ONKYO TX-NR414 Manuale utente

Categoria
Ricevitori AV
Tipo
Manuale utente
E
n
AV RECEIVER
TX-NR414
Instruction Manual
Contents
Safety Information and Introduction ............2
Table of Contents...........................................6
Connections .................................................12
Turning On & Basic Operations..................19
Advanced Operations ..................................39
Controlling Other Components...................53
Appendix.......................................................59
Internet Radio Guide
Remote Control Codes
En-2
Safety Information and Introduction
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or
electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and follow
local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is
adequate ventilation.
Leave 20 cm (8") of free space at the top and sides and
10 cm (4") at the rear. The rear edge of the shelf or
board above the apparatus shall be set 10 cm (4") away
from the rear panel or wall, creating a flue-like gap for
warm air to escape.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
AVIS
PORTABLE CART WARNIN
G
S3125A
Safety Information and Introduction
En-3
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact your
Onkyo dealer.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do not
intend to use the unit for an extended period, remove
the power cord from the AC outlet.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an
extended period, remove the power cord from the AC
outlet.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
8. Handling Notes
If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
Do not leave rubber or plastic items on this unit for a
long time, because they may leave marks on the
case.
This unit’s top and rear panels may get warm after
prolonged use. This is normal.
If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be sure
to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Safety Information and Introduction
En-4
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CONFORME À LA NORME NMB-003
DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse needs
to be replaced, the replacement fuse must approved by
ASTA or BSI to BS1362 and have the same ampere rating
as that indicated on the plug. Check for the ASTA mark or
the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
K. MIYAGI
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
Safety Information and Introduction
En-5
Supplied Accessories
Make sure you have the following accessories:
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
Installing the batteries
Note
If the remote controller doesn’t work reliably, try replacing the
batteries.
Don’t mix new and old batteries or different types of batteries.
If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
Remove expired batteries as soon as possible to prevent damage
from leakage or corrosion.
Aiming the remote controller
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
Indoor FM antenna ( page 18)
AM loop antenna ( page 18)
Power cord (Taiwanese models) ( page 18)
Speaker cable labels ( page 12)
Remote controller (RC-834M) and two batteries (AA/R6)
(Note for China: The battery for the remote controller is not
supplied for this unit.)
Quick Start Guide
Batteries (AA/R6)
Remote control sensor
AV receiver
Approx. 16 ft. (5 m)
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will
enable you to obtain optimum performance and
listening enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Safety Information and Introduction
En-6
Table of Contents
Safety Information and Introduction
Important Safety Instructions ......................................2
Precautions ...................................................................3
Supplied Accessories...................................................5
Table of Contents..........................................................6
Features.........................................................................7
Front & Rear Panels......................................................8
Front Panel..................................................................8
Display ........................................................................9
Rear Panel ................................................................10
Remote Controller.......................................................11
Controlling the AV Receiver ......................................11
Connections
Connecting the AV Receiver......................................12
Connecting Your Speakers .......................................12
About AV Connections..............................................14
Connecting Components with HDMI .........................15
Connecting Your Components ..................................16
Connecting Onkyo Components .........................17
Connecting the Antennas..........................................18
Connecting the Power Cord ......................................18
Turning On & Basic Operations
Turning On/Off the AV Receiver ................................19
Turning On ................................................................19
Turning Off ................................................................19
Playback ......................................................................20
Playing the Connected Component ..........................20
Controlling Contents of USB or Network Devices .....21
Understanding Icons on the Display .........................22
Playing an iPod/iPhone via USB ...............................22
Playing a USB Device ...............................................23
Listening to vTuner Internet Radio ............................23
Registering Other Internet Radio ..............................24
Playing Music Files on a Server................................25
Remote Playback ......................................................26
Listening to AM/FM Radio.........................................27
Using Basic Functions...............................................30
Using the Listening Modes .......................................30
Using the Home Menu ..............................................35
Using the Sleep Timer .............................................. 36
Setting the Display Brightness.................................. 36
Displaying Source Information.................................. 36
Changing the Input Display....................................... 37
Using the Music Optimizer........................................ 37
Muting the AV Receiver ............................................37
Using Headphones ...................................................38
Advanced Operations
On-screen Setup......................................................... 39
Using the Quick Setup ..............................................39
Using the Audio Settings of Quick Setup..................40
Using the Setup Menu (HOME) ................................41
About the HYBRID STANDBY indicator ...................42
Setup menu items..................................................... 42
HDMI Input................................................................ 43
Component (Component Video Input) ......................43
Digital Audio (Digital Audio Input) .............................44
Sp Config (Speaker Configuration)........................... 44
Sp Distance (Speaker Distance)............................... 45
Level Cal (Level Calibration)..................................... 45
Audio Adjust.............................................................. 46
Source Setup ............................................................47
Hardware .................................................................. 48
HDMI Setup ..............................................................49
Network Setup .......................................................... 50
Zone 2 ..........................................................................52
Making Zone 2 Connections .....................................52
Controlling Zone 2 Components ...............................52
Controlling Other Components
iPod/iPhone Playback via Onkyo Dock ....................53
Using the Onkyo Dock ..............................................53
Controlling Your iPod/iPhone.................................... 54
Controlling Other Components.................................55
Preprogrammed Remote Control Codes ..................55
Entering Remote Control Codes............................... 55
Remapping Colored Buttons..................................... 55
Remote Control Codes for
Onkyo Components Connected via ................. 56
Resetting the REMOTE MODE Buttons ...................56
Resetting the Remote Controller ..............................56
Controlling Other Components .................................57
Appendix
Troubleshooting ......................................................... 59
Firmware Update ........................................................ 64
Connection Tips and Video Signal Path .................. 68
Using an RIHD-compatible TV, Player,
or Recorder .............................................................. 69
About HDMI................................................................. 71
Network/USB Features............................................... 72
License and Trademark Information ........................ 75
Specifications............................................................. 76
To reset the AV receiver to its factory defaults, turn it
on and, while holding down CBL/SAT, press
ON/STANDBY ( page 59).
Safety Information and Introduction
En-7
Features
Amplifier
• 80 Watts/Channel @ 8 ohms (FTC)
• 130 Watts/Channel @ 6 ohms (IEC)
• 160 Watts/Channel @ 6 ohms (JEITA)
Optimum Gain Volume Circuitry
• H.C.P.S. (High Current Power Supply) Massive High
Power Transformer
Processing
• HDMI (Audio Return Channel, 3D, DeepColor,
x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD
High Resolution Audio, Dolby TrueHD, Dolby Digital
Plus, DSD and Multi-CH PCM)
Non-Scaling Configuration
A-Form Listening Mode Memory
•Direct Mode
• Pure Audio Mode (European, Australian and Asian
models)
• Music Optimizer for Compressed Digital Music files
• 192 kHz/24-bit D/A Converters
Powerful and Highly Accurate 32-bit Processing DSP
• Jitter Cleaning Circuit Technology
Connections
• 6 HDMI Inputs and 1 Output
Onkyo for System Control
• 4 Digital Inputs (2 Optical/2 Coaxial)
Component Video Switching (2 Inputs/1 Output)
Banana Plug-Compatible Speaker Posts
*
In Europe, using banana plugs to connect speakers to an audio
amplifier is prohibited.
• Internet Radio Connectivity (SiriusXM Internet
Radio/vTuner/Last.fm/Pandora/Rhapsody/Slacker/
Mediafly/AUPEO!)
*
Available services may vary depending on the region.
Network Capability for Streaming Audio Files
Front-Panel USB Input for Memory Devices and
iPod
®
/iPhone
®
models
Miscellaneous
• 40 FM/AM Presets
Crossover Adjustment
(40/50/60/70/80/90/100/120/150/200 Hz)
A/V Sync Control Function (up to 400 ms)
• Auto Standby Function
On-Screen Display via HDMI
Preprogrammed -Compatible Remote
Safety Information and Introduction
En-8
Front & Rear Panels
For detailed information, see the pages in parentheses.
ON/STANDBY button (19)
ZONE 2, OFF buttons (52)
Remote control sensor (5)
Display (9)
LISTENING MODE buttons (30)
DIMMER button (North American and Taiwanese
models) (36)
MEMORY button (28)
TUNING MODE button (27)
DISPLAY button (36)
SETUP button (41)
TUNING / , PRESET / (27), cursor and
ENTER buttons
RETURN button
MASTER VOLUME control (20)
MUSIC OPTIMIZER button and indicator (North
American and Taiwanese models) (37, 40)
PHONES jack (38)
TONE and Tone Level buttons (40)
Input selector buttons (20)
AUX INPUT AUDIO/VIDEO jacks (16)
USB port (16)
HYBRID STANDBY indicator (42)
PURE AUDIO button and indicator (European,
Australian and Asian models) (30)
RT/PTY/TP button (European, Australian and
Asian models) (28)
Front Panel
(North American and Taiwanese models) (European, Australian and Asian models)
Safety Information and Introduction
En-9
s
For detailed information, see the pages in parentheses.
Z2 (Zone 2) indicator (52)
3D indicator
This lights when a 3D input signal is detected.
Headphone indicator (38)
, and cursor indicators (22)
Listening mode and format indicators (30)
M.Opt indicator (37, 40)
Tuning indicators
RDS indicator (excluding North American and
Taiwanese models) (28)
AUTO indicator (27)
TUNED indicator (27)
FM STEREO indicator (27)
MUTING indicator (37)
Input indicators (68)
HDMI indicator (49)
DIGITAL indicator
ARC indicator (50)
USB indicator (22, 23)
NET indicator (23 to 26, 51)
Message area
SLEEP indicator (36)
Channel/Unit indicators
ch indicator
Hz indicator
m/ft indicator
dB indicator
ASb indicator (48)
Display
Safety Information and Introduction
En-10
DIGITAL IN COAXIAL and OPTICAL jacks
COMPONENT VIDEO IN and OUT jacks
ETHERNET port
FM ANTENNA jack and AM ANTENNA terminal
HDMI IN and OUT jacks
SPEAKERS terminals
(CENTER, FRONT, SURROUND)
Power cord (North American, European, Australian
and Asian models)
REMOTE CONTROL jack
Composite video and analog audio jacks
(BD/DVD IN, CBL/SAT IN, GAME IN, PC IN,
TV/CD IN)
ZONE 2 LINE OUT jacks
SUBWOOFER PRE OUT jack
MONITOR OUT V jack
AC INLET (Taiwanese models)
Rear Panel
(North American, European, Australian and Asian models) (Taiwanese models)
See “Connecting the AV Receiver” for connection
( pages 12 to 18).
Safety Information and Introduction
En-11
Remote Controller
For detailed information, see the pages in parentheses.
RECEIVER button (19)
REMOTE MODE/INPUT SELECTOR buttons (20)
/ / / and ENTER buttons
Q SETUP button (39)
Listening Mode buttons (30)
DIMMER button (36)
MUTING button (37)
DISPLAY button (36)
VOL / button (20)
RETURN button
HOME button (35)
SLEEP button (36)
Controlling the tuner
To control the AV receiver’s tuner, press AM or FM (or
RECEIVER).
/ buttons (27)
D.TUN button (27)
DISPLAY button
CH +/– button (28)
Number buttons (27)
*1
To control a component, you must first enter the remote
control code.
See “Entering Remote Control Codes” for more details
( page 55).
Controlling the AV Receiver
*1
To control the AV receiver, press RECEIVER to select
Receiver mode.
You can also use the remote controller to control
Onkyo Blu-ray Disc/DVD player, CD player, and
other components.
See “Entering Remote Control Codes” for more
details ( page 55).
En-12
Connections
Connecting the AV
Receiver
Connecting the Speaker Cables
The following illustration shows how to connect the
speakers to each pair of terminals.
Screw-type speaker terminals
Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends
of the speaker cables, and twist the bare wires tightly, as
shown.
Banana Plugs (North American models)
If you are using banana plugs, tighten the speaker
terminal before inserting the banana plug.
Do not insert the speaker code directly into the center
hole of the speaker terminal.
Speaker Configuration
The following table indicates the channels you should use
depending on the number of speakers that you have.
No matter how many speakers you use, a powered
subwoofer is recommended for a really powerful and solid
bass.
To get the best from your surround sound system, you need
to set the speaker settings manually ( page 44).
Attaching the Speaker Cable Labels
The speaker terminals are color-coded for identification
purpose.
The supplied speaker cable labels are also color-coded and
you should attach them to the positive (+) side of each
speaker cable in accordance with the table above. Then all
you need to do is to match the color of each label to the
corresponding speaker terminal.
Connecting Your Speakers
1/2" to 5/8" (12 to 15 mm)
Center
Surround
right
Front right
Surround
left
Front left
Number of speakers 2 3 4 5
Front speakers ✔✔✔✔
Center speaker ✔✔
Surround speakers ✔✔
Speaker Color
Front left White
Front right Red
Center Green
Surround left Blue
Surround right Gray
Connections
En-13
Speaker Connection Precautions
Read the following before connecting your speakers:
You can connect speakers with an impedance of between
6 and 16 ohms. If you use speakers with a lower
impedance, and use the amplifier at high volume levels
for a long period of time, the built-in amp protection
circuit may be activated.
Disconnect the power cord from the wall outlet before
making any connections.
Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the positive and negative wires.
Doing so may damage the AV receiver.
Make sure the metal core of the wire does not have
contact with the AV receiver’s rear panel. Doing so may
damage the AV receiver.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
Using a Powered Subwoofer
To find the best position for your subwoofer, while playing
a movie or some music with good bass, experiment by
placing your subwoofer at various positions within the
room, and choose the one that provides the most satisfying
results.
Tip
If your subwoofer is unpowered and you’re using an external
amplifier, connect the subwoofer pre out jack to an input on the
amplifier.
LINE INPUT
LINE INPUT
Powered
subwoofer
Corner
position
1/3 of wall
position
Connections
En-14
Connecting AV components
a
• Before making any AV connections, read the manuals
supplied with your AV components.
Don’t connect the power cord until you’ve completed and
double-checked all AV connections.
• Push plugs in all the way to make
good connections (loose connections
can cause noise or malfunctions).
To prevent interference, keep audio
and video cables away from power
cords and speaker cables.
AV Cables and Jacks
HDMI
HDMI connections can carry digital video and audio.
Component video
Component video separates the luminance (Y) and color
difference signals (PB, PR), providing the best picture
quality (some TV manufacturers label their component
video sockets slightly differently).
Composite video
Composite video is commonly used on TVs, DVDs, and
other video equipment.
Optical digital audio
Optical digital connections allow you to enjoy digital
sound such as PCM
*1
, Dolby Digital or DTS. The audio
quality is the same as coaxial.
Coaxial digital audio
Coaxial digital connections allow you to enjoy digital
sound such as PCM
*1
, Dolby Digital or DTS. The audio
quality is the same as optical.
Analog audio (RCA)
Analog audio connections (RCA) carry analog audio.
*1
Available sampling rate for PCM input signal (stereo/mono) is
32/44.1/48/88.2/96 kHz. In case of an HDMI connection,
176.4/192 kHz is also available.
Note
The AV receiver does not support SCART plugs.
The AV receiver’s optical digital jacks have shutter-type covers
that open when an optical plug is inserted and close when it’s
removed. Push plugs in all the way.
Caution
To prevent shutter damage, hold the optical plug straight
when inserting and removing.
About AV Connections
HDMI cable
Other cables
: Video & Audio
: Video
Game console
Blu-ray Disc/
DVD player
TV, projector, etc.
AV receiver
TV, projector, etc.
AV receiver
Game console
Blu-ray Disc/
DVD player
: Audio
Right!
Wrong!
Green
Blue
Red
Yellow
Orange
Y
P
B
PR
White
Red
Connections
En-15
*
If your TV doesn’t support Audio Return Channel (ARC), you
need to connect an optical digital cable together with the HDMI
cable to the AV receiver.
*
When listening to an HDMI component through the AV
receiver, set the HDMI component so that its video can be seen
on the TV screen (on the TV, select the input of the HDMI
component connected to the AV receiver). If the TV power is off
or the TV is set to another input source, this may result in no
sound from the AV receiver or the sound may be cut off.
Connect your components to the appropriate jacks. The
default input assignments are shown below.
: Assignment can be changed ( page 43).
See also:
“Connection Tips and Video Signal Path” ( page 68)
“Using an RIHD-compatible TV, Player, or Recorder”
( page 69)
“About HDMI” ( page 71)
Tip
To listen to the audio of a component connected via HDMI
through your TV’s speakers, enable “HDMI Through
( page 49) and set the AV receiver to standby mode.
Note
In the case of Blu-ray Disc/DVD players, if no sound is output
despite following the above-mentioned procedure, set your Blu-
ray Disc/DVD player’s HDMI audio settings to PCM.
Audio Return Channel (ARC) function
Audio Return Channel (ARC) function enables an HDMI
capable TV to send the audio stream to the HDMI OUT of
the AV receiver.
This function can be used when:
Your TV is ARC capable, and
–The TV/CD input selector is selected, and
–“HDMI Ctrl (RIHD)” is set to “On”( page 49), and
–“Audio Return Ch” is set to “Auto” ( page 50).
Connecting Components with HDMI
Game console
TV, projector, etc.
Satellite/cable set-top box, etc.
Blu-ray Disc/DVD player
Personal computer
Jack Components
HDMI IN1 Blu-ray Disc/DVD player
HDMI IN2 Satellite/cable set-top box, etc.
HDMI IN3 Game console
HDMI IN4 Personal computer
HDMI IN5 Other components
HDMI IN6 Other components
HDMI OUT TV, projector, etc.
Connections
En-16
Connect your components to the appropriate jacks. The
default input assignments are shown below. See
“Connection Tips and Video Signal Path” for more
information ( page 68).
: Assignment can be changed ( page 43).
Note
*1
When USB input is selected, you can input video signals from
the AUX INPUT VIDEO jack. Video signals input from AUX
INPUT VIDEO will be output from the MONITOR OUT jack.
*2
Do not connect the AV receiver’s USB port to a USB port on
your computer. Music on your computer cannot be played
through the AV receiver in this way.
*3
Connect a turntable (MM) that has a phono preamp built-in. If
your turntable (MM) doesn’t have it, you’ll need a
commercially available phono preamp.
If your turntable has a moving coil (MC) type cartridge, you’ll
need a commercially available MC head amp or MC
transformer as well as a phono preamp. See your turntable’s
manual for details.
• With connection , you can enjoy Dolby Digital and
DTS. (To listen in Zone 2 as well, use and .)
• With connection , you can listen audio from the
external components while you are in Zone 2.
• With connection , if your Blu-ray Disc/DVD player
has both the main stereo and multichannel outputs, be
sure to connect the main stereo.
Connecting Your Components
The on-screen menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to other video outputs, use the AV receiver’s display
when changing settings.
No. Jack/Port Components
AUX INPUT
VIDEO Camcorder, etc
AUDIO L/R
USB, AUX INPUT
VIDEO
*1
iPod/iPhone (video
playback)
USB
*2
iPod/iPhone, MP3 player,
USB flash drive
DIGITAL IN
OPTICAL 1 (GAME) Game consoles
OPTICAL 2 (TV/CD) TV, CD player
COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player
COAXIAL 2 (CBL/SAT) Satellite/cable set-top box,
RI dock, etc.
COMPONENT VIDEO
IN 1 (BD/DVD) Blu-ray Disc/DVD player,
RI dock
IN 2 (CBL/SAT) Satellite/cable set-top box,
RI dock, etc.
OUT TV, projector, etc.
ETHERNET Router
MONITOR OUT TV, projector, etc.
BD/DVD IN Blu-ray Disc/DVD player
CBL/SAT IN Satellite/cable set-top box,
etc.
GAME IN Game console, RI dock
PC IN Personal computer
TV/CD IN TV, CD player, cassette
tape deck, MD, CD-R,
Turntable
*3
, RI dock
Connections
En-17
With (Remote Interactive), you can use the following
special functions:
System On/Auto Power On
When you start playback on a component connected via
, while the AV receiver is on standby, the AV
receiver will automatically turn on and select that
component as the input source.
Direct Change
When playback is started on a component connected via
, the AV receiver automatically selects that
component as the input source.
Remote Control
You can use the AV receiver’s remote controller to
control your other -capable Onkyo components,
pointing the remote controller at the AV receiver’s
remote control sensor instead of the component. You
must enter the appropriate remote control code first
( page 56).
Note
•Use only cables for connections. cables are supplied
with Onkyo components.
Some components have two jacks. You can connect either
one to the AV receiver. The other jack is for connecting
additional -capable components.
Connect only Onkyo components to jacks. Connecting other
manufacturer’s components may cause a malfunction.
Some components may not support all functions. Refer to the
manuals supplied with your Onkyo components.
While Zone 2 is on, the System On/Auto Power On and Direct
Change functions do not work.
Connecting Onkyo Components
1
Make sure that each Onkyo component is connected
with an analog audio cable (connection
in the
hookup examples) ( page 16).
2
Make the connection (see the illustration).
3
If you’re using an RI Dock, or cassette tape deck,
change the Input Display ( page 37).
L R
ANALOG
AUDIO OUT
L R
ANALOG
AUDIO OUT
e.g., cassette tape deck
RI Dock
Connections
En-18
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use
the tuner.
Note
Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible
reception.
Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.
Tip
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.
If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM
antenna.
Connecting the Antennas
Thumbtacks, etc.
Insert the plug fully
into the jack.
Insert the plug fully
into the jack.
North American and
Taiwanese models
European, Australian
and Asian models
Push. Insert wire. Release.
Assembling the AM loop antenna
Indoor FM antenna (supplied)AM loop antenna (supplied)
Caution
Be careful not to injure yourself
when using thumbtacks.
Note
Before connecting the power cord, connect all of your
speakers and AV components.
Turning on the AV receiver may cause a momentary power surge
that might interfere with other electrical equipment on the same
circuit. If this is a problem, plug the AV receiver into a different
branch circuit.
Do not use a power cord other than the one supplied with the AV
receiver. The supplied power cord is designed exclusively for use
with the AV receiver and should not be used with any other
equipment.
Never disconnect the power cord from the AV receiver while the
other end is still plugged into a wall outlet. Doing so may cause
an electric shock. Always disconnect the power cord from the
wall outlet first, and then the AV receiver.
Connecting the Power Cord
1
(Taiwanese models)
Connect the supplied power cord to the AV
receiver’s AC INLET.
2
Plug the power cord into an AC wall outlet.
To AC wall outlet
En-19
Turning On & Basic Operations
Turning On/Off the AV
Receiver
Tip
•The HYBRID STANDBY indicator may light depending on the
status of settings ( page 42).
For details on power management settings, see “Auto Standby”
( page 48).
RECEIVER
RECEIVER
ON/STANDBY
Turning On
1
Press ON/STANDBY on the front panel.
or
Press RECEIVER followed by RECEIVER on the
remote controller.
The AV receiver comes on and its display lights.
If the “Update New F/W” window appears.
When a new version of the firmware is available, the
notification window “Update New F/W” pops up. This
notification only appears when the AV receiver is
connected to your home network ( page 72). To
perform the firmware update, follow the instructions on
screen.
Use the / and ENTER buttons on the AV receiver or
remote controller to select one of the options, and then
press ENTER.
` Update Now
Starts the firmware update.
Refer to step 4 of “Update procedure”
( page 65).
` Remind me Later
The update notification will pop up again the next
time you turn the AV receiver on.
` Never Remind me
Disables the automatic update notification.
Tip
The update notification window can be enabled or disabled in
Update Notice” ( page 51).
Turning Off
1
Press ON/STANDBY on the front panel.
or
Press RECEIVER followed by RECEIVER on the
remote controller.
The AV receiver will enter standby mode. To prevent
any loud surprises when you turn on the AV receiver,
always turn down the volume before you turn it off.
Turning On & Basic Operations
En-20
Playback
Operating with the remote controller
Operating on the AV receiver
The on-screen menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to other video outputs, use the AV receiver’s display
when changing settings.
This section describes the procedure for using the
remote controller, unless otherwise specified.
Playing the Connected Component
1
Press RECEIVER followed by an INPUT
SELECTOR button.
2
Start playback on the source component.
See also:
• “Playing an iPod/iPhone via USB” ( page 22)
• “Playing a USB Device” ( page 23)
• “Listening to vTuner Internet Radio” ( page 23)
• “Registering Other Internet Radio” ( page 24)
• “Playing Music Files on a Server” ( page 25)
• “Remote Playback” ( page 26)
• “Listening to AM/FM Radio” ( page 27)
• “iPod/iPhone Playback via Onkyo Dock”
( page 53)
• “Controlling Other Components” ( page 55)
3
To adjust the volume, use VOL / .
4
Select a listening mode and enjoy!
See also:
• “Using the Listening Modes” ( page 30)
RECEIVER
VOL /
INPUT SELECTOR
Listening mode buttons
1
Use the input selector buttons to select the input
source.
2
Start playback on the source component.
3
To adjust the volume, use the MASTER VOLUME
control.
4
Select a listening mode and enjoy!
MASTER VOLUMELISTENING MODE
Input selector buttons
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128

ONKYO TX-NR414 Manuale utente

Categoria
Ricevitori AV
Tipo
Manuale utente

in altre lingue