Midea D50-15ED2 Manuale utente

Marca: Midea

Modello: D50-15ED2

Tipo: Manuale utente

Storage Electric Water Heater

The diagram above is just for reference. Please take the

appearance of the actual product as the standard.

Instruction Manual

For Model: D50-15ED2

D80-15ED2

D100-15ED2

Thank you very much for purchasing our water heater.

Before installing and operating your water heater, please

read this manual carefully and keep it for future reference.

The installation and maintenance has to be carried out by qualified professionals or Midea

authorized technicians.

The manufacturer shall not be held responsible for any damage or malfunction caused by wrong

installation or failing to comply with following instructions included in this pamphlet.

For more detailed installation and maintenance guidelines, please refer to below chapters.

TABLE OF CONTENTS

TITLE PAGE

1.Cautions ...........................................................................................................................(2)

2.Product introduction .........................................................................................................(3)

3.Unit installation .................................................................................................................(5)

4.Methods of using ..............................................................................................................(7)

5.Maintenance.....................................................................................................................(9)

6.Troubleshooting..............................................................................................................(10)

7.Produce information with EU regulation ......................................................................... (11)

●

General Remark

The supply socket must be earthed reliably. The rated current of the socket shall not be lower than

10A. The socket and plug shall be kept dry to prevent electrical leakage.

The installation height of the supply socket shall not be lower than 1.8m.

The wall in which the electrical water heater is installed shall be able to bear the load more than two

times of the heater filled fully with water without distortion and cracks. Otherwise, other strengthen-

ing measures shall be adopted.

The pressure relief valve attached with the heater must be installed at the cold water inlet of this

heater(see Fig.1), and make sure it is not exposed in the foggy. The water may be outflowed from

pressure relief valve, so the outflow pipe must open wide in the air; The pressure relief valve need

to be checked and cleaned regularly, so as to make sure it will not be blocked.

Before installing this water heater,check and confirm that the earthing on the supply socket is

reliably grounded. Otherwise, the electrical water heater can not be installed and used. Do not use

extension boards. Incorrect installation and use of this electrical water heater may result in serious

injuries and loss of property.

Special Cautions

Hot water

1. CAUTIONS

●

Cold water (Fig.1)

Pressure relief valve

Thread screw

Drain handle

Pressure release hole

When using the heater for the first time(or the first use after maintenance), the heater can not be

switched on until it has been filled fully with water. When filling the water, at least one of the outlet

valves at the outlet of the heater must be opened to exhaust the air. This valve can be closed after

the heater has been filled fully with water.

The water heater is not intended for use by persons(including children)with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instructions concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the heater.

During heating, there may be drops of water dripping from the pressure release hole of the

pressure relief valve. This is a normal phenomenon. If there is a large amount of water leak, please

contact customer care center for repair. This pressure release hole shall, under no circumstances,

be blocked; otherwise, the heater may be damaged, even resulting in accidents.

The drainage pipe connected to the pressure release hole must be kept sloping downwards.

Since the water temperature inside the heater can reach up to 75, the hot water must not be

exposed to human bodies when it is initially used. Adjust the water temperature to a suitable

temperature to avoid scalding.

If the flexible power supply cord is damaged, the special supply cord provided by the manufacturer

must be selected, and replaced by the professional maintenance personnel.

2. PRODUCT INTRODUCTION

2.1 Nomenclature

D -

NOTE

This manual is applicable to the storage electric water heaters (D *-***) manufactured by

this company.

is the product code of the storage electric water heater;

is the capacity (L);

represents the rated power (*100W);

represents the pattern code (eg : A,B,C...);

represents the extension of pattern (eg : 1,2,3...);

2.2 Technical Performance Parameters

●

If any parts and components of this electrical water heater are damaged please contact customer

care center for repair.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play with the appliance.

The maximum inlet water pressure is 0.5MPa; the minimum inlet water pressure is 0.1MPa, if this

is necessary for the correct operation of the appliance.

The water may drip from the discharge pipe of the pressure-relief device and that this pipe must

be left open to the atmosphere; The pressure-relief device is to be operated regularly to remove

lime deposits and to verify that it is not blocked.

In order to drain away the water inside the inner container, it can be drained away from the

pressure release valve. Twist the thread screw of the pressure release valve off, and lift the drain

handle upwards.(See Fig.1) A discharge pipe connected to the pressure-relief device is to be

installed in a continuously downward direction and in a frost-free environment.

Model

Rated

Voltage

(ACV)

IPX4

0.8

220-240

1500

D30-15ED2

D50-15ED2

D80-15ED2

Rated

Power

(W)

Volume

(L)

Rated

Pressure

(MPa)

Max Of Water

Temperature

(°C)

Protection

Class

Waterproof

Grade

IPX4751500

D100-15ED2 I

2.3 Brief introduction of product structure

2.4 Internal Wire Diagram

WIRING DIAGRAM

(Note:All dimensions are in mm)

Thermal

Cut Out

Thermal

Cut Out

Power

Indicator

Heating Indicator

Thermostat

Heating Element

Power

Brown

Blue

Yellow/Green

Q Q

D30-20ED2 D50-20ED2 D80-20ED2 D100-20ED2

355 355

302 470

250

575

470

250

860

470

183 183

415

365

300

900

570

265

415

550

300

1090

570

265

3. UNIT INSTALLATION

3.1 Installation Instruction

This electrical water heater shall be installed on a solid wall. If the strength of the wall cannot

bear the load equal to two times of the total weight of the heater filled fully with water, it is then

necessary to install a special support.

Incase of hollow bricks wall, ensure to fill it with cement concrete completely.

After selecting a proper location, determine the positons of the two install holes used for expan-

sion bolts with hook, Make two holes in the wall with the corresponding depth by using a

chopping bit with the size matching the expansion bolts attached with the machine, insert the

screws, make the hook upwards, tighten the nuts to fix firmly, and then hang the electrical

water heater on it (see Fig.2).

Install the supply socket in the wall. The requirements for the socket are as follows: 250V/10A,

single phase, three electrodes. It is recommended to placed the socket on the right above the

heater. The height of the socket to the ground shall not be less than 1.8m (see Fig.3).If there

is fault on power cable, it should be replaced by the manufacturers, agencies or qualified person

who is able to do this so as to ensure the safety.

If the bathroom is too small, the heater can be installed at another place. However, in order

to reduce the pipeline heat losses, the installation position of the heater shall be closed to the

location shall be as near as possible to the heater.

(Fig.2)

(Fig.3)

Expansion bolt (with hook)

N (Blue)

Ground

≥1.8m

L (Brown) E (Yellow/Green)

3.2 Pipelines Connection

If the users want to realize a multi-way supply system, refer to the method shown in fig.5 and

fig.6 for connection of the pipelines.

The dimension of each pipe part is G1/2” ; The massive pressure of inlet should use Pa as

the unit; The minimum pressure of inlet should use Pa as the unit.

Connection of pressure relief valve with the heater on the inlet of the water heater.

In order to avoid leakage when connecting the pipelines, the rubber seal gaskets provided with

the heater must be added at the end of the threads to ensure leak proof joints (see Fig.4).

(Fig.4)

(Fig.5)

Pressure relief valve

Water inlet valve

Running water pipeMixing valve

Water pool

Triple joint Shower nozzle

Hot water outlet Cold water inlet

Rubber seal gaskets

Pressure relief valve

Pressure release hole

Joint screw for cold water inlet

Adjusting handle for

mixing valve

Hot

water

outlet

Cold

water

inlet

Hot water

Rubber seal gaskets

VERTICAL INSTALLATION

Power cord

NOTE

Please be sure to use the accessories provided by our company to install this electric

water heater. This electric water heater can not be hung on the support until it has been

confirmed to be firm and reliable. Otherwise, the electric water heater may drop off from

the wall, resulting in damage of the heater, even serious accidents of injury. When

determining the locations of the bolt holes, it shall be ensured that there is a clearance

not less than 0.2m on the right side of the electric heater, to convenient the maintenance

of the heater, if necessary.

(Fig.6)

Pressure relief valve

Water inlet valve

Running water pipeMixing valve

Water pool

Triple joint

Water inlet valve

Shower nozzle

Hot

water

outlet

Cold

water

inlet

4. METHODS OF USING

NOTE

During normal operation, the inlet valve shall be always kept open.

First, open any one of the outlet valves at the outlet of the water heater, then, open the inlet valve.

The water heater gets filled with water. When water flows out of the outlet pipe it implies that the

heater has been filled fully with water, and the outlet valve can be closed.

Insert the supply plug into the supply socket, the indicator will light up this time.

The thermostat will automatically control the temperature. When the water temperature inside the

heater has reached the set temperature, it will switch off automatically, when the water tempera-

ture falls below the set point the heater will be turned on automatically to restore the heating.

●

HORIZONTAL INSTALLATION

Power cord

(Fig.7)

4.1 Operating Of The Unit

“2” is the on/off button, when press, water heater start working, display screen will be

lighted up. Then press again, electricty will be cut off, and display screen will be shut down.

"3" is for temperature adjustment knob with 360 °loop. Temperature increases by clockwise

rotation, and decreases if anticlockwise. During the rotation , display screen " 4" will change

accordingly. When temperature setting meets customers' requirements, stop rotating and

display screen "4" will flash for around 3 seconds, which means temperature has been setted

successfully. After flashing ,display screen "4" value will return to current inner water heater

temperature. After the smart control energy saving mode, the knob can not be adjusted.

“1” button is for selecting mode. When press firstly, display screen “4” will show the six

frequency option( index number “1” means 1500W for one tank, index number “2” means

1500W for dual tank , index number “3” means smart control energy saving mode, index

number “4” means ECO mode, index number “5” means high temperature bacteriostatic

mode, index number “6” means reservation hour setting mode).

"6" is for frequency display. If number " 1" comes out , it means 1500W(only one tank is

heating ) ; If number "2" comes out , it means 1500W (the two inner tank has been being

heated up ), If number " 3" comes out , it means smart control energy saving mode, the

water temperature is automatically changed. The appliance works to reduce the electricity

energy of the user consumption, which allows heat loss to be minimized and energy

savings to be maximized. This function is manually activated.The user can press the

POWER button three times to start the smart control.

From “5” &“7” &“8”(this horizontal strip ) , customer could tell heating status and WiFi

connection status . The light “5” will turn on when power is connected. The light “5“ will blink

, when smart control energy saving mode is started , According the temperature setted, the

light "7" will be shown in red which means water heater is being heated. When inner water

heater temperature reaches the setted value , light "7" will turns off , which means water

heater enter into warm-keeping status. Long press the on key for 3 seconds, and the WiFi

light starts to flash. After the connection is completed, the WiFi light is always on.

WIFI

POWER

"4" could show the current inner water temperature as well as setted temperature value.If no

person operates on water heater , the value in display screen " 4" means current emperature

value .By spinning knob "3" , "4" values will vary accordingly ( i.e temperature setting

process) , when finish temperature setting , "4" values will return back to actual current inner

water heater temperatrue.

5. MAINTENANCE

WARNING

Non-professionals are not allowed to disassemble temperature limiter to reset . Please

contact prefessionals to maintain. Otherwise our company will not take responsiblity if any

quality accident happens because of this

Check the power supply plug and socket frequently to make sure that they have good, reliable

contact and are well grounded without overheating phenomenon.

If the heater is not used for a long time, especially in the regions with low atmospheric tempera-

ture(lower than 0), the water inside the heater shall be drained away. This will prevent the

damage to the heater due to water freezing in the inner container, (Refer Cautions in this manual

for the method to drain away the water from the inner container).

In order to ensure that the water heater operates efficiently for a long time, it is recommended to

clean the inner container and the deposits on the electrical heating components periodically.

It is recommended to examine the magnesium anode protection materials every six months or

so. If all the material has been consumed, please replace with the new material.

●

WARNING

Do cut off power supply before maintenance, to avoid danger like electric shock.

4.2 Error code for serviceman’s use

E2: Dry Ashing---Top up with water and re-heat.

E3: Overheating---Check the heating system or replace it.

E4: Sensor Fault---Check the sensor or replace it.

Temperature limiter cut off electricty if water heater is overheated or thermostat damages.Manual

resetting is needed. Ressetting knob is as follows (see Fig.9).

●

(Fig.9)

Manual reset button

6. TROUBLESHOOTING

NOTE

This products are not equipped with plug. Please contact prefessionals to purchase and

install plug. Parts illustrated in this use and care manual are indicative only, parts provided

with the product may differ with illustrations.This product is intended for household use only.

Specifications are subject to change without notice.

The electrical storage water heater D50-15ED2 of the company MIDEA Ltd. was tested with a declared

load profile of the size “M”

that correspond to the water heating efficiency class “B”

The product fulfills and corresponds to the requirements of the commission regulation standards (No

814/2013) for electrical storage water heater and achieved a water heating energy efficiency of

In accordance with Annex Enercy Efficiency Classes article 1 of the commission regulation (No

812/2013)

The evaluation of the result of this report with respect of conformity with the related commission regulation

(No 812/2013 and 814/2019) is only a part of the conformity assessment to achieve the ErP-Label.

Electricity consumption Qelec, water heating energy efficiency ηwh and mixed water at 40°C (V40).

ηwh=39%

Description Parameter Value Unit

k-Value k

Smart control compliance smart

Smart control factor SCF

Conversion coefficient CC

Ambient correction term Qcor

Referenct energy Qref

Useful energy content QH2O

Correction ratio of reference and useful energy Qref/QH2O

Daily electricity consumption (measured) Qtest_elec

Water temperature at the beginning of the 24h measurement

cycle T3

Water temperature at the end of the 24h measurement cycle T5

Storage volume Mact

Storage volume Cact

Daily electricity consumption (corrected) Qelec

Water heating energy efficiency ηwh

Annual Electricity Consumption AEC

Water heating energy efficiency class

Water temperature without tapping Tset

Average water temperature of inlet cold water θc

Normalised value of the average temperature θp

Calculated volume that delivered hot water of at least 40 V40

kWh

℃

kWh

℃

Sequence of SMART tapping cycles used during the test

Useful energy content of the hot water drawn-off during

smart period Qreference,H2O expressed in kWh:

Useful energy content of the hot water drawn-off during

smart period Qsmart,H2O expressed in kWh:

The weekly electricity consumption with smart controls

The weekly electricity consumption without smart controls

Qelec,week,smart

Qelec,week

Qreference,H2O

Qsmart,H2O

7. Produce information with EU regulation

0.23

23.2

2.5

-0.082

5.845

5.958

0.981

7.423

73.9

71.4

7.417

22.161

22.157

26.662

29.288

39.2

1309

10.4

72.6

M/S/M/S/M

The electrical storage water heater D80-15ED2 of the company MIDEA Ltd. was tested with a declared

load profile of the size “M”

that correspond to the water heating efficiency class “B”

The product fulfills and corresponds to the requirements of the commission regulation standards (No

814/2013) for electrical storage water heater and achieved a water heating energy efficiency of

In accordance with Annex Enercy Efficiency Classes article 1 of the commission regulation (No

812/2013)

The evaluation of the result of this report with respect of conformity with the related commission regulation

(No 812/2013 and 814/2019) is only a part of the conformity assessment to achieve the ErP-Label.

Electricity consumption Qelec, water heating energy efficiency ηwh and mixed water at 40°C (V40).

ηwh=39%

Description Parameter Value Unit

k-Value k

Smart control compliance smart

Smart control factor SCF

Conversion coefficient CC

Ambient correction term Qcor

Referenct energy Qref

Useful energy content QH2O

Correction ratio of reference and useful energy Qref/QH2O

Daily electricity consumption (measured) Qtest_elec

Water temperature at the beginning of the 24h measurement

cycle T3

Water temperature at the end of the 24h measurement cycle T5

Storage volume Mact

Storage volume Cact

Daily electricity consumption (corrected) Qelec

Water heating energy efficiency ηwh

Annual Electricity Consumption AEC

Water heating energy efficiency class

Water temperature without tapping Tset

Average water temperature of inlet cold water θc

Normalised value of the average temperature θp

Calculated volume that delivered hot water of at least 40 V40

kWh

℃

kWh

℃

Sequence of SMART tapping cycles used during the test

Useful energy content of the hot water drawn-off during

smart period Qreference,H2O expressed in kWh:

Useful energy content of the hot water drawn-off during

smart period Qsmart,H2O expressed in kWh:

The weekly electricity consumption with smart controls

The weekly electricity consumption without smart controls

Qelec,week,smart

Qelec,week

Qreference,H2O

Qsmart,H2O

0.23

21.5

2.5

-0.107

5.845

5.958

0.981

7.803

71.9

7.781

22.157

22.156

28.364

31.426

39.0

1315

10.4

72.6

110

M/S/M/S/M

Description Parameter Value Unit

k-Value

Smart control compliance

Smart control factor

Conversion coefficient

Ambient correction term

Referenct energy

Useful energy content

Correction ratio of reference and useful energy

Daily electricity consumption (measured)

Water temperature at the beginning of the 24h measurement

cycle

Water temperature at the end of the 24h measurement cycle

Storage volume

Daily electricity consumption (corrected)

Water heating energy efficiency

Annual Electricity Consumption

Water heating energy efficiency class

Water temperature without tapping

Average water temperature of inlet cold water

Normalised value of the average temperature

Calculated volume that delivered hot water of at least 40

kWh

℃

kWh

℃

Sequence of SMART tapping cycles used during the test

Useful energy content of the hot water drawn-off during

smart period Qreference,H2O expressed in kWh:

Useful energy content of the hot water drawn-off during

smart period Qsmart,H2O expressed in kWh:

The weekly electricity consumption with smart controls

The weekly electricity consumption without smart controls

smart

SCF

Qcor

Qref

QH2O

Qref/QH2O

Qtest_elec

Mact

Cact

Qelec

ηwh

AEC

Tset

θc

θp

V40

Qelec,week,smart

Qelec,week

Qreference,H2O

Qsmart,H2O

The electrical storage water heater D100-15ED2 of the company MIDEA Ltd. was tested with a

declared load profile of the size “M”

that correspond to the water heating efficiency class “B”

The product fulfills and corresponds to the requirements of the commission regulation standards (No

814/2013) for electrical storage water heater and achieved a water heating energy efficiency of

In accordance with Annex Enercy Efficiency Classes article 1 of the commission regulation (No

812/2013)

The evaluation of the result of this report with respect of conformity with the related commission regulation

(No 812/2013 and 814/2019) is only a part of the conformity assessment to achieve the ErP-Label.

Electricity consumption Qelec, water heating energy efficiency ηwh and mixed water at 40°C (V40).

ηwh=41%

0.23

15.82

2.5

-0.02278

5.845

5.958

0.981

6.5851

73.3

72.8

92.1

6.765

22.127

22.100

25.529

27.832

40.8

1258

10.4

68.2

131

M/S/M/S/M

www.midea.com/global

The product is subject to change without notice.

Please keep this manual properly.

Midea Italia S.r.l. a socio unico:

Viale Luigi Bodio 29/37

20158 Milano Italia

midea.com/it

Storage Electric Water Heater

L'immagine sopra indicativa e ha il solo scopo di descrivere il prodotto.

Considerare le informazioni del manuale e le specifiche di

riferimento per le informazioni effettive.

Manuale utente e di installazione

Modelli: D50-15ED2

D80-15ED2

D100-15ED2

Grazie per aver acquistato uno scaldacqua Midea! Questo prodotto

conforme ai pi elevati standard di qualit disponibili. Prima di installare

ed utilizzare il prodotto, leggere questo manuale e conservarlo per le

future necessit di consultazione.

Titolo Pagina

1.Precauzioni.......................................................................................................................(2)

2.Introduzione al prodotto....................................................................................................(3)

3.Installazione dell’unit ........................................................................................................(5)

4.Metodi di utilizzo ..............................................................................................................(7)

5.Manutenzione...................................................................................................................(9)

6.Risoluzione dei problemi ................................................................................................(10)

7.Informazioni sul prodotto in merito alle normative EU.................................................... (11)

●

L'installazione e la manutenzione del prodotto devono essere effettuate da personale qualificato

o da centri assistenza tecnica autorizzati da Midea.

Il produttore non deve essere ritenuto responsabile per qualsiasi danno o malfunzionamento

causato da installazione errata o dal mancato rispetto delle istruzioni incluse in questo libretto.

Per maggiori informazioni sulle condizioni di installazione e manutenzione dei prodotti, fare

riferimento a quanto segue.

Indicazioni generali

TABLE OF CONTENTS

● La presa di alimentazione deve essere collegata alla messa a terra. La corrente nominale della

presa non deve essere inferiore a 10A. La presa e la spina non devono venire in contatto con liquidi

o vapore per evitare cortocircuiti.

● La presa non deve essere posizionata ad un’altezza dal suolo inferiore a 1.8m.

● La parete in cui deve essere installato lo scaldabagno elettrico deve poter sorreggere il doppio

del peso dell'elettrodomestico completamente pieno d'acqua senza deformazioni o crepe.

In caso contrario, necessario adottare delle misure di rinforzo della parete.

● La valvola di sicurezza collegata allo scaldabagno deve essere installata in prossimit della presa

di ingresso dell'acqua fredda. Assicurarsi che la valvola non sia non sia esposta a vapore.

Il prodotto pu essere svuotato mediante lo scarico della valvola di sicurezza: agire sulla leva per

aprire la valvola e consentire lo scarico dell'acqua (Vedi Fig. 1)., rivolta verso il basso e deve

essere previsto un sistema di scarico che non sia soggetto a congelamento.

Prima di installare questo scaldabagno, verificare che l'alimentazione elettrica sia correttamente

connessa e che il collegamento di messa a terra sia adeguato. In caso contrario, lo scaldabagno

non pu essere installato e utilizzato. Non utilizzare prolunghe. La non corretta installazione e lo

scorretto utilizzo di questo scaldabagno possono essere causa di lesioni e danni materiali alle

propriet.

Avvertenze speciali

Hot water

1. Precauzioni

Cold water (Fig.1)

Pressure relief valve

Thread screw

Drain handle

Pressure release hole

● In corrispondenza del primo avviamento del prodotto o dopo un'attivit di manutenzione, l'apparec-

chio non pu essere attivato se non completamente riempito di acqua. Durante il riempimento, il

rubinetto dell'acqua calda deve essere mantenuto costantemente aperto per far fuoriuscire l'aria

dal prodotto. Chiudere il rubinetto quando il prodotto pieno di acqua e procedere all'accensione

dell'unit.

● Lo scaldabagno non destinato all'utilizzo da parte di persone (inclusi bambini) con capacit

motorie, sensoriali o mentali ridotte, o mancanza di competenza o esperienza, a meno che non

siano supervisionati o guidati nell'uso dell'elettrodomestico da una persona responsabile per la loro

sicurezza. Assicurarsi che i bambini non giochino con lo scaldabagno.

● Durante il riscaldamento dell'acqua possibile che alcune gocce di acqua fuoriescano dalla valvola

di sicurezza: Questo fenomeno normale. Se la quantit dell’acqua espulsa maggiore ad alcune

gocce, contattare un centro assistenza tecnica autorizzato dal produttore o il rivenditore. Non

ostruire mai, per nessun motivo il condotto di scarico; se il condotto di scarico ostruito, si possono

determinare gravi danni o incidenti con possibili danni a cose o persone.

● Lo scarico dell’acqua deve essere rivolto verso il basso e deve essere previsto un sistema di

scarico che non sia soggetto a congelamento.

2. Introduzione al prodotto

2.1 Nomenclatura

D -

NOTA

Questo manuale si riferosce esclusivamente ai prodotti commercializzati da Midea Italia

S.r.l. a socio unico.

Codice prodotto: D = Scaldacqua elettrico

Capacit (L)

Potenza elettrica (W Moltiplicato 100)

Codice prodotto (es: A,B,C...);

Serie produttiva (es: 1,2,3...)

Modello

Tensione

Nominale

(VAC)

IPX4

0.8

220-240

1500

D30-15ED2

D50-15ED2

D80-15ED2

D100-15ED2

Potenza

Nominale

(W)

Volume

(L)

Pressione

(MPa)

Temperatura

(℃)

Grado di

protezione

2.2 Dati tecnici prodotti

● La temperatura dell'acqua nello scaldacqua pu raggiungere valori prossimi a 75. Utilizzare un

sistema di miscelazione termostatica dell'acqua per i punti di prelievo, al fine di evitare ustioni e

ferite.

● Se il cavo di alimentazione danneggiato, sospendere l’utilizzo del prodotto in attesa della sua

sostituzione che dovr essere operata da personale qualificato oppure da un centro assistenza

autorizzato dal produttore.

● Se una o pi componenti del sistema necessitano di sostituzione perch danneggiate o degradate,

contattare l'assistenza tecnica Midea.

● Assicurarsi che I bambini non giochino con il prodotto.

● La pressione massima per l'adduzione acqua pari a 0.5Mpa. La pressione minima di adduzione

acqua pari a 0.1Mpa. Utilizzare gli adeguati accorgimenti per assicurare l'erogazione di acqua entro

questi limiti di pressione.

IPX475

220-2401500

93 I

Classe di

protezione

2.3 Schemi dimensionali

(Nota: tutte le dimensioni sono espresse in mm)

2.4 Internal Wire Diagram

Schema elettrico

Protettore

Termico

Protettore

Termico

Indicatore

Presenza

Rete

Indicatore di

riscaldamento

Termostato

Resistenza di

riscaldamento

Modulo di

potenza

Marrone

Blu

Giallo/Verde

Q Q

D30-20ED2 D50-20ED2 D80-20ED2 D100-20ED2

355 355

302 470

250

575

470

250

860

470

183 183

415

365

300

900

570

265

415

550

300

1090

570

265

La pagina sta caricando ...

Midea D50-15ED2 Manuale utente

Marca: Midea

Modello: D50-15ED2

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Midea D50-15ED2 User manual

Midea D50-15ED2 Manuale utente

Midea D50-15ED2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti