Amprobe TIC 300 PRO Non-Contact Voltage Detector Manuale utente

TIC 300 PRO

High Energy Tic Tracer –

Non Contact

AC Voltage Detector

User Manual

TIC 300 PRO

High Energy Tic Tracer –

Non Contact

AC Voltage Detector

User Manual

10/2019, Rev006

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material

and workmanship for 1 year from the date of purchase. This

warranty does not cover fuses, disposable batteries or damage

from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Resellers are not

authorized to extend any other warranty on Amprobe’s behalf.

To obtain service during the warranty period, return the product

with proof of purchase to an authorized Amprobe Test Tools

Service Center or to an Amprobe dealer or distributor. See Repair

Section for details. THIS WARRANTY IS YOUR ONLY REMEDY.

ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR

STAUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR

A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY

DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or

for calibration should be accompanied by the following: your

name, company’s name, address, telephone number, and proof of

purchase. Additionally, please include a brief description of the

problem or the service requested and include the test leads with

the meter. Non-warranty repair or replacement charges should be

remitted in the form of a check, a money order, credit card with

expiration date, or a purchase order made payable to Amprobe®

Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before

requesting repair. During the warranty period any defective test

tool can be returned to your Amprobe® Test Tools distributor

for an exchange for the same or like product. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you. Additionally, in the United States and

Canada In-Warranty repair and replacement units can also be sent

to a Amprobe® Test Tools Service Center (see address below).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be

sent to a Amprobe® Test Tools Service Center. Call Amprobe® Test

Tools or inquire at your point of purchase for current repair and

replacement rates.

In USA In Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe®

Test Tools distributor for a nominalv charge. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you.

European Correspondence Address*

Beha-Amprobe® Test Tools Europe

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

*(Correspondence only – no repair or replacement available from

this address. European customers please contact your distributor.)

1) Voltage sensor

2) ON/OFF Button

3) Circuit TEST button

4) HIGH range switch

5) HIGH range LED

6) LOW range switch

7) LOW range LED

8) Battery compartment

9) HOT STICK attachment point

10)

Detection Blue LED indicators

TIC 300 PRO

1

CONTENTS

SYMBOLS .......................................................................... 2

UNPACKING AND INSPECTION ....................................... 3

INTRODUCTION ................................................................4

Features ........................................................................4

OPERATION ....................................................................... 5

ON/OFF Button ............................................................. 5

TEST Button .................................................................. 5

Voltage Detection ........................................................ 6

LOW Range ...................................................................6

HIGH Range .................................................................. 6

Locate breaks in insulated wire & heating elements

...... 7

Check Outlets and Switches ........................................8

MAINTENANCE AND REPAIR .......................................... 9

Cleaning ........................................................................9

Battery Replacement ...................................................9

SPECIFICATIONS ............................................................... 10

Sensitivity: LOW Voltage .............................................11

Sensitivity: HIGH Voltage .............................................11

2

SYMBOLS

�

Refer to the manual

X

Caution Dangerous Voltage

T

Double insulated

MSHA

United States Department of Labor

Mine Safety and Health Administration

In compliance with the United States

Department Of Labor Mine Safety and Health

Administration

Conforms to relevant Australian standards.

Conforms to relevant South Korean EMC standards.

Do not dispose of this product as unsorted

municipal waste.

For Use By Trained Personnel Only

Anyone using this instrument should be knowledgeable

and trained about the risks involved with measuring

medium and high voltage, especially in an industrial

setting, and the importance of taking safety precautions

and of testing the instrument before and after using it

to ensure that it is in good working condition.

�

WARNING and PRECAUTIONS

• Use extreme caution when testing live electrical

circuits due to risk of injury from electrical shock.

• Do not exceed the maximum overload limits

(see specifications) or the limits marked on the

instrument itself. Never test voltage more than

122 kV AC RMS.

• When using the HIGH range, the TIC 410A HOT

STICK or equivalent extension pole MUST be used.

• Comply with local and national safety

requirements.

• Use proper protective equipment as required by

local and national authorities.

=

3

• Observe the proper safety precautions when

working with voltages above 33 VAC RMS to avoid

electrical shock hazard.

• Before and after hazardous voltage measurements,

test the TIC 300 PRO by pressing the TEST button

and/or on a known source such as line voltage to

determine proper operation.

• Never ground yourself when taking measurements.

Do not touch exposed circuit elements.

• Do not operate the instrument in an explosive

atmosphere.

• Do not expose this product to rain or moisture. This

increases the risk of fire or electric shock.

•

Do not rely on the TIC 300 PRO for testing shielded wire.

• Do not let the unit make contact with a live line

with voltage higher than 20 kV.

• Three phase feeder cables with conductors close to

each other may self-cancel the electric field and

will not be detected by the TIC 300 PRO tracer.

Verify that the phase conductors are separated

by at least 15 in (38.1 cm) before testing for AC

voltage.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 TIC 300 PRO

1 9 V Alkaline Battery

1 User Manual

1 Carrying Case

If any of the items are damaged or missing, return the

complete package to the place of purchase for an exchange.

4

INTRODUCTION

The TIC 300 PRO safely checks for the presence of AC

voltage without making any disconnection in cables,

wall sockets, fuses, circuit breakers, junction boxes, etc.

No current flow is needed for correct operation.

Rugged and reliable for utility, industrial and mine safety

applications, the TIC 300 PRO warns against dangerous

voltages in low and medium voltage applications up to

122 KV without contacting the energized conductor.

Features

• Utility tool for checking transmission lines, power

distribution equipment, down power lines, fuses,

and load break connectors

• Lower voltage setting for checking voltage

presence in breaker panels, breakers, power

outlets and wiring

• Verifies presence of voltage from 30 VAC to

122,000 VAC (122 kV)

• Non-contact AC voltage detection

• Visual and audible voltage indication

•

Self-test for verifying that the tester is working properly

• Ergonomic design with a convenient handle

• Drop proof up to 6 ft (1.83 m)

Use with the Hot Stick 410A when voltage exceeds 1500 V

5

OPERATION

ON/OFF Button

When the TIC 300 PRO is activated, the blue LEDs and

beeper will pulse at a slow rate about twice a second.

The red LED of the range (HIGH) will turn ON.

TEST Button

The TEST button should be used prior to testing actual

power circuits. The TEST function will cause the blue

LEDs and beeper of the range selected (LOW or HIGH) to

pulse at a fast rate.

OSHA listed clearance distances for working with

voltage. National or local requirements may be

different.

Line voltage (kV) Phase to ground Phase to phase

phase to phase (ft-in) (m) (ft-in) (m)

0.03 to 1.0 Note1 Note1 Note1 Note1

1.1 to 15.0 2-1 0.64 2-2 0.66

15.1 to 36.0 2-4 0.72 2-7 0.77

36.1 to 46.0 2-7 0.77 2-10 0.77

46.1 to 72.5 3-0 0.90 3-6 1.05

72.6 to 121 3-2 0.95 4-3 1.29

Note1 – No contact necessary

�Caution: If a three phase circuit is being checked and

one phase is open, the voltage from another phase

maybe detected and will give a faulty indication. Always

make sure that the phase cables are separated by at least

20 in (50.8 cm).

6

Voltage Detection

LOW Range

1. Push the ON/OFF push button to turn the unit ON.

2. The high voltage detection circuit is activated. A

beep will sound and the blue LEDs will flash twice

per second.

3. Push the LOW range push button. The unit is ready

for low voltage detection.

4. Place the probe tip of the TIC 300 PRO near, but not

touching, a low (<1000 V) voltage line (Fig. 1).

5. If voltage is present, the blue LEDs will blink and the

beeper will sound at an increased rate. Continuous

visual (blue LEDs) and audible indicators will increase

when the probe tip makes contact with or is very

close to the voltage line.

Fig. 1 Voltage detection in a line

HIGH Range (HOT STICK must be used)

(See Fig. 2)

1. Push the ON/OFF push button to turn the unit ON.

2. The high voltage detection circuit is activated. A

beep will sound and the blue LEDs will flash twice

per second.

3. Approach the probe tip near, but not touching, a

high voltage (>1500 V and <122 kV) conductor.

7

4. If voltage is present, the blue LEDs will blink and the

beeper will sound at an increased rate. Continuous

visual (blue LEDs) and audible indicators will increase

when the probe tip makes contact with or is very

close to the high voltage line.

TIC 300 PRO

Fig. 2 Voltage detection in transmission lines

Locate breaks in insulated wire and heating

elements (See Fig. 3)

1. Push the ON/OFF push button to turn the unit on.

2. Push the LOW range push button.

3. Make sure the wire or the heating element is energized.

4. Place the tip of the probe near the wire and start

tracing along it. When the fast or continuous beeping

stops, the point of the break or “open” is indicated.

HOT STICK

8

Fig. 3 Finding a break/open

Check Outlets and Switches (See Figs. 4 & 5)

1. Push the ON/OFF push button to turn the unit on.

2. Push the LOW range push button.

3. Place the probe tip of the TIC 300 PRO against the

hot prong of an outlet or switch contact.

4. Increased beeping indicates higher voltage presence.

ON

OFF

Fig. 4

Detecting voltage in an

outlet (Note: disconnect

all power cords from the

outlet before testing)

Fig. 5

Finding a breaker

9

MAINTENANCE AND REPAIR

If there appears to be a malfunction during the

operation of the voltage detector, the following steps

should be performed in order to isolate the cause of the

problem:

1. Check the battery.

2. Review the operating instructions for possible

mistakes in operating procedure.

Except for the replacement of the battery, repair of

the voltage detector should be performed only by a

Factory Authorized Service Center or by other qualified

instrument service personnel.

Cleaning

The front panel and case can be cleaned with a mild

solution of detergent and water. Apply sparingly with a

soft cloth and allow to dry completely before using. Do

not use aromatic hydrocarbons or chlorinated solvents

for cleaning.

Battery Replacement

Use a Phillips blade screwdriver to remove the battery

hatch screw. Lift the hatch. Remove the battery and

replace it with a 9 V alkaline battery. Make sure the seal

is in place. Close the battery hatch and replace the screw.

10

SPECIFICATIONS

Operating voltage

LOW Range: 30 to 1500 VAC; HIGH Range: 1500 VAC to

122 kVAC

Operating Temperature: 0°C to +52°C (32°F to +125°F);

RH < 90%

Storage Temperature: 0°C to +52°C (32°F to +125°F)

battery removed

Environment: < 2000 m (1.24 mi), outdoor operation

Power: 9 V alkaline battery

Power Consumption:

• OFF: 60 uA

• Low Detection mode: 39 mA

• High Detection mode: 39 mA

Duty Cycle: Continuous

Frequency Response: 50/60 Hz

Response Time: Instantaneous

Dimensions: 345(L) x 75(W) x 47(H) mm (13.5 x 3.0 x 1.8 in)

Weight: 243 g (0.5 lb)

Optional Accessory: TIC 410A Hot Stick

Electromagnetic Compatibility (EMC): EN 61326-1

Korea (KCC): Class A Equipment (Industrial Broadcasting

& Communication Equipment)

[1]

This product meets requirements for industrial (Class

A) electromagnetic wave equipment and the seller or

user should take notice of it. This equipment is intended

for use in business environments and is not to be used

in homes.

11

Sensitivity: LOW Voltage

Hold the TIC 300 PRO when making the detection range

measurement for LOW voltage range.

Voltage

(Phase to neutral with

890K Ohm load)

Detection Range

(From the TIP of probe to

the target line)

Average

30 V 3.8 cm (1.5 in)

75 V 16.5 cm (6.5 in)

100 V 21.6 cm (8.5 in)

120 V 25.4 cm (10 in)

220 V 33 cm (1 ft 1 in)

500 V 48.3 cm (1 ft 7 in)

1000 V 86.4 cm (2 ft 10 in)

Sensitivity: HIGH Voltage

The TIC 410A Hot Stick must be used when making

detection range measurement for HIGH voltage range.

Voltage

(Open Phase with no load)

Detection Range

(From the TIP of probe to

the target line)

Average

1.5 kV 12.7 mm (0.5 in)

2.0 kV 25.4 mm (1 in)

4.0 kV 5.1 cm (2 in)

10.0 kV 20.3 cm (8 in)

15.0 kV 35.6 cm (1 ft 2 in)

20.0 kV 50.8 cm (1 ft 8 in)

25.0 kV 66 cm (2 ft 2 in)

TIC 300 PRO

TIC Tracer haute tension –

Détecteur de tensions

alternatives sans contact

Mode d’emploi

10/2019, Rev006

Français

Limites de garantie et de responsabilité

Amprobe garantit l’absence de vices de matériaux et de

fabrication de ce produit pendant une période d’un an prenant

effet à la date d’achat. Cette garantie ne s’applique pas aux

fusibles, aux piles jetables ni à tout produit mal utilisé, modifié,

contaminé, négligé ou endommagé par accident ou soumis

à des conditions anormales d’utilisation et de manipulation.

Les revendeurs n’ont pas l’autorisation de prolonger toute autre

garantie au nom d’Amprobe. Pour bénéficier de la garantie,

renvoyez le produit accompagné d’un justificatif d’achat

auprès d’un centre de services agréé par Amprobe Test Tools ou

d’un distributeur ou d’un revendeur Amprobe. Voir la section

Réparation pour tous les détails. LA PRESENTE GARANTIE EST

LE SEUL ET EXCLUSIF RECOURS DE L’UTILISATEUR. TOUTES

AUTRES GARANTIES, EXPLICITES, IMPLICITES OU STATUTAIRES,

NOTAMMENT LES GARANTIES DE QUALITE MARCHANDE OU

D’ADAPTATION A UN OBJECTIF PARTICULIER SONT EXCLUES

PAR LES PRESENTES. LE FABRICANT NE SERA EN AUCUN CAS

TENU RESPONSABLE DE DOMMAGES PARTICULIERS, INDIRECTS,

ACCIDENTELS OU CONSECUTIFS, NI D’AUCUNS DEGATS OU

PERTES DE DONNEES, SUR UNE BASE CONTRACTUELLE, EXTRA-

CONTRACTUELLE OU AUTRE. Etant donné que certaines

juridictions n’admettent pas les limitations d’une condition

de garantie implicite ou l’exclusion ou la limitation de dégâts

accidentels ou consécutifs, il se peut que les limitations et les

exclusions de cette garantie ne s’appliquent pas à votre cas.

Réparation

Tous les outils de test renvoyés pour être réparés au titre de la

garantie doivent être accompagnés des éléments suivants : nom,

raison sociale, adresse, numéro de téléphone et justificatif d’achat.

Ajoutez également une brève description du problème ou du

service demandé et incluez les cordons de test avec l’appareil.

Les frais de remplacement ou de réparation hors garantie doivent

être acquittés par chèque, mandat, carte de crédit avec date

d’expiration, ou par bon de commande payable à l’ordre de

Amprobe

®

Test Tools.

Remplacements et réparations sous garantie – Tous pays

Veuillez lire la déclaration de garantie et vérifiez la pile avant

de demander une réparation. Pendant la période de garantie,

tout outil de test défectueux peut être renvoyé auprès de votre

distributeur Amprobe

®

Test Tools pour être échangé contre un

produit identique ou similaire. Consultez la section « Where to

La pagina sta caricando ...

Amprobe TIC 300 PRO Non-Contact Voltage Detector Manuale utente

Amprobe TIC 300 PRO Non-Contact Voltage Detector Manuale utente

in altre lingue

Documenti correlati

Altri documenti