Tyan TOMCAT K8S Manuale utente

1

http://www.TYAN.com

Tomcat K8S

///

S2850

Revision 1.01

reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Tomcat K8S S2850 are trademarks of TYAN Computer Corporation.

AMD, AMD Opteron, and combinations thereof, are trademarks of Advanced Micro Devices, Inc.

HyperTransport is a licensed trademark of the HyperTransport Technology Consortium.

AMI, AMIBIOS are trademarks of AMI Software Incorporated.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE,is a trademark of SuSE AG.

Linux is a trademark of Linus Torvalds.

QLogic, Zircon, and combinations thereof are trademarks of QLogic Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Broadcom is a trademark of Broadcom Corporation and/or its subsidiaries

ATI and Rage XL are trademarks of ATI Corporation

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN products including

liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,

loss of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

2

http://www.TYAN.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.00 Congratulations!

1.01 Hardware Specifications

Chapter 2: Board Installation

2.00 Block Diagram

2.01 Board Parts, Jumpers and Connectors

2.02 Jumper Settings

2.03 IPMI I

2

C Bus Connector (J13)

2.04 Clear CMOS Jumper (J14)

2.05 USB Header (J22)

2.06 Serial Port Internal Header (J31)

2.07 FAN Connectors (J32~J37)

2.08 Keyboard Lock Jumper (J41)

2.09 External Speaker Header (J42)

2.10 Front Panel Connector (J43)

2.11 Chassis Intrusion Header (J48)

2.12 Gigabit LAN1 LED Header (J51)

2.13 Gigabit or 10/100M LAN2 LED Header (J52)

2.14 Power LED Connector

2.15 Tips on Installing the Motherboard in Chassis

2.16 Installing the Memory

2.17 Installing the Processor and Heatsink

2.18 Thermal Interface Material

2.19 Heatsink Installation Procedures

2.20 Attaching Drive Cables

2.21 Installing Add-In Cards

2.22 PCI Riser Cards Supported on Tomcat K8S S2850

2.23 Connecting External Devices

2.24 Installing the Power Supply

2.25 Finishing up

Chapter 3: BIOS

3.00 BIOS Setup Utility

3.01 BIOS Menu Bar

3.02 BIOS Legend Bar

3.03 BIOS Main Menu

3.04 BIOS Advanced Menu

3.04.1 IDE Configuration Sub-Menu

3.04.2 Floppy Configuration Sub-Menu

3.04.3 Super I/O Configuration Sub-Menu

3.04.4 Hardware Health Configuration Sub-Menu

3.04.5 Event Log Control Sub-Menu

3.04.6 Remote Access Configuration Sub-Menu

3.04.7 USB Configuration Sub-Menu

3.04.8 Onboard Device Sub-Menu

3.04.9 Watchdog Timer Sub-Menu

3.05 BIOS PCI/PnP Menu

3.06 BIOS Boot Menu

3.06.1 Boot Settings Configuration Sub-Menu

3.07 BIOS Security Menu

3.08 BIOS Chipset Setting Menu

3.08.1 North Bridge Chipset Configuration Sub-Menu

3.08.2 South Bridge Chipset Configuration Sub-Menu

3.09 BIOS – Power Menu

………….………………..Page 4

…………………………..Page 5

………….………………..Page 5

……………….…………..Page 5

…………………………..Page 7

……………….…………..Page 8

…………….……………..Page 9

……………..…………..Page 10

………….…………….. Page 10

………………………… Page 11

………………………… Page 12

……….………..…….… Page 13

…………….…..…….… Page 13

………………………… Page 14

………………………… Page 15

………………………… Page 16

………………………… Page 17

………………………… Page 20

………………………… Page 22

………………………… Page 24

……………..…………..Page 25

……………..…………..Page 27

……………..…………..Page 28

……………..…………..Page 29

……………..…………..Page 30

……………..…………..Page 31

…………………………Page 32

……………….…………Page 33

…………….……………Page 33

…………….……………Page 34

……...……….…………Page 36

…………………………Page 37

…………………………Page 38

…………………………Page 39

…………………………Page 40

…………………………Page 41

……………..…………..Page 42

…………………………Page 43

…………………………Page 44

…………………………Page 45

…………….……………Page 48

3

http://www.TYAN.com

3.09.1 Advanced ACPI Configuration Sub-Menu

3.09.2 Global Timer Reload Sub-Menu

3.10 BIOS Exit Menu

Chapter 4: Diagnostics

4.00 Beep Codes

4.01 Flash Utility

Appendix I: Glossary

Technical Support

…………….……………Page 50

…………….……………Page 51

…………….……………Page 52

…………………………Page 53

…………………………Page 54

…………………………Page 58

4

http://www.TYAN.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1 x Tomcat K8S S2850 motherboard

1 x CPU retention frame

1 x CPU back plate with insulation and screws

1 x 34-Pin floppy drive cable

1 x Ultra-DMA-133/100/66/33 IDE cable

4 x SATA cable (optional)

2 x SATA Driver Power Adapter (optional)

1 x 25-pin printer cable (optional)

1 x Tomcat K8S S2850 User’s Manual

1 x Tomcat K8S S2850 Quick Reference

1 x TYAN driver CD

1 x Serial ATA driver diskette (optional)

1x I/O shield

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

5

http://www.TYAN.com

Chapter 1: Introduction

1.00 – Congratulations!

You have purchased one of the most powerful AMD Opteron

TM

processor solutions, the Tomcat

K8S S2850. The Tomcat K8S S2850 features a high bandwidth integrated memory controller for

superior productivity, HyperTransport™ chipset technology to increase overall performance by

removing or reducing I/O bottlenecks, and low profile I/O ports with strategically placed DIMM slots

to allow maximum airflow across the motherboard for efficient system cooling. This platform offers

convenient remote Intelligent Platform Management Interface (IPMI) monitoring through a Server

Management Daughter Card. The Tomcat K8S S2850 also features an ATX form factor, Single or

Dual Gigabit Ethernet port, an onboard ATI 8MB PCI RAGE XL VGA, and an onboard Quad

channel Serial ATA, which provides an advanced and versatile solution for your server needs.

Remember to visit TYAN’s Website at http://www.tyan.com

. There you can find information on all of

TYAN’s products with FAQs, distributors list and BIOS setting explanations.

1.01 – Hardware Specifications

Processor

- PGA 940-pin ZIF socket

- Supports one AMD Opteron

TM

processor

- Onboard 3-phase PWM Controller

- Integrated 128-bit DDR Memory Controller

Chipset

- AMD-8111

TM

HyperTransport

TM

I/O Hub

- Winbond W83627HF Super I/O chip

- Winbond W83782D Hardware Monitor

chip

Memory

- 128-bit dual channel memory bus

- Total of four 184-pin 2.5-Volt DDR DIMM

sockets

- Supports up to 8 Gigabytes Registered

DDR *

- Supports ECC type memory modules

- Supports PC1600, PC2100, & PC2700

DDR *

Expansion Slots

- Total of six 32-bit 33MHz (5-Volt) PCI

slots

Integrated Enhanced IDE Controller

- Provides two IDE dual-drive ports for up to

four EIDE devices

- Supports UDMA 33/66/100/133 IDE drives

and ATAPI compliant devices

Integrated I/O

- One floppy connector supports up to

two drives

- Two 9-pin serial ports (one connector

and one header) and One 25-pin

parallel port header (connector is

optional)

- PS/2 mouse and keyboard

connectors

- Four USB v1.1 ports (2 stacked rear

connectors; 2 USB headers)

BIOS

- AMI

®

BIOS 8.0 on 4Mbit LPC Flash

ROM

- Supports ACPI 1.0b

- 48-bit LBA Support

- Supports PXE via Ethernet

- Supports USB device boot

- Watchdog timer

System Management

- Total of six 3-pin fan headers

- All fan headers with tachometer

monitoring

- One 2-pin Chassis Intrusion header

- Temperature, voltage and fan

monitoring

6

http://www.TYAN.com

Integrated LAN Controllers

- Dual Broadcom

®

BCM5705 GbE/100/10

LAN controllers

- Two RJ-45 LAN connectors with LEDs

Integrated PCI Graphics

- ATI



Rage

TM

XL PCI graphics controller

- 8MB Frame Buffer of video memory

Integrated Serial ATA Controller (MFG

Option)

- Silicon Image SiI3114 SATA controller

- Supports four-channel SATA RAID (RAID

0,1, 0+1)

- Total of four 7-pin SATA connectors

- Supports SATA 1.0 Specification

* Not validated at the time of print, subject to

change.

Form Factor

- ATX footprint (12” x 8.2”)

- 6-layer board

- ATX12V universal power connectors

- Serial (one) and VGA (one)

connectors

- Stacked USB 1.1 (two) connectors

- Stacked PS/2 keyboard and mouse

connectors

- Two RJ-45 LAN connectors with

LEDs

Regulatory

- FCC Class B (Declaration of

Conformity)

- European Community CE

(Declaration of Conformity)

Software Specifications

OS (Operating System) Support

Microsoft Windows NT 4 Service Pack 6A

Microsoft Windows 2000

Microsoft Windows XP

Microsoft Windows Server 2003

SuSE Server 8.0 for AMD-64

Red Hat 8.0, 9.0

Other distributions of Linux pending validation

TYAN reserves the right to add support or discontinue support for any OS with or

without notice.

7

http://www.TYAN.com

Chapter 2: Board Installation

Installation

You are now ready to install your motherboard. The mounting-hole pattern of the Tomcat K8S

S2850 matches the ATX specification. Before continuing with installation, confirm that your chassis

supports an ATX motherboard.

How to install our products right…. the first time!

The first thing you should do is read this user’s manual. It contains important information that will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch a safely grounded

object to release static charge (i.e. power supply case). For the safest conditions, Tyan

recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex the

board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory modules,

and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag that the

board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis, as well as

installing the processor, memory, disk drives and cables.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

8

http://www.TYAN.com

2.00 – Block Diagram

AMD-8111

TM

HyperTransport

TM

IO HUB

AMD Opteron

TM

Processor

200-333MHz

144bit Reg DDR

8x8 H

yp

erTrans

p

ort

TM

@

400MT/s

PCI

32-bit, 33MHz

LPC

Super I/O

SATA SiI3114

BCM5705

/BCM4401

ATI Rage XL

EIDE (ATA 133)

USB 1.1

FDD

Port

PS/2

KB&MS

Printer

&

Serial ports

LPC

Winbond 83782D

Optional

BMC

(IPMI 1.5)

SMB

IPM

ICM

BIOS

Optional

9

http://www.TYAN.com

2.01 – Board Parts, Jumpers and Connectors

Note: A □ depicts pin #1

This diagram is representative of the latest board revision available at the time of publishing.

The board you receive may not look exactly like the above diagram.

10

http://www.TYAN.com

2.02 – Jumper Settings

Jumper Function Settings

J13 IPMI I2C Bus Connector See Section 2.03

J14 Clear CMOS Jumper See Section 2.04

J22 USB Header See Section 2.05

J31 Serial Port Internal Header See Section 2.06

J32 Chassis Fan Connector See Section 2.07

J33 CPU Fan Connector See Section 2.07

J34 Chassis Fan Connector See Section 2.07

J35 Chassis Fan Connector See Section 2.07

J36 Chassis Fan Connector See Section 2.07

J37 Chassis Fan Connector See Section 2.07

J41 Keyboard Lock Connector See Section 2.08

J42 External Speaker Header See Section 2.09

J43 Front Panel Connector See Section 2.10

J48 Chassis Intrusion Header See Section 2.11

J51 LAN 1 LED Header See Section 2.12

J52 LAN 2 LED Header See Section 2.13

J57 Power LED Connector See Section 2.14

Jumper Legend

OPEN - Jumper OFF Without jumper cover

CLOSED - Jumper ON With jumper cover

To indicate the location of pin-1

2.03 – IPMI I

2

C Bus Connector (J13)

Pin_4 : NC

Pin_3 : SMBUSC_0

Pin_2 : GND

Pin_1 : SMBUSD_0

Use this connector to connect external IPMI

I

2

C Bus devices

11

http://www.TYAN.com

2.04 – Clear CMOS Jumper (J14)

Pin_3

Pin_1

Default

Pin_3

Pin_1

Clear

You can reset the CMOS settings by using this

jumper if you have forgotten your system/setup

password or need to clear system BIOS setting.

- Power off system and disconnect both

power connectors from the

motherboard

- Use jumper cap to close Pin_2 and Pin_3

for several seconds to Clear CMOS

- Put jumper cap back to Pin_1 and Pin_2

(default setting)

Reconnect power & power on system

2.05 – USB Header (J22)

Signal Description

#

Signal Description

VCC 1 2 VCC

USB Channel_1 Data - 3 4 USB Channel_2 Data -

USB Channel_1 Data

+

5 6

USB Channel_2 Data

+

GND 7 8 GND

NC 9 10 GND

12

http://www.TYAN.com

2.06 – Serial Port Internal Header (J31)

Signal Description Pin # Pin #

Signal

Description

DCD (Data Carrier

Detect)

1 2

DSR (Data-Set-

Ready)

RXD (Receive-

Data)

3 4

RTS (Request-to-

Send)

TXD (Transfer-

Data)

5 6

CTS (Clear-to-

Send)

DTR (Data-

Terminal-Ready)

7 8

RI (Ring-

Indicator)

GND

9 10

NC

2.07 – FAN Connectors (J32~J37)

#

FAN

Description

Function

Amp Rated

(Maximum)

J33 CPU FAN1

RPM

Read

1.0A

J34

Chassis

FAN2

RPM

Read

1.0A

J35

Chassis

FAN3

RPM

Read

1.0A

J32

Chassis

FAN4

RPM

Read

1.0A

J36

Chassis

FAN5

RPM

Read

1.0A

J37

Chassis

FAN6

RPM

Read

1.0A

13

http://www.TYAN.com

2.08 – Keyboard Lock Jumper (J41)

OPEN (Default)

To enable PS/2 keyboard

CLOSED

To disable PS/2 keyboard

2.09 – External Speaker Header (J42)

Pin_1 : Speaker +

Pin_2 : Buzzer +

Pin_3 : Speaker/

Buzzer -

Pin_1

Pin_4

Pin_4 : Speaker -

Close Pin-2and Pin-3 (Default)

Enable onboard buzzer

Open Pin-1 ~ Pin-4

Disable onboard buzzer and can

connect to chassis 1x4 speaker

14

http://www.TYAN.com

2.10 – Front Panel Connector (J43)

Functi

on

#

Function

HDD

LED+

1 2

PWR

LED+

HDD

LED-

3 4 PWR LED-

Reset

Button -

5 6

PWR

Button+

Reset

Button+

7 8

PWP

Button -

NC 9 10

Sleep

Button+

NC 11 12

Sleep

Button-

NC 13 14 NC

NC 15 16 NC

Chassis

Intru +

17 18

Chassis

Intru -

2. 11 – Chassis Intrusion Header (J48)

1 2

Pin_1 INTRUDER_L

Pin_2 GND

The Chassis Intrusion Header

provides chassis intrusion-monitoring

function.

Note: For use with chassis that

support this feature.

15

http://www.TYAN.com

2. 12 – Gigabit LAN1 LED Header (J51)

Pin_4 : Green -

Pin_3 : Green +

Pin_2 : Yellow -

Pin_1

Pin_1 : Yellow +

Green LED solid= 10Mb link

Green LED flashing= 10Mb activity

Yellow LED solid= 100Mb link

Yellow LED flashing= 100Mb activity

Both LED Solid= Gigabit link

Both LED flashing= Gigabit activity

2. 13 – Gigabit or 10/100M LAN2 LED Header (J52)

Pin_4 : Green -

Pin_3 : Green +

Pin_2 : Yellow -

Pin_1

Pin_1 : Yellow +

Gigabit LAN:

The same as J51 (LAN1).

10/100M LAN (optional):

Green LED solid= 10Mb link

Green LED flashing= 10Mb activity

Yellow LED solid= 100Mb link

Yellow LED flashing= 100Mb activity

16

http://www.TYAN.com

2.14 – Power LED Connector

PIN_1 PWR LED (+)

PIN_2 NC

Pin_1

Pin_3

PIN_3 PWR LED (-)

Note: For some chassis with 3-pin

cable.

2.15 – Tips on Installing the Motherboard in Chassis

Before installing your motherboard, make sure your chassis has the necessary motherboard

support studs installed. These studs are usually metal and are gold in color. Usually, the chassis

manufacturer will pre-install the support studs. If you’re unsure of stud placement, simply lay the

motherboard inside the chassis and align the screw holes of the motherboard to the studs inside

the case. If there are any studs missing, you will know right away since the motherboard will not be

able to be securely installed.

Some chassis include plastic studs instead of metal. Although the plastic studs are usable, Tyan

recommends using metal studs with screws that will fasten the motherboard more securely

in place.

Below is a chart detailing what the most common motherboard studs look like and how they should

be installed.

17

http://www.TYAN.com

TIP: Use metal studs if possible, as they hold the motherboard into place more securely than

plastic standoffs.

2.16 – Installing the Memory

Before attempting to install any memory, make sure that the memory you have is compatible with

the motherboard as well as the processor. For example, while PC1600 DDR modules are

compatible with all DDR based motherboards, they will not work if you are required to run the

motherboard and processor buses at 133MHz. For this, PC2100 DDR modules are required.

Critically important is whether you’re using the recommended memory for the current board you

have. For this information, please check Tyan’s web site at: www.tyan.com

The following diagram shows the common types of RAM modules you may encounter depending

on your board:

18

http://www.TYAN.com

Here are a few key points to note before installing memory into your Tomcat K8S:

• AMD Opteron

TM

processors support 64bit (non-interleaved) or 128bit (interleaved)

memory configurations

• At least ONE Registered DDR SDRAM module must be installed for the system to

turn on and POST (power on self test)

• 128MB, 256MB, 512MB, 1GB, and 2GB* Registered PC2700/PC2100/PC1600 DDR

SDRAM memory modules are supported

• All installed memory will be automatically detected

• The Tomcat K8S supports up to 8GB. *

* Not validated at the time of print, subject to change.

Valid DIMM Configurations

The processor supports 64-bit mode and 128-bit mode configurations of the DIMMs. In 64-bit

mode, only DIMMs 1 and 3 can be populated. Possible combinations of DIMMs in 64-bit mode are

listed in the table as below. In 128-bit mode, a minimum of two DIMMs is required to create the

128-bit bus; therefore, DIMMs can only be populated in even numbered pairs in slots 1 & 2, and 3

& 4. The following table shows some possible combinations of DIMMs for 128-bit mode. Not all

possible combinations are listed in the table.

19

http://www.TYAN.com

This chart outlines the rules for populating memory

(Note: X = Do not populate)

DIMM Slot DIMM1 DIMM2 DIMM3 DIMM4

X X 256 X

256 X 256 X

X X 512 X

512 X 512 X

X X 1024 X

1024 X 1024 X

X X 2048 X

1024 X 2048 X

2048 X 2048 X

X X 4096 X

64-bit

Mode

(MB)

4096 X 4096 X

X X 256 256

256 256 256 256

X X 512 512

512 512 512 512

X X 1024 1024

1024 1024 1024 1024

X X 2048 2048

2048 2048 2048 2048

X X 4096 4096

128-bit

Mode

(MB)

4096 4096 4096 4096

Memory Installation Procedure

When installing memory modules, make sure the modules align properly with the memory socket.

There should be keys (small indents) on your memory modules that fit according to the keys in the

memory socket. DDR modules and sockets have only one key, which is slightly near the center of

the module/socket. SDRAM modules (also referred to as PC100 or PC133) and their sockets have

two keys and will not insert into DDR DIMM sockets. The method of installing memory modules is

detailed in the following diagrams.

Once the memory modules are firmly seated in the socket, two clamps on either side will close and

secure the module into the socket. Sometimes you may need to close the clamps manually.

20

http://www.TYAN.com

To remove the memory module, simply push the clamps outwards until the memory module pops

up. Then simply remove the module.

TIP: When installing memory, a module may require a considerable amount of force to seat

properly, although this is very rare. To avoid bending and damaging your motherboard, place it on

its anti-static bag and onto a flat surface, and then proceed with memory installation.

NOTE

YOU MUST ALWAYS unplug the power connector to the

motherboard before performing system hardware changes, to

avoid damaging the board or expansion device.

2.17 – Installing the Processor and Heatsink

Your Tomcat K8S S2850 supports the latest 64-bit processor technologies from AMD. However,

only AMD Opteron

TM

processor are certified and supported with this motherboard. Check the

following page on TYAN’s website for latest processor support:

http://www.Tyan.com

The following diagrams will detail how to install your processor:

The processors you choose to use may not look exactly like the one pictured above, nor will the

socket look exactly the same. The diagram is provided as a visual guide to help you install socket

processors.

1. Lift the lever on the socket until it is approximately 130

o

or as far back as possible to the

socket.

2. Align the processor with the socket. There are keys underneath the processor just like on

memory modules to ensure that they insert the correct way.

3. Seat the processor firmly into the socket by gently pressing down until the processor sits

flush with the socket.

4. Place the socket lever back down until it snaps into place.

5. Your processor is installed.

La pagina si sta caricando...

Tyan TOMCAT K8S Manuale utente

Questo manuale è adatto anche per

Tyan TOMCAT K8S Manuale utente

in altre lingue

Documenti correlati

Altri documenti