Ubiquiti MFI-MSC Guida Rapida

Marca: Ubiquiti

Modello: MFI-MSC

Categoria: Rilevatori di movimento

Tipo: Guida Rapida

Ceiling Mount

Motion Sensor

Model: mFi‑MSC

Introduction

Thank you for purchasing the Ubiquiti mFi

™

Ceiling Mount

Motion Sensor. This sensor is designed for use with the

mFi mPort. Once they are connected, you can use the mFi

Controller software to monitor your sensors using your

Web browser.

Package Contents

g u

mFi Ceiling Mount

Motion Sensor

Quick Start Guide Mounting Bracket

M3x50 Flat Head

Screws (Qty. 3)

M3 Keps Nuts

(Qty. 3)

M3x12 Washers

(Qty. 3)

3 x 20 mm Drywall Screws

(Qty. 3)

M6x30 Screw Anchors

(Qty. 3)

Jumpers

(Qty. 2)

mFi

™

Ceiling Mount Motion Sensor

Installation Requirements

• mFi mPort

• CAT5/6 Cable

• Phillips Screwdriver

• Optional: Drill and Drill Bit (1.6 mm for M3x50 Flat Head

Screws or 6 mm for 3x 20 mm Drywall Screws)

Hardware Overview

Front

Motion Sensor

Hardware Installation

Back

mFi RJ45 Port

Hardware Installation

Installation Tips

• Avoid installing the mFi‑MSC in areas where it will face

direct or reflected sunlight.

•

Avoid installing the mFi‑MSC in areas where the

environmental temperature may change rapidly.

•

LocatethemFi‑MSCatleastonemeterawayfromthe

nearest fluorescent light to avoid interference.

• Ensure there are no obstructions in the field of view.

• The CAT5/6 cable can come out the back or the side,

so it can be installed on any type of ceiling. If you are

mounting the mFi‑MSC on a ceiling tile, remove the tile

from the ceiling before installation.

mFi

™

Ceiling Mount Motion Sensor

Instructions

1. If you have a dropped ceiling, remove the ceiling tile.

2. Position the Mounting Bracket in the desired location.

Mark the three screw holes. If the CAT5/6 cable is wired

above the ceiling, mark a 25 mm hole as indicated

below.

25 mm Hole

3. Use a 1.6 mm drill bit to pre‑drill holes for the screws.

4. If the CAT5/6 cable is wired above the ceiling, cut or

drill the 25 mm circle you marked in step 2. This will be

used to feed the CAT5/6 cable through the ceiling.

Hardware Installation

5. Secure the Mounting Bracket to the ceiling using the

M3x50 Flat Head Screws, M3 Washers, and M3 Keps Nuts.

Note: If you have a drywall ceiling, use the

3x20mm Drywall Screws and M6x30 mm Screw

Anchors.

6. If you have a wiring hole in the ceiling, feed the CAT5/6

cable through the Mounting Bracket and wiring hole.

Seal the cable hole with a sealant, such as RTV (Room

Temperature Vulcanizing).

mFi

™

Ceiling Mount Motion Sensor

7. Connect the CAT5/6 cable to the mFi RJ45 Port of the

mFi‑MSC.

8. Align the notch on the mFi‑MSC with the notch on the

Mounting Bracket.

Hardware Installation

9. Turn the mFi‑MSC clockwise until it locks into place.

10. Connect the other end of the CAT5/6 cable from the

mFi‑MSCtoanmFiRJ45portonthemFimPort.

Refer to the User Guide on the CD‑ROM that was included

with your mFi mPort for instructions on configuring the

mFi‑MSC in the mFi Controller software. The User Guide is

also available at www.ubnt.com/mfi

mFi

™

Ceiling Mount Motion Sensor

Microwave Sensitivity Knob

The knob is located inside the product casing. Typically

there is no need to adjust the sensitivity of the microwave

sensor; however, you can turn the knob counter‑clockwise

(towards MIN) or clockwise (towards MAX) to make

adjustments.

MAX

MIN

If you need to access the microwave sensitivity knob or

jumper settings (see page 9), remove the back panel. Use a

Phillips screwdriver to remove the three screws.

Jumper Settings

The mFi‑MSC has jumpers located inside the product

casing. Typically there is no need to open the casing to

adjust the jumpers. The LED jumpers are the only ones

that you may want to change. You can turn on the LEDs

so the motion sensor illuminates when it is triggered

(seepage10).YoucanturnontheLEDspermanentlyor

temporarily for walk testing (testing the positioning of the

mFi‑MSC).

The following jumper settings are available:

Selection

ON OFF

MW (Microwave Sensor) Set to

enabled by default. Removing the

jumper will disable this sensor.

Enabled Disabled

PIR (Passive Infrared Sensor) Set

to enabled by default. Removing the

jumper will disable this sensor.

Enabled Disabled

LED The LEDs are off by default. ON OFF

mFi

™

Ceiling Mount Motion Sensor

LED

The LEDs are disabled by default and can only be enabled

by opening the product case and adjusting the jumper.

When the LEDs are enabled, the motion sensor will

illuminate in one of the following colors when motion is

detected.

Color Detection

Indicates that the microwave sensor detected

motion.

Indicates that the infrared sensor detected

motion.

Indicates that an alarm was triggered because

the infrared sensor and microwave sensor both

detected motion.

Specifications

mFi Ceiling Mount Motion Sensor

Dimensions 134.5 x 134.5 x 30.5 mm

Weight 136 g

Warm Time 2 Minutes

RF Immunity 10V/m at 80 MHz to 2 GHz

Angle of Overview 360°

Cone of Detection 110° Wide Angle

Port (1) mFi RJ45

Mounting

Ceiling‑Mount Bracket (Included)

Mounting Height Up to 4.5 m (15 ft.)

Operating Temperature 0 to 50° C

Operating Humidity 5 to 95% Condensing

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that

can be submerged by water.

WARNING: Avoid using this product during an

electrical storm. There may be a remote risk of

electric shock from lightning.

mFi

™

Ceiling Mount Motion Sensor

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and

current requirements indicated on the manufacturer’s label.

Connection to a different power source than those specified may

result in improper operation, damage to the equipment or pose a

fire hazard if the limitations are not followed.

2. There are no operator serviceable parts inside this equipment.

Service should be provided only by a qualified service technician.

General Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and

warrants that the Products furnished hereunder shall be free from

defects in material and workmanship for a period of one (1) year

from the date of shipment by UBIQUITI NETWORKS under normal use

and operation. UBIQUITI NETWORKS sole and exclusive obligation

under the foregoing warranty shall be to repair or replace, at its

option, any defective Product that fails during the warranty period.

The expense of removal and reinstallation of any item is not included

in this warranty.

The foregoing warranty is exclusive and in lieu of all other

warranties, express or implied, including the implied warranties

of merchantability and fitness for a particular purpose and any

warranties arising from a course of dealing, usage or trade practice

with respect to the products. Repair or replacement in the manner

provided herein shall be the sole and exclusive remedy of Buyer for

breach of warranty and shall constitute fulfillment of all liabilities of

UBIQUITI NETWORKS with respect to the quality and performance

of the Products. UBIQUITI NETWORKS reserves the right to inspect

all defective Products (which must be returned by Buyer to UBIQUITI

NETWORKS factory freight prepaid).

No Products will be accepted for replacement or repair without

obtaining a Return Materials Authorization (RMA) number from

UBIQUITI NETWORKS. Products returned without an RMA number

will not be processed and will be returned to Buyer freight collect.

UBIQUITI NETWORKS shall have no obligation to make repairs or

replacement necessitated by catastrophe, fault, negligence, misuse,

abuse, or accident by Buyer, Buyer’s customers or any other parties.

Compliance

The warranty period of any repaired or replaced Product shall not

extend beyond its original term.

Warranty Conditions

The foregoing warranty shall apply only if:

(I) The Product has not been subjected to misuse, neglect or unusual

physical, electrical or electromagnetic stress, or some other type

of accident.

(II) No modification, alteration or addition has been made to

the Product by persons other than UBIQUITI NETWORKS or

UBIQUITI NETWORK’S authorized representatives or otherwise

approved by UBIQUITI NETWORKS.

(III) The Product has been properly installed and used at all times

in accordance, and in all material respects, with the applicable

Product documentation.

(IV) All Ethernet cabling runs use CAT5 (or above) shielded cabling.

Disclaimer: UBIQUITI NETWORKS does not warrant that the operation

of the products is error‑free or that operation will be uninterrupted.

In no event shall UBIQUITI NETWORKS be responsible for damages or

claims of any nature or description relating to system performance,

including coverage, buyer’s selection of products for buyer’s

application and/or failure of products to meet government or

regulatory requirements.

Returns

In the unlikely event a defect occurs, please work through the dealer

or distributor from which this product was purchased.

Compliance

FCC

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

mFi

™

Ceiling Mount Motion Sensor

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful

interference to radio communications. Operations of this equipment

in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own

expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES‑003.

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that permitted

for successful communication.

This device complies with Industry Canada licence‑exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference

that may cause undesired operation of the device.

Cet appareil numérique de la classe A est confrome à la norme NMB‑

003 Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est

nécessaire pour une communication réussie.

RoHS/WEEE Compliance Statement

Cet appareil est conforme à la norme RSS Industrie Canada exempts

de licence norme(s). Son fonctionnement est soumis aux deux

conditions suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement

du dispositif.

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not

be located or operating in conjunction with any other antenna or

transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

considérant une distance de séparation de toute personnes d’au

moins 20 cm et ne doivent pas être localisé ou utilisé en conflit avec

tout autre antenne ou transmetteur.

CE Marking

CE marking on this product represents the product is in compliance

with all directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the

product and it must follow the CE marking.

RoHS/WEEE Compliance Statement

mFi

™

Ceiling Mount Motion Sensor

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be

disposed of with unsorted municipal waste. The symbol indicates

that this product should be disposed of separately from regular

household waste streams. It is your responsibility to dispose of

this and other electric and electronic equipment via designated

collection facilities appointed by the government or local authorities.

Correct disposal and recycling will help prevent potential negative

consequences to the environment and human health. For more

detailed information about the disposal of your old equipment,

please contact your local authorities, waste disposal service, or the

shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit

diesem Symbol versehen ist , nicht zusammen mit unsortiertem

Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf

hin, dass das Produkt von regulärem Haushaltmüll getrennt

entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät

und andere elektrische und elektronische Geräte über die dafür

zuständigen und von der Regierung oder örtlichen Behörden dazu

bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes

Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen

für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn

Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen,

wenden Sie sich bitte an die örtlichen Behörden oder städtischen

Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt

erworben haben.

Español

La Directiva 2002/96/CE de la UE exige que los equipos que lleven

este símbolo en el propio aparato y/o en su embalaje no deben

eliminarse junto con otros residuos urbanos no seleccionados.

El símbolo indica que el producto en cuestión debe separarse

de los residuos domésticos convencionales con vistas a su

eliminación. Es responsabilidad suya desechar este y cualesquiera

otros aparatos eléctricos y electrónicos a través de los puntos de

RoHS/WEEE Compliance Statement

recogida que ponen a su disposición el gobierno y las autoridades

locales. Al desechar y reciclar correctamente estos aparatos estará

contribuyendo a evitar posibles consecuencias negativas para

el medio ambiente y la salud de las personas. Si desea obtener

información más detallada sobre la eliminación segura de su aparato

usado, consulte a las autoridades locales, al servicio de recogida y

eliminación de residuos de su zona o pregunte en la tienda donde

adquirió el producto.

Français

La directive européenne 2002/96/CE exige que l’équipement sur

lequel est apposé ce symbole sur le produit et/ou son emballage ne

soit pas jeté avec les autres ordures ménagères. Ce symbole indique

que le produit doit être éliminé dans un circuit distinct de celui pour

les déchets des ménages. Il est de votre responsabilité de jeter ce

matériel ainsi que tout autre matériel électrique ou électronique par

les moyens de collecte indiqués par le gouvernement et les pouvoirs

publics des collectivités territoriales. L’élimination et le recyclage en

bonne et due forme ont pour but de lutter contre l’impact néfaste

potentiel de ce type de produits sur l’environnement et la santé

publique. Pour plus d’informations sur le mode d’élimination de

votre ancien équipement, veuillez prendre contact avec les pouvoirs

publics locaux, le service de traitement des déchets, ou l’endroit où

vous avez acheté le produit.

Italiano

La direttiva europea 2002/96/EC richiede che le apparecchiature

contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio

non siano smaltite insieme ai rifiuti urbani non differenziati. Il

simbolo indica che questo prodotto non deve essere smaltito

insieme ai normali rifiuti domestici. È responsabilità del proprietario

smaltire sia questi prodotti sia le altre apparecchiature elettriche

ed elettroniche mediante le specifiche strutture di raccolta indicate

dal governo o dagli enti pubblici locali. Il corretto smaltimento ed

il riciclaggio aiuteranno a prevenire conseguenze potenzialmente

negative per l’ambiente e per la salute dell’essere umano. Per

ricevere informazioni più dettagliate circa lo smaltimento delle

vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare

gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il

negozio nel quale avete acquistato il prodotto.

mFi

™

Ceiling Mount Motion Sensor

Declaration of Conformity

Česky

[Czech]

UBIQUITI NETWORKS tímto prohla uje, e tento

UBIQUITI NETWORKS device, je ve shod se

základními po adavky a dal ími p íslu n mi

ustanoveními sm rnice 1999/5/ES.

Dansk

[Danish]

Undertegnede UBIQUITI NETWORKS erklærer

herved, at følgende udstyr UBIQUITI NETWORKS

device, overholder de væsentlige krav og øvrige

relevante krav i direktiv 1999/5/EF.

Nederlands

[Dutch]

Hierbij verklaart UBIQUITI NETWORKS dat

het toestel UBIQUITI NETWORKS device, in

overeenstemming is met de essentiële eisen

en de andere relevante bepalingen van richtlijn

1999/5/EG.

Bij deze verklaart UBIQUITI NETWORKS dat deze

UBIQUITI NETWORKS device, voldoet aan de

essentiële eisen en aan de overige relevante

bepalingen van Richtlijn 1999/5/EC.

English

Hereby, UBIQUITI NETWORKS, declares that this

UBIQUITI NETWORKS device, is in compliance with

the essential requirements and other relevant

provisions of Directive 1999/5/EC.

Eesti

[Estonian]

Käesolevaga kinnitab UBIQUITI NETWORKS

seadme UBIQUITI NETWORKS device, vastavust

direktiivi 1999/5/EÜ põhinõuetele ja nimetatud

direktiivist tulenevatele teistele asjakohastele

sätetele.

Suomi

[Finnish]

UBIQUITI NETWORKS vakuuttaa täten että

UBIQUITI NETWORKS device, tyyppinen laite on

direktiivin 1999/5/EY oleellisten vaatimusten

ja sitä koskevien direktiivin muiden ehtojen

mukainen.

Français

[French]

Par la présente UBIQUITI NETWORKS déclare

que l’appareil UBIQUITI NETWORKS, device est

conforme aux exigences essentielles et aux

autres dispositions pertinentes de la directive

1999/5/CE.

La pagina sta caricando ...

Ubiquiti MFI-MSC Guida Rapida

Marca: Ubiquiti

Modello: MFI-MSC

Categoria: Rilevatori di movimento

Tipo: Guida Rapida

Scarica il pdf

rapporto

in altre lingue

English: Ubiquiti MFI-MSC Quick start guide
română: Ubiquiti MFI-MSC Ghid de inițiere rapidă

Ubiquiti MFI-MSC Guida Rapida

Ubiquiti MFI-MSC Guida Rapida

in altre lingue

Documenti correlati