DTS MINI BRICK Manuale utente

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS ................................................................................................................. 4

2- GENERAL WARNING .............................................................................................. 5

3- GENERAL WARRANTY CONDITIONS .................................................................... 5

4- TECHNICAL FEATURES ......................................................................................... 5

5- ACCESSORIES ........................................................................................................ 7

6- IMPORTANT SAFETY INFORMATION .................................................................... 8

6.1 Fire prevention...................................................................................................... 8

6.2 Prevention of electric shock .................................................................................. 8

6.3 Safety ................................................................................................................... 8

6.4 Level of protection against the penetration of solid and liquid objects .................. 8

6.5 Waste Electrical and Electronic Equipment (WEEE) directive .............................. 9

7- INSTALLATION ........................................................................................................ 9

7.1 Protection against liquids .................................................................................... 11

7.2 Movement ........................................................................................................... 11

7.3 Risk of fire .......................................................................................................... 11

7.4 Forced ventilation ............................................................................................... 12

7.5 Ambient temperature .......................................................................................... 12

8- INPUT / OUTPUT CONNECTIONS ......................................................................... 12

8.1 Internal fuse ........................................................................................................ 13

9- DMX SIGNAL CONNECTION .............................................................................. 14

9.1 DMX Addresses .................................................................................................. 15

9.2 Selecting the DMX address ................................................................................ 15

10- RDM FUNCTIONS ................................................................................................ 15

11- FIRMWARE UPDATING ....................................................................................... 16

12- DISPLAY FUNCTIONS ......................................................................................... 17

13- REC MODE ........................................................................................................... 20

14- ERROR MESSAGES ............................................................................................ 20

15- PERIODIC CLEANING ......................................................................................... 21

16- PERIODIC CONTROLS ........................................................................................ 21

17- HOLOGRAPHIC FILTER INSTALLATION ........................................................... 22

18- LENSES SET REPLACEMENT ............................................................................ 23

19- BARNDOOR INSTALLATION .............................................................................. 24

20- DMX PROTOCOL ................................................................................................. 25

4

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC

SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL INDICATES THE MAXIMUM

OPERATING AMBIENT TEMPERATURE

THIS SYMBOL MEANS “SUITABLE FOR

MOUNTING ON NORMALLY FLAMMABLE

SURFACES”

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE FROM THE ILLUMINATED OBJECTS

THIS SYMBOL MEANS “DO NOT STARE

AT THE OPERATING LIGHT SOURCE”

THIS SYMBOL INDICATES

PHOTOBIOLOGICAL SAFETY

THIS SYMBOL INDICATES THE EUROPEAN

COMMUNITY DIRECTIVE 2012/19/EC ON

WASTE ELECTRICAL AND ELECTRONIC

EQUIPMENT (WEEE)

!

5

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The unit is not for household use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

4- TECHNICAL FEATURES

OVERVIEW

The new BRICK is a high power, very compact, self-contained, IP65 LED Wash light.

BRICK is suitable for various purposes, offering a range of projection angles quickly

interchangeable (no tools required).

BRICK comes with an IP65 power cable plus 2 DMX cables with M / F XLR

connectors (all IP65), that make it perfect for temporary lighting applications, but also

for safe long-lasting installations.

Built with top quality components, BRICK gives you the best value for money by

efficient design and full production automation.

DTS product codes:

03.LDB100S11FC08 BRICK FC ULTRA-NARROW lenses Black finishing

Available on demand:

03.LDB100S11FC10 BRICK FC NARROW lenses Black finishing

03.LDB100S11FC25 BRICK FC MEDIUM Flood lenses Black finishing

03.LDB100S11FC40 BRICK FC WIDE Flood lenses Black finishing

LED Technology

24 x OSTAR STAGE “N” FULL RGBW LEDs

Optical group

8° projection angle

Range of quick-mounting holographic filters included: 20° / 40° / 60°x10° (no mounting

tools required)

Uniform projection on surfaces

Color generation

16 million colors

Wide palette of pure uniform Whites with variable linear color temperature (2700K –

8000K)

6

4- TECHNICAL FEATURES

Control

DMX 512 / RDM

10 DMX channels (Default)

4-digit 7-segment LED display + 4 soft keys

Protection

IP 65

Power supply

Built-in full-range PSU 100-240Vac 50-60 Hz

Consumption: 400VA Max

Connections

Power supply: 3 x 1 sq mm cable (1,5 m length)

DMX In/Out: 0,7 m cable with XLR 5 pins IP65 connector

Operating ambient temperature

-10° / 40°

Weight

10 Kg

Certifications

2014/35/UE ; 2014/30/UE

IEC 62471 ; IEC 695-2-1

EN 60598-1 ; EN 62471 ; EN 61347-2-13

EN 60598-2-17 ; EN 55015 EMC ; EN 61347-1

7

DIMENSIONS

5- ACCESSORIES

As standard

1 x Holographic filter 20° (code 0506A043.D11)

1 x Holographic filter 40° (code 0506A045.D11)

1 x Holographic filter 60°x10° (code 0506A092.D11)

1 x PowerCON TRUE1 female cable connector (code 0520P066)

1 x PowerCON TRUE1 male cable connector (code 0520P067)

1 x User’s Manual

Optional (on request)

- Bracket for ground installation (code 03.LA.213)

- Barndoor black finishing (code 03.LA.210)

- Permanent installation kit IP68: Power connector + 2 x DMX In/Out connectors (code

03.LA.214)

- Aliscaf clamp for tube diameter 50 mm (Max load 100 Kg) (code 0521A008)

(indicated for any kind of loads vertical / horizontal)

- Professional Quick trigger clamp (Max load 100 Kg) (code 0521A037) (not indicated

for horizontal load)

- “C” Clamp G60 (Max load 50 Kg) (code 0521A004) (not indicated for horizontal load)

- Safety cable 3 mm x 60 cm (Max load 60 Kg) (code 0521A010)

8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

-It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

-Minimum distance from the closest illuminable surface: 0,5 m.

-Replace any blown or damaged fuses only with those of identical value (T 5A 250V).

Refer to the wiring diagram if there is any doubt.

-Connect the unit to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any

function which involves touching the inside of the projector.

-The level of technology inherent in the BRICK requires the assistance of specialised

personnel for all servicing.

Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the unit.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Safety:

-Risk Group 2 product according to EN 62471.

CAUTION. Do not look directly into the light output. May be harmful to the eyes and

skin.

-Do not stare at the operating light source.

-The light source contained in this luminaire shall only be replaced by the

manufacturer or his service agent or a similar qualified person.

-The unit is not for household use and must be installed by a qualified electrician or

experienced person.

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the

failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 60°C. Never handle

the unit until at least 5 minutes have elapsed since the projector was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

6.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an outdoor appliance and its protection level against the

penetration of solid and liquid objects is IP65.

Suitable for wet locations.

!

9

6.5 Waste Electrical and Electronic equipment (WEEE) directive:

-The machine, accessories and packaging should be sorted for environmetal-friendly

Recycling.

For EC countries: according to the European Directive 2012/19/EC for Waste

Electrical and Electronic Equipment and its implementation into national right,

luminaires that are no longer usable must be collected separately and disposed of in

an environmentally correct manner.

7- INSTALLATION

The unit is suitable for wet locations.

For outdoor installation, BRICK is provided with a Display UV Protection.

BRICK may be either floor or ceiling mounted.

For floor mounting installation, a bracket with 4 rubber mounting feet (code 03.LA.213)

is available on demand.

10

7- INSTALLATION

For ceiling mounted installation, it is recommended the use of appropriate clamps to fix

the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hung it.

For outdoor application where BRICK needs to be installed vertically keep the

unit display towards the floor.

A permanent installation kit IP68 (code 03.LA.214) is available on demand.

ATTENTION:

A safety cable (code 0521A010) must be securely fixed to the unit’s mounting bracket

and to the support structure of the projector as shown in the picture.

Fixing clamps and safety cable are available on demand.

11

7.1 Protection against liquids

If IP65 protection is impaired for any reason, do not expose this product to external

atmospheric agents, because it could be damaged.

7.2 Movement

The projector has a maximum movement of 110° for Tilt.

7.3- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

It is permissible to place the unit on normally flammable materials surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

Minimum distance from the object being illuminated is 0,5 m.

12

7.4- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans.

These should, under no circumstances, be blocked or obstructed whilst the projector is

in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

7.5- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should not exceed 40°C.

8- INPUT / OUTPUT CONNECTIONS

13

8.1- Internal Fuse

Attention: the fuse replacement must be made by DTS personnel or

experienced person.

Wrong operations can damage the IP65 protection.

To access the internal fuse loose the 6 marked screws which fix the lateral cover on

display panel opposite side and remove the cover.

Use only replacement fuses rated T 5A 250V.

Paying attention to the gasket put in place the lateral cover and fix it with the 6 screws

previously removed.

14

9- DMX SIGNAL CONNECTION:

The unit operates using a digital DMX 512 signal.

Connection between the controller and the unit or between units must be carried out

using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the DMX connector chassis.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

unit to the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

If the display showing the DMX address flashes, then one of the following errors has

occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we

suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

15

9.1 DMX addresses

BRICK can be controlled with 10 DMX channels (Default).

In order to use the unit in 10 DMX channels mode (Default), set the following

addresses on the mixer:

Projector 1 A001

Projector 2 A011 If you want to select the next projector, just add “10”

Projector 3 A021

….. A….

projector 6 A051

9.2 Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more

quickly and you get a faster selection.

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

10- RDM FUNCTIONS

By using a RDM controller it is possible to set DMX address, DMX mode and other

parameters.

BRICK accepts the following RDM commands:

DEVICE_INFO

To read the following parameters:

 RDM protocol version

 Fixture model ID

 Fixture type

 Software version ID

 DMX channels

 DMX mode

 DMX address

 Total sub-fixtures

 Total sensors

IDENTIFY_DEVICE

All LED channels ON at max power to identify the

fixture

DMX_START_ADDRESS

To read / set the DMX address

SOFTWARE_VERSION_LABEL

Software version ID

SUPPORTED_PARAMETERS

List of all supported parameters

PARAMETER_DESCRIPTION

Description / details of Manufacturer Specific

parameter as “NO DMX ACTION”

DMX_PERSONALITY

To set the DMX mode

DMX_PERSONALITY_DESCRIPTION

Description / details of the DMX mode

DEVICE_MODEL_DESCRIPTION

Description / details of the Fixture model

MANUFACTURER_LABEL

Producer ID

SENSOR_DEFINITION, SENSOR VALUE

LED Temperature

16

10- RDM FUNCTIONS

RDM MANUFACTURER-SPECIFIC PIDs

NO DMX ACTION

To set the desired fixture’s behavior in case DMX

signal is missing or not available.

1 = Black-out

2 = CHPR (demo program steps 01..16 same as

menu “NDMX > CHPR”)

3 = All channels @ 100%

4 = CUSTOM (RGBW values set into the menus

“RED NO DMX”

“GREEN NO DMX”

“BLUE NO DMX”

“WHITE NO DMX”

5 = Keep last valid DMX signal

11- FIRMWARE UPDATING

To update the software version of the BRICK you need:

- DTS RED BOX interface (DTS Code 03.LA.008).

- USB-DMX Driver for the DTS RED BOX interface.

- “DTS Firmware Upgrade Utility v.2.02” program installed on PC.

- Latest firmware release available for BRICK unit.

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the DTS RED BOX USB-DMX driver on the PC you will use to update the unit

software.

2. Connect the DTS RED BOX interface to a spare USB port on the PC (be sure that

internal switch on DTS RED BOX is set to COM).

3. Connect the unit DMX input to the DTS RED BOX DMX output with a standard DMX

cable and turn ON the unit.

4. Send the new software version into the unit by using “DTS Firmware upgrade

Utility v.2.02” program. At the end of the procedure, the unit will reset.

17

12- DISPLAY FUNCTIONS

The BRICK display panel shows all the available control menus.

Using these options, it is possible to change the fixture’s setting.

Changing the DTS settings can vary the functions of the unit so that it does not

respond to the DMX 512 used to control it. Carefully follow the instructions below

before carrying out any variations or selections.

MENU

 To access the control menus in the display panel.

 To return to the previous level in the menu structure without

making a change.

 To exit the menus.

ENTER

 To select any required menu.

 To confirm any changes.

UP / DOWN

 To navigate the menus structure.

 To change any value.

Firmware release

1.00

18

MAIN MENU

LEVEL 1

LEVEL 2

LEVEL 3

FUNCTION









Display normal orientation for

floor mounting position

(Default)





Display inverted orientation for

suspended mounting position







Display always ON (Default)





Display goes OFF after 10

seconds







Allows to select 10 DMX

channels mode (Default)





Allows to select RGBW mode (4

DMX channels)









Allows to select the value of the

delay (in milliseconds) for Dimmer

channel reaction to DMX or

Program variation.

Off = Instant response to DMX

variation.

4 = 100 ms Smooth response to

DMX variation (Default)

20 = 500 ms Smooth response to

DMX variation.







Allows to select Quadratic

current for linear light output

(Default)





Allows to select Linear current

output







Allows to adjust the PWM

frequency value (Hz) in order to

reduce flickering in the process of

your camera recordings.

Default = 610 Hz







Allows to increase the LED’s

current from 1050mA to 1500mA

per channel

Default = ON



















Automatic mode without DMX

controller.

Chase with 16 steps previously

created in REC mode.

Speed time and wait time values

(in seconds) selectable by user

(Default = 10).

In Auto mode the unit do generate

DMX for slave units.















16 customizable Colour Macros.

RGBW values selectable by user

(Default = 255).



















Rainbow colours effect.

Speed time value (in seconds)

selectable by user (Default = 10).









16 Colour Macros as on DMX

channel 9 (MACRO COLOR).

Default = 01









12 White color temperature from

2700K to 8000K as on DMX

channel 8 (CCT).

Default = 2700K





Dimmer level selectable by user

as on DMX channel 6 (DIMMER)

Default = 255





Shutter level selectable by user

as on DMX channel 5

(SHUTTER)

Default = 15





Esc from automatic mode.

19

MAIN MENU

LEVEL 1

LEVEL 2

LEVEL 3

FUNCTION









In DMX Recorder mode it is

possible to create and store the

scenes of the CHPR menu by

using an external DMX controller.

The unit must be set to 10 DMX

channels mode.

Refer to “REC MODE” at page 20.

















Slave mode.

The unit is forced to DMX address

1 and 10 DMX channels mode

receiving signal from the unit set

in Auto mode.





Esc from slave mode







Allows to select the internal fans

speed.

Standard mode: High fans speed.

Silent mode: Low fans speed for a

very low noise operation.

Default = STD











No DMX action.

Keep last valid DMX signal

(Default)





Black-out







Chase with 16 steps previously

created in REC mode as per

AUTO > CHPR menu.

Speed time and wait time values

(in seconds) selectable by user

(Default = 10).

In Auto mode the unit do generate

DMX for slave units.











All channels @ 100%







Custom.

RGBW values selectable by user

(Default = 255).



















To restore default settings









LED temperature monitoring







Micro controller temperature

monitoring







Outputs 1 and 2 of LED Driver

board temperature monitoring







Output 3 and 4 of LED Driver

board temperature monitoring







Shows the total unit life time and

the RGBW LEDs life time























Software version

20

13- REC MODE

DMX Recorder mode

For the programming of ChPr by using a DMX controller, besides the 10 channels necessary

to control the unit a further 3 DMX channels are needed.

So that in RECORDER mode (via DMX) the unit will need 13 channels to be correctly

programmed.

The three new DMX channels are:

DMX channel 11 = SCENES channel

From 0-10 = no function (r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016)

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is

possible to record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing

the sequence as last scene.

With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that

the scene has been recorded). It is advised that you keep the REC channel set to 0 and to run

through the 255 only once you have decided to save the scene. If ChPr is not closed, by

indicating the last scene (Edit channel between 235-255), in playback mode all 16 scenes will

be played through even if not programmed.

14- ERROR MESSAGES

ERROR SHOWED ON DISPLAY

APPEARS WHEN



LED thermal sensor damaged (open or in

short circuit).

Unit immediately goes in black-out.



LED temperature detected over 100°C.

Unit immediately goes in black-out.



Micro controller thermal sensor damaged

(open or in short circuit).

Unit immediately goes in black-out.



Micro controller temperature detected over

100°C. Unit immediately goes in black-out.



Thermal sensor on outputs 1 and 2 of LED

Driver board damaged (open or in short

circuit).

Unit immediately goes in black-out.



Temperature detected over 100°C on

outputs 1 and 2 of LED Driver board. Unit

immediately goes in black-out.



Thermal sensor on outputs 3 and 4 of LED

Driver board damaged (open or in short

circuit).

Unit immediately goes in black-out.



Temperature detected over 100°C on

outputs 3 and 4 of LED Driver board. Unit

immediately goes in black-out.

La pagina sta caricando ...

DTS MINI BRICK Manuale utente

Questo manuale è adatto anche per

DTS MINI BRICK Manuale utente

in altre lingue

Documenti correlati

Altri documenti