Spektrum AR10100T Guida utente

Tipo
Guida utente
AR10100T User Guide
AR10100T Bedienungsanleitung
Guide de L’utilisateur - AR10100T
AR10100T Guidea Dell’utente
EN
2
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability
of property damage, collateral damage, and serious injury OR create a high
probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability
of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of
physical property damage AND a little or no possibility of injury.
NOTICE
All instructions, warranties and other collateral documents are subject to
change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit horizonhobby.com or towerhobbies.com and click on the
support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
WARNING: Read the ENTIRE instruction manual to become familiar
with the features of the product before operating. Failure to
operate the product correctly can result in damage to the product, personal
property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution
and common sense and requires some basic mechanical ability. Failure to
operate this Product in a safe and responsible manner could result in injury
or damage to the product or other property. This product is not intended for
use by children without direct adult supervision. Do not attempt disassembly,
use with Incompatible components or augment product in any way without
the approval of Horizon Hobby, LLC. This manual contains instructions for
safety, operation and maintenance. It is essential to read and follow all the
instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS. Always
purchase from a Horizon Hobby, LLC authorized dealer to ensure
authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all
support and warranty with regards, but not limited to, compatibility and
performance of counterfeit products or products claiming compatibility with
DSM or Spektrum technology.
NOTICE: This product is only intended for use with unmanned, hobby-grade,
remote-controlled vehicles. Horizon Hobby disclaims all liability outside of the
intended purpose and will not provide warranty service related thereto.
Age Recommendation: Not for children under 14 years. This is not a toy.
EN
3
AR10100T Telemetry Receiver
The Spektrum AR10100T receiver
is a full range telemetry receiver
featuring DSM® technology. It is
compatible with all Spektrum
aircraft radios that support DSM2®
and DSMX® technology.
Perform the failsafe setup for the
AR10100T receiver through a com-
patible Spektrum Transmitter with Forward Programming. The Spektrum PC
Programmer can be used for firmware updates.
SPECIFICATIONS AR10100T
Type DSM2/DSMX 10 CH Telemetry Receiver
Application Air
Channels 10
Receivers 1
Remote Receiver
(not included)
SRXL2 Optional Remote Receiver
(SPM9747, SPM4651T)
Modulation DSM2/DSMX
Data Flight Log
Compatible No
Telemetry Integrated
Bind Method Bind Button
Failsafe Yes
Band 2.4GHz
Dimensions (LxWxH) 55 x 30 x 15mm
Weight 0.6 oz (18g)
Input Voltage 3.5–9V
Resolution 2048
Antenna Length 155mm and 186mm
Connector Micro USB
Bind/SRXL2 Port
Voltage Sensor Port
XBUS Port
RPM Port
L-SRXL2 Port
B-SRXL2 Port
Temperature Port
Micro USB Connector
Bind Button
Servo Ports
Channels 1–10
EN
4
AR10100T Receiver Installation
For optimum RF link performance, mount the antennas for optimal signal
reception accounting for all possible aircraft attitudes and positions. Orient the
antennas perpendicular to each other; typically vertical and horizontal and at
different angles.
Optional SRXL2 Remote Receiver (not included): If using an optional SRXL2
remote receiver, apply double-sided foam tape and mount it perpendicular to
and at least 2 inches away from the main receiver’s antenna.
Airplanes with significant carbon fiber construction can create an RF shielding
effect, reducing range. The AR10100T is designed to overcome these critical RF
issues in carbon airplanes by outfitting the aircraft with two external antennas at
specific points that will ensure secure RF coverage from all angles of the aircraft.
The AR10100T incorporates two feeder antennas; one antenna is 6.10 inches
(155 mm) and the second antenna is 7.32 inches (186 mm). They are designed
to be easily mounted through the fuselage in carbon airplanes. Each feeder
antenna includes acoaxial portion and an exposed 31mm tip antenna. The last
31mm is the active portion of the antenna.
186mm31mm
155mm31mm
Smart Throttle
The AR10100T receiver throttle port includes Smart Throttle. When equipped
with Smart Throttle the normal servo connector delivers the throttle signal to
the ESC, plus the ESC can send telemetry data like voltage and current back to
the receiver. The AR10100T receiver throttle port will automatically detect when
a Smart Throttle compatible ESC is plugged in and the throttle port will begin to
operate in Smart Throttle mode.
ESCs with Smart Throttle and IC3® and IC5® connectors can also pass along
battery data from compatible Spektrum Smart batteries.
If a standard ESC or servo is plugged into the throttle port on the AR10100T
receiver, the throttle port will operate normally (PWM signal) like any conven-
tional RC system. The AR10100T receiver is compatible with the Spektrum
Avian line of ESCs for Smart Throttle.
For Smart Throttle to function you must have a Smart Throttle ESC paired with
a Smart Throttle telemetry receiver, and a Spektrum DSMX transmitter with
telemetry. An update for your transmitter may be required for Smart features.
Visit www.spektrumrc.com to register and update your transmitter.
EN
5
External Antennas
Full Carbon
Installing the Receiver
Install the receiver in the normal position recommended by the airplane’s
manufacturer. Double-sided tape or foam can be used to secure the receiver
in place.
TIP: The hard case can be removed to help the AR10100T fit into a slim,
carbon fuselage. It is recommended to cover the bare receiver in heat
shrink.
Mounting the Antennas
To install the antennas, drill two 1/16-inch holes in the desired antenna mount-
ing positions.
Slide the feeder antennas through the holes until the 31mm tip, and about
2mm of coaxial, completely exit the fuselage. Use adrop of CA or tape to fix
the antenna to the fuselage.
IMPORTANT: Ensure that the 31mm active portion of each antenna tip is
fully exposed.
TIP: Use the optional (sold separately) Antenna Exit Guides to safely mount
the antennas outside of the fuselage.
IMPORTANT: If the antenna is to be mounted internally (in the front of
a2.4GHz fuse), the coaxial can be taped into position. Ensure the 31mm tip
is located at least 2 inches from any significant metal or carbon structure.
Check that at least one
antenna will always be in
the RF visual line of sight
of the transmitter (e.g. not
blocked by carbon fiber
structures) in all attitudes.
This can easily be visualized
by having a helper stand
about 20 feet away and rotate the airplane in all attitudes, confirming that there
is a direct line between you and at least one receiver antenna that isn’t blocked
by carbon fiber structure.
EN
6
Transmitter and Receiver Binding
Using an AS3X® SAFE® receiver requires a Spektrum DSM2®/DSMX® com-
patible transmitter with forward programming.
Binding
The AR10100T receiver must be bound to your transmitter before it will oper-
ate. Binding is the process of teaching the receiver the specific code of the
transmitter so it will only connect to that specific transmitter. When new out of
the package, the AR10100T will automatically go into bind mode the first time
it is powered on.
1. Connect up to two
optional SRXL2 remote
receivers (SPM9747 or
SPM4651T) and any
telemetry sensors to the
main receiver.
2. Push and hold the bind
button on the receiver
while turning the receiver
on. Release the bind
button once the orange
LED starts to flash
continuously, indicating that the receiver is in bind mode.
TIP: It is still possible to use a bind plug in the BIND port if desired. This
can come in handy if the receiver needs to be mounted in a location that is
difficult to access, in which case a servo extension may be used for binding.
If using a bind plug, remove after binding to prevent the system from
entering bind mode the next time the power is turned on.
3. Put your transmitter in bind mode.
4. The bind process is complete when the orange LED on the receiver is solid.
Failsafe
In the unlikely event that the radio link is lost during use, the receiver will en-
able the selected failsafe mode. Smart Safe + Hold Last is the default setting
on the AR10100T. Preset Failsafe and SAFE Failsafe are only available through
forward programming.
SmartSafe + Hold Last
If loss of signal occurs, SmartSafe™ technology moves the throttle channel to
its preset failsafe position (low throttle) that was set during binding. All other
channels will hold their last position. When the receiver detects the signal from
the transmitter, normal aircraft operation resumes.
EN
7
Forward Programming
Verify your transmitter is updated your transmitter to the latest Spektrum Air-
Ware™ software to take advantage of Forward Programming. See your trans-
mitter manual for updating instructions.
In your transmitter menu select Forward Programming -> Settings ->
• Select Failsafe -> Select each channel and assign it to Preset or Hold
Last. When you select a different channel for Output, a new group of
settings appears.
Capture Failsafe Postions ->
Hold the control sticks in the desired failsafe positions and select Apply.
Channel selections must be individually set in Forward Programming to
apply the preset positions or each channel will default to Hold Last. The
value captured will be reflected in the position shown for each channel.
Initiate Receiver Bind Mode
Gives you the option of putting the receiver into Bind Mode from this menu.
Preset Failsafe
With preset failsafe, you can set the specific control surface positions you want
to use if the signal is lost. When the receiver detects the signal from the trans-
mitter, normal aircraft operation resumes.
Only available through Forward Programming
Testing Failsafe
Secure the aircraft on the ground and remove the propeller. Test Failsafe set-
tings by turning the transmitter RF output off and noting how the receiver drives
the control surfaces.
Receiver Power Only
If the receiver is turned when no transmitter signal is present, the throttle
channel will not have a control signal to avoid operating or arming the
electronic speed control.
All other channels have no output until the receiver has linked to the
transmitter.
EN
8
Receiver Power System Requirements
Inadequate power systems that are unable to provide the necessary minimum
voltage to the receiver during flight have become the number one cause of
in-flight failures. Some of the power system components that affect the ability
to properly deliver adequate power include:
Receiver battery pack (number of cells, capacity, cell type, state of charge)
The ESC’s capability to deliver current to the receiver in electric aircraft
The switch harness, battery leads, servo leads, regulators etc.
The AR10100T has a minimum operational voltage of 3.5 volts; it is highly
recommended the power system be tested per the guidelines below.
Recommended Power System Test Guidelines
If a questionable power system is being used (e.g. small or old battery, ESC
that may not have a BEC that will support high-current draw, etc.), it is recom-
mended that a voltmeter be used to perform the following tests.
View the receiver voltage during this test on your transmitters telemetry screen,
load the control surfaces (apply pressure with your hand) while monitoring the
voltage at the receiver. The voltage should remain above 4.8 volts even when
all servos are heavily loaded.
How QuickConnect Technology Works
When the receiver voltage drops below 3.5 volts, the system ceases to
operate.
When power is restored, the receiver immediately attempts to reconnect.
If the transmitter was left on, the system reconnects typically in about
4/100 of a second.
QuickConnect is designed to allow you to fly safely through most short duration
power interruptions, however, the root cause of these interruptions must be
corrected before the next flight to prevent a crash.
NOTICE: If a brownout occurs in flight it is vital that the cause of the
brownout be determined and corrected.
IMPORTANT: When using Y-harness or servo extensions with Spektrum
equipment, do not use reversing harnesses. Using reversing Y-harnesses
or servo extensions may cause servos to operate erratically or not function
at all.
EN
9
Flight Log
Flight Log data can help you optimize the control link for your aircraft. Flight
Log data is displayed on telemetry capable Spektrum transmitters.
Using the Flight Log
A - Fades on main receiver B - Fades on remote receiver
L - Fades on remote receiver R - Not available on AR10100T
F - Frame losses H - Holds
Fades
Represents the loss of one bit of information on one receiver. Fades are used
to evaluate the performance of each individual receiver. If any single receiver
displays higher fade values it should be inspected and the antenna reposi-
tioned to optimize the RF link.
Frame Loss
A frame loss occurs when one complete data packet is missed. A single
frame loss does not represent a loss of control, but frame losses should be
monitored. In the air it's normal to experience as many as 100 frame losses
per minute of flight. On the ground the number of frame losses will be higher
because the signal is hampered by earth and moisture.
Hold
A Hold occurs when 45 consecutive frame losses occur. This takes about one
second, and in this event the receiver moves the channel outputs to the failsafe
settings. If a hold ever occurs, it’s important to re-evaluate the system and
check every component. If your system displays a hold taking place, diagnose
the cause and resolve the issue before flying again.
It is normal to see a hold logged if you power OFF your transmitter and back ON.
IMPORTANT: The Spektrum Flight Log (SPM9540) is not compatible with
the AR10100T receiver.
EN
10
Range Testing
Before each flying session, and especially with a new model, it’s important to
perform a range check. All Spektrum aircraft transmitters incorporate a range
testing system, which reduces the output power to allow a range check.
1. With the model resting on the ground, stand approximately 100 feet (30
meters) away from the model.
2. Face the model with the transmitter in your normal flying position and put
your transmitter into range test mode.
3. You should have total control of the model in range test mode at 100 feet.
4. If control issues exist, call Horizon Product Support for further assistance.
Advanced Range Testing
The Standard Range Testing procedure is recommended for most sport aircraft.
For sophisticated aircraft that contain significant amounts of conductive materi-
als (e.g. turbine powered jets, scale aircraft with matalized finishes, aircraft with
carbon fuselages, etc.), the following advanced range check will confirm that
all receivers in the system are operating optimally as installed. This advanced
range check allows the RF performance of each receiver to be evaluated
independantly. A telemetry equipped Spektrum Transmitter is required for the
advanced range test.
1. Stand approximately 100 feet away from the model.
2. Face the model with the transmitter in your normal flying position and put
your transmitter into range test mode.
3. Have a helper position the model in various orientations (nose up, nose
down, nose toward the transmitter, nose away from the transmitter, etc.).
4. Observe the telemetry on your transmitter. Note any orientations that cause
higher fades or frame loss values. Perform this step for at least one minute.
5. Re-position any antennas related to higher fades as necessary.
6. Re-test to verify satisfactory results.
7. Repeat as neccesary.
After one minute, advanced testing should yield:
H − 0 holds
F – less than 10 frame losses
A, B, L – Fades will typically be less than 100. It is important to compare the
relative frame losses. If a particular receiver has a significantly higher frame
loss value (2 to 3X) then the test should be redone. If the same results occur,
move the offending receiver to a different location.
TIP: Use the fade values for A to investigate the telemetry link performance.
EN
11
Optional Accesories
SPMA3065 USB Programming Cable
Telemetry Sensors and Accesories
SPMA9571 DSMX/DSMR Telemetry Temperature Sensor
SPMA9574 Aircraft Telemetry Airspeed Indicator
SPMA9589 Aircraft Telemetry Altitude and Variometer Sensor
SPMA9569 Aircraft Telemetry RPM Sensor and Bracket
SPMA9558 Brushless RPM Sensor
SPMA9587 Aircraft Telemetry GPS Sensor
SPMA9556 Air Telemetry Flight Pack Voltage Sensor: EC3/IC3
SPMA9604 Aircraft Telemetry Receiver Battery Energy Sensor
SPMA9605* Aircraft Telemetry Flight Pack Batt Energy Sensor
SPMA9551 12" Aircraft Telemetry Extension
SPMA9552 24" Aircraft Telemetry Extension
*For use with electric power system batteries that are separate from the re-
ceiver battery(s).
Telemetry
The AR10100T features full range telemetry and will provide receiver battery
voltage, flight log data, and various and altitude data without any additional
sensors. The altitude and vertical speed (variometer) sensor (
SPMA9589) func-
tions are already integrated in the
AR10100T
.
Additional telemetry devices such
as voltage sensors can be connected to the volt port, a temperature sensor
can be added in the temp port, RPM sensor can be added in the RPM port, and
XBUS telemetry sensors can be connected through the XBUS connector. Every
XBUS telemetry device has two XBUS ports, and XBUS telemetry sensors can
be connected in a daisy chain in any order.
See www.spektrumrc.com for more information about telemetry accessories.
EN
12
Problem Possible Cause Solution
Aircraft
will not
respond to
throttle but
responds
to other
controls
Throttle not at idle and/or
throttle trim too high
Reset controls with throttle
stick and throttle trim at low-
est setting
Throttle servo travel is lower
than 100%
Make sure throttle servo travel
is 100% or greater
Throttle channel is reversed
(With battery disconnected
from aircraft) Reverse throttle
channel on transmitter
Motor disconnected from
ESC
Make sure motor is connected
to the ESC
Aircraft will
not Bind
(during
binding) to
transmitter
Transmitter too near aircraft
during binding process
Move powered transmitter a
few feet from aircraft, discon-
nect and reconnect flight bat-
tery to aircraft
Aircraft or transmitter is too
close to large metal object,
wireless source or another
transmitter
Move aircraft and transmitter
to another location and at-
tempt binding again
The bind plug is not in-
stalled correctly in the bind
port
Install bind plug in bind port
and bind the aircraft to the
transmitter
Flight battery/transmitter
battery charge is too low Replace/recharge batteries
Bind button not held long
enough during bind process
Power off and repeat bind
process
Troubleshooting Guide
EN
13
Problem Possible Cause Solution
Aircraft
will not
connect
(after
binding) to
transmitter
Transmitter too near aircraft
during connecting process
Move powered transmitter a
few feet from aircraft, discon-
nect and reconnect flight bat-
tery to aircraft
Aircraft or transmitter is too
close to large metal object,
wireless source or another
transmitter
Move aircraft and transmitter
to another location and
attempt connecting again
Bind plug left installed in
bind port
Rebind transmitter to the
aircraft and remove the bind
plug before cycling power
Aircraft bound to different
model memory
(ModelMatchTM radios only)
Select correct model memory
on transmitter
Flight battery/Transmitter
battery charge is too low Replace/recharge batteries
Transmitter may have been
bound to a different aircraft
using different DSM protocol
Bind aircraft to transmitter
Control
surface
does not
move
Control surface, control
horn, linkage or servo
damage
Replace or repair damaged
parts and adjust controls
Wire damaged or
connections loose
Do a check of wires and con-
nections, connect or replace
as needed
Transmitter is not bound
correctly or the incorrect
airplanes was selected
Re-bind or select correct air-
planes in transmitter
Flight battery charge is low Fully recharge flight battery
BEC (Battery Elimination Cir-
cuit) of the ESC is damaged Replace ESC
Troubleshooting Guide
EN
14
1-Year Limited Warranty
What this Warranty Covers—Horizon Hobby, LLC, (Horizon) warrants to the original
purchaser that the product purchased (the “Product”) will be free from defects in
materials and workmanship for a period of 1 year from the date of purchase.
What is Not Covered—This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence,
commercial use, or due to improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted service by anyone other
than a Horizon Hobby authorized service center, (v) Product not purchased from
an authorized Horizon dealer, (vi) Product not compliant with applicable technical
regulations, or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE
DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF
THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy—Horizon’s sole obligation and purchaser’s sole and
exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii)
replace, any Product determined by Horizon to be defective. Horizon reserves
the right to inspect any and all Product(s) involved in a warranty claim. Service or
replacement decisions are at the sole discretion of Horizon. Proof of purchase is
required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability—HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED
IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER
THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual
price of the Product on which liability is asserted. As Horizon has no control over
use, setup, final assembly, modification or misuse, no liability shall be assumed nor
accepted for any resulting damage or injury. By the act of use, setup or assembly, the
user accepts all resulting liability. If you as the purchaser or user are not prepared to
accept the liability associated with the use of the Product, purchaser is advised to return
the Product immediately in new and unused condition to the place of purchase.
Law—These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Horizon reserves the right to change or modify
this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services—Your local hobby store and/or place of
purchase cannot provide warranty support or service. Once assembly, setup or use
of the Product has been started, you must contact your local distributor or Horizon
directly. This will enable Horizon to better answer your questions and service you in
the event that you may need any assistance. For questions or assistance, please
EN
15
visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty and Service Contact
Information section to speak with a Product Support representative.
Inspection or Services—If this Product needs to be inspected or serviced and
is compliant in the country you live and use the Product in, please use the Horizon
Online Service Request submission process found on our website or call Horizon to
obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely
using a shipping carton. Please note that original boxes may be included, but are not
designed to withstand the rigors of shipping without additional protection. Ship via a
carrier that provides tracking and insurance for lost or damaged parcels, as Horizon
is not responsible for merchandise until it arrives and is accepted at our facility.
An Online Service Request is available at http://www.horizonhobby.com/content/
service-center_render-service-center. If you do not have internet access, please
contact Horizon Product Support to obtain a RMA number along with instructions
for submitting your product for service. When calling Horizon, you will be asked to
provide your complete name, street address, email address and phone number
where you can be reached during business hours. When sending product into
Horizon, please include your RMA number, a list of the included items, and a brief
summary of the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue
with a LiPo battery, please contact the appropriate Horizon Product
Support ofce.
Warranty Requirements—For Warranty consideration, you must include your
original sales receipt verifying the proof-of-purchase date. Provided warranty
conditions have been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service—Should your service not be covered by warranty, service
will be completed and payment will be required without notification or estimate of the
expense unless the expense exceeds 50% of the retail purchase cost. By submitting
the item for service you are agreeing to payment of the service without notification.
Service estimates are available upon request. You must include this request with your
item submitted for service. Non-warranty service estimates will be billed a minimum
of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts
money orders and cashier’s checks, as well as Visa, MasterCard, American Express,
and Discover cards. By submitting any item to Horizon for service, you are agreeing to
Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/
content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product
will not be serviced. Further, the sender will be responsible for
arranging return shipment of the un-serviced Product, through a
carrier of the sender’s choice and at the sender’s expense. Horizon
will hold non-compliant Product for a period of 60 days from
notication, after which it will be discarded.
10/2015
EN
16
Warranty and Service Contact Information
FCC Information
CONTAINS FCC ID: BRWSPMAR10100T
Supplier’s Declaration of Conformity
Spektrum AR10100T Telemetry Receiver (SPMAR10100T)
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
CAUTION: changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
2904 Research Rd., Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: HorizonHobby.com
Country of
Purchase Horizon Hobby Contact Information Address
United
States of
America
Horizon Service Center
(Repairs and Repair
Requests)
servicecenter.horizonhobby.
com/RequestForm/
2904 Research Rd
Champaign, Illinois,
61822 USA
Horizon Product
Support
(Product Technical
Assistance)
productsupport@
horizonhobby.com.
877-504-0233
Sales websales@horizonhobby.com
800-338-4639
EU
Horizon Technischer
Service service@horizonhobby.eu Hanskampring 9
D 22885
Barsbüttel,
Germany
Sales: Horizon Hobby
GmbH +49 (0) 4121 2655 100
EN
17
Compliance Information for the European Union
IC Information
CONTAINS IC: 6157A-SPMAR10100T
CAN ICES-3 (B)/NMB-3(B)
This device contains license-exempt transmitter(s)/receivers(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following 2 conditions:
This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
EU Compliance Statement:
Spektrum AR10100T Telemetry Receiver
(SPMAR10100T) Hereby, Horizon Hobby, LLC declares
that the device is in compliance with the following:
EU Radio Equipment Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address: https://www.horizonhobby.com/content/support-render-
compliance.
Wireless Frequency Range and Wireless Output Power:
2404 – 2476 MHz
18.99dBm
EU Manufacturer of Record:
Horizon Hobby, LLC
2904 Research Road
Champaign, IL 61822 USA
EU Importer of Record:
Horizon Hobby, GmbH
Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:
This appliance is labeled in accordance with European Directive
2012/19/EU concerning waste of electrical and electronic
equipment (WEEE). This label indicates that this product should
not be disposed of with household waste. It should be deposited
at an appropriate facility to enable recovery and recycling.
RF exposure statement
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator and any part of your body.
This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102.
It should be installed and operated with a minimum distance of 20cm between the radiator and any
part of your body.
Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de
la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm entre le
radiateur et toute partie de votre corps.
DE
18
Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf
unterschiedlich hohe Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:
WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich
wahrscheinlich Sachschäden, Kollateralschäden und schwere Verletzungen ODER
mit hoher Wahrscheinlichkeit oberflächliche Verletzungen.
ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich
wahrscheinlich Sachschäden UND die Gefahr von schweren Verletzungen.
HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich
möglicherweise Sachschäden UND eine geringe oder keine Gefahr von
Verletzungen ergeben.
HINWEIS
Allen Anweisungen, Garantien und anderen zugehörigen Dokumenten sind Ände-
rungen nach Ermessen von Horizon Hobby, LLC vorbehalten. Aktuelle Produktlite-
ratur fi nden Sie unter www.horizonhobby.com oder www.towerhobbies.com im
Support-Abschnitt für das Produkt.
Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.
WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung durch, um
sich vor der Inbetriebnahme mit den Funktionen des Produkts vertraut
zu machen. Wird dieses Produkt nicht korrekt betrieben, kann dies zu Schäden
am Produkt oder anderen Sachschäden und zu schweren Verletzungen führen.
Dies ist ein hochentwickeltes Hobbyprodukt und KEIN Spielzeug. Es muss mit
Vorsicht und gesundem Menschenverstand betrieben werden und erfordert ge-
wisse technische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere
und verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schä-
den am Produkt oder anderen Sachwerten führen. Dieses Produkt eignet sich
nicht für die Verwendung durch Kinder ohne direkte Überwachung eines Erwach-
senen. Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, LLC, das
Produkt zu zerlegen, es mit inkompatiblen Komponenten zu verwenden oder auf
jegliche Weise zu erweitern. Diese Bedienungsanleitung enthält Anweisungen für
Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau,
Einrichtung oder Verwendung alle Anweisungen und Warnhinweise im Handbuch
zu lesen und zu befolgen, damit das Produkt bestimmungsgemäß betrieben wer-
den kann und Schäden oder schwere Verletzungen vermieden werden.
WARNUNG ZU GEFÄLSCHTEN PRODUKTEN. Bitte kaufen Sie Ihre
Spektrum Produkte immer von einem autorisiertem Händler um si-
cherzu stellen, dass Sie ein authentisches hochqualitatives original Spektrum
Produkt gekauft haben. Horizon Hobby lehnt jede Unterstützung, Service oder
Garantieleistung von gefälschten Produkten oder Produkten ab die von sich in
Anspruch nehmen kompatibel mit Spektrum oder DSM zu sein.
HINWEIS: Dieses Produkt ist ausschließlich für die Verwendung in
unbemanten, ferngesteuerten Fahrzeugen und Fluggeräten im Hobbybereich
vorgese-hen. Horizon Hobby lehnt jede Haftung und Garantieleistung au-
sserhalb der vorgesehen Verwendung ab.
ERKLÄRUNG DER BEGRIFFE
DE
19
AR10100T Telemetrie Empfänger
Der Empfänger Spektrum AR10100T
ist ein kompletter Telemetrieempfän-
ger mit DSM-Technologie und er ist
mit allen Spektrum- Bordfunkgeräten
kompatibel, die DSM2- und DSMX-
Technologie unterstützen.
Sie können den AR10100T-Empfän-
ger über einen kompatiblen Spektrum-Sender mit Failsafe-Programmierung
einrichten. Der Spektrum PC Programmer kann für die Firmware-Aktualisierun-
gen verwendet werden.
AR10100T
Abmessungen DSM2/DSMX Telemetrieempfänger mit 10 Kanälen
Anwendungsbereich Air
Gewicht 10
Empfänger 1
Funkempfänger
(nicht enthalten)
SRXL2 Funkempfänger, optional
(SPM9747, SPM4651T)
Modulation DSM2/DSMX
Daten Flight-Log
kompatibel Nein
Telemetrie Integriert
Bindungsmethode Bindungsschalter
Failsafe Ja
Band 2.4GHz
Antennenlänge (LxWxH) 55 x 30 x 15mm
Gewicht 18g
Eingangsspannung 3.5–9V
Auflösung 2048
Antennenlänge 155mm und 186mm
Anschluss Micro USB
Bind/
SRXL2 Anschluss
Spannungssensoranschluss
XBUS-Anschluss
RPM-Anschluss
L-SRXL2-Anschluss
B-SRXL2-Anschluss
Temperatur-Anschluss
Micro-USB-Anschluss
Bindungsschalter
Servoanschlüsse
Kanäle 1–10
DE
20
Installation des Empfängers AR10100T
Um eine optimale Funkverbindung zu erreichen, montieren Sie die Antennen so,
dass sie unter Berücksichtigung aller möglichen Flugzeuglagen und -positionen
optimal Signale empfangen. Richten Sie die Antennen senkrecht zueinander
aus; in der Regel vertikal und horizontal und in verschiedenen Winkeln.
Optionale SRXL2 empfängers (nicht enthalten): Wenn Sie die optionale
SRXL2 empfängers verwenden, bringen Sie sie mit doppelseitigem Schaumkle-
beband senkrecht zur Antenne des Hauptempfängers und mindestens 2 Zoll
von dieser entfernt an.
Flugmodelle aus Carbonfaser Verbundstoffen oder mit sehr hohem Anteil an Car-
bonfaser können eine Abschirmung der Empfänger bewirken. Der AR10100T ist
speziell für solche Modelle entwickelt worden um eben dieses zu unterbinden. Der
AR10100T besitzt zwei sogenannte Feeder Antennen, die aus dem Rumpf geführt
werden können um die Empfangsqualität in optimaler Güte zu gewährleisten.
Der AR10100T verfügt über zwei Zuleitungsantennen; eine Antenne ist 155 mm (6,10
Zoll) und die zweite 186 mm (7,32 Zoll) groß. Sie sind so konstruiert, dass sie einfach
durch den Rumpf von Flugzeugen aus Carbonfasern montiert werden können. Jede
Zuleitungsantenne verfügt über einen koaxialen Abschnitt und eine freiliegende Anten-
nenspitze von 31mm. Die letzten 31mm sind der aktive Teil der Antenne.
186mm31mm
155mm31mm
SmartThrottle
Der Gasanschluss des Empfängers AR10100T bietet Smart Throttle. Bei der
Ausstattung mit Smart Throttle liefert der normale Servo-Anschluss das Gas-
signal an den Geschwindigkeitsregler, und der Geschwindigkeitsregler kann
Telemetriedaten wie Spannung und Stromstärke an den Empfänger zurücksen-
den. Der Gasanschluss des AR10100T-Empfängers erkennt automatisch, wenn
ein mit Smart Throttle kompatibler Geschwindigkeitsregler angeschlossen ist,
und schaltet in den Modus „Smart Throttle“.
Geschwindigkeitsregler mit Smart Throttle und Steckern der IC-Serie können
auch Akkudaten von kompatiblen Spektrum Smart-Akkus weitergeben.
Wird ein Standard-Geschwindigkeitsregler oder -Servo an den Gasanschluss des
AR10100T-Empfänger angeschlossen, so funktioniert der Gasanschluss normal
(PWM-Signal) wie jedes herkömmliche RC-System. Der AR10100T-Empfänger
ist kompatibel mit Spektrum Avian, einer Geschwindigkeitsregler-Serie für Smart
Throttle.
Damit Smart Throttle funktioniert, muss ein Smart-Throttle-Geschwindigkeitsregler
in Verbindung mit einem Smart-Throttle-Telemetrieempfänger und einen Spektrum
DSMX-Sender mit Telemetrie verwendet werden. Es kann eine Aktualisierung Ihres
Senders für die Smart-Funktionen erforderlich sein.
Siehe www.spektrumrc.com zum Registrieren und Aktualisieren Ihres Senders.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Spektrum AR10100T Guida utente

Tipo
Guida utente