RCF EVOX JMIX8 Manuale utente

Marca: RCF

Modello: EVOX JMIX8

Categoria: Attrezzatura musicale

Tipo: Manuale utente

OWNER MANUAL

MANUALE D’USO

EVOX JMIX8

- PROFESSIONAL ACTIVE

TWO-WAY ARRAY

WITH INTERNAL DIGITAL MIXER

- DIFFUSORE ACUSTICO (“ARRAY”)

AMPLIFICATO A DUE VIE

CON MIXER DIGITALE INTEGRATO

TABLE OF CONTENTS

INDICE

ENGLISH

ITALIANO

ENGLISH

IMPORTANT

Before connecting and using this product, please read this instruction manual carefully and

keep it on hand for future reference.

The manual is to be considered an integral part of this product and must accompany it when

it changes ownership as a reference for correct installation and use as well as for the safety

precautions.

RCF S.p.A. will not assume any responsibility for the incorrect installation and / or use of this

product.

WARNING: To prevent the risk of ﬁre or electric shock, never expose this product to rain or

humidity.

SAFETY PRECAUTIONS

1. All the precautions, in particular the safety ones, must be read with special attention, as

they provide important information.

2. POWER SUPPLY FROM MAINS

- Appliance coupler or PowerCon Connector® is used to disconnect device from MAIN

power. This device shall remain readily accessible after the installation

- The mains voltage is sufﬁciently high to involve a risk of electrocution: never install or

connect this product when its power cord is plugged in.

- Before powering up, make sure that all the connections have been made correctly and the

voltage of your mains corresponds to the voltage shown on the rating plate on the unit, if

not, please contact your RCF dealer.

- The metallic parts of the unit are earthed by means of the power cord.This is a Class I

device and for its use it must be connected to a grounded power source.

- Protect the power cord from damage. Make sure it is positioned in a way that it cannot be

stepped on or crushed by objects.

- To prevent the risk of electric shock, never open this product: there are no parts inside that

the user needs to access.

3. Make sure that no objects or liquids can get into this product, as this may cause a short

circuit. This apparatus shall not be exposed to dripping or splashing. No objects ﬁlled with

liquid (such as vases) and no naked sources (such as lit candles) should be placed on this

apparatus.

4. Never attempt to carry out any operations, modiﬁcations or repairs that are not expressly

described in this manual.

Contact your authorized service centre or qualiﬁed personnel should any of the following

occur:

- The product does not function (or functions in an anomalous way).

- The power cord has been damaged.

- Objects or liquids are inside the product.

- The product has been subject to a heavy impact.

5. If this product is not used for a long period, disconnect its power cord.

6. If this product begins emitting any strange odours or smoke, switch it off immediately and

disconnect its power cord.

7. Do not connect this product to any equipment or accessories not foreseen.

Do not try to hang this product by using elements that are unsuitable or not speciﬁc for this

purpose.

To prevent the risk of falling equipment, do not stack multiple units of this product unless this

possibility is speciﬁed in the user manual.

IMPORTANT

WARNING

SAFETY PRECAUTIONS

ENGLISH

8. RCF S.p.A. strongly recommends this product is only installed by professional qualiﬁed

installers (or specialised ﬁrms) who can ensure correct installation and certify it according to

the regulations in force.

The entire audio system must comply with the current standards and regulations regarding

electrical systems.

9. Supports and trolleys

The equipment should be only used on trolleys or supports, where necessary, that are

recommended by the manufacturer. The equipment / support / trolley assembly must be

moved with extreme caution.

Sudden stops, excessive pushing force and uneven ﬂoors may cause the assembly to overturn.

10. Hearing loss

Exposure to high sound levels can cause permanent hearing loss. The acoustic pressure level

that leads to hearing loss is different from person to person and depends on the duration

of exposure. To prevent potentially dangerous exposure to high levels of acoustic pressure,

anyone who is exposed to these levels should use adequate protection devices.

When a transducer capable of producing high sound levels is being used, it is therefore

necessary to wear ear plugs or protective earphones. See the manual technical speciﬁcations

to know the maximum sound pressure level.

11. Situate this product far from any heat sources and always ensure adequate air circulation

around it.

12. Do not overload this product for a long time.

13. Never force the control elements (keys, knobs, etc. ).

14. Do not use solvents, alcohol, benzene or other volatile substances for cleaning the

external parts of this product.

Use a dry cloth.

15. Do not put microphones close and in front of speakers, in order to avoid audio feedback

(‘Larsen effect’).

To prevent the occurrence of noise on microphone / line signal cables, use screened cables

only and avoid putting them close to:

- Equipment that produces high-intensity electromagnetic ﬁelds.

- Mains cables.

- Loudspeaker lines.

The equipments considered in this manual can be used in electromagnetic

environment E1 to E3 as speciﬁed on EN 55103-1/2: 2009.

Note: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy, and if it is not installed and used in accordance with the instruction manual, it

may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at his own expense.

Modiﬁcations: Any modiﬁcations made to this device that are not approved by RCF may

void the authority granted to the user by the FCC to operate this equipment.

NOTES ABOUT AUDIO SIGNAL CABLES

FCC RULES

ENGLISH

RCF S.P.A. THANKS YOU FOR PURCHASING THIS PRODUCT, WHICH HAS BEEN

MADE TO GUARANTEE RELIABILITY AND HIGH PERFORMANCE.

DESCRIPTION

EVOX JMIX8 is a portable active sound system (made of a satellite plus a subwoofer) that

combines quality and reliability of RCF transducers with high ampliﬁcation power.

It features eight 2.0” full range transducers in the line source satellite and a deep sounding

12” woofer in a bass reﬂex enclosure.

INTERNAL 8 CHANNEL DIGITAL MIXER

Taking the EVOX J8 one step further, RCF has added an 8-input Digital Mixer to the system.

The onboard processing power of the innovative Z.CORE DSP provides not only full mix

functions it includes high-quality instrument FX and AMP simulations. An EVOX iOS/

Android-compatible app allows to manage the JMIX8. Adding Bluetooth audio and Hi-Z

instrument input, the EVOX JMIX8 combines the quality and reliability of RCF transducers

and ampliﬁcation with a powerful remote controllable 8-channel digital mixer.

The system is an optimal portable solutions for live music, DJ mix-sets and also presentations,

congresses, other events, etc. .

INNOVATIVE DSP PROCESSING

EVOX DSP processing is the result of many years of experience in line array design

combined with innovative and dedicated algorithms. Thanks to the frequency dependent

drivers excursion and control of distortion, EVOX DSP processing is capable to guarantee

a high output from these small systems. A dedicated vocal processing has been speciﬁcally

studied for speech reproduction during presentations or conferences.

RCF TECHNOLOGY

EVOX JMIX8 includes high technology RCF transducers.

The ultra-compact full-range 2” driver can handle extremely high sound pressure levels and

power. The high excursion woofers are able to extend to the lowest frequencies and offer

a quick and precise response up to the crossover point.

Speciﬁc attention has been dedicated to mid-low frequencies as well.

CONTROLLED DIRECTIVITY PATTERN

EVOX array design features a constant horizontal directivity coverage of 120°,

offering a perfect listening experience to the audience.

The vertical array design is progressively shaped to guarantee a correct

listening from the ﬁrst row.

MULTIFUNCTIONAL TOP HANDLE

The top steel plate joins the handle and the insert for pole mounting.

A rubber hand grip has been added for great portability.

CLASS D AMPLIFICATION

EVOX J8 includes a high power two-way class D ampliﬁer with DSP controlled

crossover.

ENGLISH

Remove the rubber band and take out the

satellite

Screw the lower part of the satellite speaker

stand (the pole) into the subwoofer insert for

pole mounting.

Screw the telescopic upper part of the satellite

speaker stand into its lower part.

Loose the stand bolt, adjust the satellite

speaker height from the ﬂoor and tighten the

bolt again, then insert the satellite speaker

into its complete stand and aim it correctly.

INSTALLATION

ENGLISH

SUBWOOFER REAR PANEL

AND CONNECTIONS

Balanced audio input (female XLR connector)

Link output - Stereo Output (male XLR connector).

This output is linked in parallel with the audio input and is useful to connect another

speaker (only when the INPUT FROM MIXER

LED is off). Otherwise it works by

default as the mixer “R” output channel.

System volume control

INPUT FROM MIXER

When the LED is OFF, the digital mixer is disabled and the signal input is coming from the

XLR input

. In this case the male XLR output works as a regular parallel audio output.

When the LED is ON, the signal input is coming from EVOX JMIX8 digital mixer. In this

case, the male XLR output becomes by default the R output to an addictional EVOX J8.

(The mixer offers a function (SWAP LR) to swap the L-R output channels swapping them

to “R-L”;

See section 11 on the Digital Mixer Instruction Chapter).

FLAT / BOOST switch

FLAT (released switch, normal mode): no equalisation is applied (ﬂat frequency

response).

BOOST (pushed switch): ‘loudness’ equalisation, only recommended for background

music at low volume levels.

LIMITER LED

The internal ampliﬁer is provided with a limiter circuit to prevent clipping and overdriving

transducers. It blinks when the signal level reaches the clipping point, causing the limiter

intervention. If it is steady lit, the input signal level is excessive and should be reduced.

SIGNAL LED

When lit, it indicates the signal presence at the audio input.

STATUS LED

When blinking, it indicates the internal protection intervention due to thermal drift (the

ampliﬁer then gets to a “mute” status).

Female XLR connector

PUSH

2 1

Male XLR connector

XLR pins:

1 gRound, 2 audio signaL (+ , hot),

3 audio signaL (–, coLd).

PUSH

2 1

ENGLISH

Ampliﬁer output to link the satellite speaker.

POWER switch

Push it to turn ON / OFF the ampliﬁer.

Before switching the ampliﬁer ON, check all the connections and turn fully

counterclockwise (– ∞) the volume control

VDE Inlet with fuse.

100-120V~ T 6.3 A L 250V

220-240V~ T 3.15 A L 250V

Before connecting the power cord, check if the A/C Power corresponds to the voltage

indicated on the rating plate on the unit. If not, please contact your RCF dealer.

Connect the power cord only to a A/C Power socket outlet with a protective earthing

connection.

When replacing the fuse, refer to the silkscreen indications.

WARNING: the VDE Power Connector is used to disconnect the system from the power

supply network. It must be always easily accessible after the installation and during the

use of the system.

10 11

ENGLISH

IMPORTANT:

befORe TuRNINg The AMPlIfIeR ON, lINk The

subwOOfeR AMPlIfIeR OuTPuT TO The sATellITe

sPeAkeR INPuT (As shOwN IN The fIguRe)

ENGLISH

MIC/LINE Combo inputs 1 and 2 are provided with switchable 48V Phantom Power;

connect here microphones (XLR) or line sources (TRS jack). It is possible to connect here

Condenser or Electret microphones thanks to the available 48V phantom power.

MIC/LINE Combo inputs 3 and 4; connect here dynamic microphones (XLR) or line

sources (TRS jack).

HiZ LINE input. LINE input 4 is provided with selectable Hi Impedance input, which

offers optimum reproduction of a guitar or bass guitar even if with passive pick up. The

instrument connected to Line input 4 can take advantage of the MFX section (see section

16 of this manual).

Stereo Line input 5 and 6; connect a stereo line source to these TS Jack pair. If

connected alone the input line 5(L) behaves like a mono input.

Stereo Line input 7 and 8; connect a low level (-10dBV) stereo line source to these

RCA unbalanced inputs.

Footswitch; it allows usage of a dual footswitch, one function can be assigned on the

tip contact and one to the ring contact. Find all the possible assignable function in the

section 16 of the mixer surface description.

AUX OUT; this is a balanced output for the auxiliary send available on each input

channel.

ONBOARD DIGITAL MIXER

INSTRUCTIONS

INPUT PANEL

ENGLISH

DISPLAY MENU INFORMATION

All the functions available on the EVOX JMIX8 system integrated mixer can be operated

from the operating display.

The select buttons: INPUT, OUTPUT, HOME, SYSTEM, MFX, FX give access to all the

parameter pages on the LCD display.

Navigate into the display menu by pressing the PARAMETER SELECT buttons (12) to

select the parameters to edit, and rotate the EDIT encoder [

] to change those values.

Some settings require a push of EDIT encoder to conﬁrm value or function change, and a

display message will appear in this eventuality.

All display pages are usefully shown in the panel silkscreen:

FRONT PANEL

ENGLISH

MONO input channels; the MIC/LINE 1 to 4 input channels provide a level knob and

an INPUT button. The small yellow point named 0dB indicates the “unity gain” level

of the channel. The SIGNAL LED lights up in green when a signal louder than -40dB is

applied to the input. The red LED located between the channels 1 and 2 knobs indicates

that the +48V phantom power is activated on those channels (see section 16). Pressing

the HOME button (15) the METER page will open showing the level metering of signal

inputs and outputs. The INPUT button, repeatedly pressed, gives access to the four

available display parameters pages (14). The number on the display upper left corner

indicates which input channel is being edited.

INPUT Menus for mono channels:

Page LVL

LEVELS (LVL): this menu page gives access to FX send and AUX send levels for the

speciﬁed input. PAN and channel MUTE controls are shown on the right side. The small

rectangular boxes on the bottom line, from left to right, indicate the absolute levels of FX

send, AUX send and Channel Level.

FRONT PANEL

ENGLISH

Page EQ

EQUALIZATION (EQ): this menu page gives access to EQ parameters; every input channel

is provided with a three band EQ: LOW and HIGH bands are +/-12dB shelving EQs

with reference frequency at 125Hz and 6.0kHz. The MID BAND EQ provide selectable

frequency from 50Hz to 12kHz and +/-12dB gain. A global EQ ON/OFF control is

available on the lower right.

Page PRE

PREAMP GAIN (PRE): an input GAIN parameter allows to add up to 30dB to the input

signal. HPF performs a selectable High Pass Filter from 20Hz to 1kHz. INV ON/OFF

permits to invert the polarity of the input signal. In the channel 1 and 2 PRE pages a

dedicated box indicates the activation of +48V phantom power (see section 16).

Page DYN

DYNAMIC (DYN): COMPRESSOR; MIC/LINE inputs 1 to 4 are provided with a single

control compressor. The cursor indicates the depth of the compressor intervention. A

dedicated box toggles the compressor ON and OFF. Up to 6 different presets can be

selected from the Compressor Model list:

1. LIGHT

2. HEAVY

3. VOCAL

4. BASS

5. ACOUSTIC

6. DRUM

LINE input 4 is provided with selectable Hi Impedance input, which is available for

passive instruments such as guitars or bass guitars. The instrument connected to Line

input 4 can also take advantage of the MFX section (see dedicated chapter 17). Page PRE

for LINE input 4 changes slightly:

Ch.4 LINE IN Page PRE

A dedicated box, labeled HI-Z, allows to activate and deactivate the High Impedance

input on LINE 4: HI-Z ON/OFF.

ENGLISH

STEREO LINE input channel 5/6: connect to these TS jacks any analog stereo source.

Control the stereo channel level with the dedicated knob: The SIGNAL LED lights up in

green when a signal louder than -40dB is applied to the input. Pressing the INPUT button

gives the access to display menus:

Page LVL

LEVELS (LVL): as for the MONO channels, this menu page gives access to the channel FX

send, AUX send. BAL (balance) and channel MUTE controls are shown on the right side.

When pressed, the MUTE button also affects FX and AUX sends. The small rectangular

boxes on the bottom line, from left to right, indicate the absolute levels of FX send, AUX

send and Channel Level. All the other pages are same as MONO channels input.

STEREO LINE 7/8: connect to these RCA connectors any low level analog stereo

source (-10dBV). Control the stereo channel level with the dedicated knob: the SIGNAL

LED lights up in green when a signal louder than -40dB is applied to the input. Pressing

the INPUT button gives the access to display menus. The control pages of channels 7/8

are same as channel 5/6 except for the PRE page:

From the dedicated box called DUCKER it is possible to activate a ducker gate on

channels 7/8. The control key for the ducker is always the signal present on MIC input 1.

Channel 7/8 is also used for Bluetooth audio input.

MAIN LEVEL: MAIN LEVEL controls the master signal level; it provides a control level

knob and an OUTPUT button. The small yellow point named 0dB indicates the “unity

gain” level of the Main Mix. Press the button HOME (15) to show the METER page which

includes level metering of L-R output. Pressing the OUTPUT button gives access to the

following pages:

OUT page: in this page a drop down menu shows one of the four selectable mastering

presets. Rotate and press the EDIT encoder to select a different mastering preset:

1. MASTERING

2. MASTER BOOST

3. LOUD & PROUD

4. HI-FI

These presets combine the action of an Exciter and a Maximizer to apply nice dynamic

and frequency response improvement to the Master signal.

A dedicated box MP ON/OFF permits to turn on and off this feature.

The STEREO box ON/OFF allows to select the chosen system conﬁguration: using the

EVOX JMIX8 as a stand alone speaker, the STEREO box has to be set to OFF. Using EVOX

8 JMIX8 + EVOX J8 as a stereo conﬁguration, the STEREO BOX has to be set to ON. In

ENGLISH

this case the EVOX JMIX8 outputs the LEFT channel and the EVOX J8 outputs the RIGHT

channel. If the environment or the setup does not permit the correct positioning of EVOX

JMIX8 as left channel and EVOX J8 as right channel, it is possible to reverse the stereo

image using the box called SWAP LR:

SWAP LR OFF: EVOX JMIX8 LEFT – EVOX J8 RIGHT

SWAP LR ON: EVOX JMIX8 RIGHT – EVOX J8 LEFT

A MUTE box completes the set of controls on this page. Selecting the MUTE box

interrupts the signal ﬂow through the MAIN stereo channel. The numeric window in the

lower right display corner shows the nominal level of the MAIN LEVEL knob. The small

round point on the knob scale indicates the 0.0dB level.

MAIN GEQ page: this page gives access to the 7 band Graphic EQ available on MAIN

channel. Select each single band of the EQ using the “PARAMETER SELECT” buttons

[

] and rotate the EDIT encoder to change value. A value box shows the variation in dBs

of the selected band. A dedicated box permits to turn ON and OFF the entire EQ.

AUX OUT page: this page gives access to the master level control of the AUX bus with

a dedicated graphic fader. L+R ON/OFF box permits to assign the MAIN MIX signal,

summed in mono, to the AUX bus. PRE/POST ON/OFF box allows to derive the AUX signal

before or after the channel level control.

Set this control to OFF for AUX PRE and ON for AUX POST. FX RTN ON/OFF box permits

to assign the internal effect return to the AUX bus. The MUTE box, if selected, mutes the

AUX bus output.

AUX GEQ page: this page gives access to the 7 band Graphic EQ available on AUX bus.

Select each single band of the EQ using the “PARAMETER SELECT” button and rotate

the EDIT encoder to change value. A value box shows the variation in dBs of the selected

band. A dedicated box permits to turn ON and OFF the entire EQ.

HOME Button:

The HOME button gives access to three pages: MTR Page, INFO Page and “I/0” Page.

MTR page: on the METER page it’s possible to view all the mixer signal levels: Inputs

from 1 to 8, AUX and MAIN L/R.

ENGLISH

Pressing the HOME button again gives access to the INFO page where the following is

shown:

FIRMWARE: ﬁrmware version - x.xx

BT ID: Bluetooth Identiﬁcation – 123x

BT STAT: Bluetooth status - (OFF/PAIRING/ONLINE)

USB STAT: USB connection status - (OFFLINE/ONLINE)

Pressing the HOME button again gives access to the “I/0” MIXER ENABLE DISABLE page.

This menu allows to disable the mixer in an EVOX JMIX8 system. Turn the EDIT encoder

counterclockwise to change the menu line from MIXER ENABLE to MIXER DISABLE, press

the EDIT encoder, a display message will appear:

DISABLE MIXER – PRESS ENCODER TO CONFIRM – PRESS ANY KEY TO CANCEL

By pressing the EDIT encoder again, the mixer is disabled and the LCD display backlight

will switch off in 3 seconds.

Now the mixer is disabled, and the EVOX JMIX8 can be used like a conventional active

speaker using the XLR connection located on the subwoofer back panel as mono input.

To enable the mixer again, turn clockwise the EDIT encoder, the display will switch on

again, press the EDIT encoder and a display message will appear:

ENABLE MIXER – PRESS ENCODER TO CONFIRM – PRESS ANY KEY TO CANCEL

Pressing the EDIT encoder the EVOX JMIX8 mixer is enabled again and the system turns

to full operation.

SYSTEM button:

Pressing the button once gives access to the LOAD SHOW page;

ENGLISH

It is possible to load a pre-saved SHOW from the dedicated menu. A SHOW preset includes

all the mixer parameters except the INPUT and MAIN level. These parameters are absolute

values and can be controlled via pot knobs only. The possible selection is between 10

presets (01 to 10) plus a special preset n°11 called RESET MIXER. Loading the RESET

MIXER preset brings the mixer to a default setting.

To load a preset rotate the EDIT encoder clockwise, select the chosen preset and conﬁrm

the selection pressing the EDIT encoder. A message will appear:

LOAD PRESET “XX” – PRESS ENCODER TO CONFIRM - PRESS ANY KEY TO CANCEL

Press the EDIT encoder again to load the selected preset, or press any key to cancel the

operation.

When a preset is loaded, this information will appear in a dedicated area on the LOAD

SHOW page.

SAVE SHOW page:

The SAVE SHOW page permits to save all the parameters of the mixer in a preset. Again,

the INPUT and MAIN level are excluded from the preset data, they are absolute values and

can be controlled via pot knobs only.

Select a preset location from the dedicated menu rotating the EDIT encoder, then press the

EDIT encoder; a display message will appear:

ENGLISH

SAVE PRESET “XX” – PRESS ENCODER TO CONFIRM - PRESS ANY KEY TO CANCEL

By pressing the EDIT encoder, the preset will be stored. If the selected preset is already in

use a message will appear:

OVERWRITE PRESET “XX” – PRESS ENCODER TO CONFIRM - PRESS ANY KEY TO

CANCEL

By pressing the encoder again will store the preset, while pressing any key will cancel the

operation.

By pressing the SYSTEM button once more, the SET page is shown:

The SET page allows to access to some important mixer settings.

The boxes from top left to bottom:

+48V ON/OFF: enables or disables +48 V phantom power on MIC inputs 1 and 2.

BLUETOOTH ON/OFF: enables or disables the Bluetooth connection both for audio

streaming and control.

STARTUP DEFAULT ON/OFF: if this box is set to OFF when the system is switched on, the

mixer keeps its last status when turned off. If the box is set to ON, the mixer is switched

on with a default conﬁguration.

The BACKLIGHT and CONTRAST boxes permit to set brightness and contrast of the LCD

display.

Pressing the SYSTEM button again gives access to the FSW page dedicated to assign

footswitch functions (see section 6 in the input panel description).

FSW page:

The FSW page is composed of three menus: TIP FUN, RING FUN, POLARITY

1. TIP FUN (Tip jack contact function) including:

- MUTE OUTS

- FX ON/OFF

- MFX CHAN A/B

- MFX ON/OFF

- MFX AMP ON/OFF

- MFX MOD ON/OFF

- MFX DLY ON/OFF

- SHOW NEXT

- SHOW PREV

- MASTER PROC ON/OFF

ENGLISH

2. The RING FUN (Ring function) provides the same selections as for TIP FUN menu.

3. A POLARITY menu allows to change the initial status of the connected footswitch

between NORMALLY CLOSED and NORMALLY OPEN.

MFX button:

The MFX button controls the menu related to the MFX chain present on LINE input 4.

Two local settings of the whole MFX are available, called Channel A and B. It is possible

to switch between A and B using the footswitch (see dedicated function).

The SET page allows to select between FX channel A or B with the dedicated knob icon.

MFX ON/OFF box allows to turn on and off the MFX chain. The AMP, MOD, DLY ON/

OFF boxes located in the bottom line of the display turn on and off individually the

components of the MFX chain:

AMP (Guitar & Bass amp simulator), MOD (modulations effects), DLY (delay).

Pressing the MFX button again gives access to the AMP page:

AMP page: using the AMP MODEL menu on the bottom of the display, it is possible to

select one of the 15 amp simulations by OVERLOUD

1. DARKFACE ‘65

2. JAZZ C

3. ROCK’64

4. ROCK 800

5. ROCK 900

6. TOP 30

7. MODERN

8. BASSAMP

9. BASSMATE

10. MARKBASS 1

11. MARKBASS 2

12. SLO 88 CRUNCH

13. SLO 88 LEAD

14. OVERANGE 120

15. HEAVY 51

Rotate the EDIT encoder to select an AMP Simulation model.

The top line of rotary controls allows to change the parameters of the selected AMP

model: DRV (Drive), BASS (Bass frequencies), MID (Mid frequencies), TRB (Treble-High

frequencies).

The AMP ON/OFF box allows to bypass the amp simulator.

Press MFX again to access to MOD page:

MOD page: use the MOD. PRESET menu on the bottom of the page to select a

modulation program between:

1. CHORUS

ENGLISH

2. FLANGER

3. TREMOLO

Rotate the EDIT encoder to select a modulation type.

The two rotary controls allow to change the parameters of the selected modulation

preset: DEP (Depht) from 0 to 100%, and RATE (rate) in Hz.

The MOD ON/OFF box allows to bypass the modulation module.

DLY page:

The Delay page shows three rotary controls to edit the DELAY effect: LEV (level), TIME

(Delay time) in ms, FDBK (Delay feedback). Set these parameters to create the favorite

delay effect. The DLY ON/OFF box allows to bypass the delay module.

FX button:

Pressing the FX button gives access to the internal effects edit page.

FX PRESET menu allows to select the FX presets:

01 – 40 – REVERBS 41 – 60 – DELAYS

61 – 80 – MODULATIONS

Select a preset rotating the EDIT encoder and conﬁrm the selection pressing it. The ON/

OFF box permits to switch the effect send (FX) on and off.

Each program shows two editable parameters and an effect return level control. The

editable parameters for REV programs are:

DEC (sec) – Decay in seconds

DAMP – Frequency Damping

For DLY programs:

TIM (ms) – time in milliseconds

FDBK – Feedback

For MOD programs:

RATE – rate (in Hz)

DEPTH – depth

PAIR button.

Pressing the PAIR button initiates the Bluetooth discovery sequence, required when a new

pairing operation has to be performed on a smartphone, tablet or notebook. The green

LED will blink as long as a Bluetooth device is associated. When the device is connected,

the green LED will be steadily lit. Now it is possible to control the EVOX JMIX8 system via

the Android or iOS app. Furthermore, a Bluetooth audio streaming is enabled to stereo

channel 7/8 (see section 10 of this chapter)

USB.

The “type B” USB connector is used for future ﬁrmware upgrades.

La pagina sta caricando ...

RCF EVOX JMIX8 Manuale utente

Marca: RCF

Modello: EVOX JMIX8

Categoria: Attrezzatura musicale

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: RCF EVOX JMIX8 User manual

RCF EVOX JMIX8 Manuale utente

RCF EVOX JMIX8 Manuale utente

in altre lingue

Documenti correlati

Altri documenti