ProLights ARIA700PROFILE Manuale utente

USER MANUAL

MANUALE UTENTE

ARIA700PROFILE

MOVING HEAD

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.002-02/19

1

ARIA700PROFILE

Packing content

• ARIA700PROFILE

• Mount bracket

• User manual

TABLE OF

CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Using the menu

3. 4 Menu structure

3. 5 Linking

3. 6 DMX addressing

3. 7 DMX mode

3. 8 Wireless

3. 9 Artnet

3. 10 Movement

3. 11 Screen

3. 12 White balance

3. 13 Dimmer mode

3. 14 Fan mode

3. 15 Theatre mode

3. 16 Temperature

3. 17 Auto and manual test

3. 18 Reset

3. 19 Adjust

3. 20 Factory reload

3. 21 Information

3. 22 RDM

3. 23 Connection of the DMX line

3. 24 Construction of the DMX termination

3. 25 Channel DMX

3. 26 Gobos wheels

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

3

5

6

7

8

9

12

13

14

15

16

17

23

24

25

ARIA700PROFILE

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with

.

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modiﬁcations on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system ﬁtted with eﬃcient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the ﬁxture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the ﬁxture in a well ventilated place.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• The maximum temperature that can be reached on the external surface of the ﬁtting, in a thermally

steady state, is high. After power oﬀ, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

ARIA700PROFILE

- 1 - INTRODUCTION

1.1 DESCRIPTION

ARIA700 is a 400W theatrical LED light designed to bring reﬁnement and silence to the stage. Featuring

a custom RGBW engine which delivers an extensive colour palette and an optical system designed to

allow the layering of eﬀects. The ARIA700 puts the theatre into LED.

FEATURES:

• Full spectrum RGBW LED engine for extensive pastel colour palette and HD dimming

• A near-silent operation for use even in front of house

• Animation wheel and full-framing shutters with individual depth and angle control of each blade as

well as module index.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 400W custom RGBW LED

• CT: Tunable 2.000 K ~ 10.000K

• Luminous ﬂux: 6’153 lm

• Lux: (10°) 22’361 lx - (45°) 2’166lx @3 m full

• Lux: (10°) 8’050 lx - (45°) 780lx @5 m full

• Source life expectancy: >50.000 h

OPTICS

• Zoom: 10° - 45° motorised linear zoom

• Lens type: HD anti-reﬂection lenses with achromatic coating

• Focus: motorised with auto-focus

• Other: high-quality ﬂat-ﬁeld projection

COLOUR SYSTEM

• Colour mixing: RGBW / FC

• CTC: CTC control through independent DMX channel

• White presets: 2000 K ~ 8000K

• Colour wheel: virtual colour wheel with presets

DYNAMIC EFFECTS

• Shutter system: 4 shutter blades with position and ±30° angle adjustment, ±45° rotation of the com-

plete framing system

• Animation wheel: animation wheel with CW and CCW rotation

• Rotating gobos: 7 rotating gobos + open, interchangeable, indexing

• Gobo size: outer: 26,7 mm - image: 22 mm - thickness: 0,3 mm

• FX generator: shutter macros with adjustable speed

• Circular prism: 3f with bi-directional rotation, indexing

• Frost: linear 0 - 100% frost ﬁlter

• Iris: 5 - 100% motorised linear iris

BODY

• Pan angle: 540°

• Tilt angle: 270°

• Pan/Tilt resolution: 16 bit

• Feedback: automatic repositioning after accidental movement

• Body: aluminium structure with hi-resistance polycarbonate cover

• Body colour: black

ARIA700PROFILE

4

CONTROL

• Protocols: DMX512, RDM, Art-Net, W-DMX

• DMX channels: 33 / 38 / 39channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for ﬁxture remote monitor and settings

• Display: LCD high resolution colour display with autoﬂip

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: 4 diﬀerent dimming curves available

• Strobe / shutter: 1 - 28 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: ﬂicker free operation

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230V): 463W

• Power consumption (at 120V): 467W

• Output (at 230V): 8 units on a single power line

• Output (at 120V): 4 units on a single power line

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and ﬁxing: any position with quick-lock omega brackets

• Pan / tilt lock: pan / tilt locking for transportation and maintenance

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Data connection: Art-Net RJ45 IN/OUT

• Power connection: Neutrik powerCON TRUE1 IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 408x676x257mm

• Weight: 26kg

Fig.1

676mm/26,31in

408mm/16,06in 257mm/10,11in

Technical drawing

5

ARIA700PROFILE

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

1. MOVING HEAD

2. ROTARY ARM

3. TILT Mechanism Lock and Release

4. PAN Mechanism Lock and Release

5. HANDLE

6. LED INDICATOR "POWER"

7. LED INDICATOR "WDMX"

8. CONTROL PANEL with LCD display

and 4 button used to access the

control panel functions and man-

age them.

9. POWER IN (PowerCON TRUE

IN): for connection to a socket

(100-240V~/50-60Hz) via the sup-

plied mains cable.

10. POWER OUT (PowerCON OUT):

power output for connection of

multiple units in series.

11. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

12. ANTENNA

13. EtherCON connector Signal IN/

OUT

14. DMX IN (3-pole XLR): 1 = ground, 2

= DMX -, 3 = DMX +

15. DMX OUT (5-pole XLR): 1 = ground,

2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

6

7

8

9

10 15

11 14

12

13

1

2

3

5

4

ARIA700PROFILE

6

- 2 - INSTALLATION

2.1 MOUNTING

The ARIA700PROFILE may be set up on a solid and even surface. By means of the ﬁxing facilities of the

baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in ﬁg.3. For

ﬁxing, stable mounting clips are required. According to the ﬁgure, the bolts of the brackets are placed into

the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure

that the unit is ﬁrmly ﬁxed to avoid vibration and slipping while operating. The mounting place must be of

suﬃcient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the ﬁxture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

Fig.3

CLAMP

SAFETY ROPE

OMEGA

7

ARIA700PROFILE

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the ARIA700PROFILE is ready for operation. To

switch oﬀ, disconnect the mains plug from the socket. For a more convenient operation it is recommend-

ed to connect the unit to a socket which can be switched on and oﬀ via light switch.

3.2 BASIC

The control panel of ARIA700PROFILE has a display and 5 buttons for the complete programming and

management of the projector menu (ﬁg.4).

Fig.4 - Functions of the buttons and display icons

UP

DOWN LEFT RIGHT ENTER BATTERY

Increases the value

displayed or passes

to the previous item

in a menu

Decreases the value

displayed or passes

to the next item in

the menu

Return to the top

level

Commute from

units, tens, hundred

in the menu

Confirms the

displayed value,

or activates the

displayed function,

or enters the

successive menu

Used to activate the

backup battery. It

allows to switching

display interface

without main power

CONNECT SETUP ADVANCED INFORMATION

STAND ALONE

ARIA700PROFILE

8

Fig.5 - Reversal of the display

3.3 USING THE MENU

1. Press the ENTER button to access the main menu.

2. Use the UP/DOWN button to select the menu to be used:

• Connect;

• Setup;

• Advanced;

• Information;

3. Press ENTER to display the ﬁrst item in the selected menu.

4. Use the UP/DOWN button to select the menu items.

NOTE - The display can be in one of two conditions: rest status and setting status. When it is in the rest sta-

tus, the display shows the projector’s DMX address. During menu setting status, after a wait time without

any key having been pressed, the display automatically returns to rest status.

It should be noted than when this condition occurs, any possible value that has been modiﬁed but not yet

conﬁrmed with the ENTER button will be cancelled.

Reversal of the display

To activate this function, hold simultaneously for 3 seconds UP and DOWN buttons while the display is in

the rest mode. This status will be memorised and maintained even for the next time it will be switched on.

To return to the initial state, repeat the operation all over again.

9

ARIA700PROFILE

3.4 MENU STRUCTURE

MENU

1 CONNECT

ð

DMX Address

ð

Value (1-512)

DMX Mode

ð

Standard 33CH

Extended 38CH

Extended 39CH

Wireless

ð

Receive

ð

ON/OFF

Receive reset

ð

YES/NO

Wireless to DMX

ð

YES/NO

Ethernet

ð

Universe

ð

0-255

Start Channel

ð

1-512

IP address

ð

2/10.133.139.215

Ethernet to DMX

ð

YES/NO

2 SET UP

ð

Movement

ð

Pan Reverse

ð

YES/NO

Tilt Reverse

ð

YES/NO

Pan Feedbacks

ð

YES/NO

Tilt Feedbacks

ð

YES/NO

Screen

ð

Backlight

ð

Always On/10s/20s/30s

Flip Display

ð

YES/NO/AUTO

Warn Cue

ð

ON/OFF

Key Lock

ð

YES/NO

Fixture

ð

White Balance

ð

OFF

ð

MANUAL (RGBW 125-255)

ð

Dimmer Mode

ð

Off/Dimmer1/Dimmer2/Dimmer3

ð

Fans Mode

ð

Auto Speed/High Speed

ð

Theater Mode

ð

Auto/Silent/Off

ð

Temperature Unit

ð

°C/°F

ð

Auto Test

ð

Auto Test

ð

Manual Test

ð

Pan 000-255

ð

Pan Fine 000-255

ð

Tilt 000-255

ð

Tilt Fine 000-255

ð

P/T Speed 000-255

ð

Dimmer 000-255

ð

Shutter 000-255

ð

Red 000-255

ARIA700PROFILE

10

ð

Green 000-255

ð

Blue 000-255

ð

White 000-255

ð

Gobo 000-255

ð

RGobo 000-255

ð

PrismRot. 000-255

ð

Effect 000-255

ð

REffect 000-255

ð

Focus 000-255

ð

Zoom 000-255

ð

Frost 000-255

ð

Iris 000-255

ð

Fr.shutters Rot. 000-255

ð

Fr.shutter 1 Move. 000-255

ð

Fr.shutter 1 Swiv. 000-255

ð

Fr.shutter 2 Move. 000-255

ð

Fr.shutter 2 Swiv. 000-255

ð

Fr.shutter 3 Move. 000-255

ð

Fr.shutter 3 Swiv. 000-255

ð

Fr.shutter 4 Move. 000-255

ð

Fr.shutter 4 Swiv. 000-255

3 ADVANCED

ð

Reset

ð

All

ð

Pan

ð

Tilt

ð

Gobo

ð

Prism

ð

Effect

ð

Focus

ð

Zoom

ð

Frost

ð

Iris

ð

Fr.shutters Rot.

ð

000-255

ð

Fr.shutter 1 M1

ð

000-255

ð

Fr.shutter 1 M2

ð

000-255

ð

Fr.shutter 2 M1

ð

000-255

11

ARIA700PROFILE

ð

Fr.shutter 2 M2

ð

000-255

ð

Fr.shutter 3 M1

ð

000-255

ð

Fr.shutter 3 M2

ð

000-255

ð

Fr.shutter 4 M1

ð

000-255

ð

Fr.shutter 4 M2

ð

000-255

ð

Adjust

ð

Pan

ð

000-255

ð

Tilt

ð

000-255

ð

Gobo

ð

000-255

ð

RGobo

ð

000-255

ð

Prism

ð

000-255

ð

Effect

ð

000-255

ð

Focus

ð

000-255

ð

Zoom

ð

000-255

ð

Frost

ð

000-255

ð

Iris

ð

000-255

ð

Fr.shutters Rot.

ð

000-255

ð

Fr.shutter 1 M1

ð

000-255

ð

Fr.shutter 1 M2

ð

000-255

ð

Fr.shutter 2 M1

ð

000-255

ð

Fr.shutter 2 M2

ð

000-255

ð

Fr.shutter 3 M1

ð

000-255

ð

Fr.shutter 3 M2

ð

000-255

ð

Fr.shutter 4 M1

ð

000-255

ð

Fr.shutter 4 M2

ð

000-255

ð

Factory Reload

ð

YES/NO

4 INFORMATION

ð

Fixture Time

ð

0-9999

Temperature

ð

58 °C

Fans Speed

ð

**%

Software Vers.

ð

DISP- V1.0

NET-V1.0

CTR1-XY- V1.0

CTR2-MOTOR-V1.0

CTR3-MOTOR-V1.0

CTR4-MOTOR-V1.0

CTR5-MOTOR-V1.0

UID

ð

15D00213****

ARIA700PROFILE

12

3.5 LINKING

Several units may be interconnected in order to control all further slave units to the same eﬀect of the

master unit.

1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the ﬁrst slave unit.

2. Connect the DMX OUT of the ﬁrst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.6 DMX ADDRESSING

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512). Press the ENTER key to conﬁrm the setting.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.7 DMX MODE

The ARIA700PROFILE has 3 DMX channel conﬁgurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to

enter the next menu.

• Select the desired mode and press ENTER to conﬁrm your choice.

• Use the UP/DOWN button to select the desired DMX channel conﬁguration (Standard, Extended 38 CH,

Extended 39 CH), then press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The tables on page 17, 18, 19, 20, 21, 22 show the mode of operation and their values DMX.

3.8 WIRELESS

To enable wireless control mode, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu Wireless.

• Press the UP/DOWN button to scroll through the menu, select the desired function Receive on-oﬀ / Receive

Reset / Wireless to DMX and press ENTER to activate the wireless mode.

• Press the UP/DOWN button to scroll through the menu, select Reset Reset to reset the wireless connec-

tion of the unit.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.9 ARTNET

To enable Artnet mode, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu Ethernet.

• Press the UP/DOWN button to scroll through the menu, select Universe / Start Channel / IP Address / Ethernet

to DMX and press ENTER to activate the mode.

• Press the LEFT button repeatedly to exit the menu and save changes.

13

ARIA700PROFILE

3.10 MOVEMENT

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Movement and press the ENTER but-

ton to enter the next menu.

• Use the UP/DOWN button to select the option proposed and press the ENTER button to conﬁrm the

setting.

- Pan Reverse - Pan rotation in the opposite direction. Select NO to deactivate the function (normal set-

ting); YES to activate the function (Pan Reverse).

- Tilt Reverse - Used for reversing tilt movement. Select NO to deactivate the function (normal setting);

YES to activate the function (Tilt Reverse).

- Pan/Tilt Feedbacks - Reorganization Pan/Tilt position after rolling away. Select NO to deactivate or YES

to activate the function.

• Press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.11 SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto Oﬀ. This feature allows you to automatically turn oﬀ the backlight

after a speciﬁed time that you can set using the arrow buttons. To have the display always on select

Always On or set a value of 01-99 min to turn oﬀ the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select YES to activate or NO to dis-

able this function.

- Warn Cue - Error warning. Use the directional keys to select OFF or ON depending on Whether you

want the display to show error alerts.

- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function

is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-

tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, UP,

DOWN, ENTER. Select YES to activate or NO to disable.

• Press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.12 WHITE BALANCE

White Balance Function. Select the White Balance function to set the white balance by changing the val-

ues (125 - 255) of Red, Green, Blue and White colors.

3.13 DIMMER MODE

Dimmer Function. Select Dimmer Mode and choose and simulate diﬀerent dimming curves. Speciﬁcally,

when set to:

Oﬀ - The brightness increase is linear.

Dimmer 1 - Light intensity control is ﬁner at low level and coarse at high levels.

ARIA700PROFILE

14

Dimmer 2 - Light intensity control is ﬁner at high level and coarse at low levels.

Dimmer 3 - Light intensity control is ﬁner at low and high levels, and coarse to medium levels.

3.14 FAN MODE

For the ARIA700PROFILE you can access the following special functions:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Set Up, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the Fixture menu,then press the ENTER button to proceed.

• Press the UP/DOWN button to scroll the menu, then select Fan Mode and press the ENTER button to

conﬁrm.

• Press the UP/DOWN button to select the Auto Speed/High Speed mode, then press the ENTER button to

conﬁrm the choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.15 THEATRE MODE

For the ARIA700PROFILE you can access the following special functions:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Set Up, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the Fixture menu,then press the ENTER button to proceed.

• Press the UP/DOWN button to scroll the menu, then select Theatre Mode and press the ENTER button to

conﬁrm.

• Press the UP/DOWN button to select the Auto Speed/Silent/Oﬀ, then press the ENTER button to conﬁrm

the choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.16 TEMPERATURE

• Select this function to set the unit of measurement of the temperature shown on the display:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Set Up icon, then press the button

• ENTER to access the next menu.

• Press the UP/DOWN button to select Temperature and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select Temperature unit and press the but-

ton ENTER to conﬁrm.

• Press the UP/DOWN button to select the Celsius/Fahrenheit unit, then press the button ENTER to conﬁrm

the choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.17 AUTO AND MANUAL TEST

Through these menus it is possible to test the functioning of all the functions of the moving head.

3.18 RESET

You can start a preset program to restore the selected function:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Reset and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select the function you wish to reset

15

ARIA700PROFILE

between All, Pan, Tilt, Gobo, Prism, Eﬀect, Focus, Zoom, Frost, Iris, Fr. Shutter Rot., Fr. Shutter1 M1, Fr. Shutter1 M2, Fr.

• Shutter2 M1, Fr. Shutter2 M2, Fr. Shutter3 M1, Fr. Shutter3 M2, Fr. Shutter4 M1, Fr. Shutter4 M2.

• Press the ENTER button to conﬁrm your choice and wait for the recovery of the selected function.

3.19 ADJUST

Adjusts the lamp. This function allows you to modify all the parameters of the lamp: Control, Pan , Tilt, Gobo,

RGobo, Prism, Eﬀect, Focus, Zoom, Frost, Iris, Fr. Shhutter Rot, Fr. Shutter1 M1, Fr. Shutter1 M2, Fr. Shutter2 M1, Fr. Shutter2

M2, Fr. Shutter3 M1, Fr. Shutter3 M2, Fr. Shutter4 M1, Fr. Shutter4 M2 . Press the UP/DOWN button to select one of the

parameters and press ENTER to edit the value (000-255) through the UP/DOWN button.

3.20 FACTORY RELOAD

Select this function to reset the unit to factory settings:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Factory Reload and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select YES or NO, then press the ENTER button to conﬁrm.

3.21 INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Temperature - Through the Temperature function can be displayed the temperature inside the ﬁxture,

near the lamp. The temperature can be displayed in degrees Celsius or Fahrenheit.

- Fans Speed - Through the Fans Speed function you can show on display the fan speed present near the

lamp. Velocity is expressed in RPM (revolutions per minute).

- Software Version - Through Software Version function you can display the currently installed software

version.

- UID - Through the UID function you can display the identiﬁer for RDM control.

• Press the LEFT button repeatedly to exit the menu.

3.22 RDM

With this function you can call up various submenus via RDM.

This device is RDM ready. RDM stands for “Remote Device Management” and makes remote control of de-

vices connected to the DMX-bus possible. Manual settings like adjusting the DMX starting address are no

longer needed. This is especially useful when the device is installed in a remote area. RDM is integrated in

DMX without inﬂuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1 and

2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated in one

DMX line. If DMX splitters are used and RDM control is to be used, these splitters must support RDM. The

number and type of RDM parameters depend on the RDM controller (not included) is used.

ARIA700PROFILE

16

3.23 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty ﬁxture and controller operation.

Over long runs can be necessary to insert a DMX level matching ampliﬁer.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the ﬁrst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.24 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reﬂected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in ﬁgure.

Fig.8

Esempio:

connettore XLR a 3 pin

Fig.7

DMX - OUTPUT

Presa XLR

DMX - INPUT

Spina XLR

Pin1 : Massa -

Schermo

Pin2 : - Negativo

Pin3 : + Positivo

Pin4 : N/C

Pin5 : N/C

17

ARIA700PROFILE

3.25 DMX CONTROL

STD EXT EXT

FUNCTION

DMX

Value

33 Ch 38 Ch 39 Ch

1 1 1

PAN8bit

Pan Coarse 000 - 255

2 2 2

PAN 16bit

Pan Fine 000 - 255

3 3 3

TILT 8bit

Tilt Coarse 000 - 255

4 4 4

TILT 16bit

Tilt Fine 000 - 255

5 5 5

P/T SPEED

Fastest to slowest

Movement with blackout

000 - 250

251 - 255

6 6 6

SHUTTER

No function (shutter open)

Strobe effect slow to fast

No function (shutter open)

Pulse-effect in sequences

No function (shutter open)

Random strobe effect slow to fast

No function (shutter open)

000 - 010

011 - 082

083 - 093

094 - 163

164 - 174

175 - 244

245 - 255

7 7 7

DIMMER 8bit

(0% to 100%) 000 - 255

8 8

DIMMER 16bit

(0% to 100%) 000 - 255

9 9

DIMMER Fade

Snap (0% to 100%) fade out 000 - 255

8 10 10

COLOR FUNCTION

No Function

White presets

Forward Spin

Reverse Spin

Continuous

CTC

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 111

112 - 255

ARIA700PROFILE

18

STD EXT EXT

FUNCTION

DMX

Value

33 Ch 38 Ch 39 Ch

9 11 11

COLOR (No function)

No function 000 - 255

COLOR (White Preset)

White 2000K ~ 2700K

White 2700K ~ 3200K

White 3200K ~ 4200K

White 4200K ~ 5600K

White 5600K ~ 8000K

White 8000K ~ 10000K

000 - 155

156 - 175

176 - 195

196 - 215

216 - 235

236 - 255

COLOR (FW spin)

Rainbow Effect (Slow to Fast) 000 -255

COLOR (RW spin)

Rainbow Effect (Slow to Fast) 000 -255

COLOR

Black

Red

Green

Blue

White

Red=0, Green->up, Blue=full, White=0

Red=0, Green=full, Blue->down, White=0

Red->up, Green=full, Blue=0, White=0

Red=full, Green->down, Blue=0, White=0

Red=full, Green=0, Blue->up, White=0

Red->down, Green=0, Blue=full, White=0

000 - 000

001 - 001

002 - 002

003 - 003

004 - 004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

COLOR (CTC)

CTC adjustment of output color, same

as a “classic” CMY fixture with CTC linear

correction.

000 -255

10 12 12

RED

0~100%

000 - 255

11 13 13

GREEN

0~100%

000 - 255

12 14 14

BLUE

0~100%

000 - 255

13 15 15

WHITE

0~100%

000 - 255

La pagina si sta caricando...

ProLights ARIA700PROFILE Manuale utente

ProLights ARIA700PROFILE Manuale utente

in altre lingue

Documenti correlati

Altri documenti