Philips 42FD9934 Manuale utente

Marca: Philips

Modello: 42FD9934

Tipo: Manuale utente

CORRECTLY INCORRECTLY

Note: the enclosed template can be used for general positioning only

(fig. 1).

Mounting to sheetrock wall

Note: Bracket can only be used with standard 16" spaced wood wall

studs.

Bracket must be positioned so that the bracket is fastened firmly to

studs at each end.

All required hardware is included.

Note: Because the Receiver Unit’s power cord is 6’, when determining the

Display Unit mounting location, the distance to the nearest AC power

outlet must be considered.

& Determine desired location to mount Display Unit.

Within this area, locate the two 16.54" spaced wall studs that must

be used as the Wall Bracket mounting location. (fig. 1 and 2)

é With the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes must be drilled. (fig. 2)

Note: Use only the holes in Bracket.

“ Remove the Wall Bracket, and using a 13/64" wood drill bit, drill the

four holes. (fig. 3)

‘ Reposition the Wall Bracket, and with four lag bolts (fig. 4), secure

into place.Tighten with 13mm or 1/2" socket wrench. (fig. 5)

Note: Do not use plastic wall anchors with these lag bolts.

Note: Lag bolts must be fastened and centered securely into the stud.

Mounting Wall Bracket

fig. 1

fig. 2

420mm /16,54"

60,5mm /

2.38"

fig. 3

fig. 4

fig. 5

English

Mounting to concrete wall

Determine desired location to mount Display Unit. Use the enclosed

template for alignment purposes. (fig. 1)

é With the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes must be drilled. (fig. 4)

“ Remove the Wall Bracket, and using a 5/8" masonry drill bit, drill the

four holes. (fig. 2)

‘ Insert a concrete anchor (with bolt) into each hole.

( Firmly tighten each bolt.Then, remove the bolts.

§ Reposition the Wall Bracket, and with the four bolts (and washers),

secure into place.

Mounting to concrete block wall

Determine desired location to mount the Display Unit.

Within this area, position the Wall Bracket so that the four end

mounting holes are located over the cavities of the concrete blocks

(refer to Figure 1)

é With the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes are to be drilled.

Note: Use only the four outside or end holes in the Bracket.

“ Remove the Wall Bracket and reconfirm that the marks made in the

previous step are located in the cavities of the concrete blocks. Re-

locate the marks as required to ensure that they are in the cavities

of the concrete blocks.

‘ With a 1/2” masonry drill bit, drill the four holes.

( Hinge the plastic legs of the toggle bolt into the channel of the metal

end of the toggle bolt so it can fit into the 1/2” hole drilled in the

wall (refer to Figure 2).

§ Insert the toggle bolt into the hole in the wall and push it in until it

is in the cavity of the block.

è With the plastic pull ring of the toggle bolt, pull the metal end of the

toggle bolt firmly against the back of the cavity of the concrete block

(refer to Figure 3).

WASHER

Cavities In Block

Fig. 1

Fig. 2

Fig. 3

! While holding the plastic pull ring, slide the plastic retaining sleeve

towards the wall until it fits into the hole in the wall. This will hold

the toggle bolt in the wall while the Wall Bracket is mounted (refer

to Figure 4).

Push down on the lower plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 5).

Push up on the upper plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 6).

Install the remaining 3 toggle bolts in the remaining holes the same

way that the first one was installed.

Position the Wall Bracket in place and install the four 1/4-20 bolts,

including washers, in each of the outside corner holes. Do not

tighten completely (refer to Figure 7).

Confirm that the Wall Plate is level, then tighten the bolts securely

(refer to Figure 8).

Mounting to metal stud wall

Determine desired location to mount the Display Unit.

Within this area, locate the two 16.54” spaced metal wall studs that

must be used as the Wall Bracket mounting location.

é Locate the center of both wall studs at the height that the Wall

Bracket is to be mounted.

“ With the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes are to be drilled.

Note: Use only the four outside or end holes in the Bracket

(refer to Figure 1).

‘ Remove the Wall Bracket and reconfirm that the marks made in the

previous step are located in the center of the metal wall studs. Re-

locate the marks as required to ensure that they are in the center of

the metal wall studs (refer to Figure 2).

Metal Wall

Studs

Fig. 1

Holes Centered In

Metal Wall Studs

Fig. 2

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

( With a 1/2” drill bit, drill the four holes. A smaller pilot hole may be

required if the 1/2” drill bit bends the metal stud instead of piercing

it.

§ Hinge the plastic legs of the toggle bolt into the channel of the metal

end of the toggle bolt so it can fit into the 1/2” hole drilled in the

wall (refer to Figure 3).

è Insert the toggle bolt into the hole in the wall and push it in past the

metal stud (refer to Figure 3).

! With the plastic pull ring of the toggle bolt, pull the metal end of the

toggle bolt firmly against the back of the metal stud (refer to Figure

4).

While holding the plastic pull ring, slide the plastic retaining sleeve

towards the wall until it fits into the hole in the wall. This will hold

the toggle bolt in the wall while the Wall Bracket is mounted (refer

to Figure 5).

Push down on the lower plastic leg of the toggle bolt and break it

off flush with the wall (refer to Figure 6).

Push up on the upper plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 7).

Install the remaining 3 toggle bolts in the remaining holes the same

way that the first one was installed.

Position the Wall Bracket in place and install the four 1/4-20 bolts,

including washers, in each of the outside corner holes. Do not

tighten completely (refer to Figure 8).

Confirm that the Wall Plate is level, then tighten the bolts securely

(refer to Figure 9).

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1

VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

cover 1016.1 2.4 02-07-2002 09:44 Pagina 2

Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a

PHILIPS product. So complete and return the Warranty Registration Card enclosed with your

purchase at once, and take advantage of these important benefits.

Return your Warranty Registration card today to ensure

you receive all the

benefits

you’re entitled to.

For Customer Use

Enter below the Serial No., which is

located on the rear of the cabinet. Retain

this information for future reference.

Model No. __________________________

Serial No. __________________________

Congratulations on your purchase, and

welcome to the “family!”

Dear PHILIPS product owner:

Thank you for your confidence in PHILIPS.You’ve selected one of

the best-built, best-backed products available today.And we’ll do

everything in our power to keep you happy with your

purchase for many years to come.

As a member of the PHILIPS “family,” you’re entitled to

protection by one of the most comprehensive warranties and

outstanding service networks in the industry.

What’s more, your purchase guarantees you’ll receive all the

information and special offers for which you qualify, plus easy

access to accessories from our convenient home shopping

network.

And most importantly you can count on our uncompromising

commitment to your total satisfaction.

All of this is our way of saying welcome-and thanks for investing

in a PHILIPS product.

Sincerely,

Lawrence J. Blanford

President and Chief Executive Officer

P.S. Remember, to get the most from your PHILIPS

product, you must return your Warranty

Registration Card within 10 days. So please mail

it to us right now!

Know these

safety symbols

This “bolt of lightning” indicates

uninsulated material within your unit

may cause an electrical shock. For the

safety of everyone in your household, please

do not remove product

covering.

The “exclamation point” calls attention

to features for which you should read

the enclosed literature closely to

prevent operating and maintenance

problems.

WARNING: TO PREVENT FIRE OR

SHOCK HAZARD, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE.

CAUTION: To prevent electric shock,

match wide blade of plug to wide slot, fully

insert.

ATTENTION: Pour éviter les choc

électriques, introduire la lame la plus large de

la fiche dans la borne correspondante de la

prise et pousser jusqu’au fond.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Hurry!

Warranty

Verification

Registering your product within

10 days confirms your right to

maximum protection under the

terms and conditions of your

PHILIPS warranty.

Owner

Confirmation

Your completed Warranty

Registration Card serves as

verification of ownership in the

event of product theft or loss.

Model

Registration

Returning your Warranty Registration

Card right away guarantees you’ll

receive all the information and special

offers which you qualify for as the

owner of your model.

Visit our World Wide Web Site at http://www.philips.com

1016.1 en 02-07-2002 09:46 Pagina 1

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and third

grounding prong.The wide blade or third prong are provided for

your safety.When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus.When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

15. This product may contain lead or mercury. Disposal of these

materials may be regulated due to environmental considerations.

For disposal or recycling information, please contact your local

authorities or the Electronic Industries Alliance: www.eiae.org.

16. Damage Requiring Service - The appliance should be

serviced by qualified service personnel when:

A. The power supply cord or the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the

appliance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally or

exhibits a marked change in performance; or

E. The appliance has been dropped, or the enclosure damaged.

17. Tilt/Stability - All televisions must comply with recommended

international global safety standards for tilt and stability

properties of its cabinets design.

• Do not compromise these design standards by applying

excessive pull force to the front, or top, of the cabinet which

could ultimately overturn the product.

• Also, do not endanger yourself, or children, by placing

electronic equipment/toys on the top of the cabinet. Such

items could unsuspectingly fall from the top of the set and

cause product damage and/or personal injury.

18. Wall Mounting - The appliance should be mounted to a wall

only as recommended by the manufacturer.

19. Power Lines - An outdoor antenna should be located away

from power lines.

20. Outdoor Antenna Grounding - If an outside antenna is

connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-

1984, provides information with respect to proper grounding of

the mats and supporting structure grounding of the lead-in wire

to an antenna-discharge unit, size of grounding connectors,

location of antenna-discharge unit, connection to grounding

electrodes and requirements for the grounding electrode. See

Figure below.

21. Objects and Liquid Entry - Care should be taken so that

objects do not fall and liquids are not spilled into the enclosure

through openings.

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Note to the CATV system installer :This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE (NEC)

ANTENNA LEAD IN WIRE

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

1016.1 en 02-07-2002 09:46 Pagina 2

Unpacking and wall mounting instructions

For the unpacking instructions follow the illustrated steps printed on the

packaging (outside and inside). For the wall mounting instructions follow the

illustrated steps ‘ to § printed on the separate template and in the

supplied booklet.

Make sure that the wall mount is being fixed securely enough so that it meets

safety standards.The weight of the monitor (excl. packaging) is about 76 lbs.

Note: Stands are optional accessories. Consult your dealer.

Connect your computer

Directly to the monitor

& Connect one end of a VGA cable to the video card of the computer and the

other end to the

VGA 1 connector at the rear side of the monitor. Fix the

connectors firmly with the screws on the plug.

é In case of a multimedia computer, connect the audio cable to the audio

outputs of your multimedia computer and to the audio inputs of your external

amplifier.

VGA 2:The video connector for VGA 2 can be programmed to become an input or an

output via the Setup menu, see p. 8. The function of being input or output is

determined by the used mode. If the monitor is used in TV mode, the VGA 2 connector

is VGA output. If the monitor is used in monitor mode,the connector is VGA input or

output.

To a TV receiver box

See the handbook of the TV receiver box.

& Connect one end of a VGA cable to the video card of the computer and the

other end to the

PC/MAC IN connector at the rear side of the TV receiver

box. Fix the connectors firmly with the screws on the plug.

é In case of a Multimedia computer, connect the audio cable to the audio

outputs of your Multimedia computer and to the

AUDIO IN R and L inputs of

the TV receiver box. For sound reproduction, connect your external amplifier

to the TV receiver box.

Note: Only use the VGA cable supplied with the monitor.

Daisy chaining

The Loop Through facility makes it possible to make a daisy chain with a

second monitor.

Connect one end of another VGA cable to the

VGA 2 connector at the rear

side of the monitor and the other end to the

VGA 1 connector of a second

monitor.

The RC out jack next to the

VGA 2 connector makes it possible to daisy chain remote

control signals to other equipment.This output cannot be used to daisy chain a

second monitor.

~ MAINS

RS232

VGA 1

VGA 2

RC OUT

English

1016.1 en 02-07-2002 09:46 Pagina 3

VGA 640x480 60, 72, 75, 85 Hz

Wide VGA 848x480 60 Hz

Wide VGA 852x480 60 Hz

MAC 640x480 66.67 Hz

MAC 832x624 74.55 Hz

MAC 1024x768 74.93 Hz

MAC 1152x870 75 Hz

SVGA 800x600 56, 60, 72, 75, 85 Hz

XGA 1024x768 60, 70, 75, 85 Hz

SXGA 1280x1024 60

72 Hz (not with DVI-D-source)

When a VGA computer is connected, the display selection is made

automatically.

A message is displayed when the monitor does not support the connected

VGA mode.

Switch your computer to a correct display mode.

R6 / AA

Use of the remote control

Computer Display modes

Operation

& Insert the mains plug supplied into the mains inlet at the back of the

monitor and in the wall socket. Please, only use the supplied rim-earthed

mains cord which has to be inserted in a grounded socket.

é Remote control: remove the cover of the battery compartment.

Insert the 2 batteries supplied (Type LR6/AA-1.5V).

The batteries supplied do not contain the heavy metals mercury and cadmium.

Nevertheless in many countries batteries may not be disposed of with your

household waste. Please check on how to dispose of batteries according to local

regulations.

“ Make sure that your TV receiver box and/or PC are switched on and that

your PC is in the correct display mode.

‘ Switch the monitor on : Press the power button B at the right side of

the monitor.

A green indicator lights up and the screen comes on.

When the monitor does not receive a supported VGA signal and is not

connected to a receiver box the screen switches to standby and the red

indicator lights up.

When you switch on your monitor for the first time, and the monitor is

not connected to a TV receiver box, the menu language automatically

appears on the screen.The explanation appears in different languages one at

a time.

Follow the instructions on screen to select the correct language or see

Setup menu, Language, p. 8.

1016.1 en 02-07-2002 09:46 Pagina 4

5Use of the remote control 5

Use of the remote control

POWER

BRIGHTNESS

CONTRAST

ZOOM OUTZOOM INZOOM ON/OFF

VGA AV1 AV2 AV3

MUTE

AV MUTE

CH/PR

VGA

press repeatedly to select your computer

connected to the

VGA 1 or 2 connector or

to the

DVI-D connector.

AV1, AV2, AV3

press to select the peripherals connected

to the connector indicated on the monitor.

V no function (except when in

combination with a TV receiver box and

a Home Cinema audio receiver)

¬ no function (except when in

combination with a TV receiver box and a

Home Cinema audio receiver)

CH/PR Program selection

To browse through the sources selected.

B to switch to standby or on again

MENU to switch the menu on/off

cursor buttons to select your choice and

to alter a selected adjustment.

OK to activate your choice

AV MUTE to mute the picture or restore

it (if the monitor is used in monitor

mode).

When activated a green indicator starts

blinking in front of the monitor.

q Picture format

See Picture 2 menu, p. 7.

Press the q button to switch between

the different picture formats.

BRIGHTNESS +/-

to adjust the brightness level of the

picture

CONTRAST +/-

to adjust the contrast level of the picture

ZOOM ON/OFF

to activate/de-activate the zoom function.

See p. 7.

ZOOM IN/OUT

to adjust the zoom factor and to change

the magnification of the picture when

zoom is activated. See p. 7.

Use of the remote control

On screen information

When the monitor is used in the monitor mode, information about the active

source (

AV1, AV2, AV3, VGA1, VGA2 or DVI-D) and the supported video,VGA or

HD-format of the selected source is displayed on the screen together with the

selected picture format and icons informing about AV mute.

1016.1 en 02-07-2002 09:46 Pagina 5

Use of the menus

Use of the menus and the menu system

& Press the MENU button on the remote control to summon the different

menu headers.

é Press the cursor left/right to move the cursor horizontally through the menu

headers.

“ Press the cursor down to access the menu.

In case of a slider, move the cursor left/right to adjust.

In case of a list with options, move the cursor right to enter and use the

cursor up/down to select an option.

Press the cursor left to leave the options list.

‘ Press the MENU button again to switch off the menu.

Note: Sometimes not all the menu items are visible on the screen.

Press the cursor down until all the items are displayed.

Only when the US English language has been selected (see Setup menu,

Language, p. 8), the menu items will be displayed with additional icons.

Operation

Press the MENU button on the remote control to summon the main menu.

Picture 1 menu

Brightness

This control allows you to adjust the brightness level of the picture.

Contrast

This control allows you to adjust the contrast level of the picture.

Color (only available when the source is

AV1, AV2 or AV3 YCbCr)

This control allows you to adjust the saturation level of the colors to suit

your personal preference.

Color temperature

This control allows you to select the color temperature of the picture.

Move the cursor up/down to make a selection.

Press the cursor left to return to the Picture 1 menu.

Tint (only with NTSC signals and when the source is

AV1 or AV2)

This control allows you to compensate for the color variations in NTSC

encoded transmissions.

Sharpness

This control allows you to adjust the edge definition of a picture.

Brightness

Contrast

(Color)

Color temp.

(Tint)

Sharpness

Pict. a Pict. a Setup º

Brightness

Contrast

Color

Color temp.

(Tint)

Sharpness

Pict. a

Brightness

Contrast

Color temp.

Sharpness

Pict. a

SD video-mode

VGA-mode + HD video mode

1016.1 en 02-07-2002 09:46 Pagina 6

7Use of the menus

Picture 2 menu

Zoom

Select

Zoom On to activate the zoom function.You may also activate the

zoom function with the

ZOOM ON/OFF button on the remote control.

If no zoom is active, press the cursor left/right, up/down to select which part

of the screen will be zoomed.

Zoom factor

Select

Zoom factor and press the cursor left/right to adjust the zoom factor

and to change the magnification of the picture.

If zoom is not active changing the magnification factor will have no effect on

the displayed picture.

Format (only available in 4:3 VGA mode and SD video mode)

Select

Format to summon a list of available display formats.

Press the cursor up/down to select another display format: 4:3,

Movie Expand 16:9 or Wide screen.

Note: Movie Expand 16:9 is not available in VGA mode.

Shift (only available in VGA mode on VGA 1 or VGA 2 and in one of the HD

modes. See Connect Peripheral equipment, p. 9.)

This control allows you, when necessary, to move the picture in a horizontal

or vertical way.

& Use the cursor left/right, up/down to adjust.

é Press the OK button when done.

Clock frequency (only available in VGA mode on VGA 1 or VGA 2. See Connect

Peripheral equipment, p. 9.)

This control allows you, when necessary, to adjust the values of the clock

frequency so that especially text can be displayed with an optimal overall

sharpness.

Use the cursor left/right to adjust.

Phase (only available in VGA mode on VGA 1 or VGA 2.

See Connect Peripheral equipment, p. 9.)

This control allows you, when necessary, to adjust the pixel phase of the

picture to avoid picture interference.

Use the cursor left/right to adjust.

Auto align (only available in VGA mode on VGA1 or VGA2 and in one of the HD

modes. See Connect Peripheral Equipment, p. 9.)

This control allows you to automatically adjust the shift, the clock frequency

and the phase in VGA mode and the shift in HD modes.

Press OK to execute.

4:3

Wide screen

4:3

Movie expand 16:9

Wide screen

SD video-mode

4:3 VGA-mode

Format

4:3

Movie expand 16:9

Wide screen

Zoom

Zoom factor

Pict. a

(Format)

4:3

Wide screen

Zoom

Zoom factor

(Shift)

‹

(Clock frequency)

(Phase)

ﬁ

(Auto align)

Pict. a

SD video-mode

VGA-mode + HD video mode

1016.1 en 02-07-2002 09:46 Pagina 7

Use of the menus

Setup menu

Language

& Use the cursor down to select Language.

é Press the cursor right to enter the list of selectable languages.

“ Use the cursor up/down to scroll through the list and to bring up other

languages which are not displayed on the screen at present.

Note: Only with the US English language, the menu items will be displayed with

additional icons.

Power savings

This control allows you to overrule the automatic power savings feature.

In case

Power savings is switched Off, the power always remains on until the

monitor is forced to standby.

& Use the cursor down to select Power savings.

é Press the cursor left/right to select On or Off.

AV3

This control allows you to set the AV3 input to HD-RGB,YCbCr or HD-

YPbPr.When having selected

Auto, the monitor makes the selection

automatically between YCbCr, HD-YPbPr or HD-RGB.

See also p. 9, Equipment with Component Video Output connectors.

& Use the cursor down to select AV3.

é Press the cursor right to enter the list with options.

“ Press the cursor up/down to select one of the options.

VGA 2

This control allows you to select whether to set the VGA 2 connector as

input, output or even HD-input.

& Use the cursor down to select VGA 2.

é Press the cursor right to enter the list with options: VGA IN, VGA OUT or

HD IN.

“ Press the cursor up/down to select one of the options.

Note: AV3 and VGA 2 will not be available in VGA loop through mode, i.e. when a TV

receiver box is connected to the monitor and a VGA source is selected.

Language

‡

US English

Power savings

)

English

AV3

(

Nederlands

VGA2

Deutsch

Français

Español

Setup º

1016.1 en 02-07-2002 09:46 Pagina 8

Connect Peripheral Equipment

You may connect 3 possible VGA sources (VGA 1, VGA 2 or DVI-D) and

3 possible video sources (

VIDEO 1 (AV1), VIDEO 2 (AV2) and VIDEO 3

(AV3)) to the monitor.

The following diagrams show you where you can connect your peripheral

equipment.

Note: in case the monitor is operating in combination with a receiver box (TV mode),

the VGA and video inputs on the monitor will be disabled and the VGA 2

connector becomes an output.

Equipment with Y/C-SVHS output connectors

Connect the video cable to the

Y/C S-VHS VIDEO 2 (AV2) connector.

Equipment with CVBS output connectors

Connect the video cable to the

CVBS VIDEO 1 (AV1) connector.

Equipment with Component Video Output connectors

Note: VIDEO 3 (AV3) can handle the following video signals:YCbCr, HD-PbPr and

HD-RGB.The discrimination between the various input formats and the appropriate

video processing is done automatically. It is however possible to overrule the

automatic detection. See Setup menu, p. 8.

& Connect the video cables of your equipment with YPbPr output with

composite sync on Y, or of your equipment with YCbCr output with

composite sync on Y to the YPbPr, resp.YCbCr input

VIDEO 3 (AV3) IN

sockets of the monitor.

é Connect the video cables of your equipment with RGB output with separate

Horizontal and Vertical sync to the RGB input sockets and to the H and V

sockets

VIDEO 3 (AV3) of the monitor.

Note: when High Definition signals are inputted to the monitor via the YPbPr/RGB

input, the monitor switches to the HD Video Mode.

The following HD and ED video modes are supported by the monitor on the YPbPr,

RGB and VGA 2 HD input:

1920x1080/60I 720x480/60P

1280x720/60P 720x576/50P

The following SD video modes are supported by the monitor on theYCbCr input:

720x480/60I

720x576/50I

MAINS INLET

RS232

VGA 1 VGA 2

DVI-d

RC OUT

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VIDEO 2

(AV2)

VIDEO 1

(AV1)

VIDEO 3

(AV3)

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

VIDEO 2

(AV2)

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

VIDEO 1

(AV1)

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

VIDEO 3

(AV3)

1016.1 en 02-07-2002 09:46 Pagina 9

High Definition equipment with VGA connector

& Connect the VGA output of your equipment to the VGA2 connector.

Digital DVI output of your PC (DVI-D)

& Connect the Digital DVI output of your PC to the DVI-D connector.

RC out connector

This connector allows you to daisy chain remote control signals to other

equipment (e.g.AV receiver, IR repeater) which have an electrical RC in.

Note: it is not possible to daisy chain a second monitor.

Serial I/O port RS232

The RS232 connector is only to be used with the monitor as stand alone.

This connector allows you to control the monitor via your PC (as a

replacement of the remote control).

Note:This connector can also be used for dealer service tools.

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

DVI-D

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

VGA 2

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

RS 232

~ MAINS

RS232

DVI-D

Y/C S-VHS

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

VGA 1 VGA 2

RC-OUT

VIDEO 3

(AV3)

VIDEO 2

(AV2)

VIDEO 1

(AV1)

RC-OUT

1016.1 en 02-07-2002 09:46 Pagina 10

Ambient temperature

Do not hang up the monitor above a

central heating or other heating sources.

Care of the screen

Clean the anti-reflex coated flat glass

screen with a slightly damp soft cloth. Do

not use abrasives solvents as it can

damage the glass surface of the screen.

Plasma Display characteristics

Caution:A video source (such as a video

game, DVD, or TV information channel)

which shows a constant non-moving

pattern on the TV screen, can cause

damage to the screen.When your Flat-TV

is continuously used with such a source,

the pattern of the non-moving portion of

the game (DVD, etc.) could leave an image

permanently on the screen.When not in

use, turn the video source

OFF.

Regularly alternate the use of such video

sources with normal TV viewing.

When switching over to another picture

after having displayed the same still picture

for a long time (many hours), it may

happen that some parts from the previous

picture will remain on screen due to a

kind of memory effect.This ghost picture

will disappear after some time.To avoid

this effect change the pictures regularly or

for PC use you can turn on a screen saver

in your computer.

Philips has built in an automatic shift of

the picture in video mode every 5 minutes

to avoid this effect and to prolong the life

of the screen.

Very incidentally and after a longer period

of unuse (approx. 1 year) the screen may

display some strange color deficiencies.

This is quite normal for plasma displays

and these effects will disappear after the

set has been turned on for some time.

A plasma display consists of more than 3.1

Million color pixels. It is within industry

standards that very few pixels (< 0.001%)

may be defective, even for a new set.

There is however no reason to doubt

about the quality of the set.

The plasma display technology operates

with rare gases which are being influenced

by air pressure.

Up to an altitude of 6562 ft above sea-

level, the display is functioning fine.

Operating the set at a higher altitude, the

picture becomes unstable and the picture

performance is deteriorating. Bringing the

set below 6562 ft it works fine again.

Transportation has no influence.

Control of peripheral equipment

The infrared radiation of the screen may

influence the reception sensitivity of other

peripherals. Solution: replace the batteries

of the remote control or change position

of other equipment. E.g. keep away a

wireless headphone from within a radius

of 4,92 ft.

No stable or not synchronized VGA

picture

Check if you have selected the correct

display mode in your PC. See p. 4,

Computer display modes.

No picture

Are the supplied cables connected

properly? (The power cable to the display,

the VGA cables,...)

Is your PC switched on?

Do you see a black screen and the

indicator in front of the monitor lights up

green, this means that the display mode is

not supported.

Switch your VGA source to a correct

mode.

Remote control

If your monitor no longer responds to the

remote control, the batteries may be

exhausted.

If your problem is not solved:

Switch your monitor off and then on

again.

Never attempt to repair a defective

monitor yourself.

Check with your dealer or call a TV

technician.

Transport

Keep the original packaging to transport the

monitor if needed.

End of life directives

Philips is paying a lot of attention to

produce environmentally-friendly in green

focal areas.Your new monitor contains

materials which can be recycled and

reused.

At the end of its life specialized companies

can dismantle the discarded monitor to

concentrate the reusable materials and to

minimize the amount of materials to be

disposed of.

Please ensure you dispose of your old

monitor according to local regulations.

How to dispose of batteries ?

The batteries supplied do not contain the

heavy metals mercury and cadmium.

Nevertheless in many countries batteries

may not be disposed of with your

household waste. Please ensure you dispose

of batteries according to local regulations.

Miscellaneous

. Ambient temperature: + 5~ + 40°C

. Maximum operating altitude: 2000 m /

6562 ft (min. pressure 800 hPa)

. Mains:AC 95-264V 50/60 Hz

. Power consumption: around 290W

. Standby consumption: < 2W

. Weight (excl. packaging)

Display: 76 lbs

. Dimensions (wxhxd):

Display: 42.3 x 25.9 x 3.5 inch (42”)

. Wall mounting bracket included

Tips

1016.1 en 02-07-2002 09:46 Pagina 11

COLOR TELEVISION

90 Days Free Labor

One Year Free Replacement of Parts (Two Years Free Replacement on Color Picture Tube)

This product can be repaired in-home.

LIMITED WARRANTY

WHO IS COVERED?

You must have proof of purchase to receive warranty service. A sales

receipt or other document showing that you purchased the product is

considered proof of purchase.

WHAT IS COVERED?

Warranty coverage begins the day you buy your product. For 90 days

thereafter, all parts will be repaired or replaced free, and labor is free.

From 90 days to one year from the day of purchase, all parts will be

repaired or replaced free, but you pay for all labor charges. From one

to two years from the day of purchase, you pay for the replacement or

repair of all parts except the picture tube, and for all labor charges.

After two years from the day of purchase, you pay for the replacement

or repair of all parts, and for all labor charges.

All parts, including repaired and replaced parts, are covered only for

the original warranty period. When the warranty on the product

expires, the warranty on all replaced and repaired parts also expires.

WHAT IS EXCLUDED?

Your warranty does not cover:

• labor charges for installation or setup of the product, adjustment of

customer controls on the product, and installation or repair of

antenna systems outside of the product.

• product repair and/or part replacement because of misuse,

accident, unauthorized repair or other cause not within the control

of Philips Consumer Electronics Company.

• reception problems caused by signal conditions or cable or antenna

systems outside the unit.

• a product that requires modification or adaptation to enable it to

operate in any country other than the country for which it was

designed, manufactured, approved and/or authorized, or repair of

products damaged by these modifications.

• incidental or consequential damages resulting from the product.

(Some states do not allow the exclusion of incidental or

consequential damages, so the above exclusion may not apply to

you. This includes, but is not limited to, prerecorded material,

whether copyrighted or not copyrighted.)

• a product used for commercial or institutional purposes.

WHERE IS SERVICE AVAILABLE?

Warranty service is available in all countries where the product is

officially distributed by Philips Consumer Electronics Company. In

countries where Philips Consumer Electronics Company does not

distribute the product, the local Philips service organization will

attempt to provide service (although there may be a delay if the

appropriate spare parts and technical manual(s) are not readily

available).

MAKE SURE YOU KEEP...

Please keep your sales receipt or other document showing proof of

purchase. Attach it to this owner’s manual and keep both nearby.

Also keep the original box and packing material in case you need to

return your product.

BEFORE REQUESTING SERVICE...

Please check your owner’s manual before requesting service.

Adjustments of the controls discussed there may save you a service

call.

TO GET WARRANTY SERVICE IN U.S.A.,

PUERTO RICO OR U.S. VIRGIN ISLANDS...

Contact a Philips factory service center (see enclosed list) or

authorized service center to arrange repair.

(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties,

including implied warranties of merchantability and fitness for a

particular purpose, are limited in duration to the duration of this

express warranty. But, because some states do not allow limitations

on how long an implied warranty may last, this limitation may not apply

to you.)

FOR WARRANTY COVERAGE IN CANADA...

Note: Product Warranty coverage may vary between countries where

product is distributed by Philips Consumer Electronics Company. In

order to receive full and specific warranty details for products sold and

serviced in Canada, please contact Philips at:

1-800-661-6162 (from Canada - French Speaking)

1-800-531-0039 (English and Spanish Speaking)

REMEMBER...

Please record the model and serial numbers found on the product

below. Also, please fill out and mail your warranty registration card

promptly. It will be easier for us to notify you if necessary.

MODEL # ________________________________________________

SERIAL # ________________________________________________

This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.

Philips Consumer Electronics Company, P.O. Box 520890, Miami, FL 33152, (402) 536-4171

1016.1 en 02-07-2002 09:46 Pagina 12

★

•

Tampa/W Florida

★

•

San Francisco/Metro Area

•

Philadelphia/S New Jersey

•

Atlanta/N Georgia

•

Houston

Knoxville/E Tennessee

Charlotte

Los Angeles★

★

Indicates In-Home Service Only

Milwaukee: call Chicago

Cincinnati and Columbus: call Cleveland

Nashville and Chattanooga: call Knoxville

Washington/Baltimore: call Philadelphia

Charlotte: call Atlanta

All Florida locations: call Tampa

Los Angeles: call San Francisco

Toll-free numbers provided on the next page

• Indicates In-Home/Carry-In Service

Toll-free numbers provided on the next page

★

Milwaukee

Nashville

★

Chattanooga

★

Cincinnati

Orlando

Ft. Myers/SW Florida

Miami/SE Florida

•

Dallas-Fort Worth

★

Washington/Baltimore

★

Cleveland/N Ohio

★

Columbus

•

Chicago

•

Detroit/Toledo

•

Note: If you reside in one of our Philips Factory Service Branch areas (see directory on back), you can contact the nearest Service

Branch to obtain efficient and expedient repair for your product. If your product is In-Warranty, you should have proof-of-purchase

to ensure No Charge Service. For Out-of-Warranty service, call the location nearest you.

Nota: Si vous résidez dans une des régions desservies par une succursale de service après vente du fabricant Philips (voir liste ci-

dessous), vous pourrez contacter la branche de service après vente la plus près de chez vous pour obtenir un service après vente

rapide et efficace. Si le produit est sous garantie, il suffira de présenter une preuve d`achat pour bénéficier d'un service sans frais.

Pour les produits non couverts par la garantie, contactez le center le plus près de chez vous.

Nota: Si Ud. reside en una de nuestras zonas para sucursales Philips de servicio al de fábrica (ver directorio más abajo), Ud. puede

comunicarse con la sucursal de servicio más cercana para obtener una reparación oportuna y eficaz de su producto. Si su producto

está todavía bajo garantía, Ud. debe presentar comprobante de compra para no ocasionar ningunos cargos por servicio. Para

servicio después del vencimiento de la garantía, llame al lugar más cercano de los abajo indicados.

FACTORY SERVICE LOCATIONS

In Canada

How you can obtain efficient and expedient carry-in, mail-in, or in-home service for your product

Please contact Philips at 1-800-661-6162 (French speaking)

1-800-531-0039 (English or Spanish speaking)

Au Canada

Comment obtenir le service après-vente pour les produits apportés ou envoyés par la poste à notre center de service ou le service

à domicile

Veuillez contacter philips á: 1-800-661-6162 (Francophone)

1-800-531-0039 (Anglais ou Espagnol)

En el Canadá

Cómo recibir servicio efficiente para su producto, en persona, por correo o a domicillo

Favor de comunicarse con Philips al: 1-800-661-6162 (Francés)

1-800-531-0039 (Inglés o Español)

126 1014.2 serv. center us 02-07-2002 09:44 Pagina 1

Qualiy service is as close as your telephone! Simply look over the list below for the number of a Factory Service Center near you.

Your product will receive efficient and expedient carry-in, mail-in, or in-home service, and you will receive peace of mind, knowing youru

product is being given the expert attetin of Philips’ Factory Service.

Comment obtenir notre service après vente rapide et efficace soit par courrier, à domicile, ou en se présentant à un centre de service

Philips. Plus de 600 centres de réception de produits à réparer à travers le pays: contacter le centre de service aux consommateurs le

plus proche pour savoir l’emplacement de ces dépôts dans un rayon de 50 à 75 miles (80 km à 120 km) du centre de service local.

Cómo obtener un servicio oportuno y eficiente por correo, en casa o en persona para su producto a través de un centro Philips de

servicio. Mas de 600 sitios por todo el país para la recepción de productos necesitados de reparaciones: comunicarse con el centro de

servicio de fabrica mas cercano para estos lugares dentro de un radio de 80 a 120 km (50 a 75 millas) del centro de servicio local.

ATLANTA

Philips Factory Service

550 Franklin Road., Suite F

Marietta, GA 30067

800-273-1501

TAMPA

Philips Factory Service

1911 US Highway 301 North

Tampa, FL 33619

800-442-2027

SAN FRANCISCO

Philips Factory Service

681 East Brokaw Rd.

San Jose, CA 95112

800-300-9103

HOUSTON

Philips Factory Service

1110 N. Post Oak Rd., Suite 100

Houston,TX 77055

800-952-3254

CLEVELAND

Philips Factory Service

950 Keynote Circle

Brooklyn Heights, OH 44131

800-331-7037

DETROIT

Philips Factory

25173 Dequindre

Madison Heights, MI 48071

800-438-1398

DALLAS-FORT WORTH

Philips Factory Service

415 N. Main Street, #107

Euless,TX 76040

800-952-3254

CHICAGO

Philips Factory Service

1279 W. Hamilton Pkwy.

Itasca, IL 60143

800-531-2922

KNOXVILLE

Philips Factory Service

6700 D Papermill Rd.

Knoxville,TN 37919

800-821-1767

PHILADELPHIA

Philips Factory Service

352 Dunks Ferry Rd.

Bensalem, PA 19020

800-847-9320

FACTORY SERVICE LOCATIONS

126 1014.2 serv. center us 02-07-2002 09:44 Pagina 2

Philips 42FD9934 Manuale utente

Marca: Philips

Modello: 42FD9934

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Philips 42FD9934 User manual

Philips 42FD9934 Manuale utente

Philips 42FD9934 Manuale utente

in altre lingue

Documenti correlati

Altri documenti