Electrolux EWF549 Manuale utente

Marca: Electrolux

Modello: EWF549

Categoria: Lavatrici

Tipo: Manuale utente

Questo manuale è adatto anche per

EWF551

EW 549 F

EW 551 F

147 120 900

UserManualNukeCover.qxd 04/07/2005 13:20 Page 1

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly

important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of

the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use environmentally

friendly paper.

Dear customer,

Please read these operating instructions carefully

and pay particular attention to the safety notes

indicated in the first pages. We recommend that you

keep this instruction booklet for future reference and

pass it on to any future owners.

Washing hints 9

Sorting the laundry 9

Temperatures 9

Before loading the laundry 9

Maximum loads 9

Laundry weights 9

Removing stains 9

Detergents and additives 10

Operating sequence 11-12

International wash code symbols 13

Washing programmes 14-15

Maintenance 16

Door seal 16

Bodywork 16

Detergent dispenser drawer 16

Drain pump 16-17

Water inlet filter 17

Emergency emptying out 17

Frost precautions 17

Something not working? 18-19

Warnings 3

Disposal 4

Tips for environmental protection 4

Technical specifications 4

Installation 5

Unpacking 5

Positioning 5

Water inlet 5

Water drainage 6

Electrical connection 6

Your new washing machine 7

Description of the appliance 7

Detergent dispenser drawer 7

Use 8

Control panel 8

Controls 8

Contents

Transport damages

When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact the

Service Centre.

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 2

ENGLISH

Installation

• All internal packing must be removed before using

the appliance. Serious damage may be caused to

the machine or adjacent furniture if the protective

transit devices are not removed or are not

completely removed. Refer to the relevant

paragraph in the instruction book.

• Any electrical work required to install this

appliance must be carried out by a qualified

electrician.

• Any plumbing work required to install this

appliance must be carried out by a qualified

plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the

feet and the floor.

Use

• This appliance is designed for domestic use. It

must not be used for purposes other than those

for which it was designed.

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on each

garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

• Make sure that all pockets are empty. Objects

such as coins, safety pins, pins and screws can

cause extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing

garments in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

Warnings

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

laundry.

• Leave the porthole door slightly ajar when the

appliance is not in use. This preserves the door

seal and prevents the formation of musty smells.

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

• Always unplug the appliance and shut the water

tap after use.

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• During high temperature wash programmes the

door glass may get hot. Do not touch it!

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• Make sure that children or pets do not climb into

the drum.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

The following warnings are provided in the interests of overall safety. You must read them carefully

before installing or using the appliance.

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 3

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Machine

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• The machine works more economically if it is fully

loaded.

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

DIMENSIONS Height 85 cm

Width 60 cm

Depth 59 cm

MAXIMUM LOAD Cotton 5,5 kg

Synthetics 2,5 kg

Delicates 2,5 kg

Woollens 1 kg

SPIN SPEED 550 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz

TOTAL POWER ABSORBED 2200 W (EWF 551) / 450W (EWF 549)

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 500 kPa

Maximum 800 kPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 4

ENGLISH

Unpacking

All transit bolts and packing must be

removed before using the appliance.

You are advised to keep all transit devices so that they

can be refitted if the machine ever has to be transported

again.

1. Using a spanner, unscrew and remove the two

rear bottom screws. Slide out the two plastic pins.

Lay the machine on its back, taking care not to

squash the hoses. This can be avoided by placing

one of the corner packing pieces between the

machine and the floor.

2. Remove the polystyrene block(s) from the bottom of

the machine and release the two plastic bags.

3. Very carefully slide out the left polythene bag,

removing it towards the right and then

downwards.

4. Very carefully slide out the right polythene bag,

removing it towards the left and then upwards.

Remove the bottom cover placed into the drum of

your appliance, lay it’s hook as the arrow ’A’

indicates and push the top of the cover to seal it

closed

Important: You can find more detailed instructions

regarding the bottom cover assembling in it’s relative

bag.

5. Set the machine upright and remove the

remaining rear screw. Slide out the relevant pin.

6. Plug all the holes with the plugs which you will

find in the envelope containing the instruction

manual.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine

is not impeded by carpets, rugs etc. Check that

the machine does not touch the wall or cupboard

units. Carefully level by screwing the adjustable

feet in or out. Never place cardboard, wood or

similar materials under the machine to

compensate for any unevenness in the floor.

Water inlet

Connect the water inlet hose to a tap with 3/4” BSP

thread.

Use the hose supplied with the washing machine.

DO NOT USE OLD HOSES.

The other end of the inlet hose which connects to the

machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks.

P1051

Installation

P1123

P1126

P0255

P0001

P1127

P1128

P0002

P1088

P0021

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 5

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

Important!

Before connecting up the machine to new pipe work

or to pipe work that has not been used for some

time, run off a reasonable amount of water to flush

out any debris that may have collected in the pipes.

Water drainage

The end of the drain hose can be positioned in three

ways:

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

The drain hose must not be kinked.

For a correct functioning of the machine the

drain hose must remain hooked on the proper

support piece situated on the top part of the back

side of the appliance.

P1118

Electrical connection

This machine is designed to operate on a 220-230 V,

single-phase, 50 Hz supply.

Check that your domestic electrical installation can

take the maximum load required (2.05 kW), also

taking into account any other appliances in use.

Connect the machine to an earth socket.

The manufacturer declines any responsibility

for damage or injury through failure to

comply with the above safety precautions.

Should the appliance power supply cable need

to be replaced, this should be carried out

by our service centre.

Please ensure that when the appliance is

installed the power supply cable is easily

accessible.

P0022

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 6

ENGLISH

This new machine meets all modern needs for effective treatment of laundry with low water, energy and

detergent consumption.

• The temperature selector dial will allow you to choose the most suitable temperature for your laundry.

• The automatic cooling of the washing water from 95° to 60°C before draining will prevent old drain pipes

from being deformed and will reduce thermal shock to fabrics, helping to prevent creasing.

• The special wool programme with its new delicate wash system treats your woollens with extreme care.

• The unbalance control device ensures the machine is stable during the spin.

• The ECO valve allows total use of detergent and reduces water consumption so saving energy.

1. Detergent dispenser drawer

2. Programme chart

3. Control panel

4. Door handle

5. Drain pump

6. Adjustable feet

Detergent dispenser drawer

Pre-wash

Main wash

Fabric softener, starch

Your new washing machine

Description of the appliance

C0063

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 7

Use

Control panel

1. Detergent Dispenser Drawer

2. ”Start /Add Clothes” Button

After having selected the programme and the required options, press this button to start the machine. The

corresponding LED stops flashing and remains lit. To interrupt a programme which is running,

depress the Start/Add Clothes button, the corresponding LED starts to flash.To restart the programme from the

point at which it was interrupted, press the Start/Add clothes button again.

3. ”Quick Wash”

Pressing this button, will shorten the selected wash program. As an example, if this button is pushed, the

LED will light up and the program ‘Automatic’ will be reduced to approx. 60 min from 110 min.

4. Programme Selector Dial

The selector is dived into three sections

OFF, COLD for EWF 549 and OFF, HOT and COLD for EWF 551

This can be rotated in clockwise and anti clockwise direction.

At the end of the programme the selector dialmust be turned to position “O” to switch the machine off.

Attention! If during a wash programme, the selector dial is turned to another programme, the machine will not

perform the new selected programme.

In the EWF 551 for HOT programs the temperature is preset (Refer page 14).

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 8

ENGLISH

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

whites, coloured, synthetics, delicate, woollens.

Before loading the laundry

Never wash whites and coloured together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins).

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes. Remove

persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Treat curtains with special care. Remove hooks or tie

them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

programme charts.

General rules:

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Delicate fabrics and woollens: drum no more than

one third full.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe 1200 g

napkin 100 g

quilt cover 700 g

sheet 500 g

pillow case 200 g

tablecloth 250 g

towel 200 g

tea cloth 100 g

night dress 200 g

ladies’ briefs 100 g

man’s work shirt 600 g

man’s shirt 200 g

man’s pyjamas 500 g

blouse 100 g

men’s underpants 100 g

Removing stains

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Blood: Treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Oil based paint: Moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Dried grease stains: Moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Rust: Oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Mould stains: Treat with bleach, rinse well (whites

and fast coloureds only).

Grass: Soap lightly and treat with bleach (whites and

fast coloured only).

Ball point pen and glue: Moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

Lipstick: Moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

Red wine: Soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

residual marks with bleach.

Washing hints

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 9

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

All commonly available washing machine detergents

may be used in this appliance:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (60°C max)

and woollens,

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of fabric,

or special for woollens only.

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

If using concentrated powder or liquid detergents, a

programme without prewash must be selected. The

washing machine incorporates a recirculation system

which allows an optimal use of the concentrated

detergent.

Pour liquid detergent into the dispenser drawer

compartment marked just before starting the

programme.

Any fabric softener or starching additives must be

poured into the compartment marked before

starting the wash programme.

Follow the product manufacturer’s recommendations

on quantities to use and do not exceed the «MAX»

mark in the detergent dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Water hardness is classified in so-called “degrees” of

hardness. Information on hardness of the water in

your area can be obtained from the relevant water

supply company, or from your local authority.

Follow the product manufacturers’ instructions on

quantities to use.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 10

ENGLISH

Operating sequence

Before the first wash we recommend that you pour

2 litres of water into the main wash compartment

ECO valve. Then run the automatic cycle with the

machine empty, in order to remove any

manufacturing residue from the drum and tub.

Pour half a measure of detergent into the main

wash compartment and start up the machine.

1. Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

main wash compartment .

If you wish to carry out the pre-wash, pour detergent

into the appropriate compartment marked .

3. Measure out the additive

If required, pour fabric softener into the compartment

marked , without exceeding the «MAX» mark.

P0004

4. Select the desired programmes

Turn the programme selector dial to the desired

position.

The LED corresponding to the Start / Add clothes

button starts to flash.

5. Select the option “Quick Wash”

if required

The LED corresponding to the Quick Wash button

illuminates

6. Start the machine

Push the Start / Add clothes button and the

programme starts

The LED corresponding to the Start/ Add clothes

button illuminates

C0064

C0065

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 11

7. At the end of the programme

The machine stops automatically and the

Start/Add clothes button LED goes off.

If you have selected the Quick Wash button,

LED for the button will also go off.

Wait one or two minutes before opening the door

to give the electric locking mechanism time to

release it.

Remove the laundry.

Turn the drum by hand to make sure it is

completely empty, so as to avoid any forgotten

items being damaged in a subsequent wash

(e.g. shrinking) or their colour running into

a load of whites.

Turn the water tap off and unplug the

machineLeave the door open for the tub to dry.

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 12

ENGLISH

Energetic wash

Delicate wash

Bleaching

Ironing Hot iron

max 200°C

Warm iron

max 150°C

Lukewarm iron

max 110°C

Do not iron

Dry cleaning

Drying Flat On the line On clothes

hanger

Tumble dry Do not

tumble dry

high

temperature

low

temperature

Dry cleaning

in all solvents

Dry cleaning in

perchlorethylene,

petrol, pure alcohol,

R 111 & R 113

Dry cleaning

in petrol,

pure alcohol

and R 113

Do not dry clean

Bleach in cold water Delicate wash

Hand wash Do not

wash

at all

Max. wash

temperature

95°C

Max. wash

temperature

60°C

Max. wash

temperature

40°C

Max. wash

temperature

30°C

International wash code symbol

These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 13

EWF 551 - Hot Programmes

The temperature of each programme is pre defined and is set automatically

Depending upon the type of laundry and is as per the se

Note: Normal spin is 500 rpm. , gentle spin is 450 rpm. and max spin is 550 rpm.

Programme table

Programme Type of laundry

and degree of soil

Programme Programme

description

Possible

option

Houselhold, linens,

sheets, shirts, under

garments

Jeans, hand towels,

sheets, table clothe

Shirts, blouses,

easy to iron

Delicate,

for. e.g. curtains

Clothes labelled

“ Pure new wool,

non-shrink machine

washable”

& silk fabrics

Automatic

Jeans / Towels

Easy Iron

Delicate

Wool and silk

Wash 40°, 3 rinses,

normal spin

Pre-Wash 40°,

Wash 60°, 5 rinses,

maximum spin

Wash 40°, 3 rinses,

gentle spin

Wash 30°, 3 rinses,

gentle spin

Wash 30°, 3 rinses,

normal spin

Quick Wash

Fast coloured cottons

like towels, Non fast

colured clothes like

under garments, shirts.

Acrilic, viscose,

polyester, curtains

Shirt, blouses,

undergarments,

mixed fabrics

Colour cottons

Synthetics

Hand Wash

Rinse

Drain

Spin

Wash, 3 rinses,

normal spin

Wash, 3 rinses,

gentle spin

Wash, 3 rinses,

gentle spin

3 rinses, drain

normal spin

Drain

Normal spin

Quick Wash

EWF 551 - Cold Programmes

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 14

ENGLISH

Programme table

EWF 549

Note: Normal spin is 500 rpm. and gentle spin is 450 rpm.

Programme Type of laundry

and degree of soil

Programme Programme

description

Possible

option

Houselhold , linens,

sheets, shirts,

under garments

Shirts, table clothes,

undergarments

Delicates like

pillow covers,

curtains

Easy to iron,shirts,

blouses

Acrylic,viscose,

polyester,curtains

Clothes labelled

“ Pure new wool, non

shrink machine

washble”

& silk fabrics

Shirt, blouses,

undergarments,

mixed fabrics

Automatic

Daily cotton

Delicate colour

Easy iron

Synthetics

Wool and silk

Hand Wash

Softner

Rinse

Drain

Spin

Pre-Wash, wash,

5 rinses, normal spin

Wash , 3 rinses,

normal spin

Wash , 3 rinses,

normal spin

Wash , 3 rinses,

normal spin

Wash , 3 rinses,

gentle spin

Wash , 3 rinses,

normal spin

Wash , 3 rinses,

gentle spin

1 rinse, normal spin

3 rinses, drain normal

spin

Drain

Normal spin

Quick Wash

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 15

Detergent can also accumulate inside the drawer

recess: clean it with an old toothbrush. Refit the

drawer after cleaning.

4. Cleaing Drain Pump

The pump should be inspected regularly and

particularly if

• the machine does not empty and/or spin

• the machine makes an unusual noise during

draining due to objects such as safety pins, coins

etc. blocking the pump.

Proceed as follows:

• Disconnect the appliance.

• If necessary wait until the water has cooled down.

• Open the pump door.

• Place a container close to the pump to collect any

spillage.

• Release the emergency emptying hose, place it in

the container and remove its cap.

• When no more water comes out, unscrew the

pump and remove it. Always keep a rag nearby to

dry up spillage of water when removing the pump.

P1115

P1114

P0038

1.Cleaning the Door Seal

Check from time to time the door seal and eliminate

eventual possible objects that could be trapped in

the fold.

2.External Cleaning

Clean the outside of the machine with warm water

znd a detergent used to handwash dishes. Rinse

with clean water and dry with a soft cloth.

Important: do not use methylated spirits, solvents or

similar products to clean the bodywork.

3. Cleaning the Detergent Drawer

After a while, detergents and fabric softeners leave

deposits in the drawer.

Clean the drawer from time to time by rinsing it under

a running tap. To remove the drawer from the

machine, press the button in the rear left-hand

corner.

To facilitate cleaning, the top part of the additive

compartments can be removed.

P1050

Maintenance

C0066

C0067

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 16

ENGLISH

• Remove any objects from the pump impeller by

rotating it.

• Put the cap back on the emergency emptying hose

and place the latter back in its seat.

• Screw the pump fully in.

• Close the pump door.

5. Water inlet filter

If you notice that the machine is taking longer to fill,

check that the filter in the water inlet hose is not

blocked.

Turn off the water tap.

Unscrew the hose from the tap. Clean the filter with a

stiff brush. Screw the hose back onto the tap.

P1117

6. Emergency emptying out

If the water is not discharged, proceed as follows to

empty out the machine:

• pull out the plug from the power socket;

• close the water tap;

• if necessary, wait until the water has cooled down;

• open the the pump door;

• place a bowl on the floor and place the end of the

emergency emptying hose into the bowl. Remove

its cap. The water should drain by gravity into the

bowl. When the bowl is full, put the cap back on

the hose. Empty the bowl. Repeat the procedure

until water stops flowing out;

• clean the pump if necessary as previously

described;

• replace the emergency emptying hose in its seat

after having plugged it;

• screw the pump again and close the door.

7. Frost precautions

If the machine is installed in a place where the

temperature could drop below 0°C, proceed as

follows:

• Remove the plug from the socket.

• Close the water tap and unscrew the water inlet

hose from the tap.

• Place the end of the emergency emptying hose

and that of the inlet hose in a bowl placed on the

floor and let water drain out.

• Screw the water inlet hose back on and reposition

the emergency emptying hose after having put the

cap on again.

By doing this, any water remaining in the machine is

removed, avoiding the formation of ice and,

consequently, breakage of the affected parts.

When you use the machine again, make sure that

the ambient temperature is above 0°C.

Important!

Every time you drain the water through the

emergency emptying hose you must pour 2 litres of

water into the main wash compartment of the

detergent drawer and then run the drain programme.

This will activate the ECO valve avoiding that part of

the detergent remains unused at next washing.

P1090

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 17

• The machine does not start up:

Problem Possible cause

Something not working?

Problems which you can resolve yourself.

• The door is not firmly closed.

• The machine is not plugged in or there is no power

at the socket.

• The main fuse has blown.

• The programme selector dial is not positioned

correctly.

• The “Start / Add clothes” button has not been depressed.

• The machine does not fill:

• The water tap is closed.

• The inlet hose is squashed or kinked.

• The filter in the inlet hose is blocked.

• The door is not properly closed.

• The machine fills then empties

immediately:

• The end of the drain hose is too low. Refer to relevant

paragraph in “water drainage” section.

• The drain hose is squashed or kinked.

• The drain pump is clogged.

• There is water on the floor:

• Too much detergent or unsuitable detergent

(creates too much foam) has been used.

• Check whether there are any leaks from one of the

inlet hose fittings. It is not always easy to see this as

the water runs down the hose; check to see if it is

damp.

• The drain hose is damaged.

• The cap on the emergency emptying hose has not

been replaced after cleaning the filter.

• Unsatisfactory washing results:

• Too little detergent or unsuitable detergent has been

used.

• Stubborn stains have not been treated prior to

washing.

• The correct temperature was not selected.

• Excessive laundry load.

• The machine vibrates or is noisy:

• The transit bolts and packing have not been removed.

• The support feet have not been adjusted.

• The laundry is not evenly distributed in the drum.

• Maybe there is very little laundry in the drum.

• The door will not open:

• The programme is still running.

• The door lock has not been released.

• There is water in the drum.

• The machine does not empty

and/or does not spin:

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 18

ENGLISH

• Spinning starts late or the laundry

is not spun enough:

Problem Possible cause

• The electronic unbalance detection device has cut

in because the laundry is not evenly distributed in

the drum. The laundry is redistributed by reverse

rotation of the drum. This may happen several

times before the unbalance disappears and normal

spinning can resume. If, after few minutes, the

laundry is still not evenly distributed in the drum,

the machine will not spin. If at the end of the

programme the laundry is not spun enough,

redistribute the load manually and select the spin

programme.

If you are unable to identify or solve the problem,

contact our service centre. Before telephoning, make

a note of the model, serial number and purchase

date of your machine: the Service Centre will require

this information.

Water is not

visible in the machine. The machine,

which is the result of modern technology, runs

in a very economical way with low water

consumption. Performance is

nevertheless excellent

The machine makes an unusual

noise. The machine is fitted with

a commutator motor which improves

machineperformance.

Model No:................

Product No: ........................

Serial No: ........................

UserManualNukeEUFinal.OK.qxd 04/07/2005 12:53 Pagina 19

à¤Ã×èÍ§ËÁÒÂ¤Óàµ×Í¹ÃÙ»ÊÒÁàËÅÕèÂÁËÃ×Í¤Óàµ×Í¹Í×è¹ (¤Óàµ×Í¹!¢éÍ¤ÇÃÃÐÇÑ§!) à¹é¹¶Ö§¢éÍÁÙÅ·ÕèÁÕ¤ÇÒÁÊÓ¤Ñà»ç¹¾ÔàÈÉµèÍ¤ÇÒÁ»ÅÍ´ÀÑÂ¢Í§¤Ø³ áÅÐ¡ÒÃ·Ó§Ò¹·Õè¶Ù¡µéÍ§¢Í§à¤Ã×èÍ§