Abit IX38 QuadGT Manuale del proprietario

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IX38

QuadGT

Motherboard

Socket 775

User’s Manual

About this Manual:

This user’s manual contains all the information you may

need for setting up this motherboard. To read the user’s

manual of PDF format (readable by Adobe Reader), place

the “Driver & Utility CD” into the CD-ROM drive in your

system. The auto-run screen will appear, click the

“

Manual” tab to enter its submenu. If not, browse the

root directory of the CD-ROM via the File Manager, and

double click the “AUTORUN” file.

 Chipsets: Intel X38 / ICH9R

 FSB 1333 MHz

 Dual Channel DDR2 1066

 Dual PCI-E X16 Slots

 Gigabit LAN

 6x Internal, 2x External SATA

3Gb/s Connectors

 USB 2.0 / IEEE 1394

 7.1-Channel HD Audio

 abit uGuru™

Technology

 abit Silent OTES™ Technology

 External CMOS Clearing

Button

 Quick Power & Reset Button

 Vista HW Ready

ii IX38 QuadGT

Copyright and Warranty Notice

The information in this document is subject to change without notice and does not represent a commitment on part of

the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for

any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special,

incidental or consequential damages arising from any defect or error in this manual or product.

Product names appearing in this manual are for identification purpose only and trademarks and product names or

brand names appearing in this document are the property of their respective owners.

manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer

and authors of this manual.

If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail, we cannot

guarantee any responsibility.

Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE): (The mark and

information are

applicable for EU-member states only.)

The use of the symbol indicates that this product may not be treated as household waste. By Ensurin

g

this product is disposed of correctly, you will help prevent potential ne

g

ative consequences for the

environment and human health, which could otherwise be cause by inappropriate waste handlin

g

of this

product. For more detailed information about recycling of this product, please contact your local city

office, your household waste disposal service or the shop where you purchased the product.

Best Management Practices for Perchlorate Materials:

Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/.

环保使用期限标识说明 (The mark and information are applicable for People's Republic of China only.)

环保使用期限标识是根据<电子信息产品污染控制管理办法>以及<电子信息产品污染控制标识要

求>(SJ/T11364-2006) ，<电子信息产品环保使用期限通则>制定的，适用于中国境内销售的电子

信息产品的标识。

只要按照安全及使用说明内容在正常使用电子信息产品情况下、从生产月期算起，在此期限内产

品中含有的有毒有害物质不致发生外泄或突变、不致对环境造成严重污染或对其人身、财产造成

严重损害。产品正常使用后，要废弃在环保使用年限内或者刚到年限的产品，请根据国家标准采

取适当的方法进行处置。另外，此期限不同于质量/功能的保证期限。

有毒有害物质含有表 (This information is applicable for People's Republic of China only.)

产品中有毒有害物质或元素的名称及含量

有毒有害物质或元素

部件名称

铅(Pb) 汞(Hg) 镉(Cd) 六价铬(Cr(VI)) 多溴联苯(PBB)

多溴二苯醚

(PBDE)

PCB 板 ○ ○ ○ ○ ○ ○

结构件 ○ ○ ○ ○ ○ ○

芯片及其他主动件 × ○ ○ ○ ○ ○

连接器 × ○ ○ ○ ○ ○

被动电子元器件 × ○ ○ ○ ○ ○

焊接金属 ○ ○ ○ ○ ○ ○

线材 ○ ○ ○ ○ ○ ○

光盘 ○ ○ ○ ○ ○ ○

助焊剂、散热膏、标签及

其他耗材

○ ○ ○ ○ ○ ○

○: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。

×: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IX38 QuadGT iii

Contents

1. Hardware Setup ............................................................... 1-1

1.1 Specifications............................................................................... 1-1

1.2 Motherboard Layout ..................................................................... 1-2

1.3 Choosing a Computer Chassis ....................................................... 1-3

1.4 Installing Motherboard ................................................................. 1-3

1.5 Checking Jumper Settings............................................................. 1-4

1.5.1 Internal CMOS Memory Clearing Header and Backup Battery . 1-4

1.6 Connecting Chassis Components ................................................... 1-6

1.6.1 Power Connectors ............................................................... 1-6

1.6.2 Front Panel Switches & Indicators Headers ........................... 1-7

1.6.3 FAN Power Connectors ........................................................ 1-8

1.6.4 Extra Fan Set installation ..................................................... 1-9

1.7 Installing Hardware.................................................................... 1-10

1.7.1 CPU Socket 775................................................................. 1-10

1.7.2 DDR2 Memory Slots........................................................... 1-12

1.7.3 PCI Express X16 Add-on Slots (Install Graphics Card) .......... 1-13

1.8 Connecting Peripheral Devices .................................................... 1-14

1.8.1 Floppy and IDE Disk Drive Connectors ................................ 1-14

1.8.2 Serial ATA Connectors ....................................................... 1-15

1.8.3 Additional USB 2.0 Port Headers......................................... 1-16

1.8.4 Additional IEEE 1394 Port Header....................................... 1-16

1.8.5 Internal Audio Connector ................................................... 1-17

1.8.6 Front Panel Audio Connection Header ................................. 1-17

1.8.7 S/PDIF Output Connection Header...................................... 1-18

1.8.8 PCI and PCI Express X1 Slots ............................................. 1-18

1.8.9 Guru Panel Connection Header........................................... 1-19

1.9 Onboard Indicators and Buttons.................................................. 1-20

1.9.1 POST Code Displayer ......................................................... 1-20

1.9.2 Power Source Indicators .................................................... 1-21

1.9.3 Onboard Buttons ............................................................... 1-21

1.10 Connecting Rear Panel I/O Devices ........................................... 1-22

2. BIOS Setup....................................................................... 2-1

2.1 μGuru

™

Utility .............................................................................. 2-2

2.1.1 OC Guru ............................................................................. 2-2

2.1.2 ABIT EQ.............................................................................. 2-4

2.2 Standard CMOS Features.............................................................. 2-9

2.3 Advanced BIOS Features ............................................................ 2-11

2.4 Advanced Chipset Features......................................................... 2-14

2.5 Integrated Peripherals................................................................ 2-16

2.6 Power Management Setup .......................................................... 2-19

2.7 PnP/PCI Configurations .............................................................. 2-21

2.8 Load Fail-Safe Defaults............................................................... 2-22

2.9 Load Optimized Defaults............................................................. 2-22

2.10 Set Password ........................................................................... 2-22

2.11 Save & Exit Setup..................................................................... 2-22

2.12 Exit Without Saving .................................................................. 2-22

iv IX38 QuadGT

3. Driver & Utility ................................................................. 3-1

3.1 CD-ROM AUTORUN ...................................................................... 3-1

3.2 Q-Install ...................................................................................... 3-2

3.3 Intel Chipset Software Installation Utility ....................................... 3-2

3.4 Intel Matrix Storage Manager........................................................ 3-3

3.5 Audio Driver ................................................................................ 3-3

3.6 LAN Driver................................................................................... 3-4

3.7 JMicron SATA Driver..................................................................... 3-5

3.8 USB 2.0 Driver ............................................................................. 3-5

3.9 abit μGuru ................................................................................... 3-6

3.10 Acrobat Reader 8.0 .................................................................... 3-7

3.11 SATA RAID Driver (for Windows Vista) ........................................ 3-8

3.12 SATA RAID Driver (for Windows XP, 2003, or 2000) ..................... 3-8

4. Multilingual Quick Installation Guide .............................. 4-1

4.1 Français//Guide d'Installation Rapide............................................. 4-1

4.2 Deutsch//Kurze Installationsanleitung............................................ 4-2

4.3 Italiano//Guida all’installazione rapida ........................................... 4-3

4.4 Español//Guía rápida de instalación............................................... 4-4

4.5 Português//Guia de instalação rápida ............................................ 4-5

4.6 Русский//Краткое руководство по установке .............................. 4-6

4.7 Eesti//Kiirpaigaldusjuhend ............................................................ 4-7

4.8 Latviski//Ātrās instalēšanas instrukcija........................................... 4-8

4.9 Lietuvių//Trumpas instaliavimo vadovas ........................................ 4-9

4.10 Polski//Instrukcja szybkiej instalacji........................................... 4-10

4.11 Magyar//Gyorstelepítési útmutató.............................................. 4-11

4.12 Türkçe//Hızlı Kurulum Kılavuzu.................................................. 4-12

4.13 اللغة العربية//دليل التركيب السريع....................... 4-13

4.14 فارسی// راﻩنمای نصب سریع............................................... 4-14

4.15 日本語//クイックインストールガイド ...................................... 4-15

4.16 한국어//빠른 설치 가이드 ....................................................... 4-16

4.17 Bahasa Malaysia//Panduan Pemasangan Ringkas ....................... 4-17

4.18 ไทย//คู่มือการติดตั้งอย่างย่อ ........................................................ 4-18

4.19 繁體中文................................................................................. 4-19

4.19.1 規格............................................................................... 4-19

4.19.2 快速安裝略說.................................................................. 4-20

4.20 简体中文 ................................................................................. 4-21

4.20.1 规格 ............................................................................... 4-21

4.20.2 快速安装略说.................................................................. 4-22

5. Appendix .......................................................................... 5-1

5.1 POST Code Definitions.................................................................. 5-1

5.1.1 AWARD POST Code Definitions............................................. 5-1

5.1.2 AC2005 POST Code Definitions............................................. 5-4

5.2 Troubleshooting (How to Get Technical Support?).......................... 5-5

5.2.1 Q & A ................................................................................. 5-5

5.2.2 Technical Support Form....................................................... 5-8

5.2.3 Contact Information............................................................. 5-9

Hardware Setup

IX38 QuadGT 1-1

1. Hardware Setup

1.1 Specifications

CPU

• Designed for Intel latest 45nm

processor with FSB 1333MHz.

• Support Intel processor of:

Core 2 Extreme Edition / Core 2 Quad /

Core 2 Duo, & Pentium Extreme Edition

/ Pentium Dual Core / Pentium D /

Pentium 4.

Chipset

• Intel X38 / ICH9R

Memory

• 4x 240-pin DIMM slots support

maximum memory capacity up to 8GB.

• Supports Dual Channel DDR2 1066/800

memory.

LAN

• Onboard Gigabit LAN Controller

Audio

• Onboard 7.1-Ch HD Audio Codec

• Supports S/PDIF In/Out

• HDMI Audio Header Ready

Serial ATA

• 6x Internal SATA 3Gb/s connectors

offered by Intel ICH9R support Intel

Matrix Storage Tech (AHCI & RAID 0, 1,

5, and 10).

• 2x External SATA 3Gb/s connectors

offered by JMicron JMB363 support

RAID 0, 1, and JBOD.

IEEE 1394

• Supports 2x IEEE 1394a ports at

400Mb/s transfer rate.

Expansion Slots

• 2x PCI-E X16 Slots (X16 Bandwidth)

• 1x PCI-E X16 Slot (X4 Bandwidth)

• 1x PCI-E X1 Slot

• 2x PCI Slots

Internal I/O Connectors

• 1x Floppy Port

• 1x Ultra ATA 133 IDE Connector

• 6x SATA 3Gb/s Connectors

• 4x USB 2.0 Headers

• 1x IEEE 1394 Header

• 1x FP-Audio Header

• 1x CD-In Connector

• 1x S/PDIF Out Header

• 1x GURU Header

Rear Panel I/O

• 1x PS/2 Keyboard Connector

• 1x PS/2 Mouse Connector

• 1x External CMOS Clearing Button

• 1x Optical S/PDIF In Connector

• 1x Optical S/PDIF Out Connector

• 2x eSATA Connectors

• 1x 7.1-Ch Audio Connector

• 1x IEEE1394 Connector

• 4x USB 2.0 Connectors

• 1x RJ-45 Gigabit LAN Connector

abit Engineered

• abit uGuru

™

Technology

• abit Silent OTES

™

Technology

• External CMOS Clearing Button

• Quick Power & Reset Button

• 100% Low ESR solid capacitor

• Digital PWM

• R-angle SATA connector

RoHS

• 100% Lead-free Process and RoHS

Compliant

Miscellaneous

• ATX Form Factor (305mm x 245mm)

• Vista HW Ready

※ Specifications and information contained herein are subject to change without

notice.

1-2 IX38 QuadGT

1.2 Motherboard Layout

Hardware Setup

IX38 QuadGT 1-3

1.3 Choosing a Computer Chassis

• Choose a chassis big enough to install this motherboard.

• As some features for this motherboard are implemented by cabling connectors on the

motherboard to indicators and switches or buttons on the chassis, make sure your chassis

supports all the features required.

• If there is a possibility of adopting some more hard drives, make sure your chassis has

sufficient power and space for them.

• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O

shield of the chassis matches the I/O port configuration of this motherboard. You can find

an I/O shield specifically designed for this motherboard in its package.

1.4 Installing Motherboard

Most computer chassis have a base with many

mounting holes to allow the motherboard to be

securely attached, and at the same time, prevent

the system from short circuits. There are two

ways to attach the motherboard to the chassis

base: (1) with studs, or (2) with spacers.

Basically, the best way to attach the board is

with studs. Only if you are unable to do this

should you attach the board with spacers. Line up the holes on the board with the mounting

holes on the chassis. If the holes line up and there are screw holes, you can attach the board

with studs. If the holes line up and there are only slots, you can only attach with spacers. Take

the tip of the spacers and insert them into the slots. After doing this to all the slots, you can

slide the board into position aligned with slots. After the board has been positioned, check to

make sure everything is OK before putting the chassis back on.

※ Always power off the computer and unplug the AC power cord before adding or

removing any peripheral or component. Failing to so may cause severe damage

to your motherboard and/or peripherals. Plug in the AC power cord only after

you have carefully checked everything.

To install this motherboard:

1. Locate all the screw holes on the

motherboard and the chassis base.

2. Place all the studs or spacers needed on

the chassis base and have them tightened.

3. Face the motherboard’s I/O ports toward

the chassis’s rear panel.

4. Line up all the motherboard’s screw holes

with those studs or spacers on the chassis.

5. Install the motherboard with screws and

have them tightened.

※ To prevent shorting the PCB circuit,

please REMOVE the metal studs or

spacers if they are already fastened

on the chassis base and are without

mounting-holes on the motherboard

to align with.

Face the chassis’s rear panel.

1-4 IX38 QuadGT

1.5 Checking Jumper Settings

• For a 2-pin jumper, plug the

jumper cap on both pins will

make it CLOSE (SHORT).

Remove the jumper cap, or

plug it on either pin

(reserved for future use) will

leave it at OPEN position.

SHORT OPEN

OPEN

• For 3-pin jumper, pin 1~2 or pin 2~3 can be

shorted by plugging the jumper cap in.

Pin 1~2 SHORT

Pin 2~3 SHORT

1.5.1 Internal CMOS Memory Clearing Header and Backup Battery

The time to clear the CMOS memory occurs when (a)

the CMOS data becomes corrupted, (b) you forgot the

supervisor or user password preset in the BIOS menu,

(c) you are unable to boot-up the system because the

CPU ratio/clock was incorrectly set in the BIOS menu,

or (d) whenever there is modification on the CPU or

memory modules.

This header uses a jumper cap to clear the CMOS

memory and have it reconfigured to the default values

stored in BIOS.

• Pins 1 and 2 shorted

(Default): Normal

operation.

• Pins 2 and 3 shorted:

Clear CMOS memory.

To clear the CMOS memory and load in the default values:

1. Power off the system.

2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper

cap back to its default settings --- pin 1 and pin 2 shorted.

3. Power on the system.

4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS

setup menu right after powering on system.

5. Set the CPU operating speed back to its default or an appropriate value.

6. Save and exit the BIOS setup menu.

※ Another easy way to clear the CMOS memory can be done by pushing the

external “EZ-CCMOS1” button, see the section of “Connecting Rear Panel I/O

Devices” in this manual for detail.

Hardware Setup

IX38 QuadGT 1-5

CMOS Backup Battery:

An onboard battery saves the CMOS memory to keep the BIOS information stays on even after

disconnected your system with power source. Nevertheless, this backup battery exhausts after

some five years. Once the error message like “CMOS BATTERY HAS FAILED” or “CMOS

checksum error” displays on monitor, this backup battery is no longer functional and has to

be renewed.

To renew the backup battery:

1. Power off the system and disconnect with AC power source.

2. Remove the exhausted battery.

3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The “+” side is its

positive polarity.

4. Connect AC power source and power on the system.

5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.

CAUTION:

※ Danger of explosion may arise if the battery is incorrectly renewed.

※ Renew only with the same or equivalent type recommended by the battery

manufacturer.

※ Dispose of used batteries according to the battery manufacturer’s instructions.

1-6 IX38 QuadGT

1.6 Connecting Chassis Components

1.6.1 Power Connectors

These connectors provide the connection from an ATX12V power supply. As the plugs from the

power supply fit in only one orientation, find the correct one and push firmly down into these

foolproof-designed connectors.

For a fully configured system, we recommend that

you use a power supply of ATX12V 2.0 (or newer)

specification compliant and of providing minimum

400W power output capability.

For a fully configured system with two PCI Express

X16 cards installed, a power supply with minimum

500W or more power output is recommended.

※ The following motherboard photos are

served for DEMO only, and may not be

the same type or model as the one

described in this user’s manual.

[ATXPWR1]: 24-pin power connector

You may connect either a 20-pin (ATX12V

1.3) or 24-pin (ATX12V 2.0) power source.

However, it is recommended to connect the

24-pin ATX12V power source to meet the

240VA protection limits.

Plugged from a 24-pin

ATX12V power.

Plugged from a 20-pin

ATX12V power.

[ATX12V1]: 8-pin power connector

This connector supplies +12V power to CPU.

You may connect either a 4-pin ATX12V or

an 8-pin EPS12V power source. However, it

is recommended to connect the 8-pin

EPS12V power source to meet the 240VA

protection limits.

Plugged from a 4-pin

ATX12V power.

Plugged from an 8-pin

EPS12V power.

Hardware Setup

IX38 QuadGT 1-7

1.6.2 Front Panel Switches & Indicators Headers

This header is used for connecting switches and LED indicators on the chassis front panel.

Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure

below stands for positive polarity for the LED connection. Please pay attention when connecting

these headers. A wrong orientation will only result in the LED not lighting, but a wrong

connection of the switches could cause system malfunction.

• HLED (Pin 1, 3):

Connects to the HDD LED cable of chassis front panel.

• RST (Pin 5, 7):

Connects to the Reset Switch cable of chassis front panel.

• SPKR (Pin 13, 15, 17, 19):

Connects to the System Speaker cable of chassis.

• SLED (Pin 2, 4):

Connects to the Suspend LED cable (if there is one) of chassis front panel.

• PWR (Pin 6, 8):

Connects to the Power Switch cable of chassis front panel.

• PLED (Pin 16, 18, 20):

Connects to the Power LED cable of chassis front panel.

1-8 IX38 QuadGT

1.6.3 FAN Power Connectors

These connectors each provide power to the cooling fans installed in your system.

• CPUFAN1: CPU Fan Power Connector

• SYSFAN1: System Fan Power Connector

• AUXFAN1~4: Auxiliary Fan Power Connector

※ These fan connectors are not jumpers. DO NOT place jumper caps on these

connectors.

※ Either a

3-pin

or

4-pin

CPU cooling fan connected to the “CPUFAN1” connector

is still capable of having its fan speed controlled. Please refer to the BIOS setup

route: “PC Health Status”  “ABIT FanEQ Control”  “CPU FAN Type” to select

the one of your own.

Hardware Setup

IX38 QuadGT 1-9

1.6.4 Extra Fan Set installation

※ Proceed with extremely care while installing the extra fan set. DO NOT damage

the motherboard components.

As shown in this photo, it is possible to attach

one mini 40mm(W) x 40mm (H) x 10mm(D)

cooling fan (not included in this motherboard

package) aside the chipset heatsink to increase

the heat dissipating efficiency.

Connect the fan power plug to one of the fan

power connectors.

As shown in this photo, it is possible to attach

one mini 40mm(W) x 40mm (H) x 10mm(D)

cooling fan (not included in this motherboard

package) on top of the PWM heatsink to

increase the heat dissipating efficiency.

Enclosed in the motherboard package you can

find a pair of retention clips. This bundled

accessory is used to hold the fan itself.

Connect the fan power plug to one of the fan

power connectors.

1-10 IX38 QuadGT

1.7 Installing Hardware

※ DO NOT scratch the motherboard when installing hardware. An accidental

scratch of a tiny surface-mount component may seriously damage the

motherboard.

※ In order to protect the contact pins, please pay attention to these notices:

1. A maximum 20 cycles of CPU installation is recommended.

2. Never touch the contact pins with fingers or any object.

3. Always put on the cap when the CPU is not in use.

1.7.1 CPU Socket 775

※ The installation procedures vary with different types of CPU fan-and-heatsink

assembly. The one shown here is served for demo only. For detailed

information on how to install the one you bought, refer to its installation

guidelines.

1. Place the board so that the lever-hook of

the socket is on your left side. Use your left

thumb and forefinger to hold the lever hook,

pull it away from the retention tab. Rotate

the lever to fully open position.

2. Use your right-thumb to raise the load

plate. Lift it up to fully open position.

3. Use your right thumb and forefinger to

grasp the CPU package. Be sure to grasp on

the edge of the substrate, and face the Pin-1

indicator toward the bottom-left side. Aim at

the socket and place the CPU package

vertical down into the socket.

4. Visually inspect if the CPU is seated well

into the socket. The alignment key must be

located in the notch of package.

Hardware Setup

IX38 QuadGT 1-11

5. Use your left hand to hold the load plate,

and use your right thumb to peel the cap off.

The cap plays an important role in

protecting contact pins. In order to

prevent bent pin, PUT ON the cap after

operation or testing.

6. Lower the plate onto the CPU package.

Engage the load lever while gently pressing

down the load plate.

7. Secure the lever with the hook under

retention tab.

8. Place the heatsink and fan assembly onto

the socket. Align the four fasteners toward

the four mounting holes on the motherboard.

9. Press each of the four fasteners down

into the mounting holes. Rotate the fastener

clock-wise to lock the heatsink and fan

assembly into position.

10. Attach the four-pin power plug from the

heatsink and fan assembly to the CPU FAN

connector.

※ A higher fan speed will be helpful for better airflow and heat-dissipation.

Nevertheless, stay alert to not touch any heatsink since a high temperature

generated by the working system is still possible.

1-12 IX38 QuadGT

1.7.2 DDR2 Memory Slots

To reach the performance of Dual Channel DDR2, the following rules must be obeyed:

• For a 2-DIMM dual-channel installation:

Populate DIMM modules of the same type and size on slots [DIMM1]+[DIMM3], or slots

[DIMM2]+[DIMM4].

• For a 4-DIMM dual-channel installation:

Populate 2 DIMM modules of the same type and size on slots [DIMM1]+[DIMM3], and

another 2 DIMM modules of the same type and size on slots [DIMM2]+[DIMM4].

※ [DIMM1] and [DIMM3] slots are made of the same color.

[DIMM2] and [DIMM4] are made of another same color.

Usually there is no hardware or BIOS setup requires after adding or removing memory modules,

but you will have to clear the CMOS memory first if any memory module related problem

occurs.

To install system memory:

1. Power off the computer and unplug the

AC power cord before installing or

removing memory modules.

2. Locate the DIMM slot on the board.

3. Hold two edges of the DIMM module

carefully, keep away from touching its

connectors.

4. Align the notch key on the module with the rib on the slot.

5. Firmly press the module into the slots until the ejector tabs at both sides of the slot

automatically snap into the mounting notch. Do not force the DIMM module in with extra

force as the DIMM module only fits in one direction.

6. To remove the DIMM modules, push the two ejector tabs on the slot outward

simultaneously, and then pull out the DIMM module.

※ Static electricity can damage the electronic components of the computer or

optional boards. Before starting these procedures, ensure that you are

discharged of static electricity by touching a grounded metal object briefly.

Hardware Setup

IX38 QuadGT 1-13

1.7.3 PCI Express X16 Add-on Slots (Install Graphics Card)

This motherboard provides dual PCI Express X16 slots for one or two graphics cards installation

of graphics cards that comply with PCI Express specifications.

One PCI Express graphics card installation:

Insert your PCI Express graphics card into slot

[PCIEXP1].

※ Do not install only one PCI Express

graphics card on slot [PCIEXP2], for

such an act will pull its speed down

to x4 only.

Two PCI Express graphics cards installation:

Install the master graphics card into slot

[PCIEXP1]. Install the slave graphics card

into slot [PCIEXP3].

※ Both the graphics cards must be of

the same GPU family.

※ Make sure your power supply is sufficient to provide the minimum power

required. (For a fully configured system with two PCI Express X16 cards

installed, a power supply with minimum 500W or more power output is

recommended.)

※ Refer to the instruction guide that came with the graphics card on how to run

its dual display mode.

1-14 IX38 QuadGT

1.8 Connecting Peripheral Devices

1.8.1 Floppy and IDE Disk Drive Connectors

The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable.

Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two

connectors on the other end to the floppy disk drives connector. Generally you need only one

floppy disk drive in your system.

※ The red line on the ribbon cable must be aligned with pin-1 on both the FDC1

port and the floppy connector.

Each of the IDE port connects up to two IDE drives

at Ultra ATA/100 mode by one 40-pin, 80-conductor,

and 3-connector Ultra ATA/66 ribbon cables.

Connect the sin

g

le end (blue connector) at the lon

g

er

length of ribbon cable to the IDE port of this board,

the other two ends (gray and black connector) at the

shorter length of the ribbon cable to the connectors

of your hard drives.

※ Make sure to configure the “Master” and “Slave” relation before connecting

two drives by one single ribbon cable. The red line on the ribbon cable must be

aligned with pin-1 on both the IDE port and the hard-drive connector.

Hardware Setup

IX38 QuadGT 1-15

1.8.2 Serial ATA Connectors

Each SATA connector serves as one single channel to connect one SATA device by SATA cable.

To connect SATA device:

1. Attach either end of the signal cable

to the SATA connector on

motherboard. Attach the other end to

the SATA device.

2. Attach the SATA power cable to the

SATA device and connect the other

end from the power supply.

※ The motherboard in this photo is served for DEMO only, and may not be exactly

the same type or model as the one described in this user’s manual.

1-16 IX38 QuadGT

1.8.3 Additional USB 2.0 Port Headers

Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O

panel or the front-mounted USB ports of your chassis.

Pin Pin Assignment Pin Pin Assignment

1 5VDUAL 2 5VDUAL

3 Data0 - 4 Data1 -

5 Data0 + 6 Data1 +

7 Ground 8 Ground

10 NC

※ Make sure the connecting cable bears the same pin assignment.

1.8.4 Additional IEEE 1394 Port Header

Each header supports 1x additional IEEE 1394 port by connecting bracket or cable to the rear

I/O panel or the front-mounted IEEE 1394 port of your chassis.

Pin Pin Assignment Pin Pin Assignment

1 TPA0 + 2 TPA0 -

3 Ground 4 Ground

5 TPB0 + 6 TPB0 -

7 +12V 8 +12V

10 Ground

※ Make sure the connecting cable bears the same pin assignment.

La pagina sta caricando ...

Abit IX38 QuadGT Manuale del proprietario

Abit IX38 QuadGT Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti