Toshiba Printer B-480-QP SERIES Manuale utente

TEC Thermal Printer

B-480-QP SERIES

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

Gebruikershandleiding

Manuale Utente

LIST OF STANDARDS OF CONFORMITY

Manufacturer : TOSHIBA TEC Corporation

Address : 570 Ohito, Ohito-Cho, Tagata-Gun, Shizuoka-Ken, 410-2323

Japan

declares that following product

Product Name : Bar Code Printer

Model : B-48X-YY

Options : All

conforms to the following product specifications

Safety : EN 60 950

EMC : EN 55 022

EN 50082-1

Harmonics : EN 60 555-2

Voltage Fluctuations : EN 60 555-3

Supplementary Information

The product herewith complies with the requirements of the Low Voltage Directive 73/23/

EEC, and the EMC directive 89/336/EEC.

1) The product was tested in a typical set up TOSHIBA TEC personnel advocated.

2) The following technical documentation has been filed for review.

• Factory Inspection Certificate by TÜV

• Owner's Manual

• Schematic

• Certificates and Test Reports

by TOSHIBA TEC CORPORATION

570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN

TEC Thermal Printer

B-480-QP SERIES

Owner’s Manual

(i)

Safety Summary

ENGLISH VERSION EO1-33007

Safety Summary

Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions

necessary for safe handling are included in this manual. All warnings and cautions contained in this

manual should be read and understood before handling or maintaining the equipment.

Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified

using the procedures described in this manual, turn off the power, unplug the machine, then contact your

authorized TOSHIBA TEC representative for assistance.

Meanings of Each Symbol

This symbol indicates warning items (including cautions).

Specific warning contents are drawn inside the symbol.

(The symbol on the left indicates a general caution.)

This symbol indicates prohibited actions (prohibited items).

Specific prohibited contents are drawn inside or near the symbol.

(The symbol on the left indicates “no disassembling”.)

This symbol indicates actions which must be performed.

Specific instructions are drawn inside or near the symbol.

(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)

Do not use voltages other than the

voltage (AC) specified on the rating

plate, as this may cause fire or

electric shock.

Any other than the

specified AC voltage

is prohibited.

WARNING

This indicates that there is the risk of death or serious injury if the

machines are improperly handled contrary to this indication.

Prohibited

Do not plug in or unplug the power

cord plug with wet hands as this may

cause electric shock.

Do not place metal objects or

water-filled containers such as flower

vases, flower pots or mugs, etc. on

top of the machines. If metal objects

or spilled liquid enter the machines,

this may cause fire or electric

shock.

If the machines share the same

outlet with any other electrical

appliances which consume large

amounts of power, the voltage will

fluctuate widely each time these

appliances operate. Be sure to

provide an exclusive outlet for the

machine as this may cause the

machines to malfunction.

Do not insert or drop metal,

flammable or other foreign objects into

the machines through the ventilation

slits, as this may cause fire or electric

shock.

Prohibited

Do not scratch, damage or modify

the power cords. Also, do not place

heavy objects on, pull on, or exces-

sively bend the cords, as this may

cause fire or electrical shock.

Prohibited

Continued use of the machines in an

abnormal condition such as when the

machines are producing smoke or

strange smells may cause fire or elec-

tric shock. In these cases, immedi-

ately turn off the power switches and

disconnect the power cord plugs from

the outlet. Then, contact your author-

ized TOSHIBA TEC representative for

assistance.

Disconnect

the plug.

If the machines are dropped or their

cabinets damaged, first turn off the

power switches and disconnect the

power cord plugs from the outlet, and

then contact your authorized

TOSHIBA TEC representative for

assistance. Continued use of the

machine in that condition may cause

fire or electric shock.

Disconnect

the plug.

(ii)

Safety Summary

ENGLISH VERSION EO1-33007

CAUTION

This indicates that there is the risk of personal Injury or damage to

objects if the machines are improperly handled contrary to this indication.

If foreign objects (metal fragments,

water, liquids) enter the machines,

first turn off the power switches and

disconnect the power cord plugs from

the outlet, and then contact your

authorized TOSHIBA TEC repre-

sentative for assistance. Continued

use of the machine in that condition

may cause fire or electric shock.

Disconnect

the plug.

Do not remove covers, repair or

modify the machine by yourself. You

may be injured by high voltage, very

hot parts or sharp edges inside the

machine.

No disassem-

bling.

Ensure that the equipment is

properly grounded. Extension cables

should also be grounded. Fire or

electric shock could occur on

improperly grounded equipment.

Connect a

grounding

wire.

When unplugging the power cords,

be sure to hold and pull on the plug

portion. Pulling on the cord portion

may cut or expose the internal wires

and cause fire or electric shock.

Disconnect

the plug.

Precautions

The following precautions will help to ensure that this machine will continue to function correctly.

• Try to avoid locations that have the following adverse conditions:

* Temperatures out of the specification * Direct sunlight * High humidity

* Shared power source * Excessive vibration * Dust/Gas

• The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild

detergent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic

covers.

• USE ONLY TOSHIBA TEC SPECIFIED paper and ribbons.

• DO NOT STORE the paper or ribbons where they might be exposed to direct sunlight, high tem-

peratures, high humidity, dust, or gas.

• Ensure the printer is operated on a level surface.

• Any data stored in the memory of the printer could be lost during a printer fault.

• Try to avoid using this equipment on the same power supply as high voltage equipment or equip-

ment likely to cause mains interference.

• Unplug the machine whenever you are working inside it or cleaning it.

• Keep your work environment static free.

• Do not place heavy objects on top of the machines, as these items may become unbalanced and fall

causing injury.

• Do not block the ventilation slits of the machines, as this will cause heat to build up inside the

machines and may cause fire.

• Do not lean against the machine. It may fall on you and could cause injury.

• Care must be taken not to injure yourself with the printer paper cutter.

• Unplug the machine when it is not used for a long period of time.

Request Regarding Maintenance

• Utilize our maintenance services.

After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance

once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the

machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid

rainy seasons.

• Our preventive maintenance service performs the periodic checks and other work required to

maintain the quality and performance of the machines, preventing accidents beforehand.

For details, please consult your authorized TOSHIBA TEC representative for assistance.

• Using insecticides and other chemicals

Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or

other parts to deteriorate or cause the paint to peel.

ENGLISH VERSION EO1-33007

CAUTION:

1. This manual may not be copied in whole or in part without prior written permission of

TOSHIBA TEC.

2. The contents of this manual may be changed without notification.

3. Please refer to your local Authorized Service representative with regard to any queries you

may have in this manual.

TABLE OF CONTENTS

Page

1. INTRODUCTION ............................................................................................E1- 1

1.1 Applicable Model ...................................................................................E1- 1

1.2 Accessories ...........................................................................................E1- 1

2. SPECIFICATIONS..........................................................................................E2- 1

2.1 Printer ....................................................................................................E2- 1

2.2 Options ..................................................................................................E2- 2

2.3 Ribbon ...................................................................................................E2- 2

2.4 Media.....................................................................................................E2- 3

3. OVERVIEW ....................................................................................................E3- 1

3.1 Front/Rear View.....................................................................................E3- 1

3.2 Operation Panel.....................................................................................E3- 1

4. INSTALLING THE PRINTER .........................................................................E4- 1

4.1 Connecting the Power Cord and Cables ...............................................E4- 1

4.2 Procedure for Fitting Fan Filter..............................................................E4- 1

5. LOADING THE MEDIA ..................................................................................E5- 1

6. LOADING THE RIBBON................................................................................E6- 1

7. INSERTING THE OPTIONAL PCMCIA CARD..............................................E7- 1

8. CARE/HANDLING OF THE MEDIA AND RIBBON.......................................E8- 1

9. GENERAL MAINTENANCE...........................................................................E9- 1

9.1 Cleaning ................................................................................................E9- 1

9.2 Covers and Panels ................................................................................E9- 2

9.3 Removing Jammed Paper .....................................................................E9- 2

9.4 Threshold Setting ..................................................................................E9- 4

10. TROUBLESHOOTING .................................................................................E10- 1

E1-1

1. INTRODUCTION

ENGLISH VERSION EO1-33007

1.1 Applicable Model

1. INTRODUCTION

Thank you for choosing the TEC B-480 series thermal/transfer printer. This high performance printer is

equipped with superior hardware including the specially developed (12 dots/mm, 304.8 dots/inch) near

edge print head which will allow very clear print at a maximum speed of 203.2 mm/sec. (8 inches/sec.).

The media supply is internal. Optional features include an automatic ribbon saver, a built-in rewinder/strip

mechanism and external media supply.

This manual contains general set-up and maintenance information and should be read carefully to help

gain maximum performance and life from your printer. For most queries please refer to this manual and

keep it safe for future reference.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

CAUTION

To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.

CAUTION

Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the

moving parts, push the switch in the "OFF" position to stop movement.

1.1 Applicable Model

• B-482-TS10-QP

Model name description

B - 4 8 2 - T S 1 0 - Q P

QP: European version

2: Thermal direct/Thermal transfer

Issue mode

S: Batch

Resolution

T: 12 dots/mm

Owner's Manual Power Cord

(EO1-33007)

Unpacking Procedure Fan Filter

(FMBB0036801)

1.2 Accessories

E2-1

2. SPECIFICATIONS

ENGLISH VERSION EO1-33007

2.1 Printer

2. SPECIFICATIONS

2.1 Printer

Supply voltage

Power consumption

Operating temperature range

Relative humidity

Print head

Printing methods

Print speeds

Maximum print width

Dispensing modes

Message display

Dimensions

Weight

Available bar code types

Fonts

Rotations

Standard interface

Optional interfaces

AC 220V ~ 240V +10%, -15%, 50Hz

1.13A, 128W maximum (standby: 250mA, 23W)

5°C ~ 40°C (41°F ~ 104°F)

25% ~ 85%RH (no condensation)

Thermal print head 12 dots per mm (304.8 dots per inch)

Thermal direct or Thermal transfer

76.2 mm/sec. (3 inch/sec.), 127 mm/sec. (5 inch/sec.),

203.2 mm/sec. (8 inch/sec.),

101.6 mm/sec. (4inch/sec.) ... Thermal direct only

104.0 mm (4.09 inches)

Batch (Continuous), Strip (On-demand) and Cut modes

(Both cut and strip modes are available only when their respective

modules are fitted.)

16 characters x 1 line

291 mm (width) x 460 mm (depth) x 308 mm (height)

17 kg (without media and ribbon)

JAN8, EAN8, JAN13, EAN13, UPC-A, UPC-B

EAN8, EAN13, UPC-A, UPC-E + 2digit

EAN8, EAN13, UPC-A, UPC-E + 5digit

NW-7

CODE39 (STANDARD)

CODE39 (FULL ASCII)

ITF

MSI

CODE93

CODE128

EAN128

Data Matrix

PDF417

QR Code

industrial 2 of 5

Customer Bar Code

POSTNET

RM4SCC (ROYAL MAIL 4STATE CUSTOMERCODE)

KIX CODE

Maxi Code

Micro PDF417

Times Roman (6 sizes), Helvetica (6 sizes), Presentation (1 size),

Letter Gothic (1 size), Prestige Elite (2 sizes), Courier (2 sizes),

OCR (2 types), Writable characters (2-byte character is available),

Outline font (4 type), Price font (3 types)

0°, 90°, 180°, 270°

Serial interface (RS-232C)

Parallel interface (Centronics)

Expansion I/O interface

PCMCIA card interface

B-482-TS10-QP

Model

Item

E2-2

2. SPECIFICATIONS

ENGLISH VERSION EO1-33007

2.2 Option

Option Name

Swing cutter module

Rotary cutter module

Peel off module

Fanfold paper guide

module

PCMCIA interface

board

Expansion I/O interface

board

Usage

A stop and cut swing cutter

Rotary cutter

This allows use of on-demand (peel-off) operation or to

rewind labels and backing paper together when using the

rewind guide plate. To purchase the strip module, please

inquire at your local distributor.

This is a paper guide exclusively used for fanfold paper.

Attaching it in place of the standard paper guide allows the

printer to print on fanfold paper.

This board enables the following PCMCIA cards to be used.

* LAN card: 3 COM EtherLink

®

III (recommended)

3 COM 3CCE589ET (recommended)

* ATA card: Conforming to PC card ATA standard

* Flash memory card:1MB and 4MB cards (See Page 7-1.)

Installing this board allows connection to external device.

Type

B-4205-QM

B-8204-QM

B-4905-H-QM

B-4905-FF-QM

B-8700-PC-QM

B-8700-IO-QM

Type

Width

Length

Outer diameter

Spool type

68 mm ~ 112 mm

600 m

ø90 mm (max.)

2.3 Ribbon

NOTES: 1. "On the fly issue" means that the printer can draw and

print without stopping between labels.

2. To ensure print quality and print head life use only

TOSHIBA TEC specified media and ribbons.

3. When using the cutter ensure that label length B plus

inter label gap length E exceeds 35 mm. (i.e. label

pitch should be greater that 35 mm.) (See Page 2-3.)

4. When rewinding the media onto the take-up spool in

batch mode, the max. outer roll diameter should be 180

mm.

5. Use of rough media for the ribbon saving issue may

cause ribbon smudges.

NOTE: To purchase the OPTIONAL KIT, please contact your authorized TOSHIBA TEC representative

or TOSHIBA TEC Head Quarter.

E2-3

2. SPECIFICATIONS

ENGLISH VERSION EO1-33007

2.4 Media

NOTES: 1. The media specification other than above are unchanged.

2. The label length specifications for use with both cutters are:

(*1) When issuing a label using the rotary cutter, printing at a speed of 3"/sec., label length should be:

91.0mm - (Gap length/2) or more

(*2) When issuing a label using the rotary cutter, printing at a speed of 4"/sec., label length should be:

95.0mm - (Gap length/2) or more

(*3) When issuing a label using the rotary cutter, printing at a speed of 5"/sec., label length should be:

99.0mm - (Gap length/2) or more

(*4) When issuing a label using the rotary cutter, printing at a speed of 8"/sec., label length should be:

110.0mm - (Gap length/2) or more

(*5) When issuing a label using the swing cutter, label length should be:

35.0mm - (Gap length/2)

I I

H

G

D

C

1

2

A

F

B

E

Stop

position

Cut

position

Label

Reference

coordinate

Reference

coordinate

Stop

position

Cut

position

Feed direction

Tag paper

Black Mark

(on reverse side)

Tag paper

Reference

coordinate

Reference

coordinate

F

Refer to the following

NOTE 2. Black Mark

(on reverse side)

2.4 Media

Fig. 2-1

Item

A : Span of one label/tag

Label dispensing mode

Rotary cutter

3"/sec.:30.0

4"/sec.:30.0

5"/sec.:30.0

8"/sec.:38.0

2730.0

50.8

112.0

47.8

109.0

20.0

2726.0

2.0

10.0

1.0

1361.0

104.0 0.2

2730.0

2724.0

Cut mode

[Unit: mm]

Swing cutter

Head-up is OFF Head-up is ON

3"/sec.:94.0 3"/sec.:38.0

4"/sec.:98.0 4"/sec.:38.0

5"/sec.:102.0 5"/sec.:38.0

8"/sec.:113.0 8"/sec.:38.0

3"/sec.:81.0(*1) 3"/sec.:25.0

4"/sec.:85.0(*2) 4"/sec.:25.0

5"/sec.:89.0(*3) 5"/sec.:25.0

8"/sec.:100.0(*4) 8"/sec.:25.0

Strip modeBatch mode

25.4

-

10.0Min.

Label

Max.

Min.

Max.

Min.

Max.

Min.

38.0

25.4

25.0 (*5)

-10.0

3"/sec.:28.0

4"/sec.:28.0

5"/sec.:28.0

8"/sec.:36.0

23.0-8.0

2730.0

-

2726.0

Tag

23.48.0

3"/sec.:79.0 3"/sec.:23.0

4"/sec.:83.0 4"/sec.:23.0

5"/sec.:87.0 5"/sec.:23.0

8"/sec.:98.0 8"/sec.:23.0

23.021.46.0

2728.0

6.0

2726.0

2.0

H : Effective print length

Min.

Label

Max.

Min.

Max.

Tag

I : Print speed up/slow down area

Maximum effective length for on the fly issue

Outer roll diameter

B : Label/tag length

C : Width including backing paper

Max.

Min.

D : Label width

Max.

Min.

E : Gap length

Max.

Min.

F : Black mark length (Tag paper)

Tag

Label

Thickness

Max.

Min.

G : Effective print width

E3-1

3. OVERVIEW

ENGLISH VERSION EO1-33007

3.1 Front/Rear View

3. OVERVIEW

3.1 Front/Rear View

3.2 Operation Panel

MESSAGE DISPLAY (LCD)

When power is turned on and it is ready to print, "ON LINE" is

displayed.

POWER LED (Green)

Lights when the power is turned on.

ON-LINE LED (Green)

1) Flashes when communicating with a host computer.

2) On while printing.

ERROR LED (Red)

Lights when a communication error occurs, when the media/

ribbon ends or the printer does not operate correctly.

FEED key

Feeds paper.

RESTART key

Resets the printer when paused or when an error occurs.

Used to set the threshold. (Refer to page 9-4)

PAUSE key

Pauses printing.

Message display shows "PAUSE" and an unprinted count.

Used to set the threshold. (Refer to page 9-4)

Fig. 3-2

Fig. 3-1

Front View Rear View

Top Cover

Supply Window

Message Display (LCD)

Media Outlet

Operation Panel

PCMCIA Card Slot (2 slots)

Expansion I/O

Interface Connector

(Option)

Power Switch

0: OFF

1: ON

AC Power Inlet

Serial Interface

Connector

(RS-232C)

Parallel I/F Connector

(Centronics)

E4-1

4. INSTALLING THE PRINTER

ENGLISH VERSION EO1-33007

4.1 Connecting the Power Cord and Cables

WARNING:

Turn the POWER SWITCH to OFF before connecting the power cord or cables.

Fig. 4-1

4. INSTALLING THE PRINTER

4.1 Connecting the Power Cord and Cables

4.2 Procedure for Fitting Fan Filter

Serial I/F Cable (RS-232C)

Fig. 4-2

Parallel I/F Cable (Centronics)

Power Cord

When installing the printer, it is important to ensure that the fan filter is attached before using the printer.

The filter comes in 2 parts:

(1) FILTER PAD

(2) FILTER RETAINER

To fit put the filter pad inside the filter retainer and simply press into place according to the diagram above,

ensuring connecting pins are aligned with connecting holes.

Snap on

Expansion I/O Cable (Option)

E5-1

5. LOADING THE MEDIA

ENGLISH VERSION EO1-33007

Fig. 5-1

NOTES: 1.When the head lever is turned to position

2

, the print head is raised.

2.When the head lever is turned to position

3

, the print head and the pinch roller are raised.

3.To allow printing the head lever must be set to position

1

. (This ensures that the print head

and the pinch roller are closed.)

3. Turn the locking ring counter clockwise and remove the supply holder from the supply shaft.

NOTE: Do not turn the force the locking ring too far counterclockwise or it may come off the supply holder.

5. LOADING THE MEDIA

The printer prints both labels and tags.

1. Turn off the power and open the top cover.

2. Turn the head lever to position 3, then release the ribbon shaft holder plate.

Fig. 5-2

WARNING:

1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn

into the moving parts, push the switch in the “OFF” position to stop movement.

2. To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.

Ribbon Shaft Holder Plate

Head Lever

Top Cover

Supply Holder

Supply Shaft

Locking Ring

E5-2

5. LOADING THE MEDIA

ENGLISH VERSION EO1-33007

5. LOADING THE MEDIA

4. Put the media on the supply shaft.

5. Pass the media around the damper, then pull the media towards the front of the printer.

6. Insert the ridge of the supply holder into the groove of the supply shaft until the media is fixed. Then turn

the locking ring clockwise to secure the supply holder. This will centre the media automatically.

NOTE: Do not over tighten the locking ring of the supply holder.

7. Insert the media into the paper holders of the media guide, adjust the media guides to the media width,

and tighten the locking screw.

8. Check that the media path through the printer is straight. The media should be centered under the print

head.

NOTE: When using the label rolled with labels facing outside, please remove the upper plates of both

paper holders using the following procedure. Failure to do this may cause a paper jam error.

If you have any questions, please contact your nearest TOSHIBA TEC service representative.

Fig. 5-3

Fig. 5-4

Media

Paper Holder

Locking Screw

Media Guide

Supply Holder

Paper Holder

Print Head

Media

Supply Holder

Supply Shaft

Damper

Groove Ridge

Projection

E5-3

5. LOADING THE MEDIA

ENGLISH VERSION EO1-33007

5. LOADING THE MEDIA

■ Removing the paper holders' upper plates from the media guide

1 Remove the two T-4x8 screws to detach the media guide from the printer.

2 Remove the SM-3x6 screw or the SM-3x8 screw to detach the paper holders' upper plates from

the media guide.

Fig. 5-5

Media Guide

Screw (T-4x8)

3 Attach the media guide back in position.

NOTE: Do not lose the removed upper plates because they are required when using the label rolled

with labels facing inside.

9. Set the black mark/feed gap sensor to the correct position by turning the adjusting knob. Turning the

knob right will move the sensor towards the center of the media while turning left will move it away from

the center of the media.

Fig. 5-6

(Right)

(Left)

Screw (SM-3x8)

Paper Holder

Screw (SM-3x6)

Paper Holder

E5-4

5. LOADING THE MEDIA

ENGLISH VERSION EO1-33007

5. LOADING THE MEDIA

■ An easy way to set the black mark sensor position

1 Pull the media about 500 mm out of the front of the printer, turn the media back on it's self and

feed it under the print head past the sensor so that the black mark can be seen from above.

2 Adjust the sensor position to that of the black mark (the upper hole indicates the position of the

black mark sensor).

NOTE: Make sure to set the sensor to detect the center of the black mark, otherwise a paper jam

error could occur.

■ Setting the feed gap sensor position

1 Adjust the sensor to detect on the gap (the lower hole indicates the position of the feed gap

sensor.)

Fig. 5-7

Black Mark

Black Mark Sensor

(Feed Gap Sensor)

Adjusting Knob

Media

Fig. 5-8

(Black Mark Sensor)

Backing Paper

Media

Adjusting Knob

Feed Gap Sensor

Media

E5-5

5. LOADING THE MEDIA

ENGLISH VERSION EO1-33007

5. LOADING THE MEDIA

10. The media is now loaded and the sensor position is set.

Batch type:

NOTE: Set the selection switch to the STANDARD/STRIP position. Improper setting can affect the print

quality.

Strip type:

1 Remove enough labels from the leading edge media to leave 500 mm of backing paper

exposed.

2 Wind the backing paper onto the take-up spool and fix in position with the take-up clip.

(Wind the paper counter clockwise around the spool as this is the direction it rotates.)

3 Rotate the take-up spool anti-clockwise a few times to take up any slack in the backing paper.

Fig. 5-9

NOTES: 1. The backing paper is easier to feed back to the take-up spool if the front plate is removed.

2. When fitting the tace-up clip the longer side of the clip should be fitted into the shallow groove

on the take-up spool.

3. Set the selection switch to the STANDARD/STRIP position.

Fig. 5-10

Media

Take-up Spool

Take-up Clip

Backing Paper

Black Screw

(HAA-0004001)

Front Plate

E5-6

5. LOADING THE MEDIA

ENGLISH VERSION EO1-33007

5. LOADING THE MEDIA

Cutter type: Where a cutter is fitted load the media as standard and feed it through the cutter module.

Swing cutter and rotary cutter are available as an option. They are used in the same way

regardless of different shapes. Now, how to load the media using the swing cutter will be

introduced.

NOTES: 1. Be sure to cut the backing paper of label. Cutting labels will cause the glue to stick to the cutter,

which may affect the cutter quality and shorten the life.

2. If a label winds onto the platen during cut issue, please contact your nearest TOSHIBA TEC

service representative.

3. For the cutter type, the selection switch can be set to either position.

Built-in rewinder type:

1 Remove two black screws and front plate.

2 Fit the rewinder guide plate to the strip shaft, then attach it with the sems screws.

Fig. 5-11

Rewinder Guide Plate

(FMBD0034501)

NOTES: Set the selection switch to the REWINDER position.

3 Follow the procedure for strip type.

4 Adjustment

If the label skews when using built-in rewinder unit, turn the adjustment knob of the rewinder

guide plate to correct the label feed. Clockwise turn moves the rewinder guide plate forward

and counterclockwise moves it backward.

* When labels skew to the right:

Loosen the SM-4x8 sems screw with a philips-head screw driver. Turn the adjustment knob

clockwise, and tighten the SM-4x8 screw when the rewinder guide plate is positioned

correctly.

* When labels skew to the left:

Loosen the SM-4x8 screw with a phillips-head screw driver. Turn the adjustment knob

counterclockwise, and tighten the SM-4x8 screw when the rewinder guide plate is posi-

tioned correctly.

Fig. 5-12

SM-4x6B Sems Screw

Tear-off Bar

SM-4x6B Sems Screw

Adjustment Knob

SM-4x8 Sems Screw

Media Outlet

Cutter Module

Media

E6-1

6. LOADING THE RIBBON

ENGLISH VERSION EO1-33007

Fig. 6-2

4. Reset the ribbon shaft holder plate by aligning it with the ribbon shaft.

5. Turn the head lever clockwise to lower the print head.

6. Close the top cover.

6. LOADING THE RIBBON

WARNING:

1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn

into the moving parts, push the switch in the “OFF” position to stop movement.

2. To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.

There are two types of media available for printing on, these are standard media and direct thermal media

(a chemically treated surface). DO NOT LOAD a ribbon when using a direct thermal media.

1. When using a narrow width ribbon, slide the ribbon stoppers along the shafts to a position where the

ribbon will be centered when it is fitted. When changing from a narrow width to a wider one rotate the

ribbon stoppers by 90°, push them back to the correct position and then rotate back to lock.

NOTE: When attaching the ribbon stoppers, fit them to the shafts with the pinchers facing into the printer.

Ribbon Stopper

Fig. 6-1

2. Leaving plenty of slack between the spools, fit the ribbon as shown below. When the ribbon is fitted it

must be positioned over the ribbon sensor.

3. Wind both shafts towards each other to tighten the ribbon.

Ribbon Sensor

Ribbon Shafts

Ribbon

E7-1

7. INSERTING THE OPTIONAL PCMCIA CARD

ENGLISH VERSION EO1-33007

7. INSERTING THE OPTIONAL PCMCIA CARD

1. Turn the power off.

2. Insert the PCMCIA card into the card slot at the rear of the printer.

3. Turn the power on.

NOTES: 1. Be sure to protect a PCMCIA card when not in use in the printer by putting it in its protective

cover.

2. Do not subject the card to any shocks or excessive forces.

3. Do not expose the card to extremes of heat by either storing in direct sunlight or close to a

heater.

4. Do not expose the card to excessive humidity by wiping it with a wet cloth or storing it in a damp

place.

5. Before inserting or removing the card, make sure that the power switch is turned off.

6. The following flash cards can be used. (The 1MB-card is read only and the 4MB card can read/

write.)

Fig. 7-1

PCMCIA Card

1

0

7. Install the LAN card into the slot (1).

Capacity

1M Byte

4M Byte

Maker

Maxell

Mitsubishi

Maxell

Centennial Technologies INC.

INTEL

Simple TECHNOLOGY

Mitsubishi

PC Card KING MAX

PC Card

Type

EF-1M-TB AA

MF81M1-GBDAT01

EF-4M-TB CC

EF-4M-TB DC

FL04M-15-11119-03

IMC004FLSA

STI-FL/4A

MF84M1-G7DAT01

FJN-004M6C

FJP-004M6R

Device code

D0H

88H

ADH

A2H

A0H

Maker code

1CH

B0H

04H

01H

89H

CAUTION:

To protect PCMCIA cards, discharge static electricity from your body by touching the printer rear

cover prior touching the PCMCIA cards.

WARNING!

Turn the power OFF when inserting or removing the PCMCIA card.

La pagina sta caricando ...

Toshiba Printer B-480-QP SERIES Manuale utente

Questo manuale è adatto anche per

Toshiba Printer B-480-QP SERIES Manuale utente

in altre lingue

Documenti correlati

Altri documenti