DTS JED Manuale utente

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1 - SYMBOLS ................................................................................................................ 4

2 - GENERAL WARNING ............................................................................................. 5

3 - GENERAL WARRANTY CONDITIONS ................................................................... 5

4 - TECHNICAL FEATURES ........................................................................................ 6

5 - ACCESSORIES ....................................................................................................... 7

6 - IMPORTANT SAFETY INFORMATION ................................................................... 8

6.1 Fire prevention...................................................................................................... 8

6.2 Prevention of electric shock .................................................................................. 8

6.3 Safety ................................................................................................................... 8

6.4 Level of protection against the penetration of solid and liquid objects .................. 9

6.5 Waste Electrical and Electronic Equipment (WEEE) directive .............................. 9

7 - VOLTAGE AND FREQUENCY ................................................................................ 9

8 - INSTALLATION ..................................................................................................... 10

8.1 Safety cable ........................................................................................................ 10

8.2 Protection against liquids .................................................................................... 11

8.3 Movement ........................................................................................................... 11

8.4 Risk of fire .......................................................................................................... 11

8.5 Forced ventilation ............................................................................................... 11

8.6 Ambient temperature .......................................................................................... 11

9 - MAINS CONNECTION ........................................................................................... 12

11.1 Protection ......................................................................................................... 12

10 - DMX SIGNAL CONNECTION .............................................................................. 13

10.1 DMX addresses ................................................................................................ 14

10.2 Selecting the DMX address .............................................................................. 14

11 - FIRMWARE UPDATING ...................................................................................... 14

12 - DISPLAY FUNCTIONS ........................................................................................ 15

13 - AUTOFOCUS CALIBRATING PROCEDURE ..................................................... 22

14 - OPENING THE PROJECTOR HOUSING ............................................................ 23

15 - REMOVING / REPLACING THE ROTATING GOBOS ........................................ 24

16 - PERIODIC CLEANING ........................................................................................ 25

16.1 Lenses and reflectors ....................................................................................... 25

16.2 Fans and air passages ..................................................................................... 25

17 - PERIODIC CONTROLS ....................................................................................... 25

18 - DMX PROTOCOL ................................................................................................ 26

19 - ROTATING GOBO WHEEL ................................................................................. 40

20 - FIXED GOBO WHEEL ......................................................................................... 41

21 - COLOUR WHEEL ................................................................................................ 42

4

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC

SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “SUITABLE FOR

MOUNTING ON NORMALLY FLAMMABLE

SURFACES”

THIS SYMBOL MEANS “SUITABLE FOR

INDOOR USE ONLY”

THIS SYMBOL INDICATES THE MAXIMUM

OPERATING AMBIENT TEMPERATURE

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE FROM THE OBJECTS AND THE

PEOPLE LIT BY THE LIGHT BEAM

THIS SYMBOL MEANS “DO NOT STARE

AT THE OPERATING LIGHT SOURCE”

THIS SYMBOL INDICATES

PHOTOBIOLOGICAL SAFETY

THIS SYMBOL INDICATES THE EUROPEAN

COMMUNITY DIRECTIVE 2012/19/EU ON

WASTE ELECTRICAL AND ELECTRONIC

EQUIPMENT (WEEE)

!

5

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The unit is not for household use and must be installed by a qualified electrician or

experienced person.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

WARNING!

NEVER EXPOSE THE FRONT LENS

TO SUNLIGHT FROM ANY ANGLE

TO AVOID DAMAGE OF

HEAD INTERNAL PARTS.

Front lens could become powerful

magnifying glass if exposed towards the

sun or any strong artificial light source;

this can cause damage of head internal

parts, even for few seconds and even

when the unit is off.

The last command before switch off:

point the front lens down towards the

ground.

6

4- TECHNICAL FEATURES

DTS Product Code:

03.MS020.L JED Black finishing

LED

60W RBL (Red, Blue, Lime Green)

Optical group

Custom built optical group

2° - 19° zoom range (Beam-Spot mode)

4,5° - 26° zoom range (Wash mode)

Linear motorized focus

Auto Focus

Color generation

Advanced RBL color synthesis

Lime green color for brightness enhancement

RBL independent strobe color pulse

2-tone color generation

16-color wheel

Dynamic effects

Overlapping wheels for multiple effects:

Customizable rotating gobo wheel (8 gobos + Open)

Fixed gobo wheel (13 gobos + Animation sector + Open)

8-facet rotating prism

Interface / Control / Programming

DMX 512 / RDM

Auto flip LCD graphic display + 4 soft-keys

Internal updatable operating system

DMX

28 DMX channels

Pan & Tilt

Pan: 540° rotation

Tilt: 270° rotation

Power supply

Full-range 100-240Vac 50-60 Hz

Consumption: 150VA

Connections

Power supply: PowerCON TRUE1 In&Out panel connectors

DMX: XLR 3 and 5 pins In&Out panel connectors

Operating ambient temperature

-10° / 40°

Internal safety devices

Overvoltage circuit protection and overtemperature circuit protection

7

International certifications

CE certification

Weight

11,9 Kg

Dimensions

5- ACCESSORIES

As standard

1 x PowerCON TRUE1 female cable connector (Code 0520P066)

1 x XLR 5 pins female cable connector (Code 0508B147)

1 x XLR 5 pins female cable connector (Code 0508B148)

1 x G-Quick clamp with “Fast Lock” connection 1/4 turn (Code 0521A014)

1 x User’s manual

Optional (on request)

• Omega bracket with “Fast Lock” connection 1/4 turn (Code 02K00467)

• Aliscaf clamp for tube diameter 50 mm (max load 100Kg) (Code 0521A008)

• “C” Clamp G60 (max load 50 Kg) (code 0521A004)

• Safety cable (3mm x 60 cm), max capacity load 60Kg (Code 0521A010)

8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

-It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

-Minimum distance from the objects and the people lit by the light beam: 0,5 m.

-Replace any blown or damaged fuses only with those of identical value (T 2A 250V).

Refer to the wiring diagrams if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit.

Unplug the unit prior to performing any function which involves touching the inside of

the moving head.

-The level of technology inherent in the JED requires the assistance of specialised

personnel for all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Safety:

-Risk Group 2 product according to EN 62471.

CAUTION. Do not look directly into the light output and do not view the light beam with

optical instruments or any device that may concentrate the beam.

May be harmful to the eyes and skin.

-Do not stare at the operating light source.

-The light source contained in this luminaire shall only be replaced by the

manufacturer or his service agent or a similar qualified person.

-The unit is not for household use and must be installed by a qualified electrician or

experienced person.

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a safety cable to sustain the weight of the unit in case of the failure of the

main fixing point.

-The external surface of the unit, at various points, may exceed 50°C. Never handle

the unit until at least 5 minutes have elapsed since the unit was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

!

9

6.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the

penetration of solid and liquid objects is IP20.

Suitable for indoor use only.

6.5 Waste Electrical and Electronic Equipment (WEEE) directive:

- The projector, accessories and packaging should be sorted for environmental-friendly

recycling.

For EC countries: according to the European Directive 2012/19/EU for Waste

Electrical and Electronic Equipment and its implementation into national right,

luminaires that are no longer usable must be collected separately and disposed of in

an environmentally correct manner.

7- VOLTAGE AND FREQUENCY

JED operates at 100-240Vac 50-60 Hz.

!

10

8- INSTALLATION

The unit is suitable for dry locations only.

JED may be either floor or ceiling mounted.

For floor mounting installations, JED is supplied with four rubber mounting feet on the

base.

For ceiling mounted installations, we recommend the use of appropriate clamps to fix

the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hang it.

The structure should also be sufficiently rigid so as not to move or shake whilst the

JED is moving.

Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the

JED by using a G-Quick clamp (provided in the box) or a Omega bracket in

conjunction with Aliscaf clamp (Omega bracket and Aliscaf clamp are available on

demand).

8.1- Safety cable

A safety cable must be securely fixed to the JED and to the suspension truss in order

to avoid the fixture accidentally falling should the main fixing point fail.

Make sure that the safety cable or chain can bear the weight of the entire unit.

A suitable safety cable (code 0521A010) is available on demand.

You may attach the safety cable to the attachment point (A) located on the base of the

fixture, as shown in the picture below.

!

11

8.2 Protection against liquids

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

8.3- Movement

Pan: 540° rotation ; Tilt: 270° rotation.

Do not place any object in the path of the projector’s movement.

8.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

Minimum distance from the objects and the people lit by the light beam: 0,5 m.

8.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans

located on both the base and head of the fixture.

These should, under no circumstances, be blocked or obstructed whilst the projector

is in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

8.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should not exceed 40°C.

!

12

9- MAINS CONNECTION

JED operates at 100-240Vac 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 1 amps

at 230Vac or 2 amps at 100Vac each unit connected.

Strict adherence to regulatory norms is strongly recommended.

MAINS INPUT 100-240Vac 50-60 Hz

PowerCon TRUE1 male panel connector

MAINS OUTPUT 100-240Vac 50-60 Hz (MAX 16A)

Max 14 JED units @ 230Vac

Max 7 JED units @ 100Vac

PowerCON TRUE1 female panel connector

FUSE T 2A 250V

9.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each JED.

A good earth connection is essential for the correct operation of the projector.

!

13

10- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 signal.

Connection between the mixer and the projector or between projectors must be carried

out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors

has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest

to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

14

10.1-DMX Addresses

JED can be controlled with 28 DMX channels.

In order to use the unit in 28 DMX channels mode, set the following addresses on the

mixer:

Projector 1 A001

Projector 2 A029 If you want to select the next projector, just add “28”

Projector 3 A057

….. A….

projector 6 A141

10.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now setted to the new DMX address.

TRICKS:

If you keep pushed the UP or DOWN keys, the channels are calculated more quickly

and you get a faster selection.

11- FIRMWARE UPDATING

To update the firmware release of the JED you need:

- DTS Dongle Firmware Uploader (code 03.LA.206).

- “DTS Firmware Upgrade Utility v.2.02” program installed on PC.

- Latest firmware release available for JED unit.

Updating the firmware release.

Please follow the procedure below to perform the update:

1. Connect the DTS Dongle Firmware Uploader to a spare USB port on the PC.

2. Connect the unit DMX input to the DTS Dongle Firmware Uploader DMX output with

a standard DMX cable and turn ON the unit.

3. Send the new firmware release into the unit by using “DTS Firmware Upgrade

Utility v.2.02” program. At the end of the procedure, the unit will reset.

For more information please refer to an authorised DTS service centre.

15

PAN DIRECTION

NORMAL

MENU ENTER DOWN UP

TILT DIRECTION

NORMAL

MENU ENTER DOWN UP

12- DISPLAY FUNCTIONS

The JED display panel shows all the available functions. Using these functions, it is

possible to change some of the parameters and add some functions. Changing the

DTS setting can vary the functions of the unit so that it does not respond to the DMX

512 used to control it. Carefully follow the instructions below before carrying out any

variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

FIRMWARE RELEASE

21.30

RDM Device Model ID

0x000F

DMX Personality ID

0x01 “28 CHANNELS”

Pan Direction

PAN DIRECTION

This menu allows to set

the Pan movement

Normal or Reversed

Tilt Direction

TILT DIRECTION

This menu allows to set

the Tilt movement

Normal or Reversed

Up-Down

Menu

Up-DownENTER

Up-Down

Menu

Up-DownENTER

ENTER

Pan movement

Normal or Reversed

Default = Normal

Tilt movement

Normal or Reversed

Default = Normal

16

PAN SPEED

4

MENU ENTER DOWN UP

TILT SPEED

4

MENU ENTER DOWN UP

12- DISPLAY FUNCTIONS

Pan Speed

PAN SPEED

Pan Speed control (1-4)

Tilt Speed

TILT SPEED

Tilt Speed control (1-4)

Zoom Speed

ZOOM SPEED

Zoom Speed control (1-4)

Display

DISPLAY FLIP / STAND BY / CONTRAST

Display Flip:

Reverses display's reading depending on

the mounting position

(Automatic, on the ground or suspended).

Display Standby:

To turn off the display (after 5 seconds)

or leave it always on.

Display Contrast:

Display contrast regulation (1-40)

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

Pan Speed control

(1-4)

Default = 4

Tilt Speed control

(1-4)

Default = 4

Up-Down

Menu

Up-DownENTER

ENTER

Display Flip

AUTO (Default)

ON THE GROUND

SUSPENDED

Display Standby

OFF = Display Standby

disabled (Default)

ON = Display goes OFF

after 5 seconds

Display Contrast

1-40 (Default = 25)

MENU ENTER DOWN UP

FLIP

AUTO

DISPLAY

MENU ENTER DOWN UP

FLIP

STANDBY

OFF

DISPLAY

MENU ENTER DOWN UP

FLIP

CONTRAST

25

DISPLAY

Up-Down

Menu

Up-DownENTER

ENTER

Zoom Speed control

(1-4)

Default = 2

ZOOM SPEED

2

MENU ENTER DOWN UP

17

MENU ENTER DOWN UP

ENABLED

BY DMX

RESET

12- DISPLAY FUNCTIONS

DMX Mode

DMX MODE

To select DMX mode:

28 channels

Reset

RESET

Reset via DMX ENABLED / DISABLED

and unit motors reset

Fans

FANS SETTING

STANDARD mode (Default) or

SILENT mode

Gobo Rotation

GOBO ROTATION

Gobo rotation during gobo scrolling

for rotating gobo wheel

Gobo 1

GOBO 1

To use the gobo 1 of the rotating gobo

wheel with a gobo Open Studio (default)

or with a user gobo.

This menu lets you have the correct

focusing for each situation.

Autofocus

AUTOFOCUS

Automatic focusing

Up-Down

Menu

Up-DownENTER

DMX Mode

28 channels

ENTER

MENU ENTER DOWN UP

28 CHANNELS

DMX MODE

Up-Down

Menu

Up-DownENTER

ENTER

ENABLED = Reset via

DMX enabled (Default)

DISABLED = Reset via

DMX disabled

NOW = Instant unit motors

reset

Up-Down

Menu

Up-DownENTER

ENTER

STANDARD mode =

High fans speed: The LED

always works at maximum

power (Default).

SILENT mode = Low fans

speed for a very low noise

operation. The LED may be

dimmed in particular working

conditions.

MENU ENTER DOWN UP

STANDARD

FANS SETTING

Up-Down

Menu

Up-DownENTER

ENTER

ON = Default

OFF

Up-Down

Menu

Up-DownENTER

AUTOFOCUS

ON = Default

OFF

ENTER

AUTOFOCUS

ON

MENU ENTER DOWN UP

GOBO ROTATION

ON

MENU ENTER DOWN UP

DURING GOBO SCROLLING

Up-Down

Menu

Up-DownENTER

ENTER

OPEN-STUDIO = To

have the gobo Open

Studio focusing (default).

USER GOBO = To have

the user gobo focusing.

GOBO 1

OPEN-STUDIO

MENU ENTER DOWN UP

ROTATING GOBO WHEEL

GOBO 1

USER GOBO

MENU ENTER DOWN UP

ROTATING GOBO WHEEL

18

12- DISPLAY FUNCTIONS

LED

LED SETTING

SMOOTH

This menu allows to select the value of

delay (in milliseconds) for RED, GREEN,

BLUE and DIMMER channels reaction

to DMX dimming command.

0 = Instant response

4 = 100 ms smooth response (Default)

20 = 500 ms smooth response

GAMMA CORRECTION

This menu allows to select between

Linear current output or Quadratic

current output for LED.

LINEAR = Linear current output

QUADRATIC = Linear light output (Default)

OUTPUT FREQUENCY

This menu allows to adjust the PWM

Frequency value (Hz) in order to reduce

flickering in the process of your camera

recordings.

Range = 610 Hz – 20 KHz

Default = 610 Hz

BOOST

This menu allows to increase the LED’s

current from 70% to 100%.

Default = ON

System Info

SYSTEM INFO

Unit model; 10 motors board, Pan&Tilt

board and LED Driver board software

version; unit life time and RDM ID

LED life hours

LED LIFE HOURS

RBL and LED Driver board life time

Temperatures

TEMPERATURES

RBL temperature monitoring.

DRV-1 = Red and Lime green outputs of

LED Driver board temperature monitoring.

DRV-2 = Blue output of LED Driver board

temperature monitoring.

MICRO = Micro controller temperature

monitoring.

Up-Down

Menu

Up-DownENTER

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN UP

FLIP

SMOOTH

4

LED

MENU ENTER DOWN UP

GAMMA CORR.

QUAD

LED

MENU ENTER DOWN UP

FREQUENCY

610 HZ

LED

MENU ENTER DOWN UP

BOOST

ON

LED

Up-Down

Menu

Up-DownENTER

ENTER

SYSTEM INFO

MODEL: JED

10M: R.21

PT: R.27

LED: V.1.00

MENU ENTER DOWN UP

UNIT LIFE: 0124H

RDM: 00010EF2

LED LIFE HOURS

RED LIFE:

LIME GREEN LIFE:

BLUE LIFE:

DRV LIFE:

MENU ENTER DOWN UP

0078H

0080H

0069H

0134H

TEMPERATURES

RED:

LIME GREEN:

BLUE:

MICRO:

DRV-1: 037°C DRV-2: 042°C

MENU ENTER DOWN UP

041°C

046°C

049°C

033°C

19

REBOOT

MENU ENTER DOWN UP

12- DISPLAY FUNCTIONS

Reserved

RESERVED

000

MENU ENTER DOWN UP

ENTER CODE

PAN LOCK

NO

MENU ENTER DOWN UP

Up-Down

Menu

Up-DownENTER

Pan Lock = Lock the Pan

to the desired value

Tilt Lock = Lock the Tilt

to the desired value

Pan Free = Remove power

to Pan motor

Tilt Free = Remove power

to Tilt motor

Lock Detector OFF

Lock Detector ON (Default):

This function lets the user to

activate the Lock detector on

Pan and Tilt.

When Lock detector is set to

ON, the unit start the Pan&Tilt

motors reset normally, but if for

any reason there is something

blocking the movement for

Pan&Tilt motors during the

initial reset (example unit into

the flight case and power

connected), it automatically will

stop to reset Pan&Tilt motors

after 5 seconds from the startup

and a warning message (Pan

locked-Tilt locked) will appear

on unit display .

Reboot = Unit Reboot without

needing of turning OFF the unit

Exit To Main = Exit from

Reserved menu

RESERVED

(Code = 100)

Pan lock-Tilt lock

Pan free-Tilt free

Lock Detector

Reboot

Exit To Main

LOCK DETECTOR

ON

MENU ENTER DOWN UP

ENTER

EXIT TO MAIN

MENU ENTER DOWN UP

20

DEFAULT

RESTORE MAIN SETTINGS

MENU ENTER DOWN UP

12- DISPLAY FUNCTIONS

No DMX Action

NO DMX ACTION

This menu allows to set the desired

unit’s behavior in case DMX signal

is missing or not available.

KEEP LAST DMX

Keep last valid DMX signal.

PROGRAM

126 pre-programmed steps.

Speed time values (range 0.2x - 2x)

selectable by user (default 1x).

SINGLE CUE

Fixed cue with values selectable

by user.

BLACK OUT

Black-out

Default

DEFAULT

To restore factory settings

Motors Test

MOTORS TEST

To test all functions in sequence or

single desired function without DMX

controller.

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

NO DMX ACTION

KEEP LAST DMX

MENU ENTER DOWN UP

PROGRAM

STEP 01

NO DMX ACTION

MENU ENTER DOWN UP

SINGLE CUE

RED

NO DMX ACTION

MENU ENTER DOWN UP

BLACK OUT

NO DMX ACTION

MENU ENTER DOWN UP

ALL

MOTORS TEST

MENU ENTER DOWN UP

PAN

MOTORS TEST

La pagina sta caricando ...

DTS JED Manuale utente

DTS JED Manuale utente

in altre lingue

Documenti correlati

Altri documenti