WisyCom MFL Manuale utente

MFL User Manual

RF over Fiber System

 Up to 4 ch’s in a single mode fiber

 Diversity reception antenna remoting

 IFB transmissions remoting

 Integrated tunable filters

 Optical & RF power meter

 Ethernet conn. for remote control

rev.05 (ref. FW 1.15)

Date: 27 May, 2019

MFL User Manual

1

Summary

Front Panel Control and Functions ................................................................................................................................... 2

Rear Panel ......................................................................................................................................................................... 3

System Description ........................................................................................................................................................... 4

Optical receiver and transmitter modules.................................................................................................................... 6

Optical Receiver Module .............................................................................................................................................. 7

Optical Transmitter Module ......................................................................................................................................... 8

TRANSMISSION SYSTEM (MODE: IFB) ....................................................................................................................... 8

RECEPTION SYSTEM (MODE: ANT) ........................................................................................................................... 9

Filter option ................................................................................................................................................................ 10

Link without MUX/DEMUX Module ............................................................................................................................ 11

Optical MUX/DEMUX Module .................................................................................................................................... 11

OMX option ............................................................................................................................................................. 11

OMS option ............................................................................................................................................................. 12

DC Option.................................................................................................................................................................... 14

N48 Option ................................................................................................................................................................. 14

V48 Option .................................................................................................................................................................. 14

SPL option ................................................................................................................................................................... 15

Double OMS option .................................................................................................................................................... 15

Optical link budget ...................................................................................................................................................... 16

Failsafe mode .............................................................................................................................................................. 17

Configuration examples: ................................................................................................................................................. 18

IFB TRANSMISSION – MODE: IFB ................................................................................................................................ 18

RECEPTION - MODE: ANT............................................................................................................................................ 19

MULTI-CARRIERS TRANSMISSION – MODE:<n>ifb ..................................................................................................... 20

OLED Display ................................................................................................................................................................... 21

MFL Info screen .......................................................................................................................................................... 21

Main screen ................................................................................................................................................................ 21

Menu Tree ...................................................................................................................................................................... 22

Main menu .................................................................................................................................................................. 25

TX Link menu............................................................................................................................................................... 26

RX Link menu .............................................................................................................................................................. 27

Alarm List .................................................................................................................................................................... 28

Troubleshooting .......................................................................................................................................................... 30

Safety instruction ............................................................................................................................................................ 31

ITALY ONLY .............................................................................................................................................................. 32

TECHNICAL SPECIFICATION ............................................................................................................................................ 33

MFL User Manual

2

FRONT PANEL CONTROL AND FUNCTIONS

MFL allows an easy and quick configuration using buttons, push knobs and display.

The front panel is functionally divided in the following section:

A – LINK STATUS

Transmitter / Receiver configurations

❶ Connection status:

 The first column of LEDs indicate Alarms

 The ON column indicate if a module is ON

 The FAILSAFE column indicate if the Failsafe option is enabled

 STATUS and CONN, showing the LED indications of the Ethernet module on the rear panel

❷ Display (64 x 256 pixels yellow OLED display)

❸ 3 push buttons (membrane). The function of each button (upper, middle and lower) will be readable

from the contextual menu on the display.

❹ Warning (YELLOW) and Alarm (RED) light indicator

❺ Push rotary knob. Rotate and push to select.

B – LINK DIAGRAM

This part shows the block diagram of one complete channel and the BOOSTER supply if enabled from the

transmitters

C – TEMPERATURE ALARMS & CONFIGURATION LABEL

TEMP. ALARM: indicate eventually high temperature on the device.

FAN1/FAN2: these LEDs turn on if faults occur to the cooling system.

CONFIGURATION LABEL: name and configuration of the device.

D - LOCK & POWER

LOCK: it locks the editing of the display.

POWER: ON/OFF square powering button turns on/off the MFL. Above the power button, there are two

LEDs to indicate the type of power supply.

NOTE: If both AC/DC power are supplied, both LEDs turn on but the device uses only AC power supply

A

B

C

D

❶

❷

❸

❺

❹

MFL User Manual

3

REAR PANEL

❶ ❷❸ ❹ ❺ ❻ ❼ ❽ ❾ ❿⓫ ⓬ ⓭ ⓮ ⓯ ⓰ ⓱

⓲ ⓳ ⓴

❶ AC Power Plug AC mains power input, IEC Connector 90-264 Vac

❷ Product label with Serial Number and Options installed

❸ Ground point To connect the MFL rack frame to ground

❹ DC Power Plug (only with MFL-DC option) DC power input, 10-28Vdc, Max 5A

❺ Ethernet socket (RJ45) for connection to a network or computer

❻ Auxiliary optical Input/Output Connector

❼ Optical Input/Output Connectors where the optical signals are divided by wavelength

❽ Optical Input/Output Connector where the optical signals are multiplexed (only with MFL-OMX

option)

❾ Optical safety label

❿ Output N connector female 50Ω (*)

⓫ Orange label: relative laser wavelength = 1570 nm

⓬ Output N connector female 50Ω (*)

⓭ Yellow label: relative laser wavelength = 1550 nm

⓮ Input N connector female 50Ω with switchable 12V boosting power (only on transmitter modules) (*)

⓯ Green label: relative laser wavelength = 1530 nm

⓰ Input N connector female 50Ω with switchable 12V boosting power (only on transmitter modules) (*)

⓱ Blue label: relative laser wavelength = 1510 nm

⓲ BNC-F connector 50Ω for failsafe option (on receivers modules) (*)

⓳ BNC-F connector 50Ω to connect the output of an external filter (on transmitters modules) (*)

⓴ BNC-F connector 50Ω to connect the input of an external filter or for failsafe option (on transmitters

modules) (*)

* In this example. Other configurations on request.

TX*

RX*

MFL User Manual

4

SYSTEM DESCRIPTION

MFL provides wideband optical link for up to 4 RF channels combined in one single mode fiber thanks to

CWDM technology. It is designed to allow for a flexible and modular configuration thanks to a mainboard

that can be fitted with up to 4 plug-in boards that can be chosen any combination of two types:

• TX: Laser optical transmitter, (CDWM) plug-in board

• RX: Optical-receiver plug-in board

To simplify the usage we give a name of the final configuration that easy identify the CWDM channels and

a color code for the RF connectors (N type). We use as default 4 laser wavelength although the CWDM

standard can allow to use much more with a 20nm wavelength separation:

 Channel 51 short name for wavelength 1510 nm

 Channel 53 short name for wavelength 1530 nm

 Channel 55 short name for wavelength 1550 nm

 Channel 57 short name for wavelength 1570 nm

Wavelength and Color Coding:

Example of some possible configurations:

- MFL-TTTT is a 4 laser transmitters on channel 51/53/55/57 (λ = 1510/1530/1550/1570 nm)

- MFL-RRTT has 2 receivers on ch. 51/53 and 2 transmitters ch. 55/57 (it works with MFL-TTRR)

- MFL-TTRR has 2 transmitters on ch51/53 and 2 receivers on ch. 55/57 (it works with MFL-RRTT)

- MFL-TT-- has 2 transmitters on ch51/53

Channel

Wavelength

Color

Identifier

51

Wavelength 1510 nm laser, single mode

Blue

53

Wavelength 1530 nm laser, single mode

Green

55

Wavelength 1550 nm laser, single mode

Yellow

57

Wavelength 1570 nm laser, single mode

Orange

NAME

Ch. 51

Ch. 53

Ch. 55

Ch. 57

MFL-TTTT

T

NAME

Ch. 51

Ch. 53

Ch. 55

Ch. 57

MFL-RRTT

R

T

NAME

Ch. 51

Ch. 53

Ch. 55

Ch. 57

MFL-TTRR

T

R

NAME

Ch. 51

Ch. 53

Ch. 55

Ch. 57

MFL-TT--

T

-

MFL User Manual

5

Following the main code and option that can build up a MFL system:

To verify the installed options list,turn on the unit keeping pressed the front panel knob.

Code

Description

❶

MFL [BASE]

WIDEBAND RF OVER FIBER MAINBOARD

19' 1U Rack units , aluminium frame

Oled display - Ethernet - failsafe switch - realtime clock

AC Powered 230V

❷

RX Module

Optical RX module for MFL (CWDM)

❸

TX Module

Laser TX module for MFL (CWDM), wavelength 1510/1530/1550/1570 nm

❹

DC

DC power supply (10÷28Vdc) on XLR-4M connector

N48

Neutrik OPTICAL DUO connector for fiber and DC power supply (15÷48Vdc)

V48

DC power supply (15÷48Vdc) on XLR-4M connector

SPLxx

Optical splitter option [1:2],[1:3],[1:4]

Optional

MUX

❺

OMX

Module Mux/Demux for 1:4 CWDM

OMS

Module Mux/Demux for 1:6 CWDM

Filter

❻

BF1 (old)

RF filter 25MHz tuning range over 404÷788 MHz

F41

Tunable filter 430-730MHz, 40MHz of Bandwidth,

Selectable Filter HP: 410/470/510 MHz + LP: 600/700/810 MHz,

Fixed Filter 940 ÷ 960 MHz (Europe/Usa)

F42

Tunable filter 430-730MHz, 40MHz of Bandwidth,

Selectable Filter HP: 470/520/550 MHz + LP: 617/662/698 MHz,

Fixed Filter 940 ÷ 960 MHz (Europe/Usa)

F45

Tunable filter 430-730MHz, 40MHz of Bandwidth,

Selectable Filter HP: 410/470/510 MHz + LP: 600/714/810 MHz,

Fixed Filter 806 ÷ 810MHz (for Japan)

①

④

⑤

⑥

②

③

②

③

②

③

②

③

Max 4 optical

modules (TX/RX)

*

* The images are purely for information. This represent one of

the possible configurations

MFL User Manual

6

Optical receiver and transmitter modules

Optical RX module is designed to convert optical signal into RF signal while Optical TX module converts RF signal to

optical signal.

RX and TX modules can be used for both RECEPTION AND TRANSMISSION SYSTEMS.

When they are used for reception of RF signal from one receiving antenna to a receiver or combiner, both RX and

TX modules have to be configured in “ANT” mode

When they are used for transmission of RF signal from one transmitter to an antenna, both RX and TX modules have

to be configured in “IFB” mode

When they are used for transmission of RF signal from <n> transmitters to an antenna, both RX and TX modules

have to be configured in “<n>ifb” mode. Below the example for 4 carriers (4ifb mode)

MFL User Manual

7

Optical Receiver Module

Optical RX module is designed to convert optical signal into RF signal.

The module is equipped with a Optical Power Meter which measures in real time the received optical power.

Receiver module is designed to work in a range approx. 0.3mW ÷ 3mW (-5dBm÷5dBm). Optical power limits of RX

module can be verify in the menu “RX Link > Receiver param”.

It is advisable to work in this range to minimize the noise generated by

the fiber system and reduce intermodulation issue.

An alarm occurs on the display if detected power is out of this range. If the optical power received is too high, we

suggest to add an optical attenuator as show below:

Wisycom code

description

CNFTGT01

2dB ATTENUATOR SC/APC-SC/APC

By MAIN menu, it is possible to disable the High opt. power alarm. This

parameter is set to enabled as default settings.

Internal RF amplifier allows to adjust gain in 0.5dB steps. Gain range

depends on the hardware revision of the module and configuration set (ANT/IFB/<n>IFB).

In TRANSMITTING IFB mode DC power for external amplifier

can be enabled (only if RXB option is installed, verify on MFL menu)

i.e. PAW:

PAW powered by MFL, provides from 10mW to 200mW

according to the MFL-RX module gain setting

Common settings:

PAW output

power

MFL gain dB

setting

10 mW

-10 dB

50 mW

-3 dB

100 mW

0 dB

200 mW

+3 dB

P

opt

: 0.3 mW ÷ 3 mW

-5 dBm ÷ 5 dBm

MFL User Manual

8

Optical Transmitter Module

Optical TX module is designed to modulate RF signal to optical fiber.

The module is equipped with a RF Power Meter which measures in real time the RF power input.

A dedicate RF BAR menu gives indication of average RF level for each modules.

“0” is the reference level

For TRANSMISSION SYSTEM (MODE: IFB), “0” level means 0dBm

For RECEPTION SYSTEM (MODE: ANT), “0” level means -20dBm (≈87 dBµV)

WARNING:

RF LEVELS HAVE TO REMAIN < “10” in order to avoid intermodulation issue.

NOTE: RF level depends on the band setting (filter).

RF bar are diseabled in TRANSMISSION MODE: <n>ifb

TRANSMISSION SYSTEM (MODE: IFB)

When the module is configured for TRANSMISSION SYSTEM (MODE: IFB), input RF power has to remain with in the

range 0.25mW ÷ 4mW (-6dBm÷6dBm).

Wisycom MTK952 trasnmitter with MS option provides a dedicated port at 0dBm of reference to connect directly

into the MFL TX module.

With different transmitters than MTK952, the user has to make sure that input RF power is within the range, by

adding RF attenuators if input RF power is too high.

P

rf

reference =

P

rf

: 0.25 mW ÷ 4 mW

-6 dBm ÷ 6 dBm

0dB is the reference level

MTK952N

Master conf.

MTK952N

Slave conf.

MFL-TT--

MFL-RR--

Fiber optic cable

up to several tens of kilometers

(depending on the fiber)

Area 1

Area 2

Audio input

0dBm

OTHER TX

With attenuator

PAW

MFL-TT--

MFL-RR--

Fiber optic cable

up to several tens of kilometers

(depending on the fiber)

Area 1

Area 2

TX1

TX2

Directional

Coupler

MFL User Manual

9

RECEPTION SYSTEM (MODE: ANT)

When the module is configured for RECEPTION SYSTEM (MODE: ANT), it is advisable to filter the RF signal in input

and to set the Gain in order to work at 0dB as maximum level (e.g. when the transmitter is close to the antenna).

Wisycom supplies different RF filters models:

 integrated in the MFL (BF1, F41, F45… option)

 integrated in antenna (LFA or ADFA antennas)

 integrated in the booster (BFA booster)

Enabling booster on the menu provides DC power supply to external

booster or active antenna.

MFL User Manual

10

EXTERNAL

FILTER

Filter option

When optical TX module is used in RECEPTION SYSTEM (MODE:ANT) a filter option is recommended.

Select on the TX menu the more appropriate

filter according to the frequency in use

It is possible to use also an EXTERNAL filter connected it on BNC connectors in the rear panel. The

attenuation of external filter can be set in the OPT. CH. menu

Option

Filter type

Range

BF1

Tunable Filter

404-788MHz, 25MHz of Bandwidth

F41

Tunable Filter

430-730MHz, 40MHz of Bandwidth

Fixed Filter

940 ÷ 960 MHz (Europe/Usa)

Selectable Filter

410-600 MHz

410-700 MHz

410-810 MHz

470-600 MHz

470-700 MHz

470-810 MHz

510-600 MHz

510-700 MHz

510-810 MHz

F42

Tunable Filter

430-730MHz, 40MHz of Bandwidth

Fixed Filter

940 ÷ 960 MHz (Europe/Usa)

Selectable Filter

470-617 MHz

470-662 MHz

470-698 MHz

520-617 MHz

520-662 MHz

520-698 MHz

550-617 MHz

550-662 MHz

550-698 MHz

F45

Tunable Filter

430-730MHz, 40MHz of Bandwidth

Fixed Filter

806 ÷ 810MHz (for Japan)

Selectable Filter

410-600 MHz

410-710 MHz

410-810 MHz

470-600 MHz

470-710 MHz

470-810 MHz

510-600 MHz

510-710 MHz

510-810 MHz

MFL User Manual

11

Link without MUX/DEMUX Module

Optical link without MUX/DEMUX Module requires one SC/APC single mode fiber to link each TX/RX module (up to 4

fibers)

Optical MUX/DEMUX Module

Thanks to the optical MUX/DEMUX module it is possible to carry with a single fiber several optical signals.

OMX option

With OMX option the MUX/DEMUX module combine/split

o 4 optical signals related to RF over fiber

(1510nm/1530/1550/1570nm)

o ausiliary optical signal in the second

window “1300 WideBand” to embed

other optical signal in range 1260÷1360nm

(e. g. Optical signal from Camera)

Optical connections:

MFL User Manual

12

OMS option

With OMS option the MUX/DEMUX module combine/split

 4 optical signals related to RF over fiber

(1510nm/1530/1550/1570nm)

 ausiliary optical signal in the second window “1300

WideBand” to embed other optical signal in range

1260÷1360nm (e.g. Optical signal from Camera or

Etehernet traffic throght Media Converter)

 optical signals at 1590nm & 1610nm to manage Data

(Ethernet traffic throught Media Converter)

Optical connections:

With OMS option it is possible to manage remote devices connected throught Ethernet interface to an Ethernet

Switch with SFP input.

MFL User Manual

13

1610nm

NOTE of Ethernet Data connection with OMS:

Use LC/PC-LC/PC patches to connect 1590nm and 1610nm data ports of MFL to the SFP modules of Ethernet switch.

Please, pay attention on TX or RX wavelength. For a proper use, it is necessary to cross one of the LC/PC-LC/PC blue

patch cords.

Fiberbox BX2 system uses SFP module TX@1610nm therefore Wisycom

suggests to use the SFP module with TX@1590nm in the LOCAL AREA.

Wisycom code

description

BRE16021204

patch duplex LC-PC to LC-PC length 3mt

MDT16012101

SWITCH 5 PORTS 10/100/1000 + SFP slot, UBIQUITY ER-X-SFP

DO NOT connect ethernet cable

Ubiquity switch port [eth0] as it is for

monitoring (not switched)

MDT14100302

CWDM SFP MODULE 1610nm BROWN 1000BASE BI-DIRECTIONAL

MDT14100301

CWDM SFP MODULE 1590nm RED 1000BASE BI-DIRECTTIONAL

MFL User Manual

14

DC Option

This option adds a DC power supply module on MFL.

Connector: XLR-4M

pin1: GND

pin2: NC

pin3: NC

pin4: VDC (10-28Vdc, max 5A)

N48 Option

Option N48 mounts an Neutrik opticalCON DUO connector for fiber and DC power supply.

Optical connections:

DC input

18÷50Vdc

pin 1: -Vdc

pin 4: +Vdc

OPTICAL DUO connector:

“A” is connected to the main fiber (I/O)

“B” is linked to the LC/APC connector in the rear panel (as aux port)

V48 Option

Option V48 allows to power the MFL with DC input 18÷50Vdc.

To sum up:

option DC: DC input 10÷28Vdc, XLR-4 connector

option V48: DC input 18÷50Vdc, XLR-4 connector

option N48: DC input 18÷50Vdc, opticalCON DUO Neutrik connector for fiber and DC power supply

MFL User Manual

15

SPL option

SPL option mounts an optical splitter inside MFL. It can be used when it is required to carry the same optical signal

to several remote zones. Different type of splitters are available [1:2], [1:3] or [1:4].

NOTE: Splitter module is NO BI-DIRECTIONAL, it can be used only if all the optical signals go on the same way.

Example of application: transmittion of 4 IEM channels on 2 remote areas

Double OMS option

A double OMS option can be installed on MFL. It can be usefulto receive 2 remote areas in a single MFL (as on the

below example). This configuration

 reduces the number of the fiber cable

 reduce the MFL in the LOCAL area

 allows remote management of both the remote areas

Example of application: reception from 2 remote areas

MFL-2R2R--2OMS

R1A

R1B

MAT244

MFL-TT--OMS

T2A

T2B

MFL-TT--OMS

T1A

T1B

R2A

R2B

Remore

Area2

Remore

Area1

Local Area

MFL User Manual

16

Optical link budget

Optical link depends budget on the amount of losses along the fiber route. These losses vary according to the MFL

configuration and the type of fiber connection.

Calculating optical link budget refers to the following values:

 Single Mode Fiber attenuation is 0.2/0.4 dB/Km,

 optical TX laser power is 4mW (6dBm) and

 sensitivity of receiver module is 0.3mW (-5,22dBm)

 attenuations according to MFL configuration

Device

Attenuation*

multiplexer OMX

1,4 dB

multiplexer OMS

1,7 dB

splitter 1:2

3,7 dB

splitter 1:3

5,5 dB

splitter 1:4

7,9 dB

junction

0,2 dB

*Note that these are indicative values

Example: Fiber system with MFL-TTRR-OMS and MFL-RRTT-OMS

TX laser

6

dBm

multiplexer OMS

-1,7

dB

demultiplexer OMS

-1,7

dB

Internal junctions

-1

dB

Received power with short fiber

=1,6

dBm

Fiber link maximum length is 17 Km (=6.8/0.4) since receiver module sensitivity is -5,22dBm (considering 0.4dB/Km).

Example: Fiber system with MFL-TTTT-OMS-SPL1:2 and MFL-RRRR-OMS

TX laser

6

dBm

multiplexer OMS

-1,7

dB

demultiplexer OMS

-1,7

dB

Splitter 1:2

-3,7

dB

Internal junctions

-1

dB

Received power with short fiber

=-2,1

dBm

Fiber link maximum length is 7,8Km (=3.12/0.4) since receiver module sensitivity is -5,22dBm (considering 0.4dB/Km).

MFL User Manual

17

Failsafe mode

MFL is equipped with failsafe ports to connect a redundant additional MFL link.

Failsafe switches in MFL allow RF re-routing if a fault happens (i.e. no power supply, no RF power or no optical

power). All RF and optical signals are then re-routed on the redundant links automatically.

To keep safe the system against PSU fault:

Connect TX module of MFL link2 to failsafe port of TX module Link1.

Connect RX module of MFL link2 to failsafe port of RX module Link1.

If a fault occurs on PSU (power supply unit) of MFL Link1, RF signal in input of MFL link1 is switched automatically to

the failtsafe port as RF input of MFL Link2.

So when RX module of MFL Link1 recognizes that there is no optical power in input, it takes the signal from failsafe

port. Pay attention to enable failsafe on RX module of MFL Link1.

To keep safe the system against fault on RX module:

Split RF signal in input to TX modules of Link1 and Link2.

Connect RX module of MFL link2 to failsafe port of RX module Link1.

MFL

rx module

MFL

rx module

RF

MFL

tx module

MFL

tx module

MFL

rx module

RF

Enable failsafe on RX module

RF

MFL

tx module

MFL

tx module

MFL

rx module

RF

Enable failsafe on RX module

MFL User Manual

18

CONFIGURATION EXAMPLES:

IFB TRANSMISSION – MODE: IFB

This configuration allows to transmit IFB signals to a remote area.

Above an example of 2 IFB transmission.

In this configuration in the local area each transmitter is connected to a single Tx optical module and the MUX

combines the optical signal in one fiber. In the remote area the DEMUX split the optical signal to 2 RX opt. modules

which convert it into RF. Next, the RF signals are amplified with MTK952 in Slave configuration.

NOTE: Other amplifiers type can be used like PAW, MPA221. Verify if they need DC power and enabled it on the RX

modules.

System setup and configuration:

LOCAL AREA



Connect the 2 transmitters to the 2 TX optical modules (RF input power approx. 0dBm)



Configure the 2 TX opt. modules in MODE IFB, Gain = 0dB



Connect the single mode fiber SC/APC between local MFL and remote MFL

REMOTE AREA



Configure the 2 RX opt. module in MODE IFB, Gain = 0dB

 Set RF power on the MTK952 Slave.

 If used PAW amplifiers:

o enabled Booster in the “OPT. CHANNEL > Booster” menu

o set the RF Gain using “OPT. CHANNEL > Gain” o “SETUP” menu

PAW output power

MFL gain dB setting

10 mW

-10 dB

50 mW

-3 dB

100 mW

0 dB

200 mW

+3 dB

MFL-TT---OMS

MFL-RR--OMS

PAW

Tx1

Tx2

Rx1

MTK952Master

Rx2

MFL-TT---OMS

MFL-RR--OMS

MTK952 Slave

Tx1

Tx2

Rx1

MTK952Maste

r

Rx2

MFL User Manual

19

RECEPTION - MODE: ANT

This configuration allows to receive RF signals from remote antennas.

Above an example of reception of 2 diversity remote antennas.

In this configuration in the remote area 2 antennas are connected to 2 Tx optical module and the MUX combines

the optical signal in one fiber. In the local area the DEMUX split the optical signal to 2 RX opt. modules which convert

it into RF. Next, the RF signals are connected to the receiver.

System setup and configuration:

REMOTE AREA



Connect the 2 antennas to the 2 TX optical modules



Configure the 2 TX opt. modules in MODE ANT

 Enabled filter on each TX opt. modules using “OPT. CHANNEL > Filter” or “B.WIDTH” menu.

 connect the single mode fiber SC/APC between local MFL and remote MFL

 If used antennas with booster or booster:

o enabled Booster in the “OPT. CHANNEL > Booster” menu

o set the RF Gain using “OPT. CHANNEL > Gain” o “SETUP” menu

NOTE: set the Gain in order to work at 0dB as maximum level in the RF BAR (e.g. when you have the

microphone close to the antenna).

REMOTE AREA



Configure the 2 RX opt. modules in MODE ANT

MFL-RR---OMS

MFL-TT--OMS

Rx1

Rx2

Tx1

MRK960

Tx2

La pagina sta caricando ...

WisyCom MFL Manuale utente

WisyCom MFL Manuale utente

in altre lingue

Documenti correlati

Altri documenti