ESD CPCI-405 Manuale del proprietario

Tipo
Manuale del proprietario

Questo manuale è adatto anche per

CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 1 of 57
esd electronic system design gmbh
Vahrenwalder Str. 20730165 Hannover • Germany
http://www.esd.eu
Phone: +49 (0) 511 3 72 98-0 Fax: +49 (0) 511 3 72 98-68
CPCI-405
CompactPCI-Controller Board
with CAN and ETHERNET
Hardware Manual
to product: I.2306.04, I.2306.05, I.2306.07,
I.2306.08, I.2306.12, I.2306.47,
I.2306.49
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 2 of 57
N O T E
The information in this document has been carefully checked and is believed to be entirely reliable.
esd makes no warranty of any kind with regard to the material in this document, and assumes no
responsibility for any errors that may appear in this document. In particular descriptions and technical
data specified in this document may not be constituted to be guaranteed product features in any legal
sense.
esd reserves the right to make changes without notice to this, or any of its products, to improve
reliability, performance or design.
All rights to this documentation are reserved by esd. Distribution to third parties and reproduction of
this document in any form, whole or in part, are subject to esd’s written approval.
© 2015 esd electronics system design gmbh, Hannover
esd electronic system design gmbh
Vahrenwalder Str. 207
30165 Hannover
Germany
Phone: +49-511-372 98-0
Fax: +49-511-372 98-68
Internet: www.esd.eu
This manual contains important information and instructions on safe and efficient
handling of the CPCI-405. Carefully read this manual before commencing any work
and follow the instructions to avoid serious injury or death.
The manual is a product component, please retain it for future use.
Trademark Notices
CANopen® and CiA® are registered community trademarks of CAN in Automation e.V.
CompactPCI® is a registered trademark of the PCI Industrial Computers Manufacturers Group.
CompactFlash® is a registered trademark of the SanDisk Corporation in the United States.
All other trademarks, product names, company names or company logos used in this manual are
reserved by their respective owners.
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 3 of 57
Document file:
I:\Texte\Doku\MANUALS\CPCI\CPCI405\Englisch\CPCI-405_Hardware_en_35.wpd
Date of print: 2015-11-13
Serial Number: from BC882
Changes in the chapters
The changes in the document listed below affect changes in the hardware as well as changes in the
description of the facts, only.
Version Chapter Changes as compared with previous version
3.4
1.3.3 NVRAM specified
2.1 Table completed
3.1.2 Addresses inserted
3.2.1 Default settings corrected (Handshake: none)
3.3.1 Table completed
3.5
- Safety instructions revised
1.3.7 New chapter "CompactFlash Card Interface"
4.1.1 Note concerning cable type inserted
4.5 Note concerning cable type inserted
6., 7. Chapters updated
8. Declaration of Conformity updated
9. Chapter "Order Information" moved and revised
Technical details are subject to change without further notice.
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 4 of 57
Safety Instructions
When working with CPCI-405 modules follow the instructions below and read the manual carefully to
protect yourself and the CPCI-405 module from damage.
The device is a built-in component. It is essential to ensure that the device is mounted in a way that
cannot lead to endangering or injury of persons or damage to objects.
Do not use damaged or defective cables to connect the CPCI-405 and follow the CAN wiring hints in
chapter: "Correct Wiring of Electrically Isolated CAN Networks"
The device has to be securely installed in the control cabinet before commissioning.
Protect the CPCI-405 module from dust, moisture and steam.
Protect the CPCI-405 module from shocks and vibrations.
The CPCI-405 module may become warm during normal use. Always allow adequate ventilation around
the CPCI-405 module and use care when handling.
Do not operate the CPCI-405 module adjacent to heat sources and do not expose it to unnecessary
thermal radiation. Ensure an ambient temperature as specified in the technical data.
Do not use damaged or defective cables to connect the CPCI-405 module.
In case of damages to the device, which might affect safety, appropriate and immediate measures must be
taken, that exclude an endangerment of persons and domestic animals and property.
Current circuits which are connected to the device have to be sufficiently protected against hazardous
voltage (SELV according to EN 60950-1).
The CPCI-405 may only be driven by power supply current circuits, that are contact protected. A power
supply, that provides a safety extra-low voltage (SELV or PELV) according to EN 60950-1, complies
with this conditions.
DANGER
Hazardous Voltage - Risk of electric shock due to unintentional contact with uninsulated live
parts with high voltages inside of the system into which the CPCI-405 is to be integrated.
Disconnect all hazardous voltages (mains voltage) before opening the system.
NOTICE
Electrostatic discharge may cause damage to electronic devices. In order to avoid this please
discharge your personal static electricity before you touch the module.
Qualified Personal
This documentation is directed exclusively towards qualified personal in control and automation engineering.
The installation and commissioning of the product may only be carried out by qualified personal, which is
authorized to put devices, systems and electric circuits into operation according to the applicable national
standards of safety engineering.
Conformity
The CPCI-405 is an industrial product and meets the demands of the EU regulations and EMC standards printed
in the conformity declaration at the end of this manual.
Warning: In a residential, commercial or light industrial environment the CPCI-405 may cause radio
interferences in which case the user may be required to take adequate measures.
Data Safety
This device is equipped with an Ethernet or other interface which is suitable to establish a connection to data
networks. Depending on the software used on the device, these interfaces may allow attackers to compromise
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 5 of 57
normal function, get illegal access or cause damage.
esd does not take responsibility for any damage caused by the device if operated at any networks. It is the
responsibility of the device's user to take care that necessary safety precautions for the device's network interface
are in place.
Intended Use
The intended use of the CPCI-405 module is the operation as High Performance PowerPC™ with Ethernet and
CAN.
The esd guarantee does not cover damages which result from improper use, usage not in accordance with
regulations or disregard of safety instructions and warnings.
The CPCI-405 module is intended for installation in a CompactPCI-system only.
The operation of the CPCI-405 module in hazardous areas, or areas exposed to potentially explosive
materials is not permitted.
The operation of the CPCI-405 module for medical purposes is prohibited.
Service Note
The CPCI-405 module does not contain any parts that require maintenance by the user. Unauthorized
intervention in the device voids warranty claims.
Disposal
Devices which have become defective in the long run have to be disposed in an appropriate way or have to be
returned to the manufacturer for proper disposal. Please, make a contribution to environmental protection.
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 6 of 57
Contents
Page
1. Overview ....................................................................8
1.1 Description of the CPCI-405 Board ............................................8
1.2 PCB View with Connector Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3 Summary of Technical Data ................................................. 11
1.3.1 General Technical Data............................................... 11
1.3.2 CompactPCI Bus....................................................12
1.3.3 Microprocessor and Memory ..........................................12
1.3.4 Serial Interfaces.....................................................13
1.3.5 CAN-Interfaces .....................................................13
1.3.6 ETHERNET Interface................................................14
1.3.7 CompactFlash Card Interface ..........................................14
1.3.8 Software Support....................................................14
2. Front Panel View with LED-Display ............................................15
2.1 LEDs in the Front Panel ....................................................15
3.1 PowerPC Microcontroller PPC405GPr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1.1 General ...........................................................17
3.1.2 Address Assignment .................................................18
3.1.3 Interrupt Settings....................................................19
3.2 Serial Interface............................................................20
3.2.1 Default Setting .....................................................20
3.2.2 Configuration ......................................................20
3.2.3 Connecting the RS-232-Interface SER 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.4 Connecting the Serial Interface SER 1 with TTL-Level . . . . . . . . . . . . . . . . . . . . . . 21
3.3 Function of Coding Switch ..................................................22
3.3.1 Overview..........................................................22
3.3.2 Switching the Boot-Flash-EPROM via Coding Switch Bit 4 . . . . . . . . . . . . . . . . . . 22
3.4 CAN/DeviceNet Unit ......................................................23
3.4.1 General ...........................................................23
3.4.2 Interface Circuits....................................................24
4. Connector Assignment ........................................................25
4.1 Serial Interfaces ...........................................................25
4.1.1 SER 0: Assignment of the RJ12 Socket X700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1.2 SER 0: Connection Cable RJ12-DSUB9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.1.3 SER 0: DSUB-Socket when Using the Adapter Cable RJ12-DSUB9 . . . . . . . . . . . 27
4.1.4 SER 1: Assignment of the 6-pin Post Connector X710 . . . . . . . . . . . . . . . . . . . . . . 28
4.2 CAN-Bus Interface (X1000) .................................................29
4.3 CAN-TTL Signals (X1010)..................................................30
4.4 Option: DeviceNet-Adapter Boards ...........................................31
4.5 ETHERNET 10/100BASE-T Connection (X1200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.6 Debug Port X720..........................................................35
4.6.1 Signal Alignment of the 16-pole SMD-Strip and JTAG-Adapter (PCB-Rev. 1.x) . . 35
4.6.2 Signal Alignment of 8-pole SMD-Strip and JTAG-Adapter (from PCB-Rev. 2.x) . 36
5. Special Designs: CPCI-405 with CPCI-CAN-ISO11898 Add-On .....................37
5.1 CPCI-405-2 PowerPC Host with 8 HP Front Panel (I.2306.49) . . . . . . . . . . . . . . . . . . . . . 37
5.1.1 Front Panel view of CPCI-405-2 with Adapter Board and 8 HP Front Panel . . . . . 38
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 7 of 57
5.2 CPCI-405-A PCI-Adapter with 6 U Front Panel (I.2306.47) . . . . . . . . . . . . . . . . . . . . . . . . 39
5.2.1 Front Panel view of the CPCI-405-A PCI-Adapter with 6 U Front Panel . . . . . . . . 40
5.3 Serial Interface............................................................41
5.3.1 RS-232 Interface ....................................................41
5.3.2 RS-422 interface ....................................................41
5.3.3 RS-485 interface ....................................................42
5.3.4 Solder Bridges for the Configuration of the Serial Interface SER1 . . . . . . . . . . . . . 43
5.4 Connector Assignments of the Special Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.4.1 CAN-Interface CAN 1................................................44
5.4.2 SER1: Assignment of the RJ12 Socket P100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6. Correct Wiring of Electrically Isolated CAN Networks .............................46
6.1 Standards concerning CAN Wiring............................................46
6.2 Heavy Industrial Environment (Double Twisted Pair Cable) . . . . . . . . . . . . . . . . . . . . . . . . 47
6.2.1 General Rules ......................................................47
6.2.2 Device Cabling .....................................................48
6.2.3 Termination ........................................................48
6.3 Light Industrial Environment (Single Twisted Pair Cable) . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.3.1 General Rules ......................................................49
6.3.2 Cabling ........................................................50
6.3.3 Termination ........................................................50
6.4 Electrical Grounding .......................................................51
6.5 Bus Length...............................................................51
6.6 Examples for CAN Cables ..................................................52
6.6.1 Cable for Light Industrial Environment Applications (Two-Wire) . . . . . . . . . . . . . . 52
6.6.2 Cable for Heavy Industrial Environment Applications (Four-Wire) . . . . . . . . . . . . . 52
7. CAN-Bus Troubleshooting Guide ...............................................53
7.1 Termination ..............................................................53
7.2 Electrical Grounding .......................................................54
7.3 Short Circuit in CAN Wiring.................................................54
7.4 CAN_H/CAN_L Voltage ...................................................54
7.5 CAN Transceiver Resistance Test ............................................55
7.6 Support by esd ............................................................55
8. EU Declaration of Conformity .................................................56
9. Order Information ...........................................................57
Overview
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 8 of 57
1. Overview
1.1 Description of the CPCI-405 Board
Fig. 1.1.1: Block circuit diagram
The CPCI-405 is a CompactPCI board in Euro format. It is available as PCI-master CPU or as
intelligent slave board. Both options only differ in the configuration of the PowerPC 405GPr processor.
Apart from a powerful CPU the PowerPC 405GPr processor has got an SDRAM controller, a PCI-bus
interface, a controller for serial interfaces and an MII-interface which is here used to realize an
ETHERNET interface.
In addition to Flash EPROM and NVRAM as system memory, the memory of the CPCI-405 has got
up to 128 Mbyte SDRAM as working memory. Furthermore, the board has got a CompactFlash card
interface. The boards plugged in can be accessed by standard system drivers like an IDE-drive.
One of the two serial interfaces has been designed as an RS-232-interface. It can be accessed via an
RJ12-connector in the front panel. The second serial interface is accessible via a post connector on
board. The signals of this interface are of TTL-level.
The CAN-interface which can be accessed via the front panel, is controlled by an SJA1000-CAN-
controller. The interface corresponds to ISO11898, is electrically insulated and can be used for
transmission rates of up to 1 Mbit/s. The second CAN-interface has got an SJA1000-CAN-controller
as well.
Overview
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 9 of 57
The TTL-signals of both controllers are led to a post connector. Here, two adapter boards can be
connected via flat ribbon cables, realising the physical layer. The adapter boards are available with CAN
(ISO11898) or DeviceNet interfaces. Optionally the CPCI-405 together with the adapter board is
available in two special designs (page 37).
The ETHERNET interface is suitable for 10 Mbit/s and 100 Mbit/s networks. They are connected via
an RJ45 socket in the front panel.
The status of the board is shown by LEDs in the front panel.
Overview
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 10 of 57
1.2 PCB View with Connector Designations
Fig. 1.2.1: PCB view (diagram without front panel)
The connector pin assignments can be found on page 25 and the following.
Overview
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 11 of 57
1.3 Summary of Technical Data
1.3.1 General Technical Data
Ambient temperature 0...50 C
Humidity max. 90 %, non-condensing
Power supply
via CompactPCI-bus,
5 V ± 5% / 200 mA (from PCB-rev. 2.0 on)
and
3.3 V ± 5% / 800 mA (from PCB-rev. 2.0 on)
Connectors
X100 (132-pin post connector) - CompactPCI-board connector J1
X101 (132-pin post connector) - CompactPCI-board connector J2
X700 (6-pin RJ12-socket) - RS-232-interface (SER 0)
X710 (6-pin post connector) - serial interface with TTL-level (SER 1)
X720 (8-pin SMD socket) - debug interface
X1000 (9-pin DSUB-connector) - CAN 0 (ISO11898)
X1010 (10-pin post connector) - CAN 0 (TTL) + CAN 1 (TTL)
X1100 (50-pin CompactFlash board connector) - CompactFlash boards
X1200 (8-pin RJ45-socket) - ETHERNET Twisted Pair (IEEE 802.3)
Dimensions 100 mm x 160 mm
Weight 200 g
Table 1.3.1: General technical data
Overview
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 12 of 57
1.3.2 CompactPCI Bus
Host bus PCI-bus in accordance with PCI Local Bus Specification 2.2
PCI-data/address bus 32 bits
Controller PowerPC 405GPr
Interrupt interrupt signal A, B, C, D
Board dimension in accordance with PCI-Specification, Rev. 1.0
Connectors
Connector coding Universal Board, not keyed
(3,3 V or 5 V signalling voltage)
Table 1.3.2: CompactPCI Bus interface
1.3.3 Microprocessor and Memory
CPU PowerPC 405GPr / 266 MHz (default at board type I.2306.04) /
32 bit
(up to 400 MHz as an option)
NVRAM
32 K x 8 bits
NVRAM: Simtek STK14C88 (no battery required)
option:
RTC with NVRAM STM M48T35Y (internal battery)
Flash-EPROM up to 4 M x 16 bits
Serial EEPROM 1 Kbyte
SDRAM 16 M x 32 bits (64 Mbyte) (default at board type I.2306.04)
32 M x 32 bits (128 Mbyte) (optional)
CompactFlash slot
- for CompactFlash memory boards in accordance with
CompactFlash
TM
specification
- suitable for board design type I
- 3.3 V-power supply
- controlled in ‘True IDE’ mode
Table 1.3.3: Microprocessor and memory
Overview
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 13 of 57
1.3.4 Serial Interfaces
Number 2
Controller PowerPC 405GPr
Bit rate Microcontroller: 300 bit/s ... 115.200 bit/s
RS-232-Transceiver: max. 115.200 Kbit/s
Physical interface Serial 0: RS-232C
Serial 1: TTL-level signals
Connectors Serial 0: 6-pin RJ12-socket in front panel
Serial 1: 6-pin post connector on board
Table 1.3.4: Serial interfaces
1.3.5 CAN-Interfaces
Number 2
CAN-controller SJA1000
CAN-protocol CAN 2.0A/2.0B
Physical interface CAN 0: differential, connection in accordance with ISO 11898
CAN 1: TTL-level, connection together with CAN 0-TTL to 10-pin
post connector
Transmission rate 10 Kbit/s ... 1 Mbit/s
Bus termination has to be terminated externally
Connectors CAN 0: DSUB9-connector in front panel and 10-pin post connector
for adapter board X1010
CAN 1: 10-pin post connector for adapter board X1010
Adapter board - to be connected to 10-pin post connector X1010
- available with differential CAN-interface (ISO11898) or
DeviceNet interface (with Combicon socket)
Table 1.3.5: CAN-interfaces
Overview
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 14 of 57
1.3.6 ETHERNET Interface
Number 1
Bit rate 10 Mbit/s, 100 Mbit/s
Controller PowerPC405GPr
Physical interface Twisted Pair (IEEE 802.3) 10/100BASE-T
Electrical insulation via repeating coil
Connector 8-pin RJ45-socket in front panel
Table 1.3.6: ETHERNET interface
1.3.7 CompactFlash Card Interface
Information about Usage of CompactFlash® Cards!
A correct functionality of the CompactFlash interface can only be ensured by usage
of CompactFlash cards with guaranteed SSD-properties.
esd therefore recommends to use one of the listed SLC-cards:
- Western Digital SiliconDrive II (e.g. 4GB: SSDC04G-4600)
- Cactus CompactFlash 303 Series (e.g. 4GB: KC4GR-303)
- Swissbit C-320 (e.g. 4GB: SFCF4096H1BO2TO-C-D1-523-SMA)
Only with this CF-cards the correct function of the CF-card interface is ensured and
support for the devices is provided.
esd will evaluate more CF-cards and release them on success.
1.3.8 Software Support
The boot monitor U-Boot* is stored in the Flash memory. This makes it possible for the CPCI-405 to
boot with various operating systems from the network, the local Flash memory or the Compact Flash
memory.
The operating systems Linux and VxWorks are available with according drivers for the local interfaces.
Further operating systems are available on request.
Furthermore the CAN-transmission protocols CANopen and DeviceNet and a local WEB-server are
available.
*
LED-Display
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 15 of 57
2. Front Panel View with LED-Display
The module has got four LEDs in the front panel and another LED which can only be seen on the board
itself when the case is open.
2.1 LEDs in the Front Panel
Fig. 2.1.1: Position and colours of LEDs
LED-Display
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 16 of 57
Name Colour Meaning of LED when on
CAN green CAN-frames are being received or transmitted
The LED is hardwired. The LED cannnot be controlled through
software.
RUN green
local CPU is in RUN status
(LED lights at every access to the SDRAM, therefore the LED can be
blinking or permanently on in normal operation)
The LED is hardwired. The LED cannnot be controlled through
software.
USR green application-specific programmable function
The USR LED is controlled by the 405 GPr CPU’s GPIO24 signal.
Clear GPIO24 to turn on the USR LED or set GPIO24 to turn it off.
RCV green ETHERNET bit rate: 100 Mbit/s
The LED is hardwired. The LED cannnot be controlled through
software.
Link
Status green link status ETHERNET (link to server or hub detected)
Receive
Status yellow receive status ETHERNET (reception of ETHERNET-data packages)
Table 2.1.1: Display functions of LEDs
Description of Units
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 17 of 57
3. Description of Units
3.1 PowerPC Microcontroller PPC405GPr
3.1.1 General
The general functions of the PowerPC 405GPr will not be explained in this manual. The manual of the
microcontroller can be downloaded from the homepage of the manufacturer AMCC at:
Description of Units
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 18 of 57
3.1.2 Address Assignment
Start address
[HEX] End address
[HEX] Unit
SDRAM (max. 64 Mbyte)
PCI Core memory
Internal periphery:
UART0-register (see 405GP-Manual Table 3-6 , S. 3-9) *
UART1-register (see 405GP-Manual Table 3-7 , S. 3-10) *
IIC0-register (see 405GP-Manual Table 3-8 , S. 3-11)
OPB-arbiter register (see 405GP-Manual Table 3-9 , S. 3-12)
GPIO-controller register (see 405GP-Manual Table 3-10 , S. 3-13)
Ethernet register (see 405GP-Manual Table 3-11 , S. 3-14)
CAN-controller CAN 0
CAN-controller CAN 1
IDE/CompactFlash
NVRAM (or NVRAM with RTC)
Free: User Space (24 Kbyte)
NVRAM (or NVRAM with RTC)
Reserved: VxWorks and esd internal use (4 Kbyte)
NVRAM (or NVRAM with RTC)
Reserved: PPCBoot/U-Boot environment variables (4 Kbyte)
Option NVRAM with RTC
RTC: Register start address end address
FPGA internal registers
Flash-EPROM bank 0 (SST39VF160 )
Flash-EPROM bank 1 (SST39VF160 )
Table 3.1.1: Addresses
* The UARTS are 16550-compatible.
Description of Units
CPCI-405
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
Page 19 of 57
3.1.3 Interrupt Settings
Interrupt External IRQ Circuit Level Detection
IRQ 25 EXT IRQ 0 CAN0 low active, level sensitive
IRQ 26 EXT IRQ 1 CAN1 low active, level sensitive
IRQ 27 EXT IRQ 2 PCI-INT_A high active, level sensitive
IRQ 28 EXT IRQ 3 PCI-INT_B high active, level sensitive
IRQ 29 EXT IRQ 4 PCI-INT_C low active, level sensitive
IRQ 30 EXT IRQ 5 PCI-INT_D low active, level sensitive
IRQ 31 EXT IRQ 6 CompactFlash high active, level sensitive
Table 3.1.2: Interrupt Setting
All other interrupt sources are PowerPC405-internal. They are described in the PowerPC405-manual.
Description of Units
Hardware-Manual • Doc.-No.: I.2306.21 / Rev. 3.5
CPCI-405
Page 20 of 57
3.2 Serial Interface
3.2.1 Default Setting
The default setting for both serial interfaces is the following:
Bit rate: 9600 Baud
Data bits: 8
Parity: no
Stop bits: 1
Handshake: none
3.2.2 Configuration
The serial interfaces are controlled by the microcontroller PowerPC405GPr. The bit rate of the
interfaces can be configured. The serial controller integrated in the PowerPC405GPr and the RS-232
driver used for interface SER 0 support bit rates of up to 115.200 kbit/s.
The bit rate can be changed by means of software. The procedure to change the bit rate depends on the
operating system, it is therefore advisable to refer to the manual of the operating system.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57

ESD CPCI-405 Manuale del proprietario

Tipo
Manuale del proprietario
Questo manuale è adatto anche per

in altre lingue