Polycom SoundStation IP 7000 Guida utente

Marca: Polycom

Modello: SoundStation IP 7000

Tipo: Guida utente

Questo manuale è adatto anche per

2200-19000-122

UC Software 4.0.2B | June 2013 | 1725-40119-001 Rev D

SETUP GUIDE

UC Software 4.0.2B | June 2013 | 1725-40119-001 Rev D

undSt

7000

hone

Polycom

SoundStation

IP 7000 Phone Setup Guide

6001 America Center Dr

San Jose, CA 95002

USA

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for

any purpose, without the express written permission of Polycom, Inc. Under the law, reproducing includes translating

into another language or format.

As between the parties, Polycom, Inc., retains title to and ownership of all proprietary rights with respect to the software

contained within its products. The software is protected by United States copyright laws and international treaty

provision. Therefore, you must treat the software like any other copyrighted material (e.g., a book or sound recording).

Every effort has been made to ensure that the information in this manual is accurate. Polycom, Inc., is not responsible

for printing or clerical errors. Information in this document is subject to change without notice.

Trademarks

POLYCOM®, the Polycom logo and the names and marks associated with Polycom products are trademarks and/or

service marks of Polycom, Inc. and are registered and/or common law marks in the United States and various other

countries. All other trademarks are property of their respective owners. No portion hereof may be reproduced or

transmitted in any form or by any means, for any purpose other than the recipient's personal use, without the express

written permission of Polycom.

Disclaimer

While Polycom uses reasonable efforts to include accurate and up-to-date information in this document, Polycom

makes no warranties or representations as to its accuracy. Polycom assumes no liability or responsibility for any

typographical or other errors or omissions in the content of this document.

Limitation of Liability

Polycom and/or its respective suppliers make no representations about the suitability of the information contained in this

document for any purpose. Information is provided “as is” without warranty of any kind and is subject to change without

notice. The entire risk arising out of its use remains with the recipient. In no event shall Polycom and/or its respective

suppliers be liable for any direct, consequential, incidental, special, punitive or other damages whatsoever (including

without limitation, damages for loss of business profits, business interruption, or loss of business information), even if

Polycom has been advised of the possibility of such damages.

Customer Feedback

We are striving to improve our documentation quality and we appreciate your feedback. Email your opinions and

comments to VoiceDocumentationFeedb[email protected]

Visit the Polycom Voice Support Center for software downloads, product documents, product licenses, troubleshooting

tips, service requests, and more.

iii

About This Guide

Thank you for choosing the Polycom

SoundStation

IP 7000 conference

phone. This conference phone provides multi-person audio and video

conferencing capabilities for medium to large conference rooms within a

Session Initiation Protocol (SIP) internet telephony system.

This guide provides everything you need to know to quickly set up your new

conference phone. Verify with your system administrator that the network is

prepared for configuring the conference phone. Also, read the Parts List and

the Safety and Compliance section in this guide before you set up the

conference phone.

This guide includes regulatory compliance information that your system

administrator should review. You can also view this guide from the

SoundStation IP 7000 Support Web page.

Setup Guide for the Polycom SoundStation IP 7000 Phone

Contents

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

1 Setting Up Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2

Installing Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3

Connecting Network and Power Sources . . . . . . . . . . . . . . . . . . . . . . . 1–3

Connecting Optional External Microphones . . . . . . . . . . . . . . . . . . . . 1–8

Connecting Optional Auxiliary Audio Components . . . . . . . . . . . . 1–11

Connecting Optional Video Components . . . . . . . . . . . . . . . . . . . . . . 1–13

Registering Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–16

2 Troubleshooting Your Phone Setup . . . . . . . . . . . . . . . . . . . 2–1

Installation Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2

Power and Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4

Access to Screens and Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5

Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6

Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7

Overall Functioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

Testing Phone Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

Investigating Phone Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . Safety Notices–1

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 1

Setting Up Your Phone

This chapter provides basic setup instructions and information for obtaining

the best performance from your SoundStation IP 7000 conference phone.

The topics include:

• Parts List on page 1-2

• Installing Your Phone on page 1-3

• Registering Your Phone on page 1-16

To read about how to customize and use your phone, see the User Guide for the

Polycom SoundStation IP 7000 Phone, available from the SoundStation IP 7000

Support page.

If you require additional information or assistance with your new phone, see

your system administrator.

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 2

Parts List

The following items are included in your basic phone package:

• SoundStation IP 7000 Conference Phone

• 7.6m (25ft) Network Cable

• Quick Start Guide

Make sure your conference phone package contains each item. If any item is

missing, see your system administrator.

Optional Accessories

The following items are optional accessories for your phone:

• AC Power Kit with:

— Power Adapter

— Regional Power Cord

— Power Insertion Cable

• Multi-Interface Module Package with:

— Multi-Interface Module

— 3.6m (12ft) Network Cable (10-pin)

— Power Adapter

— Regional Power Cord

• 7.6m (25ft) Console Interconnect Cable

• External Microphone Kit with two SoundStation IP 7000 analog expansion

microphones

• One Polycom

Microphone Array with cable

7.6m (25ft) Network Cable

Quick Start Guide

SoundStation IP 7000 Conference Phone

Setting Up Your Phone

1 - 3

• Mobile Device Cables (2.5mm and 3.5mm)

• Computer Calling Cable

• Video Kit with:

— Polycom

Microphone Array Cable

Installing Your Phone

This section describes how to install your phone. It includes the following

topics:

• Connecting Network and Power Sources on page 1-3

• Connecting Optional External Microphones on page 1-8

• Connecting Optional Auxiliary Audio Components on page 1-11

• Connecting Optional Video Components on page 1-13

Connecting Network and Power Sources

There are four ways to connect your phone to the network and a power source.

Your system administrator can tell you which of the following methods best

suits your teleconferencing needs:

• Power over Ethernet (PoE)

• AC Power (One Phone)

• AC Power (One Phone, with Multi-Interface Module)

• AC Power (Two Phones, with Multi-Interface Module)

Connecting Your Phone Using a Power over Ethernet Source

Power over Ethernet is the default connection for your phone.

Note

When you connect your phone to a Polycom

HDX

system or

Polycom

RealPresence

Group system, you do not need to connect your phone

to a power source. To set up your phone with a Polycom HDX system or

Polycom RealPresence Group system, see Connecting Optional Video

Components on page 1-13.

Note

AC power adapters are not included in the PoE package. If you require one, see

your system administrator.

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 4

The following figure shows how to connect your phone to the network using

a PoE source and the 7.6m (25ft) Network Cable.

To connect your phone using a PoE source:

1. Connect the 7.6m (25ft) Network Cable to the LAN jack on your phone.

2. Connect the other end of the 7.6m (25ft) Network Cable to an available

LAN port on the wall or hub/switch device port.

Connecting Your Phone Using AC Power (One Phone)

If a PoE source is not available, connect your phone to an AC power source. To

connect your phone to an AC power source, make sure you have the optional

AC Power Kit (containing a Power Adapter, Regional Power Cord, and a

Power Insertion Cable).

25-foot Network Cable

1 2

Setting Up Your Phone

1 - 5

The following figure shows how to connect your phone to an AC power

source.

To connect your phone to an AC power source:

1. Connect the 7.6m (25ft) Network Cable to the LAN jack on your phone.

2. Connect the other end of the 7.6m (25ft) Network Cable to the

Power Insertion Cable.

3. Connect the Power Insertion Cable to an available LAN port on the wall

or hub/switch device port.

4. Connect the Power Adapter to the Power Insertion Cable.

5. Connect the other end of the Power Adapter (with the attached

Regional Power Cord) to the wall outlet.

Connecting Your Phone Using AC Power (One Phone, with Multi-Interface

Module)

You can connect one phone to an AC power source and the Multi-Interface

Module. In this way, you have access to the auxiliary audio connectors on the

module so you can connect speakers, wireless (lapel) microphones, and

recording devices and computers (to record phone calls).

Before you set up a phone using the Multi-Interface Module, make sure you

have the optional Multi-Interface Module Package (containing a

Multi-Interface Module, 3.6m (12-ft) Network Cable (10-pin), Power Adapter,

and Regional Power Cord).

Power Adapter

Power Insertion Cable

25-foot Network Cable

7.6m (25ft)

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 6

The following figure shows how to connect your phone to an AC power source

and the Multi-Interface Module.

To connect your phone to an AC power source and the Multi-Interface Module:

1. Connect the 3.6m (12ft) Network Cable (10-pin) to the LAN jack on your

phone.

2. Connect the other end of the 3.6m (12ft) Network Cable (10-pin) to the

Multi-Interface Module.

3. Connect the 7.6m (25ft) Network Cable to the Multi-Interface Module.

4. Connect the other end of the 7.6m (25ft) Network Cable to an available

LAN port on the wall or hub/switch device port.

5. Connect the Power Adapter to the Multi-Interface Module.

6. Connect the other end of the Power Adapter (with the attached

Regional Power Cord) to the wall outlet.

Connecting Your Phone Using AC Power (Two Phones, with Multi-Interface

Module)

If you have a larger room configuration, you can connect up to two phones

together. In this case, the phones act as one phone and display the same

information. For more information on how to use your phone when two

phones are connected, see your system administrator.

Multi-Interface

Module

12-foot

Network Cable (10-pin)

25-foot

Network Cable

Power Adapter

3.6m (12ft)

7.6m (25ft)

Setting Up Your Phone

1 - 7

Before you connect two phones together, make sure you have the optional

Multi-Interface Module Package (containing a Multi-Interface Module, 3.6m

(12-ft) Network Cable (10-pin), Power Adapter, and Regional Power Cord)

and the optional Console Interconnect Cable.

The following figure shows how to connect two phones to the network using

AC power.

To connect two phones to an AC power source:

1. Connect the 3.6m (12ft) Network Cable (10-pin) to the LAN jack on the

first phone.

2. Connect the other end of the 3.6m (12ft) Network Cable (10-pin) to the

Multi-Interface Module.

3. Connect the 7.6m (25ft) Network Cable to the Multi-Interface Module.

4. Connect the other end of the 7.6m (25ft) Network Cable to an available

LAN port on the wall or hub/switch device port.

5. Connect the Power Adapter to the Multi-Interface Module.

Multi-Interface

Module

Console

Interconnect Cable

12-foot

Network Cable (10-pin)

25-foot

Network Cable

Power Adapter

3.6m (12ft)

7.6m (25ft)

Warning

Make sure you connect the two phones and the Multi-Interface Module before you

connect the Power Adapter (with the attached Regional Power Cord) to the wall

outlet.

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 8

6. To connect phones, plug one end of the Console Interconnect Cable into

one of the microphone connectors on the first phone and the other end of

the cable into one of the microphone connectors on the second phone.

7. Connect the other end of the Power Adapter (with the attached

Regional Power Cord) to the wall outlet.

Connecting Optional External Microphones

You can connect microphones to your phone using an optional

External Microphone Kit. Depending on the External Microphone Kit you

have, your kit will contain either two SoundStation IP 7000 expansion

microphones (analog), or two Polycom Microphone Arrays (digital).

You connect microphones to the microphone connectors on your phone. Your

phone has two microphone connectors.

The following figure shows the microphone connectors on the back of your

phone.

Warning

When you insert the cable into a microphone connector, make sure the pins on the

cable line up with the microphone connector so that the cable inserts easily. If you

insert the Console Interconnect Cable upsidedown, you may damage the phone.

Microphone Connectors

Setting Up Your Phone

1 - 9

How you connect microphones depends on how you power your phone,

whether you have a one or two-phone setup, and if your phone is connected

to a Polycom HDX system or Polycom RealPresence Group system:

• For information on how to connect microphones to a single phone setup,

see Connecting Microphones to a Single Phone Setup on page 1-9.

• For information on connecting microphones to a two-phone setup, see

Connecting Microphones to a Two-Phone Setup on page 1-9.

• For information on attaching microphones to your phone when your

phone is connected to a Polycom HDX system or Polycom RealPresence

Group system, see Connecting Optional Video Components on page 1-13.

Connecting Microphones to a Single Phone Setup

You can attach up to two analog expansion microphones or three Polycom

Microphone Arrays to a single phone setup. You can daisy-chain two or three

Polycom Microphone Arrays. You cannot daisy-chain analog expansion

microphones.

To connect microphones to a single phone setup:

Connect the free end of a microphone cable to one of the microphone

connectors on your phone.

To attach two microphones, connect the free end of the other microphone

cable to the other microphone connector on your phone. (Or, if you are

attaching Polycom Microphone Arrays, you can daisy chain two

microphones to one microphone connector on your phone.)

If you want to attach three Polycom Microphone Arrays to your phone,

daisy chain three microphones to one microphone connector on your

phone. Or, daisy chain two microphones to one microphone connector,

and connect the third microphone to the other microphone connector on

your phone.

Connecting Microphones to a Two-Phone Setup

You can attach up to two analog expansion microphones or one Polycom

Microphone Array to a two-phone setup.

You can connect an analog expansion microphone to just one of the phones, or

connect an analog expansion microphone to each phone. You can connect a

Polycom Microphone Array to one phone only; you cannot connect a Polycom

Microphone Array to each phone.

Note

When you connect Polycom Microphone Arrays to your phone, you must connect

your phone to an AC power source and a Multi-Interface Module. For information on

connecting your phone using AC power and a Multi-Interface Module, see

Connecting Network and Power Sources on page 1-5.

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 10

To connect microphones to a two-phone setup:

Connect the free end of a microphone cable to the available microphone

connector on one of the phones. It does not matter which phone you attach

the microphone to.

If you want to attach two analog expansion microphones, connect the

other analog expansion microphone to the microphone connector on the

other phone.

The following figure shows a two-phone setup with two analog expansion

microphones (the maximum number you can attach for this setup).

Multi-Interface

Module

Console Interconnect Cable

12-foot

Network Cable (10-pin)

25-foot

Network Cable

Power Adapter

3.6m (12ft)

7.6m (25ft)

Setting Up Your Phone

1 - 11

Connecting Optional Auxiliary Audio Components

You can connect various auxiliary audio components, such as wireless (lapel)

microphones, speakers, and recording devices and computers (to record

phone calls) to your phone. You can also connect your conference phone to

audio from a mobile device or a computer calling application.

You connect audio components to one of the following connectors:

• 2.5mm audio connector on your conference phone—to hear audio from

mobile devices and computer calling applications.

To connect a mobile device to your conference phone, you require the

optional Mobile Device Cable. To connect a computer calling application

to your conference phone, you require the optional Computer Calling

Cable.

• Audio connectors and ports on the Multi-Interface Module—to connect

wireless (lapel) microphones, speakers, and recording devices and

computers (to record phone calls).

To connect audio components to the Multi-Interface Module, see your

system administrator.

After you connect an auxiliary audio component to the Multi-Interface

Module, you must enable the component. To enable the component, see

the User Guide for the Polycom SoundStation IP 7000 Phone, available from

the SoundStation IP 7000 Support page.

2.5mm Audio Connector on Phone

Your conference phone has a 2.5mm audio connector to connect to a mobile

device or to a computer calling application. You connect a mobile device or

computer calling application so you can use the conference phone speaker to

stream two-way audio from the mobile device or computer calling application

for hands-free conversations. When you connect mobile or computer audio to

your conference phone, all participants in a call or conference call (including

those connected through a mobile device or computer calling application) can

hear and speak to each other.

The 2.5mm audio connector is located on the right-side of your conference

phone, behind a door you flip open.

Note

You do not have to enable audio from a mobile device or from a computer calling

application. This audio is automatically enabled when you connect the

Mobile Phone Cable or the Computer Calling Cable to the 2.5mm audio connector

on your conference phone.

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 12

The following figure shows the 2.5mm audio connector on the side of the

conference phone. The 2.5mm audio connector has a mobile phone icon above

it.

To connect to audio from a mobile device:

Connect one end of the optional Mobile Device Cable to the headset jack

on your mobile device, and connect the other end to the 2.5mm audio

connector on your conference phone.

For information on using your conference phone with a mobile device

connection, see the User Guide for the Polycom SoundStation IP 7000 Phone,

available from the SoundStation IP 7000 Support page.

To connect to audio from a computer calling application:

Connect one end (the end with two connectors) of the Computer Calling

Cable (contained in the optional Computer Calling Kit) to the sound card

on your computer, and connect the other end to the 2.5mm audio

connector on your phone.

For information on using your phone with a computer calling application, see

the User Guide for the Polycom SoundStation IP 7000 Phone, available from the

SoundStation IP 7000 Support Web page.

Note

If your conference phone setup has two connected phones, you can attach the

Mobile Device Cable to either conference phone.

Setting Up Your Phone

1 - 13

Audio Connectors on Multi-Interface Module

The Multi-Interface Module has various connectors and ports to connect

wireless (lapel) microphones, speakers, and recording devices and computers

(to record phone calls). To attach and use audio components, see your system

administrator.

Connecting Optional Video Components

You can connect your phone to a Polycom HDX system or

Polycom RealPresence Group system so that your phone can conduct video

calls and conferences.

You can connect your phone to the following Polycom HDX systems:

• Polycom

HDX

4000 series

• Polycom

HDX

6000 HD

• Polycom

HDX

7000 series

• Polycom

HDX

8000 HD

• Polycom

HDX

9000 series

You can connect your phone to the following Polycom RealPresence Group

systems:

• Polycom

RealPresence

Group 300 system

• Polycom

RealPresence

Group 500 system

• Polycom

RealPresence

Group 700 system

For information on how to use your phone when it is connected to a

Polycom HDX system or Polycom RealPresence Group system, see the

User Guide for the Polycom SoundStation IP 7000 Phone, available from the

SoundStation IP 7000 Support page. For detailed information on how to use a

Polycom HDX system or Polycom RealPresence Group system, see the

Polycom HDX system or Polycom RealPresence Group system

documentation, which is available by navigating from the Video Support

page. For detailed information on software compatibility between

SoundStation IP 7000 phones and Polycom HDX systems and Polycom

RealPresence Group systems, see the Polycom UC Software Administrators’

Guide, available from the SoundStation IP 7000 Support page.

Before you set up your phone to connect to a Polycom HDX system or Polycom

RealPresence Group system, make sure you have the optional Video Kit

(containing a Polycom Microphone Array Cable). You use the Polycom

Microphone Array Cable to connect your phone to the Polycom HDX system

or Polycom RealPresence Group system.

Setup Guide for the Polycom SoundStation IP 7000 Phone

1 - 14

When you connect your phone to a Polycom HDX system or Polycom

RealPresence Group system, you do not need to connect your phone to a

power source (even if you want to attach Polycom Microphone Arrays to your

phone). The Polycom HDX system or Polycom RealPresence Group system

provides the power source.

To connect your phone to a Polycom HDX system or Polycom RealPresence Group

system:

1. (Optional, but highly recommended.) Connect your phone to the

network:

a Connect the 7.6m (25ft) Network Cable to the LAN jack on your

phone.

b Connect the other end of the 7.6m (25ft) Network Cable to an available

LAN port on the wall or hub/switch device port.

The following figure shows how to connect your phone to the

network.

Note

You can only connect a single-phone setup to the Polycom HDX system or Polycom

RealPresence Group system. That is, you cannot connect two phones together

(using the Console Interconnect Cable), and then connect the phones to a

Polycom HDX system or Polycom RealPresence Group system.

Note

If you want to use a Multi-Interface Module (to access auxiliary audio connectors),

follow the steps for Connecting Your Phone Using AC Power (One Phone, with

Multi-Interface Module) on page 1-5, and then go to step 2.

7.6m (25ft)

La pagina si sta caricando...

Polycom SoundStation IP 7000 Guida utente

Marca: Polycom

Modello: SoundStation IP 7000

Tipo: Guida utente

Questo manuale è adatto anche per

2200-19000-122

Scarica PDF

rapporto

in altre lingue

English: Polycom SoundStation IP 7000 User guide

Polycom SoundStation IP 7000 Guida utente

Questo manuale è adatto anche per

Polycom SoundStation IP 7000 Guida utente

in altre lingue

Documenti correlati

Altri documenti