Star Micronics 39631810 Manuale del proprietario

Marca: Star Micronics

Modello: 39631810

Categoria: Stampanti POS / mobili

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

SM-T300I Series Mobile Printer Hardware

Mobile Printer

SM-T300I SERIES

Hardware Manual

Federal Communications Commission

Radio Frequency Interference Statement

is device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) is device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

FCC WARNING:

Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable. For RF

interference suppression, if a ferrite core is provided with this device, ax it to the interface cable.

NOTE:

is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful interference in a

residential installation. is equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

CAN ICES-3 (B) / NMB-3 (B)

is equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency

(RF) Exposure rules. is equipment has very low levels of RF energy that it deemed to comply without maximum

permissive exposure evaluation(MPE). But it is desirable that it should be installed and operated keeping the radiator

at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Cet équipement est conforme aux limites d”exposition aux rayonnements énoncées pour un environnement non

contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition dans le Supplément

C à OET65 et d”exposition aux fréquences radioélectriques (RF) CNR-102 de l”IC. Cet équipement émet une énergie

RF très faible qui est considérée conforme sans évaluation de l”exposition maximale autorisée. Cependant, cet

équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le

corps (à l”exception des extrémités : mains, poignets, pieds et chevilles).

English: Hereby, STAR MICRONICS CO.,LTD. declares that this Wireless

Device is in compliance with the essential requirements and

other relevant provisions of Directive 2014/53/EU.

Deutsch:

[German]

Hiermit erklärt STAR MICRONICS CO.,LTD., dass sich das Gerät

Wireless Device in Übereinstimmung mit den grundlegenden

Anforderungen und den übrigen einschlägigen

Bestimmungen der Richtlinie 2014/53/EU bendet.

Svenska:

[Swedish]

Härmed intygar STAR MICRONICS CO.,LTD. att denna

Wireless Device står I överensstämmelse med de väsentliga

egenskapskrav och övriga relevanta bestämmelser som

framgår av direktiv 2014/53/EU.

Español:

[Spanish]

Por medio de la presente STAR MICRONICS CO.,LTD. declara

que el Wireless Device cumple con los requisitos esenciales y

cualesquiera otras disposiciones aplicables o exigibles de la

Directiva 2014/53/UE.

Português:

[Portuguese]

STAR MICRONICS CO.,LTD. declara que este Wireless Device

está conforme com os requisitos essenciais e outras

disposições da Directiva 2014/53/UE.

Français:

[French]

Par la présente STAR MICRONICS CO.,LTD. déclare que

l'appareil Wireless Device est conforme aux exigences

essentielles et aux autres dispositions pertinentes de la

directive 2014/53/UE.

Suomi:

[Finnish]

STAR MICRONICS CO.,LTD. vakuuttaa täten että Wireless

Device tyyppinen laite on direktiivin 2014/53/EU oleellisten

vaatimusten ja sitä koskevien direktiivin muiden ehtojen

mukainen.

Italiano:

[Italian]

Con la presente STAR MICRONICS CO.,LTD. dichiara che questo

Wireless Device è conforme ai requisiti essenziali ed alle altre

disposizioni pertinenti stabilite dalla direttiva 2014/53/UE.

Dansk:

[Danish]

Undertegnede STAR MICRONICS CO.,LTD. erklærer herved, at

følgende udstyr Wireless Device overholder de væsentlige

krav og øvrige relevante krav i direktiv 2014/53/EU.

Nederlands:

[Dutch]

Hierbij verklaart STAR MICRONICS CO.,LTD. dat het toestel

Wireless Device in overeenstemming is met de essentiële

eisen en de andere relevante bepalingen van richtlijn

2014/53/EU.

Eesti:

[Estonian]

Käesolevaga kinnitab STAR MICRONICS CO.,LTD. seadme

Wireless Device vastavust direktiivi 2014/53/EL põhinõuetele

ja nimetatud direktiivist tulenevatele teistele asjakohastele

sätetele.

Ελληνική:

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ STAR MICRONICS CO.,LTD. ΔΗΛΩΝΕΙ ΟΤΙ

Wireless Device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ

ΟΔΗΓΙΑΣ 2014/53/EE.

Slovensky:

[Slovak]

STAR MICRONICS CO.,LTD. týmto vyhlasuje, že Wireless Device

spĺňa základné požiadavky a všetky príslušné ustanovenia

Smernice 2014/53/EÚ.

Slovensko:

[Slovenian]

STAR MICRONICS CO.,LTD. izjavlja, da je ta Wireless Device v

skladu z bistvenimi zahtevami in ostalimi relevantnimi določili

direktive 2014/53/EU.

Česky:

[Czech]

STAR MICRONICS CO.,LTD. tímto prohlašuje, že tento Wireless

Device je ve shodě se základními požadavky a dalšími

príslušnými ustanoveními smernice 2014/53/EU.

Magyar:

[

Hungarian

]

Alulírott, STAR MICRONICS CO.,LTD. nyilatkozom, hogy

a Wireless Device megfelel a vonatkozó alapvetõ

követelményeknek és az 2014/53/EU irányelv egyéb

elõírásainak.

Български:

[Bulgarian]

това Безжично устройство е в съответствие със

задължителните изисквания и другите приложими

разпоредби на Директива 2014/53/EC.

Polski:

[Polish]

Niniejszym STAR MICRONICS CO.,LTD. oświadcza, że

Wireless Device jest zgodny z zasadniczymi wymogami

oraz pozostałymi stosownymi postanowieniami Dyrektywy

2014/53/UE.

Malti:

[Maltese]

Hawnhekk, STAR MICRONICS CO.,LTD., jiddikjara li dan

Wireless Device jikkonforma mal-ħtiġijiet essenzjali u ma

provvedimenti oħrajn relevanti li hemm d-Dirrettiva

2014/53/UE.

Latviski:

[Latvian]

Ar šo STAR MICRONICS CO.,LTD. deklarē, ka Wireless Device

atbilst Direktīvas 2014/53/ES būtiskajām prasībām un citiem

ar to saistītajiem noteikumiem.

Lietuvių :

[Lithuanian]

Šiuo STAR MICRONICS CO.,LTD. deklaruoja, kad šis Wireless

Device atitinka esminius reikalavimus ir kitas 2014/53/ES

Direktyvos nuostatas.

Norsk :

[Norwegian]

STAR MICRONICS CO.,LTD. erklærer herved at utstyret Wireless

Device er i samsvar med de grunnleggende krav og øvrige

relevante krav i direktiv 2014/53/EC.

Română :

[Romanian]

Prin prezenta STAR MICRONICS CO., LTD. declară că acest

dispozitiv este conform cu cerinţele esenţiale și alte prevederi

relevante ale directivei 2014/53/UE.

Hrvatski :

[Croatian]

Ovime Star Micronics CO., LTD. Izjavljuje da je bežični uređaj

u skladu s osnovnim zahtjevima i drugim važnim odredbama

direktive 2014/53/EU.

Italy: e public use is subject to general authorisation by the respective service provider.

Norway: is subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-

Alesund.

Application of Council Directive(s)

1999/5/EC of 9 Mar. 1999

2011/65/EU of 8 Jun 2011

Standard(s) to which Conformity is Declared

RADIO ：

EN 300 328 V1.7.1

EMC ：

EN 301 489-1 V1.9.2

EN 301 489-17 V2.1.1

EN 55022:2010

EN 55024:2010

SAFETY ：

EN60950-1: 2006 / +A12: 2011

EN 62479: 2010

ENVIRONMEN

：

EN 50581: 2012

Manufacturer’s Name Star Micronics Co.,Ltd.

Manufacturer’s Address 20-10 Naka

oshida

Suru

a-ku

Shizuoka-shi

Shizuoka 422-8654 Japan

Importer’s Name Star Micronics Europe Ltd.

Importer’s Address Star House, Peregrine Business Park, Gomm Road,

High Wycombe, Bucks. HP13 7DL, U.K.

Type of Equipment Thermal Printer

Model Name WSP-i350

Ref. R&TTE Radio Report No. ETLE121213.1451-01

Ref. R&TTE EMC Report No. ETLE121213.1448, ETLE121213.1449

Ref. Safety Report No. ETLS121213.0175, ETLE121213.1451-01

Ref. Environ. Report No. WSP-i350-RoHS-01

I , the undersi

ned , hereb

declare that the e

ment s

ecified above

conforms to the above Directive

(

)

and Standard

(

)

Place (Signature)

Date (Full Name)

Year of 1st CE mark (Position)

STAR　MICRONICS CO.,LTD. Head Office

20-10 Nakayoshida, Suruga-ku, Shizuoka-shi, Shizuoka, 422-8654, Japan

Tel. + 81-54-263-1111 Fax. + 81-54-263-1057

STAR Quality Technical Center

18-12 Nakayoshida, Suruga-ku, Shizuoka-shi, Shizuoka, 422-8001, Japan

Tel. + 81-54-263-1303 Fax. + 81-54-263-6650

'10 Technical Manager

Declaration of Conformity

High Wycombe - U.K.

Apr. 01 , 2013 David Pearce

Trademark acknowledgments

SM-T

300I : Star Micronics Co., Ltd.

Notice

is forbidden.

• The contents of this manual are subject to change without notice.

• All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However,

should any errors be detected, STAR would greatly appreciate being informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

• iPad, iPhone, iPod touch and Retina are trademarks of Apple Inc., registered in the U.S. and other countries.

iPad Air, iPad mini and Lightning are trademarks of Apple Inc.

IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

•

Android is a trademark of Google Inc.

• Windows is registered trademarks of Microsoft Corporation.

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

2013-2016 Star Micronics Co., Ltd.

Safety Precautions

Please be sure to read

To use this product in safety, please follow the precautions given below.

WARNING

If you notice smoke, a strange smell, or a strange sound, turn o the power immediately, and remove the

battery pack and battery charger. en contact a Star Micronics dealer.

If any foreign material (metal scraps, water, or other uid) enters the printer, immediately turn o the

printer and remove the battery charger and/or battery pack. en, contact your dealer for advice. Con-

tinued use of the printer could result in a re.

Never attempt to repair the printer yourself. Also do not disassemble or modify the product.

Doing so could lead to injury, re, or electric shock.

Do not touch the tear bar.

- ere is a tear bar inside the paper outlet slot. Not only should you not put your hand in the paper out-

let slot while printing is in progress, never put your hand into the outlet even when printing is not in

progress.

- e printer cover can be opened when replacing the paper. However, since the tear bar is on the inside

of the printer cover, be careful not to place your face or hands too close to the tear bar.

During and immediately aer printing, the area around the thermal head is very hot.

Do not touch it, as you could be burned.

If any battery fluid gets on your skin or clothing, immediately wash the affected area with fresh

water. Otherwise, skin damage may result.

e battery pack may be hot immediately aer the product has been used.

Caution Symbol

This symbol is placed near the thermal head to indicate that it may be hot.

Never touch the thermal head immediately after the printer has been used. Let the thermal

head cool for a few minutes before touching it.

This symbol is placed near the thermal head to indicate that it is easily damaged. Observe

the precautions for handling electrostatic sensitive devices.

Using the Printer

Some semiconductors can be damaged by static electricity.

Be sure to turn o the printer when inserting or removing the battery pack.

Do not drop the printer or hit it against a hard object.

Do not open the printer cover while the printer is printing.

Before you open the printer cover, make sure that printing data is not being sent to the printer.

Do not unplug or plug in a communication cable while the printer is printing or during communication.

Do not touch a communication connector while the printer is printing.

Turn o the printer when you are not using it.

When the printer is used in a low temperature environment or when a PIN pad or other device that needs

electricity is connected to the printer, the battery’s performance will be diminished, and the amount of time

that you can use the printer for may be reduced.

Do not pull out paper while the printer cover is closed.

The heating element and the driver IC of the thermal head are easily damaged. Do not touch them with

metal objects, sandpaper, etc.

Printing quality may suer if the thermal head heating element becomes soiled by being touched with your

hands. Do not touch the thermal head heating element.

ere is a risk of damage to the driver IC of the thermal head from static electricity.

Never directly touch the IC.

Do not operate the printer if there is moisture on the front surface of the head from condensation, etc.

ermal Paper Handling

Only use thermal paper with the designated specications.

e printing quality and working life of the thermal head cannot be guaranteed if any paper other than that

recommended is used. In particular, paper containing [Na+, K+, C1-] may drastically reduce the working

life of the thermal head. Please exercise caution.

Store the thermal paper in a cool, dry, dark location.

Do not rub the thermal paper with a hard object.

Do not leave the thermal paper in contact with plastic lm, an eraser, or adhesive tape for a long period of

time.

Do not stack the thermal paper on fresh diazo copies or wet-type copies.

Do not use chemical glue on the thermal paper.

Do not use thermal paper that has been stored for a long period of time.

Operating Environment for the Printer

Before actually unpacking the printer, you should take a few minutes to think about where you plan

to use it. Remember the following points when doing this.

Do not use the printer in an environment in which it will be subject to strong shaking while it is printing.

Be careful to ensure that the printer is not exposed to direct sunlight.

e appropriate environment for using the printer is described below.

Temperature: -10°C to 50°C

Humidity: 30

% RH to 80 % RH (no condensation)

Do not place the printer near a copying machine or other device that produces a strong electromagnetic eld.

Keep the printer suciently removed from heaters and other sources of heat.

Use the printer in a clean, low-humidity environment that is free from dust.

Avoid using the printer in high-humidity rooms.

We recommend that you unplug the printer from the power outlet whenever you do not plan to use it for

long periods. Because of this, you should locate the printer so that the power outlet it is plugged into is near-

by and easy to access.

Printer Maintenance

Please perform the following maintenance every 6 months.

ermal head

Dip a cotton swab in an alcohol solvent (ethanol, methanol, or isopropyl alcohol), and clean the heating area

of the head.

Platen

While turning the platen, use a so, dry cloth to lightly rub the entire surface of the platen and remove any

foreign objects.

Paper storage unit and the surrounding area

Remove any dirt, dust, pieces of paper, etc., from the paper storage unit.

Card reader

Regularly blow air onto the card reader to remove any dust from the card slot.

Using a Magnetic Card

Do not bring magnets near the card, and do not store the card near a device that produces a magnetic eld

(such as a mobile phone, speaker, or TV).

If you do so, the data on the card may be deleted.

Do not leave the card in a high-temperature environment (such as the dashboard of a car).

If you do so, the card may bend.

Do not touch the card with dirty or wet hands. Also, do not attach adhesive tape or glue to the card.

Failing to follow the above precautions could cause the card to stop working properly.

Table of Contents

1. Product Overview.........................................................................................................1

1.1 Printer & Accessories ................................................................................................................................2

1.2 External Appearance and Part Names ................................................................................................. 3

2. Setup ................................................................................................................................4

2.1 Battery Pack ................................................................................................................................................ 4

2.1.1 Inserting into the Printer or the Battery Holder .........................................................................................4

2.1.2 Charging the Battery .........................................................................................................................................5

2.2 Bluetooth .....................................................................................................................................................8

2.2.1 Pairing ...................................................................................................................................................................8

2.2.2 Auto Connection Function (only for iOS*) ...................................................................................................9

2.3 Loading Paper...........................................................................................................................................10

2.4 Belt Clip ......................................................................................................................................................12

2.4.1 Attaching to the Printer .................................................................................................................................. 12

2.4.2 Using the Belt Clip ............................................................................................................................................12

3. Printer Features ........................................................................................................... 13

3.1 Control Panel ............................................................................................................................................13

3.1.1 Button .................................................................................................................................................................13

3.1.2 Panel Lamp ........................................................................................................................................................13

3.1.3 LCD ......................................................................................................................................................................13

3.2 Self Test ......................................................................................................................................................14

3.2.1 Self Test Procedure ..........................................................................................................................................14

3.2.2 Printing the Bluetooth Device Name and MAC Address .......................................................................14

3.3 Memory Switch Setting (By the buttons on the printer.) ..............................................................15

3.4 HEX Dump Mode ..................................................................................................................................... 22

3.5 Instruction for Auto Power Down(Sleep) Mode .............................................................................. 23

3.6 Card Reading

(Only for Model with Card Reader) ......................................................24

4. Paper ........................................................................................................................... 25

4.1 Paper Specications ................................................................................................................................ 25

4.2 Recommended Paper (Common thermal roll paper) ....................................................................25

4.3 Printing Range .......................................................................................................................................... 25

5. General Specications ............................................................................................... 26

6. Version History .......................................................................................................... 28

This manual supports the following rmware version.

Firmware Version: Ver 4.0 or later

Refer to the appropriate hardware manual which supports the rmware version of your printer.

The rmware version can be conrmed by the self-test. (refer to [3.2 Self Test] of page 14)

- 1 -

1. Product Overview

This printer is perfect for mobile banking systems, retail, POS (point of sale) terminals and other

forms of mobile computing.

The characteristics of this printer are listed below:

•

Pocket size (120 ×130.5 × 58.3 mm) <Model without Card Reader>

•

Extremely light and mobile (442 g)

•

Up to 13 hours of battery-powered operation (12 receipts per hour / Auto Power Down Mode)

•

International Splash/Dust Proof “IP54” Certied

•

1.5m Drop Resistance (Tough Rubber Type Case Design)

*Our test procedure, Not guarantee

•

Support High Quality Print Mode (Double-Stroke Mode)

•

Very silent printing thru direct thermal printing method

•

High speed (75 mm/sec, max.)

•

Standard-equipped dual interface (RS-232C serial interface and Bluetooth Ver. 2.1 + EDR interface)

•

Support for secure Bluetooth communications

Support for Bluetooth Security Mode 3 (PINs of up to 16 digits in length)

Non-discoverable mode can be oered (Factory option)

• Support Magnetic Stripe Reader <Model with Card Reader>

• Support Graphic LCD(128×32 dots) with Blue LED Backlight

• Belt Clip as a standard accessory

• Support text and graphic printing

• Bit-Image(Logo) Store Function “Use Logo Store Tool to store a logo.”

• Drop-in design that makes it easy to load paper

• A printer cover that can be opened with the touch of a button

• Printer cover open sensor & Paper-out sensor

• Flow control : Software (XON/XOFF)

※

Hardware ow control not supported in printer

•

Apple Certied to print directly from iOS devices over Bluetooth





Easy set-up to switch from printing directly from iOS to Android devices

(Operating systems except Mac OS switch automatically)

- 2 -

Shoulder Strap

1.1 Printer & Accessories

The printer is packaged with the following accessories.

If any of these accessories is broken or missing, please contact the dealer

that you bought the product.

The optional items for this printer are listed below.

Battery Pack

Serial Communication Cable

Printer paper samplePrinter

Battery ChargerSafety Instruction Sheet

Extra Battery Pack

Battery Holder

Belt Clip

Car Charger

4 Unit Battery Charger (Special Battery Charger + 4 Unit Holder)

- 3 -

1.2 External Appearance and Part Names

※

Remove the lms if you do not need them.

Platen Gear

Platen

Printer Cover

Cover Open Switch

Thermal Head

Mechanism

Feed Button

LCD

Magnetic Stripe Reader

Error Lamp

Power Lamp

Power Button

Battery Pack

Belt Clip

Charge Connector

Serial Connector

Don’t connect USB mini B cable here.

- 4 -

2. Setup

2.1 Battery Pack

2.1.1 Inserting into the Printer or the Battery Holder

1. Make sure that the printer has been turned o before you insert or remove the battery pack.

2. Insert the battery pack into the back of the printer as in the gure shown below, following the di-

rection of the arrow.

3. To remove the battery back, pull back the hook, and use the opposite procedure from the one you

used to insert the battery pack.

4. The battery pack install into External Battery Cradle.

Insert the battery pack in the direction of the arrow.

Hook

Push the battery pack until

the hock clicks into place.

Lamp(Red) Lamp(Green)

Charging Fully charged

- 5 -

2.1.2 Charging the Battery

Insert the battery pack into the printer to charge it.

Insert the battery charger cable into the printer’s power inlet for charging.

Notes about the Battery Pack

General Battery Characteristics

•

The battery is a consumable and its performance over time will gradually decrease.

•

While not in use, the battery will slowly discharge itself.

Prepare a battery pack that has been charged relatively recently (1 to 2 days earlier).

•

To ensure that the battery lasts for a long time, we recommend that you turn off the printer

whenever possible.

• When used at low temperatures, battery performance will temporarily decline. Be sure to have a

fully-charged spare battery standing by if the printer will operate in a cold environment.

Charging the Battery Pack

• The battery pack can be charged at ambient temperatures between 0 and 40°C.

• The time required to charge the battery pack varies depending on the voltage and the ambient

temperature.

Normally, it takes 4 to 5 hours to charge the battery pack.

• It will take longer to charge the battery pack if you print while charging the battery pack.

• Do not remove the battery pack while it is being charged.

• Fully charge the battery prior to using the printer. Otherwise, the performance of the battery

may be affected.

• There is no need to completely discharge or use up a rechargeable lithium ion battery before re-

charging it.

• It is normal for the battery pack to be hot after it has finished charging or been used.

• Do not recharge a battery pack that has just been fully charged.

Note:

When the battery charger is connected to the printer without the battery pack, the

printer turns on but cannot print.

- 6 -

Battery Pack Life

• The battery can be charged approximately 500 times in the normal temperature range without

losing performance. If an extreme decline in the running time of the battery is noticed, the bat-

tery is reaching the end of its usable life. It is recommended to replace the old battery with a

new one.

Notes about Using the Battery Pack

• Only use a designated battery pack.

• Only use the designated battery charging method.

You cannot use a battery charger other than the designated battery charger.

• Do not throw the battery into a fire, place it near a flame or heating device, or leave it in a hot

environment (under direct sunlight, in a car, etc.).

• Do not use a battery pack that has been dropped or subjected to a shock in some other way.

• Do not disassemble or modify the battery pack.

• Do not short the terminals of the battery pack or get it wet.

Do not place the battery pack in a bag with a small metal object (such as a key).

• If any battery fluid gets on your skin or clothing, immediately wash the affected area with fresh

water. Otherwise, skin damage may result.

Notes about Storing the Battery Pack

• The characteristics of the battery pack may degrade if you store it in a charged state for a long

period of time. If you do not intend to use the battery pack for a while, charge it to approximate-

ly 50 %, and then remove it from the printer.

• If you do not intend to use the battery pack for a long time, be sure to remove it from the printer,

and do not leave it connected to a battery pack holder for external charging.

• Keep the battery out of the reach of children. In addition, be careful that children do not remove

the battery.

• Store the battery pack in a cool place.

* We recommend that you store the battery pack in a dry area with an ambient temperature of

15 to 25 oC.

* Avoid storing the battery in locations with high or extremely low temperatures.

Make sure to follow the instructions below to prevent the battery from

permanent damage.



If you do not intend to use the battery pack for a long period of time, charge it to approximately

50 %, and then remove it from the printer.



During storage, charge the battery pack to approximately 50 % every 3 months.



When the remaining battery level is low, charge the battery as soon as possible.



If the printer turns o due to insucient battery remaining, make sure to recharge the battery

within 15 days.

- 7 -

< For U.S.A. and Canada >

Lithium-Ion batteries are recyclable. You can help preserve our environment by re-

turning your used rechargeable batteries to the collection and recycling location

nearest you. For more information regarding recycling of rechargeable batteries,

call toll free 1-800-822-8837, or visit http://www.rbrc.org/

Battery Disposal and Recycling

A lithium-ion battery is used to power this device. Since the disposal process of batteries varies

from country to country, refer to the appropriate measures mandating the disposal method of

the country in which this device is used.

- 8 -

2.2 Bluetooth

2.2.1 Pairing

1. Press and hold POWER button for approx. 5 seconds, and printer is turned on.

Then, it is ready to pair with another Bluetooth device.

3. If necessary, enter the following information into the terminal that you are using.

PIN: 1234 (default)

Device name: Star Micronics (default)

2. On the host device, tap [Settings]. Set [Bluetooth] to ON.

Select "Star Micronics".

CAUTION

1) For security purposes, we recommend that you change the PIN.

The following utility is required to change the PIN.

Tool name: Star_Bluetooth_Utility.exe

（

for Windows

）

Star Setting Utility

（

for iOS, Android

）

To obtain this utility, please contact with our dealer

For instructions on how to use this utility, please refer to the Bluetooth Setting Utility Software

Manual.

2) If the quantity of data which is printed at once is more than 1M byte on Bluetooth communication,

it would cause the buer to overow and the data to get damaged.

3) For instructions on how to connect with a host device, please refer to your host device user

manual.

iOS

Android

You can test the connectivity with a host device by using StarIO SDK Application which is

available on Apple Store and Google play.

- 9 -

2.2.2 Auto Connection Function (only for iOS*)

When the Bluetooth connection with your iOS device(*1 is disconnected, it is required to establish a

connection by tapping the printer you want to use on the Bluetooth setting screen. This Re Connection

Specication is exactly based on the iOS specications, and this specication is dierent from other OS

such as Android.

The auto connection eliminates this conguration process and automatically sends a request for

connection to the iOS terminal (Host) that the printer previously connected.

See the table below for details of Auto Connection setting.

Auto Connection OFF

Auto Connection ON

(Defalt)

How to re-connect

Turn the printer on and tap the

printer name on the Bluetooth

setting screen of the iOS device.

Af ter powered on, the printer

automatically connects to the

Host that it previously connected.

How to change

the Host

Turn the printer on and tap the

printer name on the Bluetooth

setting screen of the iOS device

you want to use.

Turn the "Bluetooth" function o

on the Bluetooth setting screen

of the host that the printer is

currently connected, and then tap

the printer name on the Bluetooth

setting screen of the iOS device

you want to use.

Use case

A printer is shared with the multiple

host devices.

A printer is always used with one

host device only.

The ON/OFF switching of the auto connection can be performed by operating the printer panel or using

the Star Bluetooth utility in "StarPRNT Intelligence".

For more details on the switching method, refer to "3-3. Memory Switch Setting".

(*): This function is only valid with iOS devices or when the printer is set to [Bluetooth(Auto)].

This function will be invalid regardless of the settings when the printer is set to [Bluetooth(Mac)],

or if you are using a non-iOS device.

(*1: For example, iPhone, iPad and iPod

- 10 -

2.3 Loading Paper

Refer to chapter 4, “Paper” (p. 23), to select roll paper that conforms to the specications.

1. Turn on the printer.

2. Put your nger on the switch for opening the cover, and then open and raise the printer cover.

3. Load the roll paper in the orientation shown in the gure below, and then pull the end of the roll

straight toward you.

4. Press down on both sides of the printer cover to close it rmly.

When you close the printer cover, make sure that it is closed on both sides.

5. Use the tear bar to cut the extra paper.

CAUTION

When the paper is jammed, be sure to open the printer cover before removing the jammed

paper.

Do not under any circumstances try to pull out the jammed paper forcefully while the printer

cover is closed. Doing so may damage parts of the printer.

Printer Cover

Cover Open Switch

La pagina sta caricando ...

Star Micronics 39631810 Manuale del proprietario

Marca: Star Micronics

Modello: 39631810

Categoria: Stampanti POS / mobili

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

SM-T300I Series Mobile Printer Hardware

Scarica il pdf

rapporto

in altre lingue

English: Star Micronics 39631810 Owner's manual

Star Micronics 39631810 Manuale del proprietario

Questo manuale è adatto anche per

Star Micronics 39631810 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti