Western Telematic CAS-81 Manuale utente

Marca: Western Telematic

Modello: CAS-81

Tipo: Manuale utente

Questo manuale è adatto anche per

Switch CAS-81

WTI Part Number: 12365

Rev. C

CAS-81

8-Port Code Activated Switch

User's Guide

5 Sterling · Irvine · California 92618

(949) 586-9950 · Toll Free: 1-800-854-7226

Fax: (949) 583-9514 · http://www.wti.com

Table of Contents

1. In tro duc tion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2. Unit De scrip tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.1. Front Panel In di ca tors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2. Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

3. In stal la tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1. Set DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1.1. Data Rate (Baud) Se lec tion (Switches 1 through 3) . . . . . . . . . . . . . . 3-1

3.1.2. Ti me out Se lec tion (Switches 4 and 5) . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1.3. Quiet Mode (Switch 6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1.4. Auto Con nect Se rial Port 1 (Switch 7). . . . . . . . . . . . . . . . . . . . . . 3-2

3.1.5. Broad cast Mode (Switch 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.1.6. Force CTS (Switch 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.1.7. Force DCD (Switch 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.2. Con nect Power Ca ble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

3.3. Con nect De vices to Se rial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

3.4. Con nect Con trol Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

3.5. RS422 Line Driver Op tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

4. Op era tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1. Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2. AS CII Char ac ters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.3. Com mand String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.4. Com mand Re sponse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4.5. Port Gat ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4.5.1. Open Port Gat ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4.5.2. Close Port Gat ing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Ap pen di ces

A. De scrip tion of Sys tem In ter faces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-1

A.1. Con trol Port (DB25 Fe male) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-1

A.2. Se rial Ports 1 through 8 (DB9 Male) . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-2

A.2.1. RS422 Line Driver Op tion . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-2

B. Speci fi ca tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-3

C. FCC No tice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-3

D. Cus tomer Serv ice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-4

List of Figures

2.1. Front Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2. Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

A.1. Control Port / Serial Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-1

A.2. RS422 Option Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-2

1. Introduction

The CAS-81 Code Activated Switch brings the convenience of code-based RS232 switching to

sites with multiple terminals, printers, and peripherals. The CAS-81 enables a single RS232

Control Port to switch between 8 devices via an ASCII code sequence.

Code based switching lets you control the CAS-81 from your PC or mainframe. When a

modem is attached to the Control Port, the CAS-81 can also be managed from a remote

location. Devices can be connected or disconnected by sending commands from a remote PC

via modem.

The CAS-81 can operate at speeds up to 115,000 bps and passes data in "real-time" with no

delays. Binary and graphics files can be safely passed due to the unique 8 character switch

instruction, which considerably reduces the chances of false switching.

A broadcast mode makes it easy to mass-address a group of printers, display devices, or an

array of laboratory instruments by directing the data on the Control Port to all Serial Ports

simultaneously. The broadcast mode may be selected by code or permanently selected by the

Select Switch.

An Auto-connect feature allows the Control Port to automatically connect to Serial Port 1 each

time the unit is powered up, or after a timeout or disconnect. This provides a data path to a

critical device in case of a power failure, or convenient connection to commonly used

equipment.

Each Serial Port may be configured for a balanced RS422 long distance line driver by simply

removing the socketed RS232 driver chip and plugging in an optional RS422 module. When

the module is installed, an LED on the back panel indicates the port is RS422.

Applications

· Industrial Robotic and Numeric Control

· Remote Diagnostics

· Laboratory Equipment Polling

· Data Acquisition

· Network Management

Typographic Conventions

Throughout the manual, typefaces and characters have been used to denote the following:

^ (e.g. ^X) Indicates a key combination that is used to invoke a command.

For example, the text "^X" (Control X) indicates that the [Ctrl] key and

the [X] key should be pressed simultaneously.

COURIER FONT Indicates characters typed on the keyboard.

For example, ^VS or ^C#.

1-1

2. Unit Description

2.1. Front Panel Indicators

ON: Indicates power to the unit is ON.

RDY: Indicates unit is Ready to operate. A steady blink indicates that the CAS-81 is

operating normally.

TXD: Indicates that data is being received at Control Port pin 2.

RXD: Indicates that data is being transmitted out Control Port pin 3. Also indicates that

data is being received by pin 2 of a selected Serial Port.

RTS: Indicates that the "Request to Send" signal is present at Control Port pin 4.

CTS: Indicates that the "Clear to Send" signal is present at Control Port pin 5. Also

indicates that the "Clear to Send" signal is present at pin 8 of a connected Serial Port.

Always high when all ports are disconnected.

DTR: Indicates that the "Data Terminal Ready" signal is present at Control Port pin 20.

DCD: Indicates that the "Data Carrier Detect" signal is present at Control Port pin 8.

Also indicates that the "Data Carrier Detect" signal is present at pin 1 of a connected

Serial Port. Always high when all ports are disconnected.

Serial Ports 1 - 8: Indicates that the corresponding numbered Serial Port is currently

connected.

2-1

Figure 2.1: Front Panel Indicators

2.2. Back Panel

Serial Ports 1 - 8: Eight RS232 DB9 male connectors configured as DTE. Accepts a

standard AT 9 pin to printer or modem cable, depending on the application. Refer to

Appendix A for more information on the Serial Port Interface.

Note that when the RS422 Line Driver Option has been installed, an LED indicator will

be present in the blank above the Serial Port. This LED indicates that the port is

configured for RS422 communication.

Control Port: RS232 DB25 female connector configured for DCE. Accepts a standard

PC to Modem Cable.

The CAS-81 will respond to proper ASCII code strings received by the Control Port.

Once a port is selected, data will pass between the Control Port and the selected Serial

Port. Refer to Appendix A for more information on the Control Port interface.

Default Switch: An 8 position DIP switch that is used to select the Control Port Data

Rate, No-data timeout period, and the Auto connect and broadcast features. This switch

is read upon power up.

AC Power: Standard AC power cord receptacle and ON/OFF switch.

2-2

CAS-81 Code Activated Switch, User's Guide Unit Description

Figure 2.2: Back Panel

3. Installation

3.1. Set DIP Switches

The DIP Switches located on the CAS-81 back panel are used to set the Data Rate, Timeout

Selection, Quiet Mode, Broadcast Mode, and other features. Note that a label on the underside

of the CAS-81 unit also describes DIP Switch settings.

3.1.1. Data Rate (Baud) Selection (Switches 1 through 3)

Select the Baud Rate for the Control Port. The Baud Rate must match that of the control

device. The CAS-81 is transparent to parity and will operate at 7 bits even or odd parity, and

at 8 bits no parity.

Switch

Baud Rate1 2 3

Down Down Down 1200

Up Down Down 2400

Down Up Down 4800

Up Up Down 9600

Down Down Up 19.2K

Up Down Up 38.4K

Down Up Up 57.6K

Up Up Up 115K

3.1.2. Timeout Selection (Switches 4 and 5)

Selects the No-Data-Activity disconnect period. If data has not been received by the Control

Port for the specified time period, the selected Serial Port will close.

Switch

Timeout Selection4 5

Down Down Off

Up Down 5 Seconds

Down Up 30 Seconds

Up Up 60 Seconds

3.1.3. Quiet Mode (Switch 6)

When enabled, the CAS-81 will not respond with "Connect/Disconnect" messages.

Switch 6 Quiet Mode

Up Enable

Down Disable

3-1

3.1.4. Auto Connect Serial Port 1 (Switch 7)

When enabled, automatically connects the Control Port to Serial Port 1 on the following

conditions:

1. Power Up

2. After a Timeout disconnect, if selected.

3. After a Code sequence disconnect.

Switch 7 Auto Connect Serial Port 1

Up Enable

Down Disable

3.1.5. Broadcast Mode (Switch 8)

When enabled, permanently activates the Broadcast Mode. Data from the Control Port will be

sent out all eight Serial Ports. Note that when the Broadcast Mode is active, all Serial Port

Status LEDs will be lit.

Data received by the selected Serial Ports will be "ord" and passed out the Control Port. If

data is received by two ports simultaneously, data output may be garbled.

A broadcast one/all jumper located on the circuit board will block received data from Serial

Ports 2 - 8. This feature allows the Control Port to receive a response message from just one

device when broadcasting commands. Receiving data from multiple devices simultaneously

may cause garbled data.

Switch 8 Broadcast Mode

Up Enable

Down Disable

3.1.6. Force CTS (Switch 9)

When enabled, forces the Control Port CTS pin to high.

Switch 9 Force CTS High

Down Enable

Up Disable

3.1.7. Force DCD (Switch 10)

When enabled, forces the Control Port DCD pin to high.

Switch 10 Force DCD High

Down Enable

Up Disable

3-2

CAS-81 Code Activated Switch, User's Guide Installation

3.2. Connect Power Cable

Make certain that the CAS-81 power switch is set in the OFF position and then connect the

power cable to the AC Power connector. Connect the other end of the power cable to a

grounded AC wall outlet.

3.3. Connect Devices to Serial Ports

Serial Ports 1 - 8 are wired as standard AT 9 pin COM Ports. Connect data cables from the

desired devices to Serial Ports 1 through 8. The Serial Ports accept AT 9 pin to printer or

modem cables, depending on the application.

Caution:

Make certain that all data cables are compatible with the CAS-81 Serial Port

interface. Please refer to Appendix A for a description of the Serial Port

interface.

3.4. Connect Control Port

The Control Port is configured to appear as a 25 pin DCE modem and accepts a standard PC to

Modem straight wired cable. Use a "Null Modem Cable" to connect a modem to the Control

Port. For a description of the Control Port Interface, please refer to Appendix A.

3.5. RS422 Line Driver Option

Each Serial Port may be configured with an optional RS422 balanced line driver. These long

distance line drivers can extend high speed transmission distance to 4,000 feet using 2 twisted

pair wiring. Only the TXD and RXD signals are transmitted. The DCD and CTS signals are

set to high.

To install the optional RS422 module, simply remove the RS232 Driver chip located on the

circuit board adjacent to the desired Serial Port’s connector and plug in the RS422 module. An

LED viewed from the back panel will indicate that the port is RS422. Please refer to

Appendix A for a description of the RS422 Serial Port interface.

3-3

CAS-81 Code Activated Switch, User's Guide Installation

4. Operation

4.1. Power Up

The ON LED indicates that AC Power has been turned on. The RDY LED indicates that the

processor is operating and the unit is READY to operate. A flickering RDY LED indicates an

AC Power brown out condition. The Control Port Status LEDs indicate the signal status of the

Control Port. The Serial Port LEDs indicate the port(s) selected. When all Serial Port LEDs

are lit, this indicates that CAS-81's Broadcast Mode is active.

Upon power-up, the unit is programmed according to the parameters selected by the setup DIP

switches, which are located next to the Control Port. (Refer to switch setup section). If you

change any of the DIP Switch settings while the unit is powered on, you must turn power off

and on to reread the switch.

4.2. ASCII Characters

The PC or controlling device connected to the Control Port must send ASCII characters at the

same data rate as the CAS-81. The unit accepts 8 bits / no parity, or 7 bits / even parity.

4.3. Command String

The command string consists of seven contiguous characters. The first 6 characters are ASCII

Control codes, and the seventh is the configuration code.

^V^X^X^V^X^Xn (Command String)

Where:

n = 0 Disconnects

n = 1 - 8 Selects Serial Port Number 1 through 8

n = 9 Enables Broadcast Mode (Select All Serial Ports)

Note that if "n" equals any character other than 0 through 9, the command will be terminated.

Examples:

To select port 3, send the following command:

^V^X^X^V^X^X3

To disconnect, send the following command:

^V^X^X^V^X^X0

4-1

4.4. Command Response

Upon receiving a valid command string, the CAS-81 will send an acknowledgment message out

the Control Port. The message is sent as 8 bits / no parity. Acknowledgment messages are as

follows:

Connected <CR>/<LF>

Disconnected <CR>/<LF>

Broadcast <CR>/<LF>

Note that the Command Response can be disabled by placing DIP Switch 6 in the UP position

to enable the Quiet Mode feature. When the Quiet Mode is active, the unit will not send

acknowledgment messages.

4.5. Port Gating

With all ports closed, data received by the Control Port will not be passed to any of the Serial

Ports. Any data received by the Serial Ports will not be passed to the Control Port. The CTS

and DCD signals will always be set high.

4.5.1. Open Port Gating

Upon receiving a valid command string at data rates up to 19,200 bps, the selected Serial Port

will open during the stop bit time of the configuration code thus allowing the next character to

be passed out the selected port.

For data rates above 19,200 bps it is necessary to delay approximately 1 millisecond before

sending data out the selected Serial Port. This prevents a character that immediately follows

the configuration character from being "cut in half".

4.5.2. Close Port Gating

Selected Serial Ports can be closed using three methods:

1. By using the Command String to select another Serial Port.

2. By Using the Command String to disconnect.

3. By using the No-Data-Activity timeout feature.

In methods 1 and 2, the Command String Control Codes will be passed out the selected Serial

Port. The Serial Port(s) will close immediately after the sixth character, thus blocking the next

character from being sent. If the configuration character was 1 - 8, then the selected Serial

Port would open. If the configuration character was 0 then the ports would remain closed.

The No-Data-Activity timeout feature can be used to make a "clean" close if the Command

String Control Codes cause a conflict with the connected devices. The Serial Port will

automatically close if no data is received from the Control Port for the time period selected by

the setup switch.

4-2

CAS-81 Code Activated Switch, User's Guide Operation

A. Description of System Interfaces

A.1. Control Port (DB25 Female)

The Control Port is a 25 pin female connector wired in a DCE (modem) configuration.

Pin Signal I/O

Not

Connected Connected

2 RXD Input - To Serial Port Pin 3

3 TXD Output Low Follows Serial Port

4 RTS Input - To Serial Port Pin 7

5 CTS Output High * Follows Serial Port

6 DSR Output High Always High

7 GND Signal Ground

8 DCD Output Low * Follows Serial Port

20 DTR Input - To Serial Port Pin 4

* May be forced high by DIP Switches 9 and 10. Always high when all Serial Ports are

connected.

Apx-1

Figure A.1: Control Port / Serial Port Interface

A.2. Serial Ports 1 through 8 (DB9 Male)

The Serial Ports are 9 pin male, wired in a DTE configuration similar to that of an A computer.

Figure A.1 and the table below describe the Serial Port interface.

Pin Signal I/O

Not

Connected Connected

1 DCD Input - To Control Port Pin 8

2 RXD Input - To Control Port Pin 3

3 TXD Output Low Follows Control Port Pin 2

4 DTR Output Low Follows Control Port Pin 20

5 GND Signal Ground

6 Open

7 RTS Output Low Follows Control Port Pin 4

8 CTS Input - To Control Port Pin 5

9 Open

A.2.1. RS422 Line Driver Option

Each Serial Port may be configured with an RS422 balanced line driver. These long distance

line drivers can extend high speed transmission distance to 4,000 feet using 2 twisted pair

wiring. Only the TXD and RXD signals are transmitted. The DCD and CTS signals are set to

high. Figure A.2 below describes the RS422 Serial Port interface.

Note: Handshake signals are not passed. All other pins are open.

Apx-2

CAS-81 Code Activated Switch Appendices

Figure A.2: RS422 Option Interface

B. Specifications

Interface:

Control Port: (1) RS232, 25 pin female, DCE configuration.

Serial Ports: (8) RS232, 9 pin male, DTE configuration.

Optional - RS422 Line Driver (TXD and RXD only)

Signals Gated: TXD, RXD, RTS, CTS, DTR, DCD

Protocol: Asynchronous ASCII, 7/8 bits, Any Parity, One Stop Bit.

Data Rate: 1200 bps to 115K bps, switch selectable

Timeout: Off, 5, 30, and 60 seconds, switch selectable

Command Sequence: Seven contiguous characters:

^V^X^X^V^X^Xn

Where:

n = 0 Disconnects

n = 1 - 8 Selects Serial Port Number

n = 9 Enters Broadcast Mode (All Serial Ports Selected)

Command Response:

Connected <CR>/<LF>

Disconnected <CR>/<LF>

Broadcast <CR>/<LF>

Power: Internal Supply - 115/230 VAC, 60/50 Hz, 10 Watts

Size: 1.75" x 17.00" x 6.5" (H x W x D) - One Rack Space

Weight: 3 pounds (5 pounds shipping)

C. FCC Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Apx-3

CAS-81 Code Activated Switch Appendices

D. Customer Service

Customer Service hours are 8:00 AM to 5:00 PM, Pacific Time, Monday through Friday. When

calling, please be prepared to give the name and make of the unit, its serial number, and a

description of its symptoms. If the unit should need to be returned for factory repair it must be

accompanied by a Return Authorization number from Customer Service.

WTI Customer Service

5 Sterling

Irvine, California 92618

949-586-9950

Toll Free: 1-800-854-7226

Fax: 949-457-8138

e-mail: [email protected]

Trademark and Copyright Information

WTI and Western Telematic are trademarks of Western Telematic Incorporated. All other

product names mentioned in this publication are trademarks or registered trademarks of their

respective companies.

Information and descriptions contained herein are the property of Western Telematic, Inc..

Such information and descriptions may not be copied, disseminated or distributed without the

express written consent of Western Telematic, Inc..

June 2000

September 1997

Part Number: 12365 Revision: C

Apx-4

CAS-81 Code Activated Switch Appendices

Western Telematic CAS-81 Manuale utente

Marca: Western Telematic

Modello: CAS-81

Tipo: Manuale utente

Questo manuale è adatto anche per

Switch CAS-81

Scarica il pdf

rapporto

in altre lingue

English: Western Telematic CAS-81 User manual

Western Telematic CAS-81 Manuale utente

Questo manuale è adatto anche per

Western Telematic CAS-81 Manuale utente

in altre lingue

Altri documenti