D.T.S. Illuminazione s.r.l.
Via Fagnano Selve 10/12/14
47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it http://www.dts-lighting.it
Made in Italy
2
Le informazioni contenute in questo documento sono state attentamente redatte e
controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.
Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,
riprodotto per intero o in parte senza previo consenso scritto della D.T.S .
D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche
estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna
responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and
checked. However, no responsibility will be taken for any errors. All rights are
reserved and this document cannot be copied, photocopied or reproduced, in part or
completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to
any of its products without prior notice. D.T.S. assumes no responsibility for the use or
application of the products or circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées
avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas
d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié,
photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement
préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,
fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline
toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits
décrits.
Las informaciones contenidas en este documento han sido cuidadosamente
redactadas y controladas. Con todo, no se asume ninguna responsabilidad por
eventuales inexactitudes. Todos los derechos han sido reservados y este documento
no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa
autorización escrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de
carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume
responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los
productos o de los circuitos descritos.
3
INDEX:
1- SYMBOLS 4
2- GENERAL WARNING 5
3- GENERAL WARRANTY CONDITION 5
4- TECHNICAL FEATURES 6
5- ACCESSORIES 8
6- IMPORTANT SAFETY INFORMATION 9
6.1 Fire prevention
6.2 Prevention of electric shock
6.3 Protection against ultraviolet radiation
6.4 Safety
6.5 Level of protection against the penetration of solid and liquid objects
7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT 10
8- VOLTAGE AND FREQUENCY 15
9- INSTALLATION 15
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION 18
10.1 Protection
11- DMX SIGNAL CONNECTION 19
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING 20
13- DISPLAY FUNCTIONS 21
14- ERROR MESSAGES 25
15- HIDDEN MENU 26
15.1 Calibration mode
15.2 Power Setup menu
16- PAN SPEED & TILT SPEED 29
17- OPENING THE PROJECTOR HOUSING 29
18- PERIODIC CLEANING 30
18.1 Lenses and reflectors
18.2 Fans and air passages
19- PERIODIC CONTROLS 30
20- DMX PROTOCOL 31
21- FIXED GOBO WHEEL 38
22- COLOUR WHEEL 39
4
1- SYMBOLS
Graphic symbols used on this manual:
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC
SHOCK RISK
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE
UNIT ON INFLAMMABLE SURFACES”
THIS SYMBOL MEANS “RADIATION FROM
THIS LAMP CAN CAUSE DAMAGE TO EYES
AND SKIN”
MINIMUM DISTANCE FROM THE OBJECTS
AND THE PEOPLE LIT BY THE LIGHT BEAM
!
F
UV
15M
5
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important
information regarding safety during installation, use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or
experienced person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or
overheating.
The device must always be equipped with an efficient ground connection.
MINIMUM DISTANCE FROM THE OBJECTS AND THE PEOPLE
The projector needs to be positioned so that the objects and the people hit by the
beam of light are at least 15 meters (49,21 ft) from the unit frontal lens.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 36 months from the date of purchase against manufacturing
material defects.
6
4- TECHNICAL FEATURES
Overview
RAPTOR is the most compact Beam moving head on the market: just 37 cm x 50 cm.
RAPTOR projects the most powerful beam of light (150.000 Lux at 15 m) and the most
concentrated one.
RAPTOR can perfectly focus its 17 gobos at any distance.
Its unique selectable ‘Smooth’ filter eliminates the hot spot typical of Beam projectors,
evenly diffusing luminosity at any point of the light beam.
RAPTOR comes equipped with the ‘FPR’ (patented) system, which allows limitless
pan rotation, in either direction, never having to reverse motion.
Also, the unit features the fastest strobe effect.
RAPTOR
(D.T.S. Product Code: 03.MB005.EB.L)
• Electronic ballast 90-260V 50/60 Hz • Black finish
RAPTOR FPR
(D.T.S. Product Code: 03.MB005.EB.LFP)
• Electronic ballast 90-260V 50/60 Hz • FPR (Free Pan Rotation) • Black finish
Lamp
Osram Sirius HRI 330W (16.500 Lumens)
Colour temperature: 7.500°K
Optical group
Beam opening: 0,6° - 3,4°
16-bit motorized linear focus
Linear dimmer / shutter / ultra-fast strobe
150.000 Lux at 15 m
Colour generation
17-colour wheel with linear selection for perfect 2-colour beams
Dynamic effects
17-gobo wheel
8-facet rotating prism
Filters
Smooth filter (eliminates the hot spot, evenly diffusing luminosity)
Frost filter
7
4- TECHNICAL FEATURES
Interface / Control / Programming
LCD graphic display (control / management / monitoring of the main parameters)
4 soft-keys
Controlled via DMX 512
RDM
Wireless ready
ARTNET available on request
Internal operating system updatable via D.T.S. RED BOX interface and
hyperterminal program on windows based PC
DMX
18 DMX channels
Pan & Tilt
RAPTOR FPR (03.MB005.EB.LFP)
'FPR': limitless pan rotation, in either directions, never having to reverse motion
Tilt 270° (1,2 sec.)
RAPTOR (03.MB005.EB.L)
Pan 540° (2,3 sec.); Tilt 270° (1,2 sec.)
New Tri-phase stepper motor technology for ultra-fast and silent Pan &Tilt movements
16-bit movement resolution
Power supply
Electronic ballast: 90-260V 50/60 Hz
Power consumption: 450W with PFC
Energy saving
Power saving mode (the lamp dims to 80% after shutter closure)
Connectors
DMX: 4x XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik;
Power supply: POWERCON connectors (Power In / Power Out) by Neutrik
Operating ambient temperature
-10° / 40°
Weight
15,4 Kg
Internal safety devices
Overvoltage circuit protection and overtemperature circuit protection
International certifications
Safety: EN 60598-1: 2009
EN 60598-2-17: 1989
EMC: EN 55015.2006
8
4- TECHNICAL FEATURES
Dimensions
Packaging Dimensions (LxWxH) Unit Dimensions (LxWxH)
420 x 440 x 580 mm 368x288x538mm
Weight: 18,9 Kg Weight: 15,4 Kg
5- ACCESSORIES
As standard
* 1 x Osram Sirius HRI 330W (already installed in the projector) (Code 0505S037)
* 1 x POWERCON male cable connector (Code 0520P014)
* 1 x XLR 5 Pins male cable connector (Code 0508B066)
* 1 x XLR 5 Pins female cable connector (Code 0508B065)
* 2 x Omega clamp with “Fast Lock” connection 1/4 turn
* User’s manual
Optional (on request)
• “C” Clamp G100 black / professional (max. load 200Kg) (Code 0521A015)
• Aliscaf Clamp (max. capacity load 100Kg) (Code 0521A008)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (Code
0521A010)
9
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention:
RAPTOR uses a Osram Sirius HRI 330W lamp.
The use of any other alternative lamp is not recommended and will null and void the
fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 m .
-Minimum distance from the closest illuminable surface: 15 m.
-Replace any blown or damaged fuses only with those of identical value (5AT).
Refer to the wiring diagram if there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
6.2 Prevention of electric shock:
-High voltage is present inside the unit.
Unplug the unit prior to performing any function which involves touching the inside of
the moving head, including lamp replacement.
-The level of technology inherent in the RAPTOR requires the assistance of
specialised personnel for all servicing.
Please refer to an authorised D.T.S. service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
6.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or plastic covering are damaged.
Their respective shielding functions will only operate efficiently if they are in perfect
working order.
-Never look directly the lamp when it is on.
6.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are
capable of supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the
failure of the main fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle
the unit until at least 20 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C.
-A hot lamp may explode, so always wait for at least 20 minutes prior to attempting to
replace the lamp.
-Always wear suitable hand protection when handling the lamp.
6.5 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the
penetration of solid and liquid objects is IP20.
For outdoor use, D.T.S. reccomend the use of the dedicated raincovers.
F
UV
!
!
15M
10
7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT
WARNING
Turn off the lamp before opening the unit head covers.
Never look directly at the lamp when it’s lit.
Discharge lamps emits UV rays; radiation from this lamp
can cause damage to eyes and skin.
Let the projector cool for at least 20 minutes.
Switch off the unit and unplug the Mains AC cable connector
before replacing the lamp.
REPLACEMENT LAMP (D.T.S. Code 0505S037) :
OSRAM SIRIUS HRI
Power 330W
Luminous flux 16.500 lm
Colour temperature 7.500°K
Rated life 1500 hours
The use of any other alternative lamp is not recommended and will null and void the
fixture's warranty.
!
UV
11
1) Loosen the 3 “¼ turn” screws which fix the head covers on both sides (picture 1) .
2) Once loosened the screws, simply lift the covers to access the internal components
(picture 2).
PICTURE 1 PICTURE 2
3) Unplug the indicated fan connectors from the fans resend card (picture 3);
Unplug the two indicated fast-on cable connectors (1 and 2) and using a flathead
screwdriver remove the indicated lamp cable (3) from the screw connector (picture 4).
PICTURE 3 PICTURE 4
12
4) Using a phillips screwdriver, loose the 4 screws A, B, C, D and remove the lamp fan
assembly (picture 5).
PICTURE 5
5) Loose the four screws E, F, G, H from the plate which fix the lamp (picture 6), then
loose the two screws on both sides of the lamp rear metal cover (picture 7) and
remove the old lamp.
PICTURE 6 PICTURE 7
13
6) Remove the cable connectors from the old lamp and apply them on the new lamp
(picture 8).
PICTURE 8
7) Put in place the new lamp in the lamp support.
Place the lamp connectors on the fan air conveyor side (picture 9).
PICTURE 9
8) Lamp sub-assembly can now be re-installed, following backward all the above
listed steps.
14
Lamp Alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating
of the dichroic filters and other components inside the unit.
The lamp alignment is also essential to obtain the maximum luminous performance by
the projection.
1) Mount the fixture in an orientation so that it may be squarely projected onto a
smooth white surface no less than 20 meters away.
2) Using a console or the “LAMP ADJUST” menu system, focus and open (white)
beam onto the surface and observe the beam.
3) Using a phillips screwdriver, rotate the 3 indicated adjusters until you achieve a hot
spot in the center.
When the lamp alignment is correctly optimized, you will have a hot spot in the center.
15
8- VOLTAGE AND FREQUENCY
The RAPTOR with electronic ballast can operate at 90-260V 50 or 60 Hz.
9- INSTALLATION
RAPTOR may be either floor or ceiling mounted.
For floor mounting installations, the RAPTOR is supplied with four rubber mounting
feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix
the unit to the mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the
weight of the unit, as should any clamps used to hang it.
The structure should also be sufficiently rigid so as not to move or shake whilst the
RAPTOR is moving.
Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the
RAPTOR by using the two omega clamps (provided in the box) in conjunction with
fixing clamps for truss (fixing clamps are not included into the unit box).
16
9.1- Safety cable
We recommend the use of a safety cable or chain connected to the RAPTOR and to
the suspension truss in order to avoid the fixture accidentally falling should the main
fixing point fail.
Make sure that the iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain/cord to the attachment point (A) located on the base
of the fixture, as shown in the picture below.
9.2 Protection against liquids
The projector contains electric and electronic components which should under no
circumstances come into contact with oil, water or any other liquid.
The proper unit functioning would be compromised should this occur.
!
17
15M
9.3- Movement
RAPTOR FPR (03.MB005.EB.LFP) Unlimited Pan rotation; Tilt 270° (1,2 sec.) .
RAPTOR (03.MB005.EB.L) Pan 540° (2,3 sec.); Tilt 270° (1,2 sec.) .
Do not place any obstructions in the path of the projector's movement.
WARNING
Do not place any object in the
path of the projector’s
movement
Free Pan Rotation (‘FPR’) No ‘FPR’
(03.MB005.EB.LFP) (03.MB005.EB.L)
Please Note: If two different RAPTOR model (with and without FPR) are controlled at
the same time via DMX controller, be shure that channel 6 (PAN FAR) is set to value
0. In this way, the RAPTOR with FPR will react to DMX same as RAPTOR with no
FPR function.
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place.
The minimum recommended distance from flammable material is 1 m.
Minimum distance from the object being illuminated is 15 m.
9.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans
located on both the base and head of the fixture.
These should, under no circumstances, be blocked or obstructed whilst the projector
is in operation. Doing so could cause the fixture to seriously overheat thereby
compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow.
The ambient temperature should NOT exceed 40°C.
F
!
18
10- MAINS CONNECTION
RAPTOR with electronic ballast operate at 90-260V 50-60 Hz.
Prior to connecting the unit to your mains supply, ensure that the model in your
possession correctly matches the mains supply available.
For connection purposes, ensure that your plug is capable of supporting 1,5 amps
at 230 VOLT, or 3 amps at 90 VOLT.
Strict adherence to regulatory norms is strongly recommended.
MAINS AC OUTPUT 90-260V 50/60 Hz (16A Max)
MAX 6 RAPTOR UNITS @ 230V
MAX 3 RAPTOR UNITS @ 120V
(03.MB005.EB.LFP)
(03.MB005.EB.L)
MAINS AC INPUT 90-260V 50/60 Hz
FUSE 5A T 5X20
10.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each RAPTOR.
A good earth connection is essential for the correct operation of the projector.
!
19
11- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal.
Connection between the mixer and the projector or between projectors must be carried
out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.
Ensure that the conductors do not touch each other.
Do not connect the cable ground to the XLR chassy.
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector
plug and connect it to the next projector by connecting the DMX OUT plug on the first
projector to the DMX IN plug of the second one.
This way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors
has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest
to use a DMX terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of
the DMX line.
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
20
11.1-DMX Addresses
RAPTOR can be controlled with 18 DMX channels.
In order to use the unit in 18 channels, set the following addresses on the mixer:
Projector 1 A001
Projector 2 A019 If you want to select the next projector, just add “18”
Projector 3 A037
….. A….
projector 6 A091
11.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers
on the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop
flashing and the projector is now setted to the new DMX address.
TRICKS:
If you keep pushed the UP or DOWN keys, the channels are calculated more quickly
and you get a faster selection.
12- FIRMWARE UPDATING
Warning:
This procedure require a base knowledge of computer applications and Windows
Hyperterminal program. Please refer to an authorised D.T.S. service centre.
To update the software version of the RAPTOR you need:
D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).
USB-DMX Driver for the D.T.S. RED BOX interface.
(The driver and the installation procedure are available in our web site
www.dts-lighting.it)
Updating the software version.
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the
unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Download the new software version into the unit by using Windows Hyperterminal
program.
It will be possible to download the software from the reserved area of D.T.S. web site:
www.dts-lighting.it.
!
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
