IMG Stage Line LSX-1200SRGB Manuale utente

VERSION:SD 2.0

This manual contains important laser system safety and operation

information. Read and understand all instructions prior to powering on

laser unit the first time, to avoid laser eye injury and to avoid breaking

the law. Keep this manual in a safe place for future reference.

USER MANUAL

1

WARNING DATA

Lasers can be hazardous and have unique safety considerations.

Permanent eye injury and blindness is possible if lasers are used

incorrectly. Pay close attention to each safety REMARK and

WARNING statement in the user manual. Read all instructions

carefully BEFORE operating this device.

Attention!

Important!

Caution!

Laser!

Recycle

Indoor

Wastebin

LLocation

Indicates a skill or other useful information for special

situations.

Indicates important information, to protect people from laser

incident or damage

Prevent damage or injury from incorrect operation.

Laser safety warming labels.

To protect the environment, recycle packing material

wherever possible.

The projector is for indoor use only, IP20. Use only in dry

locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with

water or any other fluids, or metallic objects.

Don’t throw this product away just as general trash, please

dispose of this product following the abandon electronic

product regulation in your country.

The projector must be installed in a location with adequate

ventilation, at least 50cm (20inches) from adjacent surfaces.

Be sure that no ventilation slots are blocked.

USER MANUAL

2

LASER SAFETY WARNINGS

Caution Avoid direct eye contact with laser 了light. Never

intentionally expose your eyes or others to direct laser

radiation.

Caution This laser product can potentially cause instant eye

injury or blindness if laser light directly strikes the eyes.

Caution It is illegal and dangerous to shine this laser into

audience areas, where the audience or other personnel

could get direct laser beams or bright reflections into

their eyes.

Caution It is a US Federal offense to shine any laser at aircraft.

Caution There are no user serviceable parts inside the unit. Do

not open the housing or attempt any repairs yourself. In

the unlikely event your unit may require service, please

contact the dealer nearest to you..

Caution Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

NON-INTERLOCKED HOUSING WARNING

This unit contains high power laser devices internally. Do not open the laser

housing, due to potential exposure to unsafe levels of laser radiation. The

laser power levels accessible if the unit is opened can cause instant

blindness, skin burns and fires.

Potential laser injury hazard exists with this product! Read these

Instructions carefully, which include important information about

installation

,

safe use and service!

USER MANUAL

3

LASER SAFETY AND OPERATING INSTRUCTIONS

STOP AND READ ALL LASER SAFETY DATA

Laser light is different from any other light source witch you may be familiar. The

light from this product can potentially cause eyes injury if not set up and used

properly.

Laser light is thousands of times more concentrated than light from any other kind

of light source. This concentration of light power can cause instant eye injuries,

primarily by burning the retina (the light sensitive portion at the back of the eye).

Even if you can not feel “heat” from a laser beam, it can still potentially injure or

blind you or your audience. Even very small amounts of laser light are potentially

hazardous even at long distances. Laser eye injuries can happen quicker than

you can blink.

It is incorrect to think that because these laser entertainment products split the

laser into hundreds of beams or laser beam is scanned out in high speed, that an

individual laser beam is safe for eye exposure. This laser product uses dozens of

milliwatts of laser power (Class 4 levels internally). Many of the individual beams

are potentially hazardous to the eyes.

It is also incorrect to assume that because the laser light is moving, it is safe. This

is not true. Nor, do the laser beams always move. Since eye injuries can occur

instantly, it is critical to prevent the possibility of any direct eye exposure. In the

laser safety regulation, it is not legal to aim Class 4 lasers in areas which people

can get exposed. This is true even if it is aimed below people’s faces, such as on

a dance floor.

z Do not operate laser without first reading and understanding all safety and

technical data in this manual.

z Always set up and install all laser effects so that all laser light is at least 3

meters (9.8 feet) above the floor on which people can stand. See “Proper

Laser Set-up & Usage” section later in this manual.

USER MANUAL

4

z After set up, and prior to public use test laser to ensure proper function. Do not

use if any defect is detected. Do not use if laser emits only one or two laser

beams rather than dozens/hundreds, as this could indicate damage to the

diffraction grating optic, and could allow emission of higher laser levels.

z Do not point lasers at people or animals.

z Never look into the laser aperture or laser beams.

z Do not point lasers in areas in which people can potentially get exposed. such

as uncontrolled balconies, etc.

z Do not point lasers at highly reflective surfaces such as windows, mirrors and

shiny metal. Even laser reflections can be hazardous

z Never point a laser at aircraft, this is a federal offense.

z Never point un-terminated laser beams into the sky.

z Do not expose the output optic (aperture) to cleaning chemicals.

z Do not use laser if the laser appears to be emitting only one or two beams.

z Do not use laser if housing is damaged or open, or if optics appear damaged

in any way.

z Never open the laser housing. The high laser power levels inside of the

protective housing can start fires, burn skin and will cause instant eye injury.

z Never leave this device running unattended.

z The operation of a Class 4 laser show laser is only allowed if the show is

controlled by a skilled and well-trained operator familiar with the data included

in this manual..

z The legal requirements for using laser entertainment products vary from

country to country.The user is responsible for the legal requirements at the

location/country of use.

z Always use appropriate lighting safety cables when hanging lights and effects

overhead.

LASER EXPOSURE WARNING

LASER LIGHT

AROVID DIRECT EYE EXPOSURE

Further guidelines and safety programs for safe use of lasers can be found in the

ANSI Z136.1 Standard “For Safe Use of Lasers”, available from

“www.laserinstitute.org”. Many local governments, corporations, agencies,

military and others, require all lasers to be used under the guidelines of ANSI

Z136.1. Laser Display guidance can be obtained via the International Laser

Display Association, www.laserist.org.

USER MANUAL

5

LASER SAFETY LABEL REPRODUCTIONS

This is only one laser aperture

on this product. The label

Indicates the laser beam

output aperture

Caution – Class 4 LASER

RADIATION, WHEN OPEN,

AVOID EXPOSURE TO

BEAM

LASER EMISSION DATA

* As measured under IEC measurement conditions for classification.

Note: The laser diode is exposed to extreme conditions due to the

high output power and therefore only has a limited life. Like all

wear parts, the laser diode is not subject to any guarantee claims.

Laser Classification Class 4

Red Laser Medium LD GaAlAs 650nm, typical

Green Laser Medium DPSS Nd:YVO4, 532nm

Blue Laser Medium LD GeAs 450nm, typical

Beam Diameter <5mm at aperture

Pulse Data All pulses < 4Hz (>0.25sec)

Divergence (each beam) <2 mrad

Divergence (total light) <40 degrees

Cooling TEC & Fan Cooling

Scanning ILDA Standard: 30Kpps

USER MANUAL

6

LASER COMPLIANCE STATEMENT

This laser product complies with EN/IEC 60825-1 Ed 2,2007-03.

GENERAL SAFETY INSTRUCTIONS

Every person involved with installation and maintenance of this device have to

z Be qualified.

z Follow the instructions of this manual.

This device has left out premises in absolutely perfect condition. In order to

maintain this condition and to ensure a safe operation, it is necessary for the user

to follow the safety instructions and warning notes written in this manual.

Important! The manufacturer will not accept liability for any resulting

damages caused by the non-observance of this manual or any

unauthorized modification to the device.

z Please consider that damages caused by manual modifications to the devise

are not subject to warranty.

z Never let the power-cord come into contact with other cables! Handle the

power-cord and all connections with the mains with particular caution!

z Make sure that the available voltage is not higher than stated on the rear

panel.

z Always plug in the power plug least. Make sure that the power-switch is set to

off-position before you connect the device to the mains. The power-plug has

to be accessed after installing the device.

z Make sure that the power-cord is never crimped or damaged by sharp edges.

Check the device and the power-cord from time to time.

CAUTION! Be careful with your operations. With a high voltage

you can suffer a dangerous electric shock when

touching the wires!

USER MANUAL

7

z Always disconnect from the mains, when the devise is not in use or before

cleaning it. Only handle the power-cord by the plug. Never pull out the plug by

tugging the power-cord.

z It is essential to connect the yellow/green conductor to earth.

z The electric connection, repairs and servicing must be carried out by a

qualified employee.

z Do not switch the fixture on and off in short intervals as this would reduce the

laser diode life.

z For replacement, please use fuses of same type and rating only.

z If the device has been exposed to drastic temperature fluctuation, do not

switch it on immediately. The arising condensation water might damage your

device. Leave the device switched off until it has reached room temperature..

z Do not shake the device. Avoid brute force when installing or operating the

device.

z When choosing the installation-spot, please make sure that the device is not

exposed to extreme heat, moisture or dust. There should not be any cables

lying around. You endanger your own and the safety of others!

z The minimum distance between the fixture and surrounding walls must be

more than 50cm.

z Always fix the fixture with an appropriate safety-rope. Fix the safety-rope at

the safety-rope only.

z The ambient temperature must be between 10℃ to 40℃.

z Please use the original packaging if the device is to be transported.

z Please consider that unauthorized modifications on the device are forbidden

due to safety reasons!

CAUTION! Operate the device only after having familiarized with

its functions. Do not permit operation by persons not

qualified for operating the device. Most damages are the

result of unprofessional operation

CAUTION! If this device will be operated in any way different to the

one described in this manual, the product may suffer

dama

g

es and the warrant

y

word.

USER MANUAL

8

BEFORE OPERATION

Unpacking Instructions

CAUTION! Immediately upon receiving a fixture, carefully unpack the

carton, check the contents to ensure that all parts are present,

and have been received in good condition. Notify the shipper

immediately and retain packing material for inspection if any

parts appear damage from shipping or the package itself

shows signs of mishandling. Save the package and all packing

materials. In the event that a fixture must be returned to the

factory, it is important that the fixture be returned in the original

factory box and packing.

What is included

The carton or flight case contain following items:

Power Supply

To determine the power requirements for a particular fixture, see the label affixed

to the back plate of the fixture of refer to the fixture’s specifications chart. A

fixture’s listed current rating is its average current draw under normal conditions.

All fixtures must be powered directly off a switched circuit and cannot be run off a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch. Before applying power to a fixture,

NAME QTY

Laser Light 1 PCS

KEYs (for key switch) 2PCS

Power Cord 1 PCS

Interlock Connector 1 PCS

1G SD Card 1 PCS

20m DB25 ILDA Cable 1 PCS

USER MANUAL 1 PCS

Flight Case 1PCS

USER MANUAL

9

channel is used solely for a 0% to 100% switch. Before applying power to a fixture,

check that the source voltage matches the fixture’s requirement.

The unit is supplied with a power plug appropriate to its voltage and

destination. Should any other connections be required they must be

carried out with the following configuration.

DMX-512 connection between fixtures

The fixture is equipped with 2-pin XLR sockets for DMX input and output. The

sockets are wired in parallel. Only use a shielded twisted-pair cable designed for

3-pin XLR-plugs and connectors in order to connect the controller with the fixture

or one fixture with another.

Occupation of the XLR-connection

Caution: At the laser fixture, the DMX-cable has to terminated with a

terminator. Solder a 120 Ohm resistor between Signal (-) and

Signal (+) into a 3-pin XLR-plug and plug and plug it in the

DMX-output of the last fixture.

Cable(EU) Cable(US) Pin International

Brown Black Live L

Liht blue White Neutral N

Yellow/Green Green Earth

USER MANUAL

10

Building a serial DMX-chain

z If you are using the standard DMX-controllers, you can connect the

DMX-output of the controller directly with the DMX-input of the first fixture in

the DMX-chain. If you wish to connect DMX-controllers with other

XLR-outputs, you need to use adapter cables.

z Connect the DMX-output of the first fixture in the DMX-chain with the

DMX-input of the next fixture. Always connect output with the input of the next

fixture until all fixtures are connected.

z If you use a controller with 5 pins DMX connector, you need to use a 5 to 3

pins adpter

z At last fixture, the DMX cable has to be terminated with a terminator. Solder a

120 Ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3 pins

XLR-plug and plug it in the DMX-output of the last fixture.

z Connect the fixture together in a daisy chain by XLR plug cable from the

output of the fixture to the input of the next fixture. The cable cannot be

branched or split to a Y cable. DMX 512 is a very high speed signal.

Inadequate or damaged cables, soldered joints or corroded connectors can

easily distort the signal and shut down the system.

z The DXM output and input connectors are pass-through to maintain the DMX

circuit, when power is disconnected to the unit.

z Each fixture needs to have a DMX address to receive the data from the

controller. The DMX address number which could be read from rear panel of

each fixture is between 000~511.

z The end of the DMX 512 chain should be terminated to reduce signal errors.

USER MANUAL

11

Proper Laser Set Up & Usage

This fixture has been designed to be hung. It is recommended for safety purposes,

your lighting effect are properly mounted using a suitable hanging clamp and

safety cable. Items appropriate for safe and effective mounting are easily

sourced from your lighting vendor.

International laser safety regulations require that lasers must be operated in the

fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation

between the floor and the lowest laser light vertically. Additionally, 2.5 meters of

horizontal separation is required between laser light and audience or other public

spaces.

USER MANUAL

12

Rigging the Fixture

z The installation of the fixture has to be built and constructed in a way that it

can hold 10 times the weight for 1 hour without any harming deformation..

z The installation must always be secured with a secondary safety attachment,

e.g. an appropriate catch net. This secondary safety attachment must be

constructed in a way that no part of the installation can fall down if the main

attachment fails.

z Make sure the area below the installation place is free from unwanted persons

during rigging, de-rigging and servicing.

z The operator has to make sure that safety-relating and machine-technical

installations are approved by an expert before taking into operation for the first

time and after changes before taking into operation another time.

z The operator has to make sure that safety-relating and machine-technical

installations are approved by a skilled person once a year.

z The fixture should be installed in the position where persons cannot reach and

where persons may walk by or be seated.

CAUTION! Please consider the respective national norms during

the installation! The installation must only be carried out

b

y

an authorized em

p

lo

y

ee or dealers!

CAUTION! When installing the device, make sure there is no highly

in inflammable material (decoration articles, etc.) in

between a distance of min 0.5 meter.

USER MANUAL

13

PRODUCT OVERVIEW

z This device has left out premise in absolutely perfect condition. In order to

maintain this condition and to ensure safe operation, it is necessary for the

user to follow the safety instructions and warning notes written in this manual.

z The manufacturer will not accept liability for any resulting damages caused by

the non-observance of this manual or any unauthorized modification to the

device.

Features

z STABLE TE COOLED LASER DIODE (CNI)

z HIGH SPEED 30KHz SCANNER

z 2 x AUTO SHOW + 2 x MUSIC SHOW

z 128 ANIMATED GRAPHIC SHOW PATTERNS

z HUNDRES PREPROGRAMED BEAM EFFECT

z MULTIMODE REAL WAVE EFFECT

z PERFECT WHITE COLOR BALANCE

z LCD CONTROL MONITOR

z SMART PRESS BUTTON CONTROL PANEL

z AUTO SELF CHECKING SYSTEM

z AUTO, SOUND, DMX & ILDA

z 2 DMX MODES & 13DMX CHANNELS

z AUTO DETECTED ILDA SIGNAL INTERFACE

z EXACTLY 3D ADJUSTABL COLOR MIXER

z KEY SWITCH & INTERLOCK

z 100% LASER SAFETY REGULATION

z BEAM, WAVE, TEXT, ANIMATION, LOGO

USER MANUAL

14

Front Panel

NO NAME FUNCTION

1 POWER Main power indicated LED. Red is ON.

2 MUSIC Synchronize to detected music signal

3 Laser output Laser output aperture.

4 HANDING BAND Product handing band

5 HANGING

BRACKET with 2 knobs on both sides to fasten the unit

and a mounting hole to fix a mounting hook.

USER MANUAL

15

Rear Panel

NO NAME FUNCTION

6 Switch Switch on and off the power

7 Mains input With socket and integrated fuse holder

8 ILDA / Hardware Setting Music, ILDA, Patterns Setting

9 Urgent and safe switch Switch off the laser manually if error occurs

10 SD card Storage RAM SD MMC storage RAM (less than 2G)

11 Key switch Make sure the professional person use

12 Cooling fan Cooling and never cover this fan outlet

13 DMX output 3PIN Female XLR port，using for DMX

14 DMX input 3PIN Male XLR port, using for DMX

15 Safety eye Attach the safety cable

USER MANUAL

16

ILDA / Hardware Setting Panel

NO NAME FUNCTION

16 MUSIC Turn the knob to adjust the audio respond

sensitivity.

17 X SIZE The Size of X axis adjustment

18 Y SIZE The Size of Y axis adjustment

19 ILDA THROUGH Standard ILDA DB25 Output(through)

20 ILDA INPUT Standard ILDA DB25 Input

21 ILDA ILDA connection indicator LED. Red is

connection and green is disconnection.

22 R G B Laser beam output indicator LED.

23 MIC Microphone. Turn the knob to adjust the

sound activated sensitivity.

24 LCD control Panel Intelligent LCD control panel of the system

USER MANUAL

17

IMPORTANT

For your own safely and full laser safety

Regulation, we do strongly recommend

You to take this optional switch!

CONTROL & FUNCTION

z Regular breaks during operation are essential to maximize the life of this

device as it is not designed for continual use.

z Do not switch the unit on and off in short time intervals

z Always unplug the unit when it is not used for a longer time. Or before

replacing the bulb or start servicing.

z In the event of serious operation problems, stop using the fixture and contact

your dealer immediately.

Attention Laser Safety Scanner Board is included in the system.

The Laser light will be turned off when the scanned angle

is less than 1 degree.

Operating Mode

Attention Once after every power on laser, the VERSION and

MANUFACTURE INFORMATION will be shown in LCD

monitor of rear panel.

When laser is powered on, LCD monitor on rear panel shows the current

operating standalone mode or DMX address of DMX mode. With help of LCD

control panel, is very easy to set and change the operating mode of laser. After

every resetting and saved, the new mode information will be shown on LCD

monitor at next power on.

USER MANUAL

18

Mode Option, to choose the operating mode of laser.

Confirmation, to confirm the laser to show the present mode at the

next operation.

UP/DOWN, to change operating mode, parameter or DMX address.

OPERATION

USER MANUAL

19

AUTO SHOW 1

z Press FUNC to enter MODE OPTION

z Till to AUTO SHOW 1 shown on LCD monitor.

The laser is set at AUTO SHOW 1 standalone mode and it will play the

preprogrammed show until next setting is changed. AUTO SHOW 1 is fast

and hot show which is better for

DISCO.

z Press ENTER to confirm the laser to

show the present mode at the next

operation.

AUTO SHOW 2

z Press FUNC to enter MODE OPTION

z Till to AUTO SHOW 2 shown on LCD monitor.

The laser is set at AUTO SHOW 2 standalone mode and it will play the

preprogrammed show until next setting is changed. AUTO SHOW 2 is slow

and soft show which is better for

MUSIC BAR.

z Press ENTER to confirm the laser to

show the present mode at the next

operation.

MUSIC SHOW 1

z Press FUNC to enter MODE OPTION

z Till to MUSIC SHOW 1 shown on LCD

monitor.

The laser is set at MUSIC SHOW 1

standalone mode and it will play the

preprogrammed show until next setting is changed. MUSIC SHOW 1 is fast

and hot show which is better for DISCO.

z Press ENTER to confirm the laser to show the present mode at the next

operation.

La pagina sta caricando ...

IMG Stage Line LSX-1200SRGB Manuale utente

IMG Stage Line LSX-1200SRGB Manuale utente

in altre lingue

Documenti correlati

Altri documenti