appareil est uniquement conçu pour un individu adulte qui a l’intention de prendre lui-

même son pouls de manière ponctuelle. L’appareil ne convient donc pas à une prise de

pouls continue (par exemple une prise de mesures pendant 24 heures).

Au cas où l’appareil détecterait un pouls irrégulier, veuillez consulter votre médecin.

Les personnes dotées d’un stimulateur cardiaque ou souffrant d’arythmie cardiaque, de

constriction vasculaire, de troubles du foie ou de diabète doivent consulter leur médecin car

des valeurs différentes peuvent être mesurées dans de tels cas. Il en va de même pour les

femmes enceintes.

Contactez des spécialistes de la santé si des valeurs préhypertensives ou hypertensives

sont indiquées.

Italiano

Il misuratore di pressione sanguigna da braccio Panasonic modello EW-BU60 è un

dispositivo studiato per misurare la pressione sanguigna sistolica e diastolica e la frequenza

del polso di un individuo adulto attraverso un bracciale a pressione sul braccio. Il dispositivo

è studiato esclusivamente per l’uso da parte di un adulto per l’automisurazione periodica

della pressione sanguigna e non deve essere utilizzato per la misurazione continua (ad es.

misurazione per 24 ore).

Se si riscontrano delle irregolarità, rivolgersi al proprio medico.

Gli individui portatori di pacemaker cardiaci o che soffrono di aritmia cardiaca, costrizione

vascolare, disturbi al fegato o diabete devono consultare il proprio medico poiché in tali casi i

valori misurati potrebbero differire. La stessa indicazione vale per le donne in gravidanza.

Se si riscontrano valori che indicano pre-ipertensione o ipertensione, rivolgersi a uno

specialista.

Español

El monitor de presión arterial en brazo Panasonic, EW-BU60, es un dispositivo para medir

las presiones sistólica y diastólica y el pulso de un adulto, utilizando un manguito

presurizado en el brazo. El dispositivo se encuentra diseñado para un adulto que desea

medir su presión arterial periódicamente por sí solo y no está diseñado para una medición

de la presión arterial continua (ej. las 24 horas).

En caso que el dispositivo detectara irregularidades, por favor póngase en contacto con su

médico.

Las personas con marcapasos, arritmia cardiaca, constricción vascular, afecciones

hepáticas o diabetes deben consultar a su médico ya que en esos casos pueden obtenerse

medidas diferentes. Lo mismo se aplica durante el embarazo.

Póngase en contacto con su médico si se visualizan valores pre-hipertensión o de

hipertensión con frecuencia.

Nederlands

De Panasonic Bloeddrukmeter voor de bovenarm model EW-BU60 is een apparaat bedoeld

voor het meten van systolische en diastolische bloeddruk en de polsslag van een volwassen

individu door middel van een onder druk staand manchet op de arm. Het apparaat is

uitsluitend ontworpen voor een volwassene met als doel de bloeddruk door zelfmeting

regelmatig te meten en niet bedoeld voor constante bloedmetingen (zoals 24-uur metingen).

Neem contact op met uw arts als het apparaat onregelmatigheden detecteert.

Mensen met een pacemaker, onregelmatige hartslag, vernauwde bloedvaten,

leveraandoeningen of diabetes dienen hun arts te raadplegen, omdat in zulke gevallen

verschillende waarden gemeten kunnen worden. Hetzelfde is van toepassing tijdens

zwangerschap.

Neem contact op met uw arts als pre-hypertensieve of hypertensieve waarden aangegeven

worden.

Polski

Ciśnieniomierz naramienny Panasonic model EW-BU60 jest urządzeniem przeznaczonym

do pomiaru ciśnienia tętniczego krwi skurczowego i rozkurczowego oraz tętna u osób

dorosłych przez zastosowanie mankietu ciśnieniowego na ramię. Urządzenie przeznaczone

jest jedynie dla osób dorosłych, z zamiarem okresowego, samodzielnego pomiaru wartości

ciśnienia tętniczego krwi, nie jest natomiast przeznaczone do stałego pomiaru ciśnienia

tętniczego (np. pomiary 24-godzinne).

W przypadku, gdy urządzenie wykryje nieprawidłowości, należy skonsultować się z

lekarzem.

Osoby z rozrusznikami serca, arytmią serca, zwężeniem naczyń, zaburzeniami pracy

wątroby lub cukrzycą powinni skonsultować się z lekarzem, ponieważ w takich przypadkach

mogą być mierzone inne wartości. To samo dotyczy okresu ciąży.

W przypadku wskazania wartości przednadciśnieniowych lub nadciśnieniowych, należy

skontaktować się z pracownikiem służby zdrowia.

en1

English

Panasonic improves blood pressure assessment

Dear customer, congratulation on the purchase of this Panasonic blood pressure monitor.

Since 1992, Panasonic has been providing blood pressure measuring devices to our

customers in Europe. The product you have purchased has passed our strict quality

control, and shall help you manage your daily blood pressure.

We wish you all the best for your health.

Thanks to modern medical technology measuring blood pressure has now become

uncomplicated. The user-friendliness makes measuring a lot easier, but very often a

mistake can occur when assessing the measured values. In the majority of cases it is not the

whole blood pressure picture that is taken into account but only a single measurement. The

result of this is that more than 70 % of all hypertension sufferers are insufficiently treated or

not treated at all (Source: World Health Organisation (WHO)).

Now Panasonic revolutionizes the treatment of high blood pressure.

Waking up Going to sleep

SYS

DIA

Blood pressure is not a fixed parameter!

The blood pressure fluctuations of this example of a day profile show why a single value is

not suitable for diagnosis and therapy.

For people with high blood pressure a fluctuation of up to 50

mmHg within the course

of a day can occur.

en2

English

Points of interest and information concerning blood

pressure and high blood pressure

The treatment of high blood pressure is one of the most successful forms of treatment in

modern medicine. This applies not only when preventing complications due to high blood

pressure, but also with regard to treating damage following a stroke or heart attack.

Recent studies have proven beyond all doubt that:

1. high blood pressure can be successfully lowered in patients of every age and

2. blood pressure should be stabilized at a low level.

The findings of major recent studies have made it necessary to adjust the formerly

acceptable limits (the World Health Organization (WHO), 1999). In other words, the

traditional limit of 160/95 mmHg as the borderline between normal and high blood pressure

has now been reduced. Consequently, the normal values have been “lowered” by WHO, the

German Hypertension Society and the American Hypertension Committee.

Upper value (SYS.) 140 mmHg

Lower value (DIA.) 90 mmHg

Blood pressure exceeding both or either of

these limits is considered hypertension.

The values should be confirmed by

repeated measurements.

A pathologically high blood pressure is now

defined as follows:

Systolic value of 140

mmHg or more and/or

a diastolic value of 90 mmHg or more–

provided that these values are repeatedly

obtained under standard conditions, i.e. at

rest (measured at three different times on

two different days).

This definition applies regardless of age. What formerly constituted a borderline area with

systolic values betw

een 140 and 159 mmHg and diastolic values between 90 and 94 mmHg

is no longer considered to be a “grey area”, but is quite clearly classed as high blood

pressure. This consequently means that medical treatment is required for blood pressure

values in excess of 140/90 mmHg.

en3

English

Parts Identification

Please check the instrument.

Main unit

Bottom of main unit

Side of main unit

Cuff socket

Adjust button

Display

User selection button

Cuff retaining hook

Off/On Start button

SD memory card slot

Memory/Recall button

Connector (for AC adapter)

AM/PM comparison button

Set button

Battery cover

Cuff

Tube

Tube fastener

Guide plate

Grip

Cuff plug

en4

English

Carrying case

(included accessory)

Includes:

Main unit

Cuff

Batteries

SD memory card

Carrying case

Operating instructions

Guarantee card

CD-ROM

SD memory card (128 MB)

(included accessory)

Write-protect

switch

Notched

corner

Label

Should you require one separately, please

purchase a Panasonic product.

*SD Logo is a trademark.

Writable Write-protected

When the write-protect switch on the SD memory

card is set to the LOCK position, data cannot be

written onto or deleted from the card, and the card

cannot be formatted. When the switch is unlocked,

these functions become available.

AC adapter (EW-2B01)

(optional accessory)

Plug

* Specifications of the product or parts may be changed without prior notice.

en5

English

When Using the Main Unit with Batteries

*Always use alkaline batteries. (4 AA-size LR6 alkaline batteries)

When replacing batteries, always use 4 fresh alkaline batteries of the same type from the

same manufacturer, and replace them simultaneously.

1. Turn the main unit over and remove the battery

cover by sliding it in the direction of the arrow

while pressing lightly on the mark.

2. Check the polarities of the batteries and install

them correctly.

3. Replace the battery co

ver and slide it closed.

Replace batteries when:

The “low battery” indicator is displayed.

No display appears even if the Off/On Start button is pressed.

•

CAUTION:

Always follow the cautions printed on the batteries.

Check the polarities of the batteries and install them correctly.

Remove exhausted batteries promptly.

If the product will not be used for a long time, remove the batteries.

Batteries should be used before their expiration date.

Use after the expiration date may result in injury or staining of the surrounding area due to

generation of heat, bursting, or leakage.

For Batteries

The frequency of use for batteries is approximately 500 measurements (3 times per day)

with fresh Panasonic alkaline batteries (AA-size LR6 alkaline batteries). (Measurement

conditions: Room temperature 23°C; Pressurized to 170 mmHg; Upper arm circumference:

30 cm)

If batteries other than alkaline batteries are used or batteries are used in a cold room, and

when measuring a person with high blood pressure, battery life may be dramatically shorter.

*Use alkaline batteries. (Panasonic Oxyride batteries can also be used.)

Be sure to replace batteries once a year to prevent battery leakage.

Please help protect our environment by respecting national and/or local

recycling regulations when disposing of the device and the batteries at the

end of their useful lives.

•

en6

English

When Using the Main Unit with the AC Adapter

Be sure to use only the exclusive AC adapter (EW-2B01).

Use of other AC adapters may result in an accident, electric shock or fire.

1. Insert the AC adapter plug into the connector

on the side of the main unit.

2. Plug the power cord fully into the AC outlet.

Caution when using only the AC adapter

When no batteries are installed in the main unit and the AC adapter is unplugged from the

AC outlet or main unit, the set date and time will be reset and deleted. (Stored data will be

retained.)

Because of this, even when using the AC adapter, it is recommended that batteries be

installed in the main unit.

Setting the time and date

* Please be sure to set the date and time before taking the first measurement after

purchasing the blood pressure monitor or after changing the batteries.

*Please read the “Caution when using only the AC adapter” on page en6.

1. Insert the batteries.

Or, connect the plug of the AC adapter to the connector at

the side of the main unit with no batteries inserted.

The number for the year will flash.

It will be set to “January 1, 2009 0:00” automatically when

the Off/On Start button is pressed or no button is pressed

for 30 seconds during the setup.

2. Adjust the year.

Press the Adjust button “2” to adjust the number of year.

Setting range for years is from 2009 to 2040.

Pressing the Adjust button “2” will return it to 2009 when

“2040” is displayed.

•

3. Adjust the date.

(1) Press the Set button “1”. The date and time will be

displayed and the number for the date will ﬂash.

(2) Press the Adjust button “2” to adjust the number of the

date.

4. Adjust the month.

(1) Press the Set button “1” and the number for the month

will ﬂash.

(2) Press the Adjust button “2” to adjust the number of the

month.

en7

English

5. Adjust the hour.

(1) Press the Set button “1” and the time will ﬂash on and off.

(2) Press the Adjust button “2” to adjust the number of the

hour.

6. Adjust the minutes.

(1) Press the Set button “1” and the number for minutes will

ﬂash.

(2) Press the Adjust button “2” to adjust the number of

minutes.

7. Finally, synchronizing with a time signal, press the Set

button “1” to complete the procedure.

Date and time will be continuously displayed after the setting

is completed.

Turning off the display of date and time

Date and time will not be displayed when the Adjust button “2” is pressed.

In this status the date and time will not be displayed until the Adjust button “2” is

pressed again.

Readjusting date and time

1. Press the Set button “1” for 3 seconds or

longer while the unit is turned off.

The set year will flash.

2. Readjust the date and time following steps 2–

7 on pages en6 and en7.

Setting the time and date (continued)

en8

English

Preparing the SD memory card

* Insert and remove the SD memory card while the unit is turned off.

The stored data may be damaged if performed while taking measurements or writing data.

* Use a Panasonic SD memory card. Other SD memory cards may malfunction or destroy

data.

* This unit is not compatible with SDHC memory cards.

Notched corner

Label

SD memory card

1. Check the direction of the SD memory card, and

insert it into the SD memory card slot on the

side of the unit.

* Insert so the label will be facing forward, and the

notched corner is at the top.

The mark will appear on the display.

The mark is continuously displayed while the

SD memory card is inserted.

•

Removing the SD memory card

Press the SD memory card until you hear

a “click”, and pull the partially ejected card

straight out.

The mark on the display will disappear.

en9

English

Preparing the SD memory card (continued)

Caution when using the SD memory card

Since the SD memory card is a precision device, do not leave it in a place with a high

temperature, exposed to direct sunlight, or where electromagnetic waves or static

electricity are generated.

Also, do not bend, drop, or apply strong vibration to it.

It is recommended to save the important measurement data on a PC or similar since the

data on the SD memory card may get damaged or erased. Panasonic is not liable for

any losses caused by the damaged or erased data in any way.

Do not touch the terminals on the reverse side of the SD memory card.

Regarding the usage of the measurement data, manage and handle under the

responsibility of the user, considering the privacy of the measurer.

The SD memory card has a write protect function. Writing and erasing of the data, and

formatting of the SD memory card will not be possible when the function is enabled.

It may damage not only the blood pressure monitor, but also the SD memory card if the

SD memory card is inserted in the wrong direction. Make sure to insert with the label

side facing forward.

The unit needs to check the folder structure of the stored data on the SD memory card

when the SD memory card is inserted. The

mark will ﬂash on the display during the

check.

Do not operate while the mark is ﬂashing.

Do not remove the SD memory card while writing the data. It may damage the stored

data.

Number of the measurements that can be stored on the SD memory card may differ

depending on the environment.

The data will not be able to playback correctly on the blood pressure monitor if the

image data or the folder in the SD memory card is edited, or the name of the data is

changed.

(This information is as of July 2009, and it may be revised in the future.)

SD memory cards with a size of up to 2 GB can be used with this blood pressure

monitor.

•

Folder structure of the SD memory card

SD memory card PRIVATE PEWGROUP BPM NO1.CSV

Measurement values of each user

stored on the SD memory card

NO2.CSV

NO3.CSV

NO4.CSV

NO5.CSV

en10

English

Contents of data

Day

Month

Year

Hour

Minute

Systolic

Diastolic

Pulse rate

Body movement

Irregular pulse

These contents are

not displayed

18 11 2009 7 3 126 79 76 0 0 1 0

These contents are

displayed

18 11 2009 23 6 145 76 71 0 0 0 1

19 11 2009 7 19 141 72 71 0 0 1 0

19 11 2009 12 16 143 60 65 0 0 0 0

19 11 2009 12 52 150 91 74 0 0 0 0

Wrapping the cuff

Approximately 2 to 3 cm

from inside of elbow

Shoulder Elbow

1. Remove the cuff from the hook.

2. Insert the plug into the socket all the way in.

3. Tuck the arm through the cuff.

Hold on to the cuff by placing your thumb on the grip

of the guide plate.

4. Wrap the cuff aligning the guide plate to the line

extended from the middle finger with palm facing

up.

Wrap the cuff on bare skin.

Set apart 2 to 3 cm from the elbow joint.

Wrap the cuff with a gap of 1 or 2 fingers.

Be careful that the cuff is not too tight.

Press the tape fastener down well to fasten the cuff.

5. When the tube is pointing toward the shoulder,

rotate the tube so it will be pointing toward the

elbow.

Be sure to fix the tube to lie straight using the tube

fastener.

The cuff can be used on either upper arm.

<When wrapping

around right arm>

However, the difference in blood pressure between left

and right arm may be around 10 mmHg. Be sure to

always use the same arm. It is recommended to use

the arm with the higher blood pressure.

•

en11

English

Getting into the measurement position

Sit quietly and relax while taking measurements.

Take a measurement on a desk that will bring the

cuff to the height of the heart.

* Differences in height will cause differences in blood

pressure values.

1. Place the elbow on the table or on something similar.

2. Align the height of the cuff and the heart.

3. Relax with your palm facing up.

Use the same upper arm with the same posture at the same time every day.

We recommend three measurements a day.

First ....... Upon W

aking (Because, with almost no influence from body movement, the

blood pressure is closest to that at night.)

Second ... Before Lunch (Because, with no influence from the meal, it provides blood

pressure values close to the highest of the day.)

Third ....... At Bedtime (So as to obtain data close to your average blood pressure values

during the day.)

This way, by taking measurements morning, noon and night, you can use the unit to learn

the patterns of and monitor your blood pressure.

In the following situations, accurate measurements cannot be taken.

Within 1 hour after eating or drinking alcohol

Immediately after drinking coffee or tea, or smoking

In a moving vehicle

Immediately after exercising or taking a bath

(Wait at least 20 minutes and take a measurement while staying quiet.)

In cold places

(Take measurements at room temperatures around 20 °C.)

When you need to urinate

(Wait several minutes after urinating before taking measurements.)

Be sure to follow the following points for accurate measurements:

Do not move your body, arm, or ﬁngertips.

Do not touch the main unit or the cuff during measurement.

Do not talk.

Do not use a cellular phone near the main unit.

Not following these points may make it impossible to obtain accurate measurements.

•

en12

English

Taking a Reading

1. Press the Off/On Start button.

After the entire display has been lit, the cuff will be pressurized

and measurement will be taken automatically.

The pressure value, mark, and the time will be displayed.

•

The heart mark will flash and the unit will beep when pulse is

detected during depressurization.

•

2. After the measurement is completed, the unit will beep, and

the blood pressure value and pulse rate will be displayed.

The cuff is depressurized automatically.

If the measured value is in the high blood pressure region, the

values will flash for approximately 5 seconds.

The mark or mark will display after flashing for

5 seconds when movement of the body or irregular pulses were

detected during the measurement. (See pages en17 and en18.)

The “no.1” mark will be lit, and mark will flash.

The mark is displayed at the pulse rate display area when the

pulse rate could not be measured.

•

3. To store the measured values, proceed to page en14.

To complete the measurement, press the Off/On Start button.

* If you forget to switch off the unit it will do so automatically after

approx. 2 minutes.

Date and time is displayed when the display of date and time is

set to ON.

See page en7 to turn off the display.

•

en13

English

Taking a Reading (continued)

Taking a measurement with manual pressurization

Take a measurement with manual pressurization if appropriate pressurization is not

possible after repeated pressurization.

Value 30–40 mmHg higher than

expected systolic blood pressure

1. With the unit turned off, press the Off/On Start

button and hold it to pressurize the cuff to 30–40

mmHg higher value than the expected systolic blood

pressure.

The pressurization value on the display will increase

from 0 mmHg while holding down the Off/On Start

button.

It can be pressurized up to 280 mmHg.

CAUTION:

It may cause temporarily internal bleeding when

pressurized more than necessary.

•

2. Release the Off/On Start button.

When an Error Occurs During Measurement

A will appear on the display to indicate that measurement was

unsuccessful and should be performed again.

Before performing another measurement, always press the Off/On Start button to turn off

the unit and make sure to allow a rest period of 4 to 5 minutes before starting again.

Advice:

In general, blood pressure measurements are lower for the second measurement

because you are less nervous and are more tranquil.

For people who easily get tense, measuring twice each time is very effective.

It is recommended to store all values when performing two measurements or more.

When taking two measurements, always stay quiet for 4 to 5 minutes after the first

measurement before taking the second measurement.

en14

English

Storing blood pressure readings

This unit can store a maximum of 540 measurement values.

It is possible to divide the 540 records stored by a maximum of 5 users.

(Initial setting is 2 users. See page en16 to change the number of users.)

Also, it is possible to store more than 2.5 million measurements into supplied SD memory

card (128 MB).

After the measurement is completed, the “no.1” mark will be lit,

and the mark will flash.

1. Press the user selection button to select the desired user

if the user number is different.

The user numbers “no.2

(3, 4, 5) no.1 no.2” will be

displayed every time the user selection button is pressed.

•

(After approx.

2 seconds.)

(After approx.

2 seconds.)

(After approx.

2 seconds.)

(After approx.

2 seconds.)

2. Press the Memory/Recall button and the memory storage

is completed.

The mark will be displayed for 2 seconds, and then

the memory number, measurement date and time are

displayed alternately in 2 second intervals.

The measurement values will be stored into the SD memory

card if the SD memory card is inserted.

(At this point, it will also store any past measurement values

for that user in the SD memory card if there are any past

measurement values that were not stored in the SD memory

card.)

* The mark will flash while storing to the SD memory card.

Do not remove the SD memory card at this time. It may

damage the data.

When storing the value after reaching the 540 records stored

in the main unit, it will delete the oldest measurement values

and store the new values.

Readings cannot be saved when a measurement has been

unsuccessful (display of the error mark for blood

pressure readings).

Measured values for new users cannot be stored in the main

unit if it has already reached 540 records, but it will be stored

in the SD memory card.

(To store the measured value into the main unit, delete the

measurement values for other users.)

•

Deleting all data stored in memory

(1) Recall the user whom you w

ant to delete using the user selection button.

(2) Recall stored data using the Memory/Recall button.

(3) Press the Memory/Recall button again and hold it (for approx. 3 seconds) until all

readings are deleted.

If everything has been deleted, the selected user mark “no.1 (2, 3, 4, 5)” and will

be displayed.

*See page en21 to delete data on the SD memory card.

en15

English

Calling up readings from memory

When the unit is turned off, or when the date and time are displayed, readings can be

recalled after being saved.

1. Press the user selection button to select the desired

user.

To select user 1 “no.1”:

Do not press any button.

To select other than user 1:

Press the user selection button.

2. Press the Memory/Recall button.

The average readings of all recorded measurements are

displayed.

The average reading of the measurements stored in the SD

memory card is displayed if the SD memory card is

inserted. (Average of up to 1095 measurements)

The average reading of all stored measurements in the

main unit is displayed if the SD memory card is not

inserted.

* It ma

y take some time to display the average reading.

Operation will not switch even if the buttons are pressed

during that time.

The user number and mark will be displayed.

* If there is only 1 measurement recorded, mark will

not be displayed.

•

(After approx.

2 seconds.)

(After approx.

2 seconds.)

3. Press the Memory/Recall button to display readings

starting with the most recent measurement.

Each time the Memory/Recall button is pressed readings

are displayed in order of the most recent measurement.

After the oldest reading in the main unit, it will display the

readings of that user in the SD memory card, in order from

new to old if there are readings for that user in the SD

memory card.

The memory number, measurement date, and time are

alternately displayed.

The measurement date and time are displayed alternately

in 2 second intervals when the reading in the SD memory

card is displayed.

•

4. Press Off/On Start button to exit.

If you forget to switch off the unit it will do so automatically

after approx. 30 seconds.

•

La pagina sta caricando ...

Panasonic EWBU60W800 Istruzioni per l'uso

Marca: Panasonic

Modello: EWBU60W800

Categoria: Unità di pressione sanguigna

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

EWBU60

Scarica il pdf

rapporto

in altre lingue

English: Panasonic EWBU60W800 Operating instructions

Panasonic EWBU60W800 Istruzioni per l'uso

Questo manuale è adatto anche per

Panasonic EWBU60W800 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti