WisyCom MRK960 Manuale utente

Marca: WisyCom

Modello: MRK960

Tipo: Manuale utente

User Manual









Rev.06 (ref. FW 1.1.0.H)

Date: 20 January 2020

Pag. 2

MRK960 dual true diversity receiver



The MRK960 is a high performance microphone system suitable for broadcast and high professional applica-

on. Thanks to its exceponal selecvity and intermodulaon immunity, MRK960 is able to operate even in

the presence of very high DVTB-T transmier’s signals.

The extreme bandwidth agility of 370 MHz allows you to always nd & work on the best frequencies avail-

able. MRK960 is designed to be:

•• “easy & quick to use” thanks to automac setup funcons (i.e. frequencies, squelch), remote conguraon

ulies (USB/Ethernet), a display with intuive context menu navigaon.

•• “extremely exible”, with an incredible frequency agility of 370 MHz; more than one rack can be connected

together thru a simple USB cable to act a mul-channel receiver. Moreover the DSP board allows the units

to work with several digital audio outputs (i.e. AES/EBU, Ethersound, …), with mul-companding compat-

ibilies and other digital features.

•• “best in class performances”, thanks to the latest Wisycom technology the unit has extreme RF sensivity

and immunity and superb audio quality.

•• “a durable & upgradable investment”, thanks to the very robust design (aluminum housing) and the possi-

bility of upgrade/enhance units performances with simple slot in card (pc-like thru the DEXB expansion bus)

Moreover MRK960 system is already set up for the exclusive PTT funcon (remote command), developed and

patented by Wisycom and now appreciated in the broadcast world:

Simply pushing this button (PTT), the presenter causes the remote switching of the receiver’s output-

line, from the “main line” to the additional “intercom line”, in order to be able to talk “o-air” directly

with the technical team. Then all PTT’s MICs can be connected in pre-fading allowing a clever intercom

setup.



•• Read this safety instrucon and the manual rst.

•• Follow all instrucons and informaon.

•• Do not loose this manual.

•• Do not use this apparatus under the rain or near the water.

•• ATTENTION: supply the apparatus with a correct mains voltage and with the ground connecon. Check the

power cord integrity.

•• The power cord must be protected from damage.

•• Do not install the apparatus near heaters or in hot environments, do not use outside the operang tempera-

ture range.

•• Mount the apparatus as indicated in the instrucon, do not block side grids for air venlaon.

•• If the external air lter is mounted, clean it regularly.

Pag. 3

MRK960 dual true diversity receiver

•• WARNING: do not open the apparatus, RISK OF ELECTRIC SHOCK!

•• Do not open the apparatus, only qualied service technician are enabled to operate on it. The apparatus

needs servicing when is not properly working or is damaged by liquids, moisture or other objects are fallen

in the apparatus.

•• Use only accessories or replacement parts authorized or specied from the manufacturer.

•• Do not supply more than 7 apparatus MRK960 from the mains output, see power requirements for other

apparatus.

•• Clean the apparatus only with dry cloths, do not use liquids.

•• The ON/OFF is a double pole circuit breaker, but to ensure the complete disconnecon of the apparatus,

disconnect the power cord.

•• Report the serial number and the purchasing date in front of the manual, it is needed to have proper re-

placement parts or accessories from the manufacturer.

•• When replacement parts are needed, use only replacement parts authorized from the manufacturer. Sub-

stuon with not authorized parts could result in electric shock, hazards or re.

» Keep attention on all the labels with warnings or hazards on the apparatus.

•• WARNING: The apparatus is intended for professional use; anyway the manufacturer alerts the user that

the headphone output power of the apparatus could exceed the level of 85 dB(A) of sound pressure level

and this could be dangerous for the hearings. Do not use the headphone with high power level or for long

me. Reduce the power or suspend the hearing in the case of any kind of hearing problem.

Main features

MRK 960 is a modular wireless-microphone receiver System in a 19” 1 unit module, stackable, with dual true

diversity receivers:

•• Extreme RF (radiofrequency) performances and reliability.

•• Tuning windows of 240 MHz with tunables lters (2 ch’s independent): 470/840 MHz (TV ch 21/67)

with internal acve splier

•• Wisycom digital expansion bus (DEXB) for future upgrade/enhancement thru simple slot-in card (pc-like).

DEXB can host DSP (40bit dsp processing) upgrade cards providing:

•• digital output (i.e. AES3, Ethersound)

•• mul-companding compability

•• future digital funconality enhancements.

•• Balanced electronic AF output (low impedance transformer-coupled oponal)

•• 2 USB’s connectors for conguraon/monitor and cascade rack connecons

•• Automac scan for best channels, squelch and other automac setup

•• Infrared interface (i.e. for system setup, microphone programming)

•• Automac transmier re-programming (thru infrared, sync funcon)

Pag. 4

MRK960 dual true diversity receiver

•• Soware to monitor/setup units and with spectrum eld analysis

•• Ethernet 10/100 base Tx network interface for conguraon/monitor

•• Digital audio interfaces: AES/EBU (with word-clock in/out)

Oponal:

•• Ethersound

interface

•• Push to Talk (PTT) funcon with audio exit and GPI signals (patented)

•• Very low impedance transformer outputs



The MRK960 is a professional dual diversity receiver for wireless microphones recepon especially designed

for broadcast producon, live stages, theatres and top professional applicaons.

It’s winning performances are:

• High immunity on strong rf environment

• Huge switching bandwidth

• High audio performances and exibility thanks to the digital processors

• High reliability and durability

One of the milestones in the design of the MRK960 is high reliability: most of the circuitry of the receiver is

independent one from each other.

Here below a schemac with an overview of main receiver funcons.

Starng from the antenna inputs, each antenna could be indipendently powered from a single power regula-

tor monitored from the microcontroller.

For each antenna the RF signal is splied in the receiver 1 and in the receiver 2 (antenna A and antenna B)

with a wide band splier. In this way any one receiver could be tuned in any frequency of the switching range

(370 MHz).

Receiver 1 and 2 are true diversity receivers: each one is made of two receivers tuned on the same frequency,

hereaer called secon A and secon B. The receiver 1 secon A and the receiver 2 secon A are connected

to the antenna A, the receiver 1 secon B and the receiver 2 secon B are connected at the antenna B.

Each receiver has its own demodulated signal and its own RSSI signal (Receiver Signal Strenght Indicaon); a

microcontroller select or combine signals from secon A & B to have the best audio. The demodulated signal

ows to the digital audio processor.

Pag. 5

MRK960 dual true diversity receiver

MRK960: main block diagram

Receiver - 1- A

Receiver - 1- B

Receiver - 2- A

Receiver - 2- B

True Diversity

Control Rx 1

True Diversity

Control Rx 2

Communic.

and control

interface

Receiver supervisor

microcontroller

and user interface

Front panel

Digital

output

Antenna inputs

Line 1

Line 2

Com Rx 1

Com Rx 2

AES3 Output

INFRARED

USB

Digital

audio

processor

Analogue

output

PTT

output

Ear-ph Left

Ear-ph Right

Ear-

phone

work clock

Ethersound

Ethernet

The data sub carrier is digitally ltered to a very selecve equivalent lter (bandwidth 3Hz). Each lter has its

own data demodulator, one for medium speed data detecon at the output of the rst lter and one at low

speed data detecon at the output of the second lter. All the two demodulators are connected to the super-

visor micro controller for the data baery detecon and signalling.

Digital audio processor(for each receiver): the demodulated signal is ltered by an an aliasing low pass lter

and then converted in the digital domain with a 96KHz 24bit audio A/D converter. The digital signal processor

(DSP), working in double precision, replicates all the analog funcons with very high accuracy, ultra low distor-

on and without typical analog problems like components tolerances or long term or temperature dris etc.

The high speed audio algorithms maintains the audio delay at about 0.390 milliseconds, making it ideally for

live events and to keep audio delay as short as possible. The DSP unit also lters and demodulates the data

carrier and communicates all the parameters and informaons to the supervisor micro controller. The audio

output goes to the digital outputs (AES3) or is converted in the analog domain with a high quality 24 bits

96KHz D/A converter and an an-aliasing lter.

The analogue audio signal is routed in three parallel ways, LINE, COM and HEADPHONE MONITOR amplier.

The HEADPHONE MONITOR amplier is controlled by the buons on the front panel and by the volume knob.

The monitor output depends on the squelch and on the tone squelch only in the TSQ ON selecon. In TSQ OFF

and in TSQ ADV the monitor output is muted only by the squelch control.

The two analogue audio ways, LINE and COM, has the same audio quality and are controlledy by the “Tone

squelch matrix”. Each audio driver has a VCA for the so switching of the audio signal and the mung func-

ons, controlled by the supervisor microcontroller. Aer the VCA, an electronically balanced amplier drives

the output signal, directly or thru a very low impedance screened audio transformer (oponal). The audio

output without transformer could withstand up to +52 Vdc of phantom supply with no damage and up to

100V with transformer.

Pag. 6

MRK960 dual true diversity receiver

EA B C



Front panel functions

MRK960 allows an easy and quick conguraon using buons, push knobs and displays.

The front panel is funconally divided in the following secon:

Scan & Squelch: automac scan and squelch sengs;

Infrared: remote controlling and MIC setup through infrared interface.

Receiver 1: “receiver 1” conguraon and monitor of radio/deviaon levels.

Receiver 2: “receiver 2” conguraon and monitor of radio/deviaon levels.

Monitor: monitoring audio output on headphone jack (6.3mm - ¼”).

Power & Booster: powering ON or OFF the receiver and the antenna boosters



The funcon SCAN iniates an automac procedure for the choice of the less noisy channel in the selected

group of channels; the scan funcon measures the oor noise of all the channels of the selected group and

show the result in the display. This is a quick way to nd the best channels to use in the selected group. When

pushed the scan buon, it is needed to setup or conrm the group of channels for the scan.

SQUELCH iniates the automac procedure to setup the level of the squelch. This is an automac

way to quick setup the squelch for the current frequency. The transmier must be o, then push

SQ buon to let the system nd the opmal value. You can later accept, modify or discharge this

setup.

IR interface window: for communicaons between the MRK950 and a transmier. You have to

put the IR interface of the transmier, with the IR interface acve, in front of this window. This is

needed for example in the SYNC funcon.

Pag. 7

MRK960 dual true diversity receiver

RECEIVER 1 and RECEIVER 2

Area A: 3 LED bars:

• twobarsfortheRFlevelsindBuVolt(diversityA&Bantennalevel),

• FMmodulationofthereceivedchannel(modulationin%referredtothenominaldeviation)

• LIN:audioinlineoutputactive

• COM:audioincomoutputactive(optional)

• GPI:g.p.i.commandthruopto-isolatedrelay,active(optional)

• DATA:datasubcarrierfrommicrophonetransmitterdetected

Area B:display(256x64pixelsyellowOLEDdisplay)

Area C:3pushbuttons(membrane).

Thefunctionofeachbutton(upper,middleandlower)willbereadablefromthecontextmenuonthe

display.

Area D:Pushrotaryknobandlightindicator

 Warning(YELLOW)andAlarm(RED)lightindicator:

• YellowFixed lightindicator(Warning)whenthereisnoaudioinboththeaudiooutputs(COMand

LINE)

• RedSlowBlinking lightindicator(LowAlarm)whenthebatterylevelofthetransmitteris≤25%

• RedFastBlinkinglightindicator(MediumAlarm)whenthebatterylevelofthetransmitteris≤12%

• RedFixedlightindicator (HighAlarm)whenabooster(AorB)hasashortcircuit.Moreoverthefol-

lowingmessageappearsontheOLEDdisplay:“OverCurrentonantennaA/B”

MONITOR

Monitor 1 and 2:it acvates monitor audio on jack output (6.3mm - ¼”) for receiver

1 and 2, respecvely (a green LED is lighted when audio is enable). Audio level can be

adjusted with the rotary knob. The red led (CLIP) indicates a clipping in the audio moni-

tor output.

POWER & BOOSTER

BOOSTER:it acvates antenna powering (boosters) with 12VDC (200mA max) and the

green LED is lighted. Blinking LED indicates a faulty condion, in this case power down

the device and check for short circuits or overloads in the RF cables or boosters.

Booster supply for antenna A and antenna B are indipendent, switchable from the RA-

DIO > OPTIONS menu.

POWER: ON/OFF square powering buon turns on/o the receiver. When in OFF posi-

on both phases are disconnected from power.

A B C D

Pag. 8

MRK960 dual true diversity receiver



All the basic informaon on the receiver status are readable in the main view of the LCD display.

The main view has the following info:

 receivername,

 currenttuningfrequency

 currentchannelnumber

 currentgroupnumberandgroupname

 TVchannelusedforthecurrentfrequency

 ToneSquelchcurrentsetup

 AESworkclockstatus(sincefw1.1.0.Horabove)

 Squelchlevel(microVolt)

 NETconnectiontoahostPC(USBorEthernet)

 AnalogaudiooutputlevelatnominalFMdeviation

 statusoftheoutputlines(audioline,audiocom,gpi)anddetectionofthedigitaldatacarrier(i.e.transmit-

terbatterydatacarrierortonesquelch),

 transmitterbatterychargestatus.

Thru the main menu on the LCD display and the LED bars for the RF level and modulaon the user has the

complete monitoring in real me of the wireless channel in use.

Menu tree

To access the conguraon menu of the receiver is necessary to press the rotary knob (at the right of the dis-

play). This allows you to access the main menu.

Pressing rt the rotary know shows a hidden window (area 11 the image

of the main view) with three main headings: “RADIO”, “AUDIO”, “SYNC“.

To acvate one of the items in the menu, press the corresponding buon

to the right of the display (see picture hereaer).

6 7 8 9

Press the knob

SYNCRADIO

AUDIO

Pag. 9

MRK960 dual true diversity receiver

Radio menu

The rst item on the menu tree is “RADIO”. Pressing the upper buon (RADIO), you go at the RF funcons

menu of the receiver, as shown below:

Pag. 10

MRK960 dual true diversity receiver

Chan-Group

The CHANNEL-GROUP item enables the user to edit channel, channel group and frequency of the selected

items. Change, rotang the knob, the channel or the group of channels and conrm or exit with the buons.

To edit the frequency of selected channel, press the middle buon and change it with the knob. Press the

knob to move between MHz and KHz. Conrm or exit with the buons.

As shown in the above picture, the display area has 3 rows with:

1] Channel number (0 to 60) and Channel frequency (in

25kHz step)

2] Group number (1 to 40) and group name (8 char.)

3] Group descripon (30 char.)

The MRK960 has 40 groups of 60 channels each. Normally this is too much for wireless microphones applica-

ons.

Connecng with computer with WISYCOM MANAGER soware, it is possible to hide single channels or even

complete groups of channels: once hidden those items are not shown anymore on the channels or groups

selecon. To show channels or groups hidden use again the WISYCOM MANAGER soware.

Using this soware it is also possible to lock channels or groups. When a channel is locked, it is not possible to

change the frequency from the front panel of the receiver. Locking a group means that all channels are locked.

When a channel or a group are locked, at the le of the group name in the Chan-Group menu will appear a

lock icon as shown in the picture below. When the lock picture is shown, the central buon is not displayed,

thus changing frequency is not possible.

Gr. name

The second item on the radio menu is GROUP NAME; with

this funcon is possible to assign or change a name to a

group of channel. This short name (8 character) is displayed

at the right of the group number in the main display view.

First chose the the group and then press the knob. You will

be able to edit any character of the group name rotang the knob. Push the knob to edit the next character.

Conrm or exit with the buons.

Squelch

The SQUELCH funcon allows to assign a value at the squelch

of the receiver. Rotang the knob it is possible to change cur-

rent squelch level from OFF (it means no audio squelch) to

1mV. Pressing the knob you could setup the desired level and

also congure you measurement unit between microVolts

and dBµV. At the end conrm or exit with the buons. There is also an automac procedure to set up the

squelch level, it will be discussed later in this document at the Autoset SQUELCH item.

Pag. 11

MRK960 dual true diversity receiver

Walk test

The WALK TEST funcon records the RF level of the two antenna inputs, separately, for a total me of 90 sec-

onds. Using the rst buon, it is possible to choose what to plot: the rf level of the antenna A or B, the Max

value between antenna A and B or both antenna levels separately. Press START and walk on your area with a

wirelss MIC (transming at the current frequency) while receiver records all received RF levels. At the end of

the sweep me it is possible to have a look on the graph and check if there are some “hole of RF signals” and

evaluate your wireless coverage.

Finally push the 3rd buon (EXIT) to leave this fucnon. As “rule of the thumb”, the signal coverage of the

stage could be considered good if, in all the stage, the signal “MAX AB” is never lower than 10µV or 20dBµV.

The plot in the picture, shows a very low coverage with some areas not covered by the two receiving antennas.

In this case probably the posion of the antennas must be changed and/or the gain of the boosters adjusted.

Note:theunitforRFlevelisthesamechosenforthesquelchlevel(dBuVolt or uVolt)



Name

The opons NAME allow you to change the name of the receiver. This is the name displayed in the top of the

display in the main view and is the name sent to the transmier with the sync funcon (for transmiers with

this advanced capability).

Use the knob to change the name and the buons to save

or exit from the funcon (12 alphanumeric characters: A-Za-

z0-9, case-sensive).



Display brightness allows to change the brightness of the display from 1 to 15 level (step 1 dB).

Display LOW Timeout [0÷120 sec] controls display behaviour as follow:

- Aer a rst mer meout without any input on the receiver (buons or wheel) the display gost on “RE-

DUCED BRIGHTNESS MODE”

- Aer another mer meout, the receiver goes into “LOW BRIGHTNESS MODE”, and leaves current menu to

be back on TOP MENU.

Display OFF Timeout: [OFF, 5÷240 min] aer the meout without any input on the receiver (buons or wheel)

the display switches o. (OFF=display always power on.)

NOTE: Each receiver has indipendent display parameters.



allows to select which antenna input (A, B or A+B) has to be powered on by pressing BOOSTER buon

from the front panel.

Pag. 12

MRK960 dual true diversity receiver

Info

the INFO funcon shows many important features or informaon of your MRK960 receiver:

» Range:infoaboutthefrequencylimitsofthereceiver.

» Temp:internaltemperatureofMRK960.

» Ant.AandAnt.B:themeasureoftheoutputcurrentforpoweringtheboostersconnectedonantenna

inputAeBconnectors.Thecurrentmeasurementisactiveonlywhenboostersareswitchedon.The

boostersupplyvoltageis12Volts.

» Serial:serialnumberoftheMRK960receiver.

» Errors:numberofinternalerrorsdetectedbythereceiver,usefulforserviceormaintenance.

» App:releaseversionofthemainapplicationrmware.

» Appbl:releaseversionofthemainapplicationrmwareupdater(bootloader).

» Netw:releaseversionofthenetworkcommunicationrmware.

» Netwbl:releaseversionofthenetworkcommunicationrmwareupdater(bootloader).

» DSP:releaseversionoftheDSPrmware.

Note:thecompletesoftwareandhardwarestatusisdisplayedswitchingONthereceiverwithaknob

pressed.Pressthisknobasecondtimetoexitthisfunction.

RF test

This menu gives some informaon of the RF signal measured.

Note:lowlevelofTsq.modmeansthattheTonesquelchisnotdetectedfromthereceiver



The FACTORY PRESET resets the following setups to factory defaults: tone squelch (OFF), noise reducon

system (ENR), audio output level (12dBu), cal tone (OFF), audio matrix, booster supply (OFF) and headphone

selecon (OFF).

Note:receivernames,frequencies,groupsorchannelsinformationareNOTchanged.

Pag. 13

MRK960 dual true diversity receiver

Audio menu

The second item on the menu tree is “AUDIO”.

Noise Red

The NOISE REDUCTION SYSTEM is used to select your current noise reducon system in the audio path.

Thanks to the DSP board, it is possible to choose dierent types of audio processors. MRK960 supports, as

standard conguraon, the following type of “Companding system”:

NONE-d50 NO compander, 50µs de-emphasis

Analogue baery data & PTT (Wisycom®)

NONE-d75 NO compander, 75µs de-emphasis

Analogue baery data & PTT (Wisycom®)

ENR-WISY Wisycom ENR compander, noise opmized

Digital baery data & P (Wisycom®)

ENC-WISY Wisycom ENC compander, voice and high-delity opmized

Digital baery data & P (Wisycom®)

Use the buons to save or exit from this funcon. Depending on selected NOISE REDUCTION SYSTEM, tone

squelch funcon and transmier baery status could be enabled or disabled (since not all the wireless mi-

crophones have this enhanced funconality).

Tone sq.

The TONE SQUELCH funcon is an advanced funcon (whose behaviour depends on selected noise reducon

system). This chapter explains TONE SQUELCH operaons when associated to a Wisycom wireless microphone

with the ENR-WISY or ENC-WISY as acve noise reducon system. Other types of wireless microphones could

have dierent behaviour or could not work properly. Here-aer the complete tone squelch funcon, when-

ever the receiver does not have all the opons installed, some funcons will be hidden.

Pag. 14

MRK960 dual true diversity receiver

The tone squelch selecon could be OFF, ON or ADV (advanced). Aer the SAVE of tone squelch selected, a

CONFIG submenu appears on the right. Enter on the CONFIG submenu to change the seng of the choosen

Tone Squelch (see matrix below). With the knob and the buons, it is possible to choose, for any one of the

three TSQ modes, the status of the audio outputs LINE and COM and in the TSQ ADV mode it is possible to

choose the status of outputs LINE, COM and GPI, when the transmier PTT buon is released or pushed. The

dot in the circle on the le of the display shows the actual seng for the tone squelch funcon.

Tone squelch OFF enables the audio output on LINE and

COM (if present) connectors always, it could be muted only

by the squelch on RF signal (the RF squelch has always prior-

ity).

Tone squelch ON enables the audio output on LINE and COM

(if present) only if the transmier sends the correct iden-

caon tone signal (tone squelch).

Tone squelch ADV (with or without PTT opons), on micro-

phone transmiers, gives more possibilies of audio roung

and GPI signalling.

Note:thetonesquelchcouldnotsubstitutethesquelchon

theRFsignallevel.ForthebestperformanceofthereceiveritisbettertousetheSQUELCH&TONE

SQUELCHtogether.



With this parameter, it’s possible to enable a delay on the acvaon of the audio when the tone squelch is

ON. If the tone squelch is set to ADV (advanced), this delay is not enabled.

This delay is set to 500ms by default but it’s possible to change it from 100 to 2000ms (step 100ms) or OFF.

When the delay is set, the output audio is enabled only if the tone squelch is detected during all delay me.

It permits to avoid that a brief strong interference, with the same freq of the tone squelch, enables the audio

in output.

Note:thisfeatureisavailablefromrmwareversion1.1.0.w.InthepreviousFWversionsthedelay

wasforzedtoOFFandnotcongurablebytheuser.



The OUT LEVEL funcon allows the adjustment of the audio level on the LINE and COM balanced outputs. The

nominal level, used also in the technical specicaons of the receiver, is 12dBu at nominal modulaon and

could reach 18dBu to 20dBu in clipping. This level could be too high for some audio mixing units, so with the

out level funcon it is possible to reduce the nominal level from 12dBu to 6dBu or 0dBu. This seng is unique

for LINE and COM.

Note:theaudiooutputlevelcouldbefurtherreducedby30dBwithaswitchbelowtheXLRoutputcon-

nector,intherearpanel.

Pag. 15

MRK960 dual true diversity receiver

Cal. tone

The CALIBRATION TONE funcon generates a tone (at specic frequecies) or a sweep of tones at the audio

outputs. Change the value of the following parameters according to the desiderable calibraon tone:

» Mode:selectthetypeofcalibrationtone(Tone/Sweep)

» Out:selecttheoutputsforthecalibrationtone(onlyLINE,onlyCOMorLINEandCOMtogether)

» Level:selectthelevel(-6dBFSor-26dBFS)

» Frequency(onlyforTone):444/442/440/1000Hz

» Freqstep(onlyforSweep):ocatve÷1/24octave

» Timestep(onlyforSweep):1sec/100ms

With the buons it is possible to start, stop and exit from the tone generaon. The output not selected for the

tone generaon will be muted.

When the tone is acve at least in one output, the led bar of the deviaon indicates the level selected.



This opon is normally set to OFF. Set to YES when you need:

•• to increase the reliability in case of failure

•• to increase the reliability in case of transmier baeries empty

•• to increase the security against fading due to reecons on the radio link

When a receiver is set to frequency diversity YES, the audio output is calculated from the best RF signal re-

ceived from the two receivers.

WARNING: two transmiers tuned with the two receivers must be placed on the same audio source and must

have the same conguraon (ex. gain, tone squelch seng, RF power, distance from the audio source….).

NOTE: the Noise reducon can be dierent.

Note:Frequencydiversityineachreceivercanbesetindependently.

Note:Withfrequencydiversityenabled(settoYES),theToneSquelchmenuallowsonlythesettingop-

tionsONandOFF(theADVoptionisnotallowed).

Frequency diversity example:

RX1 tuned on f1 with Frequency Diversity set to YES.

RX2 tuned on f2 with Frequency Diversity set to NO.

Pag. 16

MRK960 dual true diversity receiver

TSQ detect alarm

This opon is normally disabled.

If enabled, the receiver shows an alarm “Tone squelch not detected” in case of absence of tone squelch. The

alarm appears when the audio output becomes suddenly muted in the following condions:

•• “AUDIO>Tone sq” set to ON or ADV

•• RF level > squelch

•• Tone squelch not detected



The SYNC funcon, selected from the main menu with the lower buon, is useful to tune a transmier on

the same frequency of the receiver via the IR interface. Before starng the sync funcon tune the receiver

on desired channel, manually or using the SCAN ulity. Aer this, enable the IR interface on the transmier.

Now press the knob and the lower buon to start the SYNC funcon. Keep the IR window of the transmit-

ter in front of the IR window of the receiver and, as soon as the connecon is done, the receiver will send to

the transmier all the informaon needed. If the operaon is not possible, (i.e. the frequency range of the

transmier is not compable with the frequency of the receiver), the display will show an error message. If

the transmier has the funcon “NAME” enabled, when the sync funcon is completed it will show the same

name of the syncronized receiver.

Audio output RX1 is calculated from the best RF signal received from the two receivers.

Audio output RX2 is calculated from the RF signal received from RX2.

Pag. 17

MRK960 dual true diversity receiver



The SQUELCH AUTOSET funcon helps the user to set the squelch level of the receiver at a good level for the

selected channel.

Aer pressing the SQ autoset buon, the two receivers ask to switch o the transmier and

then, aer the user conrmaon (on one receiver or all the two receivers at the same me), it

starts to measure the noise in the selected channel.

A few me later, aer some calculaon, the receiver proposes the new squelch level.

The user could then accept, refuse or modify it by means of the buons and of the knob.

Note:duringtheAutosetSQUELCHfunctionitisnotpossibletochangetheunitofthesquelchvoltage.

SCAN

The SCAN funcon is very useful to discover the best channels to use (the channels with lower RF noise) in

the selected group. Aer pressing the SCAN buon, both receivers are ready to start with the SCAN funcon.

It is possible to select the receiver 1 or the receiver 2 or both (i.e. simultaneously scan on dierent groups).

With the rst menu on the display it is possible to choose the group of channels for the scan and, pressing

the knob, is possible to dene a reference line drawing in the nal scan result graphic, just for user reference.

Pressing the knob the focus change between REF LINE and GROUP.

Pressing the START buon, an alert window remind the user to switch o all the transmiers before starng

the SCAN, press START again and the SCAN funcon will start. At the end of the analisys, on the display it is

possible to see the graph of the RF levels measured in each channel and, rotang the knob, it is possible to

move the marker on the boom of the graph just to see the channel number and the RF level measured for

that channel.

Pressing the knob it is possible to have a graph in rank order instead of channels order, so, it is very simple in

rank order to nd the less noisy channels because they are in the le part of the graph.

The marker is always acve rotang the knob.

Pressing the knob the graph changes between rank order to channel order again.

For terminang the SCAN funcon, press the lower buon on the right of the display.

Pag. 18

MRK960 dual true diversity receiver

In the above picture a typical graph of the scan funcon (only the graph area of the display). This graph, or-

dered by channel numbers, shows the RF levels in dBµV for each channel in the selected group (i.e. Ch: 00).

Rotang the knob the small arrow cursor moves from a channel to the next one; on the right of the graph it is

possible to see the rank of the channel selected by the cursor, its number, its frequency and the RF level. Press-

ing the knob the order of the graph became the rank, not the channel number. In this way it is more simple to

choose channels with lower RF noise, they are in the le part of the graph. See at the picture below:

In this graph the channels are ordered by rank. Turning the knob it is possible to change the channel and read-

ing its number, frequency and level of RF noise.

The horizontal dashed line is the squelch level set before starng the scan.

Connecng an headphone at the monitor output, is possible to ear the signal in the channel selected by the

knob. If the RF signal is below the squelch level, the upper buon near the display disable/enable the squelch

so the audio output is enabled also for weak RF signal.

The SELECT buon is the exit from the SCAN funcon tuning the receiver on the selected channel, the EXIT but-

ton exits from the SCAN funcon leaving the receiver channel unchanged.

Pag. 19

MRK960 dual true diversity receiver

OPERATING INFORMATIONS



Two RF level led bars for each receiver indicate measured RF level at the antenna input of the receiver in the

selected channel. For a typical diversity recepon it is a good starng point to consider that the two signals

should have the same average level over me, but this could be dierent while moving the transmier on the

stage. The important issue is that moving the transmier on the stage, the diversity has to work switching

from one receiver to the other receiver as indicated by the two blue leds on the top of the bars. When the

RF levels of the two inputs have similar level, the diversity control enable the two receiver at the same me,

further increasing the S/N rao at the audio output.



The third led bar of each receiver indicates current channel modulaon as percentage of nominal deviaon

(not the audio output level). The dierence between modulaon and audio level is because normally there is

a preemphasis on audio transmission and some manufacturer uses dierent compression values and dierent

audio frequency equalizaon. Therefore to have the maximun eciency of the radio channel it is important

to use the highest modulaon bandwidth possible, in respect to the dynamic range of the audio signal and the

manufacturer specicaons. If the receiver MRK950 has the DSP board opon, the scale of the modulaon

will be changed according to the nominal modulaon of the type of microphone and manufacturer selected

in the NOISE REDUCTION SYSTEM. The modulaon led bar is blank when the squelch and/or the tone squelch

opens the audio output circuit (or if there is no modulaon on the transmier, of course). Adjust the gain of

the audio chain in the transmier to have in the maximum modulaon peaks the 100% of modulaon band-

width, leaving the next 6dB of modulaon margin before clipping (red PEAK led) for extra sound pressure

margin. If the audio level is not exactly known, be conservave and adjust the microphone gain in a lower

posion to avoid clippings during the working session.



On the main display of each receiver is always well visible the baery status of the transmier (area 12 of the

main view). The resoluon of the indicaon depends on the transmier. Wisycom transmiers send 8 levels

of baery charge status, other competors 6 or 4 or 3 level (full, half, empty).

When the transmier is a Wisycom, the display of the baeries indicate the correct icon and the percentage

of the charge but, when the charge reach the 25% the baery area on the display became ashing, when the

charge reach the 12,5%, the illuminaon of the display is ashing to give an high visibility alarm to the user.

Pag. 20

MRK960 dual true diversity receiver

1Mainsoutput.Donotconnectmorethan8

units.

 Mainssocketinput.

 Mainsfuse(2A-T).

 EthernetconnectorRJ45forLANconnectionof

thereceiver.Theledson theconnectoreindi-

catethestatusoftheconnection(LinkandAc-

tivity).

 AES/EBU XLR 3 pin output connector, digital

audio output transformer isolated, balanced.

ThisispartoftheAES/EBUoptionalboard,to-

ghetherwith6,7and22.Hereitispossibleto

(Optional)

 Wordclockinputforexternalsyncronizationof

digital audio output.

 75ohmsterminationswitchforwordclockin-

put.

 AntennaBinput,BNCconnector,DCoutputfor

boosterpowersupply.

 XLR3pinmaleconnector,COMaudiooutputof

thereceiver2,balanced.(Optional)

XLR3pinmaleconnector,LINEaudiooutputof

thereceiver2,balanced.

GPIoutputofthereceiver2,1/4”(6,3mm)ste-

reojacksocket.(Optional)

 XLR3pinmaleconnector,COMaudiooutputof

thereceiver1,balanced.(Optional)

XLR3pinmaleconnector,LINEaudiooutputof

thereceiver1,balanced.

GPIoutputofthereceiver1,1/4”(6,3mm)ste-

reojacksocket.(Optional)

 AntennaAinput,BNCconnector,DCoutputfor

boosterpowersupply.

 Unbalanced LINE audio output of receiver 1,

1/4”(6,3mm)stereojacksocket.

 Switchesforshortingthepin1oftheXLRcon-

nectorsofreceiver1tothereceivergroundor

not.

 Switches for attenuating the audio output le-

velontheXLRconnectors.Theattenuationis

30dB.

 Unbalanced LINE audio output of receiver 2,

1/4”(6,3mm)stereojacksocket.

 Switchesforshortingthepin1oftheXLRcon-

nectorsofreceiver2tothereceivergroundor

not.

 Switches for attenuating the audio output le-

velontheXLRconnectors.Theattenuationis

30dB.

 Wordclockoutput,fordaisychainconnection.

BNCconnector.(Optional)

 LINKconnection,forcascadeconnectionofre-

ceivers,forremotecontrolfunctionality.USB-A

connector.

USB-B connector for PC connection if this

MRK960isasubnetcontroller.IfthisMRK960

ispartofasubnet,thisconnectormustbecon-

nected to the LINK connector of the previous

MRK960.

 Productidenticationlabel.

 AntennaAoutput,BNCconnector(forantenna

splitting)

 AntennaBoutput,BNCconnector(forantenna

slipping)

Rear panel

12 13 14 15

1627

3 9876

192023 22 2125 24

La pagina sta caricando ...

WisyCom MRK960 Manuale utente

Marca: WisyCom

Modello: MRK960

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: WisyCom MRK960 User manual

WisyCom MRK960 Manuale utente

WisyCom MRK960 Manuale utente

in altre lingue

Documenti correlati

Altri documenti