98/482/EC Declaration
(Applies to products that have CE mark attached)
This equipment has been approved in accordance with Council Decision 98/482/EC for Pan-European single
terminal connection to the public switched telephone network (PSTN). However, due to differences between
the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional
assurance of successful operation on every PSTN network termination point.
Aritech is an Interlogix company
© 2001 Interlogix B.V.
All rights reserved. Interlogix B.V. grants the right to reprint this manual for internal use only.
Interlogix B.V. reserves the right to change information without notice.
www.interlogixinc.com
3CS-175-275-575 Series • LED User Guide
Contents
LED keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Turning on your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Turning on your system in Stay gMode . . . . . . . . . . . . 7
Turning on your system in Away hMode . . . . . . . . . . . 8
Turning off your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bypassing (excluding) zones . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unbypassing (including) zones . . . . . . . . . . . . . . . . . . . . . . . 11
Changing user codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Deleting user codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Resetting fire detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setting the keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Service messages display on the LED keypad . . . . . 17
Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CS-175-275-575 Series • LED User Guide 4
LED keypad
Power (green): When lit, the
system is connected to the mains
power.
Armed (red): When lit, the system
is armed.
Service: When lit, the system
requires service.
Star: Used to enable certain
functions.
Chime: Press to turn the chime on
and off.
Ready (green): When lit, the
system is ready to be turned on.
Fire (red): When lit, the fire zone
has been activated.
Stay: Press to arm part of the
system when in the premises.
Bypass (red): When lit, some zones
are not turned on (bypassed or
excluded).
Away: Press to arm complete
system when leaving the premises.
5CS-175-275-575 Series • LED User Guide
LED keypad
aPower (green). The power LED is on if the system is
connected to the mains and if the battery is okay.
The power LED will flash if the system has a low battery
condition or when the battery is not connected. The power LED
is off if the mains is cut.
bReady (green). The ready LED is on when the system is
ready to arm, and flashes when the system is ready to
force arm. If the LED is off the system cannot be armed,
generally because there is a zone fault.
cFire (red). When the fire LED is lit, a fire zone has been
activated. A rapidly flashing fire LED means that there is a
problem with the fire zone.
gStay. This function key part arms your system. Pressing it
disarms all interior zones but leaves the perimeter
protected.
hAway. Press to arm all zones before leaving.
iBypass. Press to bypass (exclude) zones.
jkNavigation keys. These allow you to scroll
through options.
lChime. Press to turn the chime on and off.
@Hash key. Used to access modules and locations.
$Star. Used to access tasks and enter data.
6CS-175-275-575 Series • LED User Guide
Turning on your system
User Action: Close all protected doors and windows
LED Display: Ready LED is on when all protected zones
and sensors are secure.
LED Display: Ready LED is off and zone LEDs are flashing.
The system is not ready to be turned on, you can exclude
these zones when turning on the system by using the bypass key. See
section “Bypassing and Unbypassing”.
User Action: Type your user code to turn on the system.
LED Display: The armed LED illuminates.
You can now leave the premises.
e S
or
9CS-175-275-575 Series • LED User Guide
Turning off your system
User Action: Type your user code to turn off the system.
LED Display: The armed (red) LED goes off (if programmed to be on),
zone LED(s) go off and the keypad stops buzzing.
The system is now turned off.
If there are open zones, the zone LEDs will flash.
e S
10CS-175-275-575 Series • LED User Guide
Bypassing (excluding) open zones
In the event of a zone fault, you can bypass (exclude) open zones when turning on your system by using the bypass (exclude) key.
User Action: Press I.
User Action: Type your user code, if this requirement has been
programmed by your installer.
LED Display: Open zones are displayed by flashing LEDs.
User Action: Press the zone number(s) you would like to exclude.
User Action: Press I.
LED Display: Zone LEDs stop flashing and ready LED illuminates.
User Action: Type your user code to turn on the system.
e S
i S
e S
i S
à é à ( S
11CS-175-275-575 Series • LED User Guide
Unbypassing (including) zones
User Action: Press I.
User Action: Type your user code, if this requirement has been
programmed by your installer.
User Action: Press the zone number(s) you would like to include.
LED Display: The corresponding zone LED(s) go off indicating
the zone has been unbypassed.
LED Display: Bypassed zones are indicated by flashing LEDs.
User Action: Press I.
User Action: Type your code to turn on the system.
i S
e S
e S
à é à ( S
i S
12CS-175-275-575 Series • LED User Guide
Changing user codes
LED Display: The system is disarmed.
User Action: Press * 5.
User Action: Type a master user code.
LED Display: The OK LED flashes.
User Action: Enter the two digit ID, for example 03,
for the user code that you want to change.
LED Display: The OK LED is STEADY.
User Action: Type the new user code, for example 6543
for a 4-digit user code, 654321 for a 6-digit user code.
e S
$ ( S
e S
à ” S
14CS-175-275-575 Series • LED User Guide
Deleting user codes
LED Display: The system is disarmed.
User Action: Press * 5.
User Action: Enter a master user code.
LED Display: The OK LED flashes.
User Action: Enter the two digit ID, for example 03,
that you want to delete.
User Action: Press the Gfour times (for a 4-digit user code)
or six times (for a 6-digit user code) to delete a user code.
LED Display: The OK LED flashes.
User Action: Press #to exit the User Code Programming Mode.
@ S
$ ( S
gggg S
e S
à ” S
15CS-175-275-575 Series • LED User Guide
Resetting fire detectors
LED Display: The fire LED is lit.
User Action: Type your user code to turn off the system if not already
turned off. This will also silence the bells.
User Action: Press *7 (Fire detector reset). Wait 10 seconds while
the fire detectors are reset.
LED Display: The fire LED will go off if all detectors have been reset.
e S
$ è S
16CS-175-275-575 Series • LED User Guide
Setting the keypad tone
User Action: Press * 0.
User Action: Use up/down arrow to adjust the keypad tone.
j increases the pitch of the tone.
k decreases the pitch of the tone.
LED Display: The Service LED flashes.
User Action: Use #to accept the tone you like.
$ à S
j or k S
@ S
17CS-175-275-575 Series • LED User Guide
Service messages display on the LED keypad
LED Display: The service LED illuminates.
Please contact your installer.
SYSTEM FAULT – Press the 1key. The illuminated zone LED(s) correspond(s) to the system fault(s) below:
1Over Current Fault
2Siren Trouble
3Box Tamper
4Expander Power
5Expander Low Battery
6Expander Box Tamper
7Expander Trouble
8Ground Fault Press #to return to the 1 of 8 service LEDs.
1
LED PROBLEM
$ é S
& S
User Action: Press * 2 to see what is causing
the problem. The corresponding LED illuminates and
the service LED flashes (1is shown here as an
example: system fault).
User Action: Press the key corresponding
to the illuminated LED to get more information.
18CS-175-275-575 Series • LED User Guide
Service messages display on the LED keypad (continued)
ZONE LOSS OF SUPERVISION – Press the 4key
and the zone LED(s) will illuminate showing
which zones have a trouble condition. Press #
to return to the 1 of 8 service LEDs.
4
LED LED
ZONE TROUBLE – Press the 5key and the zone
LED(s) will illuminate showing which zones have
a trouble condition. Press #to return to the 1 of
8 service LEDs.
5
TELEPHONE LINE TROUBLE/LINE CUT – This
LED will illuminate when there is a telephone
line trouble or the telephone line has been cut.
The service LED will remain on until the
telephone fault clears and the user code is
entered.
6
FAILURE TO COMMUNICATE – This LED will
illuminate when there is a failure to
communicate between your system and the
central station.
7
PROBLEM PROBLEM
ZONE TAMPER – Press the 2key and the zone
LED(s) will illuminate showing the zones that
are tampered. Press #to return to the 1 of 8
service LEDs.
2
ZONE LOW BATTERY – Press the 3 key. The
zone LED(s) will illuminate showing the zones
with low battery indication. Press # to return to
the 1 of 8 service LEDs.
3
19CS-175-275-575 Series • LED User Guide
Glossary of terms
Armed The security system is turned on.
Away Mode Turns on all of the security system.
Central station Location which monitors the alarm data sent
during an alarm report.
Chime feature An option that allows the keypad to sound
a ding-dong whenever an entry/exit door is opened.
Event Log A temporary log kept in the memory of the security
system, which contains all the alarms and faults that
occurred between turning your system on and off.
Fire detector Reset The fire detector once activated must be
explicitly reset to become operational again. The system
cannot be armed after a fire alarm until the fire detector
has been reset.
Fire LED A steady fire LED means a fire zone has been activated.
A rapidly flashing fire LED means that a fire zone is in a
trouble condition.
Forced arming An option that allows the system to be armed
with one or more zones open. When the system is ready
to be force armed, the ready LED flashes.
Zones that are not closed do not create an alarm.
Function Key A key dedicated for a particular task.
Group bypass An option that allows the user to bypass
multiple zones with a single operation.
LCD Liquid Crystal Display. This is the text display which gives
you information about your system.
LED Light Emitting Diode. The LEDs on the keypad give system
status information.
Master user code A master arm/disarm code that can also
program parts of the system.
Partitioned system A system divided into multiple areas.
Each area can be controlled by seperate users.
Glossary of terms (continued)
Perimeter The outer edge of the protected area.
Power LED When lit, the system is connected to the mains
power.
Ready LED When lit, the system is ready to be turned on.
Stay Mode Turns on part of the security system.
Tamper If the security system is interfered with, a tamper
is recorded. You should contact your installer.
User code A four or six digit code used to arm or disarm the
system.
Zone An area protected by a group of one or more detection
devices.
14 5119 999-1
ISO 9001 Certified
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Aritech CS-175 Series Manuale utente
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
- English: Aritech CS-175 Series User manual
Altri documenti
-
ADEMCO Security System VISTA-15CN Guida d'installazione
-
-
Risco Agility Manuale utente
-
-
Crow RUNNER 8/64 Guida d'installazione
-
Pyronix Matrix 832 Guida d'installazione
-
Pyronix Matrix 832 Manuale utente
-
-
-