Intel D945PSN Manuale utente

Intel® Desktop Board D945PSN

Product Guide

Order Number: D10461-003

Revision History

Revision Revision History Date

-001

First release of the Intel

®

Desktop Board D945PSN Product Guide.

April 2005

-002

Second release of the Intel

®

Desktop Board D945PSN Product Guide.

August 2005

-003

Third release of the Intel

®

Desktop Board D945PSN Product Guide.

April 2006

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user’s authority to

operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the

Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux appareils

numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par le ministére des

Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel

®

products. No license, express or implied, by estoppel or

otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions

of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating

to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,

or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical,

life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time,

without notice.

Desktop Board D945PSN may contain design defects or errors known as errata which may cause the product to deviate

from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product

order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be

obtained from Intel Corporation by going to the World Wide Web site at: http://www.intel.com/ or by calling

1-800-548-4725.

Intel, Pentium, and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other

countries.

* Other names and brands may be claimed as the property of others.

iii

Preface

This Product Guide gives information about board layout, component installation, BIOS update,

and regulatory requirements for Intel

®

Desktop Board D945PSN.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for general

audiences.

Use Only for Intended Applications

All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.) for use in

personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar

locations. The suitability of this product for other PC or embedded non-PC applications or other

environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported

without further evaluation by Intel.

Information Layout

The chapters in this Product Guide are arranged as follows:

1 Desktop Board Features: a summary of product features

2 Installing and Replacing Desktop Board Components: instructions on how to install the desktop

board and other hardware components

3 BIOS: instructions on how to update the BIOS

A Error Messages and Indicators: information about BIOS error messages and beep codes

B Regulatory Compliance: safety and EMC regulations, product certification

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

Intel Desktop Board D945PSN Product Guide

iv

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)

GHz Gigahertz (one billion hertz)

KB Kilobyte (1024 bytes)

MB Megabyte (1,048,576 bytes)

Mbit Megabit (1,048,576 bits)

MHz Megahertz (one million hertz)

Box Contents

• Intel

®

Desktop Board D945PSN

• I/O shield

• One ATA-66/100 cable

• Two locking Serial ATA cables

• One diskette drive cable

• Intel

®

Express Installer Driver CD-ROM

• Intel Express Installer Software CD-ROM

• Quick Reference poster

• Configuration and battery caution statement label

v

Contents

1 Desktop Board Features

Supported Operating Systems ............................................................................................10

Desktop Board Components ...............................................................................................11

Processor............................................................................................................................13

Main Memory ......................................................................................................................14

Intel

®

945P Express Chipset ...............................................................................................15

Graphics Subsystem ...........................................................................................................15

Audio Subsystem ................................................................................................................15

Input/Output (I/O) Controller ................................................................................................16

LAN Subsystem ..................................................................................................................16

LAN Subsystem Software...........................................................................................16

RJ-45 LAN Connector LEDs.......................................................................................16

Hi-Speed USB 2.0 Support..................................................................................................17

Enhanced IDE Interface ......................................................................................................17

Serial ATA...........................................................................................................................17

Expandability.......................................................................................................................18

BIOS ...................................................................................................................................18

Serial ATA and IDE Auto Configuration ......................................................................18

PCI and PCI Express Auto Configuration ...................................................................18

Security Passwords....................................................................................................18

Chassis Intrusion.................................................................................................................19

Power Management Features .............................................................................................19

ACPI...........................................................................................................................19

Power Connectors......................................................................................................19

Fan Connectors..........................................................................................................19

Fan Speed Control (Intel

®

Precision Cooling Technology)..........................................19

Suspend to RAM (Instantly Available PC Technology) ...............................................20

Wake from USB..........................................................................................................21

Wake from PS/2 Keyboard/Mouse..............................................................................21

PME# Wakeup Support ..............................................................................................21

Speaker...............................................................................................................................21

Battery.................................................................................................................................21

Real-Time Clock..................................................................................................................21

2 Installing and Replacing Desktop Board Components

Before You Begin................................................................................................................23

Installation Precautions .......................................................................................................24

Installation Instructions........................................................................................................24

Ensure Electromagnetic Compatibility (EMC) Compliance..........................................24

Chassis and Component Certifications.......................................................................25

Prevent Power Supply Overload.................................................................................25

Place Battery Marking ................................................................................................25

Use Only for Intended Applications.............................................................................26

Installing the I/O Shield .......................................................................................................26

Intel Desktop Board D945PSN Product Guide

vi

Installing and Removing the Desktop Board........................................................................27

Installing and Removing a Processor ..................................................................................28

Installing a Processor .................................................................................................28

Installing the Processor Fan Heat Sink.......................................................................31

Connecting the Processor Fan Heat Sink Cable.........................................................31

Removing the Processor ............................................................................................31

Installing and Removing Memory ........................................................................................32

Installing DIMMs.........................................................................................................34

Removing DIMMs.......................................................................................................35

Installing and Removing a PCI Express x16 Card ...............................................................36

Installing a PCI Express x16 Card ..............................................................................36

Removing the PCI Express x16 Card .........................................................................36

Connecting the IDE Cable...................................................................................................37

Connecting the Serial ATA (SATA) Cable ...........................................................................38

Connecting Internal Headers...............................................................................................39

Installing a Front Panel Audio Solution for Intel

®

High Definition Audio.......................40

Connecting USB 2.0 Headers.....................................................................................41

Connecting IEEE 1394a Headers...............................................................................41

Connecting the Front Panel Header ...........................................................................41

Setting Up the Flexible 6- Channel Audio with Jack Re-tasking..........................................42

Connecting Fan and Power Cables .....................................................................................43

Connecting Fan Cables ..............................................................................................43

Connecting Power Supply Cables ..............................................................................44

Other Connectors................................................................................................................45

Setting the BIOS Configuration Jumper Block .....................................................................46

Clearing Passwords ............................................................................................................47

3 BIOS

Updating the BIOS with the Intel

®

Express BIOS Update Utility...........................................53

Updating the BIOS with the Iflash Memory Update Utility ....................................................54

Obtaining the BIOS Update File..................................................................................54

Updating the BIOS......................................................................................................54

Recovering the BIOS..................................................................................................55

A Error Messages and Indicators

BIOS Beep Codes...............................................................................................................57

BIOS Error Messages .........................................................................................................57

B Regulatory Compliance

Safety Regulations ..............................................................................................................59

European Union Declaration of Conformity Statement ........................................................59

Product Ecology Statements ...............................................................................................61

Lead-Free Desktop Board ..........................................................................................64

EMC Regulations ................................................................................................................65

Product Certification Markings (Board Level) ......................................................................66

Contents

vii

Figures

1. Desktop Board D945PSN Components ........................................................................11

2. LAN Port LED Locations...............................................................................................16

3. Location of Standby Power Indicator.............................................................................20

4. Installing the I/O Shield.................................................................................................26

5. Desktop Board D945PSN Mounting Screw Hole Locations...........................................27

6. Lift Socket Lever...........................................................................................................28

7. Lift the Load Plate and Don’t Touch the Socket Contacts .............................................28

8. Remove the Protective Socket Cover ...........................................................................29

9. Remove the Processor from the Protective Processor Cover/Do Not Touch.................29

10. Install Processor ...........................................................................................................30

11. Close the Load Plate ....................................................................................................30

12. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Connector ........31

13. Dual Configuration Example 1 ......................................................................................32

14. Dual Configuration Example 2 ......................................................................................32

15. Dual Configuration Example 3 ......................................................................................33

16. Installing a DIMM..........................................................................................................34

17. Inserting a PCI Express x16 Card.................................................................................36

18. Connecting the IDE Cable ............................................................................................37

19. Connecting the Serial ATA Cable .................................................................................38

20. Internal Headers ...........................................................................................................39

21. Back Panel Audio Connectors for Flexible 6-Channel Audio System ............................42

22. Location of Fan Headers...............................................................................................43

23. Connecting Power Supply Cables.................................................................................44

24. Location of Other Connectors on Desktop Board D945PSN .........................................45

25. Location of the BIOS Configuration Jumper..................................................................46

26. Removing the Battery ...................................................................................................52

27. F2 Key ..........................................................................................................................53

Tables

1. Feature Summary...........................................................................................................9

2. Desktop Board D945PSN Components ........................................................................12

3. Power Supply Requirements.........................................................................................13

4. Desktop Board D945PSN Memory Configurations........................................................14

5. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs ..........................................17

6. Front Panel Audio Header Signal Names for Intel

®

High Definition Audio .....................40

7. AC ’97 Audio Header Signal Names .............................................................................40

8. USB 2.0 Header Signal Names.....................................................................................41

9. IEEE 1394a Header Signal Names...............................................................................41

10. Front Panel Header Signal Names................................................................................41

11. Jumper Settings for the BIOS Setup Program Modes ...................................................46

12. Beep Codes..................................................................................................................57

13. BIOS Error Messages...................................................................................................57

14. Safety Regulations........................................................................................................59

15. Lead-Free Board Markings ...........................................................................................64

16. EMC Regulations..........................................................................................................65

17. Product Certification Markings ......................................................................................66

Intel Desktop Board D945PSN Product Guide

viii

9

1 Desktop Board Features

This chapter briefly describes the main features of Intel

®

Desktop Board D945PSN. Table 1

summarizes the major features of the desktop board.

Table 1. Feature Summary

Form Factors

ATX (12.00-inches by 9.60-inches)

Processor

Support for an Intel

®

processor in the LGA775 package

Main Memory

• Four 240-pin, 1.8 V SDRAM Dual Inline Memory Module (DIMM) sockets

• 667/533/400 MHz single or dual channel DDR2 SDRAM interface

• Designed to support up to 4 GB of system memory

NOTE: System resources (such as PCI and PCI Express*) require physical

memory address locations that reduce available memory addresses above 3 GB.

This may result in less than 4 GB of memory being available to the operating

system and applications. For the latest list of tested memory, refer to the Intel

World Wide Web site at: http://support.intel.com/support/motherboards/desktop/

Chipset

Intel

®

945P Express Chipset consisting of:

• Intel

®

82945P Memory Controller Hub (MCH) with Direct Media Interface

• Intel

®

82801GB I/O Controller Hub (ICH7)

• Serial Peripheral Interface (SPI) Flash or Firmware Hub (FWH)

Audio

• Intel 945P Express Chipset

• Intel

®

High Definition Audio interface

• SigmaTel* codec

LAN Subsystem

Intel

®

82573V or 82573L Gigabit Ethernet controller with RJ-45 connector

Expansion Capabilities

• Four PCI bus add-in card connectors (SMBus routed to PCI bus 2)

• One PCI Express* x16 connector

• Two PCI Express x1 connector

Peripheral Interfaces

• Up to eight Hi-Speed USB 2.0 ports:

⎯ Four ports routed to the back panel

⎯ Four ports routed to two USB headers

• Up to three IEEE 1394a ports:

⎯ One port routed to the back panel

⎯ Two ports routed to two IEEE 1394a headers

• Four Serial ATA (SATA) channels (3.0 Gb/s), via the ICH7, one device per

channel

• One IDE interface with ATA-66/100 support (two devices)

• One diskette drive interface

• One parallel port

• One serial port

• PS/2* keyboard and mouse ports

continued

Intel Desktop Board D945PSN Product Guide

10

Table 1. Feature Summary (continued)

BIOS

• Intel

®

Platform Innovation Framework for extensible firmware interface

• 4 Mbit symmetrical flash memory

• Support for SMBIOS

• Intel

®

Rapid BIOS Boot

• Intel

®

Express BIOS Update

Power Management

• Support for Advanced Configuration and Power Interface (ACPI)

• Suspend to RAM (STR)

• Wake on USB, PCI, PCI Express, PS/2, LAN, and front panel

Hardware Management Hardware monitor with:

• Three fan sensing inputs used to monitor fan activity

• Remote diode temperature sensing

• Intel

®

Precision Cooling Technology fan speed control

• Voltage sensing to detect out of range values

Related Links:

For more information about Desktop Board D945PSN, including the Technical Product

Specification (TPS), BIOS updates, and device drivers, go to:

http://support.intel.com/support/motherboards/desktop/

Supported Operating Systems

The desktop board supports the following operating systems:

• Microsoft Windows* 2000

• Microsoft Windows XP Professional

• Microsoft Windows XP Professional x64 Edition

• Microsoft Windows XP Home

• Microsoft Windows XP Media Center Edition 2005

Desktop Board Features

11

Desktop Board Components

Figure 1 shows the approximate location of the major components on Desktop Board D945PSN.

E

F

G

H

R

Intel

82945P

(MCH)

Intel

82801

(ICH7R)

R

Channel B DIMM 1

Channel A DIMM 0

Channel A DIMM 1

Channel B DIMM 0

A

BC

T

D

I

J

K

L

M

N

O

P

Q

R

S

1394a

IEEE

Line In

OM17747

Figure 1. Desktop Board D945PSN Components

Intel Desktop Board D945PSN Product Guide

12

Table 2. Desktop Board D945PSN Components

Label Description

A Auxiliary rear chassis fan header 1 (4-pin, fan speed control)

B PCI Express x1 connectors

C Front panel audio header

D PCI Express x16 connector

E 12 V processor core voltage connector (2x2)

F Rear chassis fan header 1 (3-pin, fan speed control)

G Processor socket (LGA775)

H Processor fan header (4-pin, fan speed control)

I Main power connector (2x12)

J Diskette drive connector

K IDE connector

L Front chassis fan header (3-pin, fan speed control)

M BIOS configuration jumper block

N Chassis intrusion header

O Serial ATA connectors

P Front panel header

Q Alternate power LED header

R Hi-speed USB 2.0 headers

S IEEE 1394a headers

T PCI bus add-in card connectors

Related Links:

Go to the following links for more information about:

• Desktop Board D945PSN

http://www.intel.com/design/motherbd

http://support.intel.com/support/motherboards/desktop

• Supported processors

http://support.intel.com/support/motherboards/desktop

• Audio software and utilities

http://www.intel.com/design/motherbd

• LAN software and drivers

http://www.intel.com/design/motherbd

Desktop Board Features

13

Processor

CAUTION

Failure to use the appropriate power supply (below) and/or not connecting the 12 V (2x2) power

connector to the desktop board may result in damage to the board or the system may not function

properly.

Table 3. Power Supply Requirements

Platform Compatibility Guide Power Supply Requirements

05B 12V2 rating of 16 A continuous and 19 A peak current for 10mS

05A 12V2 rating of 13 A continuous and 16.5 A peak current for 10mS

04B or 04A ATX12V (version 2.0 or greater) compliant Power Supply

Desktop Board D945PSN supports an Intel processor in the LGA775 package. Processors are not

included with the desktop board and must be purchased separately. The processor connects to the

desktop board through the LGA775 socket.

The supported processors list for Desktop Board D945PSN is located on the web at:

http://support.intel.com/support/motherboards/desktop/

Related Links:

Go to the following links or pages for more information about:

• Instructions on installing or upgrading the processor, page

28 in Chapter 2

• The location of the two power connectors, page

44 in Chapter 2

Intel Desktop Board D945PSN Product Guide

14

Main Memory

NOTE

To be fully compliant with all applicable Intel

®

SDRAM memory specifications, the board should

be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your

memory modules do not support SPD, you will see a notification to this effect on the screen at

power up. The BIOS will attempt to configure the memory controller for normal operation.

The desktop board supports dual or single channel memory configurations defined in Table 4.

Table 4. Desktop Board D945PSN Memory Configurations

Memory Speed FSB frequency (MHz) Memory Speed (MHz)

1066 667

800 667

DDR2-667

533 533

1066 533

800 533

DDR2-533

533 533

800 400 DDR2-400

533 400

• Four 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline Memory Modules (DIMMs)

connectors with gold plated contacts

• Unbuffered, non-registered single or double-sided DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC RAM

• 1.8 V memory

• Memory configuration listed below:

⎯ Up to 2.0 GB utilizing 256 Mb technology

⎯ Up to 4.0 GB utilizing 512 Mb or 1 Gb technology

NOTE

System resources (such as PCI and PCI Express) require physical memory address locations that

reduce available memory addresses above 3 GB. This may result in less than 4 GB of memory

being available to the operating system and applications.

Related Links:

Go to the following links or pages for more information about:

• The latest list of tested memory,

http://support.intel.com/support/motherboards/desktop/

• SDRAM specifications,

http://www.intel.com/technology/memory/

• Installing memory, page

32 in Chapter 2

Desktop Board Features

15

Intel

®

945P Express Chipset

The Intel 945P Express Chipset consists of the following devices:

• Intel 82945P Memory Controller Hub (MCH) with Digital Media Interface

• Intel 82801GB I/O Controller Hub (ICH7)

• Serial Peripheral Interface (SPI) Flash or Firmware Hub (FWH)

Related Links:

Go to the following link or pages for more information about:

• Audio drivers and utilities

http://support.intel.com/support/motherboards/desktop/

• Installing the front panel audio solution, page

40 in Chapter 2

• Location of the back panel audio connectors, page

42 in Chapter 2

Input/Output (I/O) Controller

The super I/O controller features the following:

• Low pin count (LPC) interface

• One serial port

• One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port

(EPP) support

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• PS/2-style mouse and keyboard interfaces

• Interface for one 1.2 MB or 1.44 MB diskette drive

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

LAN Subsystem

The LAN, with the Intel 82801GB (ICH7), provides the following functions:

• Support for Intel 82573V or 82573L 10/100/1000 Gigabit Ethernet LAN

• Support for RJ-45 connector with status indicator LEDs

• Programmable transit threshold

• Configurable EEPROM that contains the MAC address

LAN Subsystem Software

For LAN software and drivers, refer to the D945PSN link on Intel’s World Wide Web site at:

http://support.intel.com/support/motherboards/desktop

RJ-45 LAN Connector LEDs

Two LEDs are built into the RJ-45 LAN port located on the back panel (see Figure 2).

OM17386

Figure 2. LAN Port LED Locations

Desktop Board Features

17

Table 5 describes the LED states when the board is powered up and the 10/100/1000 Gigabit

Ethernet LAN subsystem is operating.

Table 5. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs

LED LED Color LED State Indicates

Left Off LAN link is not established

Green

On LAN link is established

Blinking LAN activity is occurring

N/A Off 10 Mb/s data rate

Green On 100 Mb/s data rate

Right

Yellow On 1000 Mb/s data rate

Hi-Speed USB 2.0 Support

NOTE

Computer systems that have an unshielded cable attached to a USB port might not meet FCC

Class B requirements, even if no device or a low-speed USB device is attached to the cable.

Use a shielded cable that meets the requirements for a full-speed USB device.

The desktop board supports up to eight USB 2.0 ports via ICH7; four ports routed to the back

panel and four routed to two internal USB 2.0 headers. USB 2.0 ports are backward compatible

with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer

rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation. This

may be required to accommodate operating systems that do not support USB 2.0.

Enhanced IDE Interface

The ICH7’s IDE interface handles the exchange of information between the processor and

peripheral devices like hard disks, CD-ROM drives, and Iomega Zip

*

drives inside the computer.

The interface supports:

• Up to two IDE devices (such as hard drives)

• ATAPI-style devices (such as CD-ROM drives)

• Older PIO Mode devices

• Ultra DMA-33 and ATA-66/100 protocols

• Laser Servo (LS-120) drives

Serial ATA

The desktop board supports four Serial ATA channels (3.0 Gb/s) via ICH7, connecting one device

per channel.

Intel Desktop Board D945PSN Product Guide

18

Expandability

The desktop board supports the following:

• One PCI Express x16 add-in card

• Two PCI Express x1 add-in card

• Four PCI add-in cards

Related Links:

For information about installing the PCI Express x16 card, see page

36 in Chapter 2.

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI/PCI

Express and IDE auto-configuration utilities, and the video BIOS. The BIOS is stored in the Serial

Peripheral Interface (SPI) Flash or Firmware Hub.

The BIOS can be entered by pressing the <F2> key at startup. The BIOS can be updated by

following the instructions on page

53 in Chapter 3.

Serial ATA and IDE Auto Configuration

If you install a Serial ATA or IDE device (such as a hard drive) in your computer, the auto-

configuration utility in the BIOS automatically detects and configures the device for your computer.

You do not need to run the BIOS Setup program after installing a Serial ATA or IDE device. You

can override the auto-configuration options by specifying manual configuration in the BIOS Setup

program.

PCI and PCI Express Auto Configuration

If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express auto-

configuration utility in the BIOS automatically detects and configures the resources (IRQs, DMA

channels, and I/O space) for that add-in card. You do not need to run the BIOS Setup program after

you install a PCI/PCI Express add-in card.

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can be accessed

and who can boot the computer. A supervisor password and a user password can be set for the

BIOS Setup and for booting the computer, with the following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup options. If

only the supervisor password is set, pressing <Enter> at the password prompt of Setup gives the

user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the supervisor password

or the user password to access Setup. Setup options are then available for viewing and

changing depending on whether the supervisor or user password was entered.

• Setting a user password restricts who can boot the computer. The password prompt is

displayed before the computer is booted. If only the supervisor password is set, the computer

boots without asking for a password. If both passwords are set, you can enter either password

to boot the computer.

Desktop Board Features

19

Related Links:

For instructions on resetting the password, see

Clearing Passwords on page 47.

Chassis Intrusion

The board supports a chassis security feature that detects if the chassis cover has been removed.

The security feature uses a mechanical switch on the chassis that can be connected to the chassis

intrusion header on the desktop board. See

Figure 20 on page 39 for the location of the chassis

intrusion header.

Power Management Features

Power management is implemented at several levels, including:

• Advanced Configuration and Power Interface (ACPI)

• Hardware support:

⎯ Power connectors

⎯ Fan connectors

⎯ Suspend to RAM (Instantly Available PC technology)

⎯ Wake from USB

⎯ Wake from PS/2 keyboard/mouse

⎯ PME# wakeup support

ACPI

ACPI gives the operating system direct control over the power management and Plug and Play

functions of a computer. The use of ACPI with the desktop board requires an operating system that

provides full ACPI support.

Power Connectors

The desktop board has three power connectors. See Figure 23 on page 44 for the location of the

power connectors.

Fan Connectors

The desktop board has a 4-pin processor fan header and two 3-pin chassis fan headers. See

Figure 22 on page 43 for the location of the fan headers.

Fan Speed Control (Intel

®

Precision Cooling Technology)

Intel Precision Cooling Technology automatically adjusts the processor fan speed based on the

processor thermal diode temperature and adjusts the chassis fan speeds depending on the system

temperature. System fan noise may be reduced by operating controlled chassis and processor fans

at the minimum necessary speeds.

The processor and chassis fan speed control features can be disabled independently through the

desktop board BIOS. Disabling the processor fan speed control will result in the fan operating at

full speed if it is not a self controlled fan. It is recommended that processor fan speed control

remain enabled (default BIOS setting) when using the processor fan heat-sink included with Intel

®

boxed processors. Disabling the chassis fan speed control results in chassis fans always operating

Intel Desktop Board D945PSN Product Guide

20

at full speed. The chassis fan speed control feature should be disabled if a self-controlled chassis

fan is attached to any controlled chassis fan header.

The overall system noise reduction will vary based on system configuration and environment.

Suspend to RAM (Instantly Available PC Technology)

CAUTIONS

For Instantly Available PC technology, the 5 V standby line for the power supply must be capable

of delivering adequate +5 V standby current. Failure to provide adequate standby current when

using this feature can damage the power supply and/or affect ACPI S3 sleep state functionality.

Power supplies used with this desktop board must be able to provide enough standby current to

support the standard Instantly Available (ACPI S3 sleep state) configuration. If the standby

current necessary to support multiple wake events from the PCI and/or USB buses exceeds power

supply capacity, the desktop board may lose register settings stored in memory.

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-RAM) sleep

state. While in the S3 sleep state, the computer will appear to be off. When signaled by a wake-up

device or event, the system quickly returns to its last known awake state.

The desktop board’s standby power indicator, shown in

Figure 3, is lit when there is standby power

to the system. This includes the memory modules and PCI bus connectors, even when the

computer appears to be off.

If the system has a dual-colored power LED on the front panel, the sleep state is indicated by the

LED turning amber.

OM17748

Figure 3. Location of Standby Power Indicator

Related Links:

For more information on standby current requirements for the desktop board, refer to the Technical

Product Specification by going to the following link, finding the product, and selecting Product

Documentation from the left-hand menu:

http://support.intel.com/support/motherboards/desktop/

La pagina sta caricando ...

Intel D945PSN Manuale utente

Questo manuale è adatto anche per

Intel D945PSN Manuale utente

in altre lingue

Documenti correlati

Altri documenti