Abit Fatal1ty F-190HD Manuale utente

Tipo
Manuale utente

Questo manuale è adatto anche per

Hardware Setup
BIOS Setup
Driver & Utility Multilingual QIG Appendix
F-I90HD
Motherboard
Socket 775
User’s Manual
For more information:
www.abit.com.tw
LGA775 Micro ATX
NB: ATI Radeon Xpress 1250
SB: ATI SB600
1066/800MHz FSB
Dual Channel DDR2
800/667/533
ATI Radeon Xpress 1250
Integrated Graphics
PCI Express Slot
HDMI Support
PCIE Gigabit LAN
4x SATA 3Gb/s RAID
7.1-Channel HD Audio
ii F-I90HD
F-I90HD
User’s Manual
English + Multilingual QIG
P/N: 4310-0000-83
Rev. 2.00, April 2007
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not represent a
commitment on part of the vendor, who assumes no liability or responsibility for any errors that may
appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the quality,
accuracy or fitness for any particular part of this document. In no event shall the manufacturer be
liable for direct, indirect, special, incidental or consequential damages arising from any defect or
error in this manual or product.
Product names appearing in this manual are for identification purpose only and trademarks and
product names or brand names appearing in this document are the property of their respective
owners.
This document contains materials protected under International Copyright Laws. All rights reserved.
No part of this manual may be reproduced, transmitted or transcribed without the expressed written
permission of the manufacturer and authors of this manual.
If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail,
we cannot guarantee any responsibility.
The Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are trademarks of Fatal1ty,
Inc. All rights reserved. Built to Kill is a trademark of PWX, LLC.
© 2007 Universal ABIT Co., Ltd.
All other trademarks are the property of their respective owners.
The Following Information is Only for EU-member States:
Directive 2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE): The use of the symbol indicates that this product may not be
treated as household waste. By Ensurin
g
this product is disposed of correctly,
you will help prevent potential ne
g
ative consequences for the environment
and human health, which could otherwise be cause by inappropriate waste
handling of this product. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
Hardware Setup
BIOS Setup
Driver & Utility Multilingual QIG Appendix
F-I90HD iii
Introduction
FATAL1TY STORY
Who knew that at age 19, I would
be a World Champion PC gamer.
When I was 13, I actually played
competitive billiards in professional
tournaments and won four or five
games off guys who played at the
highest level. I actually thought of
making a career of it, but at that
young age situations change rapidly.
Because I’ve been blessed with
great hand-eye coordination and a
grasp of mathematics (an important
element in video gaming) I
gravitated to that activity.
GOING PRO
I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional
League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one of
the top players in the United States, a company interested in sponsoring me flew me to Sweden
to compete against the top 12 players in the world. I won 18 straight games, lost none, and
took first place, becoming the number one ranked Quake III player in the world in the process.
Two months later I followed that success by traveling to Dallas and defending my title as the
world’s best Quake III player, winning the $40,000 grand prize. Since then I’ve traveled the
globe to compete against the best in the world, winning prizes and acclaim, including the 2005
CPL World Tour Championship in New York City for a $150,000 first place finish.
LIVIN’ LARGE
Since my first big tournament wins, I have been a “Professional Cyberathlete”, traveling the
world and livin’ large with lots of International media coverage on outlets such as MTV, ESPN
and G4TV to name only a few. It's unreal - it's crazy. I’m living a dream by playing video
games for a living. I’ve always been athletic and took sports like hockey and football very
seriously, working out and training hard. This discipline helps me become a better gamer and
my drive to be the best has opened the doors necessary to become a professional.
A DREAM
Now, another dream is being realized – building the ultimate gaming computer, made up of the
best parts under my own brand. Quality hardware makes a huge difference in competitions…a
couple more frames per second and everything gets really nice. It's all about getting the
computer processing faster and allowing more fluid movement around the maps.
My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying
about their equipment, something I’ve preached since I began competing. I don’t want to
worry about my equipment. I want it to be there – over and done with - so I can focus on the
game. I want it to be the fastest and most stable computer equipment on the face of the
planet, so quality is what Fatal1ty brand products will represent.
iv F-I90HD
FATAL1TY PARTNERS
This is just the beginning. We’re already in development for several new products, and I’m
really grateful to all my Fatal1ty partners for helping make my dreams a reality.
I know there is a business side to all of this, but for me the true reward is making products that
are so good I can win with them – and making them available to fellow gamers. Gaming is my
life, and many fellow gamers around the world are also some of my best friends, so giving back
to the gaming community is really important to me.
Johnathan “Fatal1ty” Wendel
Hardware Setup
BIOS Setup
Driver & Utility Multilingual QIG Appendix
F-I90HD v
Contents
1. Hardware Setup ............................................................... 1-1
1.1 Specifications............................................................................... 1-1
1.2 Motherboard Layout ..................................................................... 1-2
1.3 Choosing a Computer Chassis ....................................................... 1-3
1.4 Installing Motherboard ................................................................. 1-3
1.5 Checking Jumper Settings............................................................. 1-4
1.5.1 CMOS Memory Clearing Header and Backup Battery .............. 1-4
1.6 Connecting Chassis Components ................................................... 1-6
1.6.1 ATX Power Connectors......................................................... 1-6
1.6.2 Front Panel Switches & Indicators Headers ........................... 1-7
1.6.3 FAN Power Connectors ........................................................ 1-7
1.7 Installing Hardware...................................................................... 1-8
1.7.1 CPU Socket 775................................................................... 1-8
1.7.2 DDR2 Memory Slots........................................................... 1-10
1.8 Connecting Peripheral Devices .................................................... 1-11
1.8.1 Floppy and IDE Disk Drive Connectors ................................ 1-11
1.8.2 Serial ATA Connectors ....................................................... 1-12
1.8.3 Additional USB 2.0 Port Headers......................................... 1-13
1.8.4 Internal Audio Connector ................................................... 1-14
1.8.5 Front Panel Audio Connection Header ................................. 1-14
1.8.6 PCI and PCI Express X16, X1 Slots ..................................... 1-16
1.8.7 TV-OUT Header................................................................. 1-16
1.9 Onboard Indicators and Buttons.................................................. 1-17
1.9.1 LED Indicators................................................................... 1-17
1.10 Connecting Rear Panel I/O Devices ........................................... 1-18
2. BIOS Setup....................................................................... 2-1
2.1 SoftMenu Setup ........................................................................... 2-2
2.2 Standard CMOS Features.............................................................. 2-3
2.3 Advanced BIOS Features .............................................................. 2-6
2.4 Advanced Chipset Features........................................................... 2-9
2.5 Integrated Peripherals................................................................ 2-10
2.6 Power Management Setup .......................................................... 2-13
2.7 PnP/PCI Configurations .............................................................. 2-15
2.8 PC Health Status ........................................................................ 2-16
2.9 Load Fail-Safe Defaults............................................................... 2-18
2.10 Load Optimized Defaults........................................................... 2-18
2.11 Set Password ........................................................................... 2-18
2.12 Save & Exit Setup..................................................................... 2-18
2.13 Exit Without Saving .................................................................. 2-18
3. Driver & Utility ................................................................. 3-1
3.1 CD-ROM AUTORUN ...................................................................... 3-1
vi F-I90HD
3.2 ATi South Bridge Driver ................................................................ 3-2
3.3 Microsoft.NET Framework............................................................. 3-2
3.4 ATi VGA Driver............................................................................. 3-3
3.5 Realtek LAN Driver....................................................................... 3-3
3.6 Realtek Audio Driver (ATi HDMI)................................................... 3-4
3.7 ATi RAID Driver ........................................................................... 3-6
3.8 USB 2.0 Driver ............................................................................. 3-6
3.9 abit EQ........................................................................................ 3-7
3.10 FlashMenu (BIOS Update Utility) ................................................. 3-8
3.11 SATA RAID Driver (for Windows Vista) ........................................ 3-9
3.12 SATA RAID Driver (for Windows XP, 2003, or 2000) ..................... 3-9
4. Multilingual Quick Installation Guide .............................. 4-1
4.1 Français//Guide d'Installation Rapide............................................. 4-1
4.2 Deutsch//Kurze Installationsanleitung............................................ 4-2
4.3 Italiano//Guida all’installazione rapida ........................................... 4-3
4.4 Español//Guía rápida de instalación............................................... 4-4
4.5 Português//Guia de instalação rápida ............................................ 4-5
4.6 Русский//Краткое руководство по установке .............................. 4-6
4.7 Eesti//Kiirpaigaldusjuhend ............................................................ 4-7
4.8 Latviski//Ātrās instalēšanas instrukcija........................................... 4-8
4.9 Lietuvių//Trumpas instaliavimo vadovas ........................................ 4-9
4.10 Polski//Instrukcja szybkiej instalacji........................................... 4-10
4.11 Magyar//Gyorstelepítési útmutató.............................................. 4-11
4.12 Türkçe//Hızlı Kurulum Kılavuzu.................................................. 4-12
4.13 اللغة العربية//دليل التركيب السريع....................... 4-13
4.14 فارسی// راﻩنمای نصب سریع............................................... 4-14
4.15 日本語//クイックインストールガイド ...................................... 4-15
4.16 한국어//빠른 설치 가이드 ....................................................... 4-16
4.17 Bahasa Malaysia//Panduan Pemasangan Ringkas ....................... 4-17
4.18 ไทย//คู่มือการตดตั้งอยางย่อ ........................................................ 4-18
4.19 繁體中文................................................................................. 4-19
4.19.1 規格............................................................................... 4-19
4.19.2 快速安裝略說.................................................................. 4-20
4.20 简体中文................................................................................. 4-21
4.20.1 规格 ............................................................................... 4-21
4.20.2 快速安装略说.................................................................. 4-22
5. Appendix .......................................................................... 5-1
5.1 Troubleshooting (How to Get Technical Support?).......................... 5-1
5.1.1 Q & A ................................................................................. 5-1
5.1.2 Technical Support Form....................................................... 5-4
5.1.3 Contact Information............................................................. 5-5
Hardware Setup
F-I90HD 1-1
1. Hardware Setup
1.1 Specifications
CPU
Designed for Intel Dual Core LGA775
processor with 1066/800MHz FSB
Support Intel Core 2 Extreme, Core 2
Quad, Core 2 Duo, Pentium EE,
Pentium D, Pentium Dual Core, and
Pentium 4 Processor
Chipset
NB: ATI Radeon Xpress 1250
SB: ATI SB600
Memory
4x 240-pin DIMM slots support
maximum memory capacity up to 16GB
Supports Dual Channel DDR2
800/667/533 Un-buffered ECC/Non-ECC
memory
Graphics
ATI Radeon Xpress 1250 on-chip
(Radeon X700-based 2D/3D graphics)
HDMI
Support HDMI
Support High Definition Video Output
Support 7.1-channel HD audio
LAN
Onboard PCIE Gigabit LAN
Audio
Onboard 7.1-channel HD audio
Serial ATA
4x SATA 3Gb/s supports SATA RAID 0,
1, and 0+1
Expansion Slots
1x PCI-E X16 slot
2x PCI-E X1 slots
1x PCI slot
Internal I/O Connectors
1x Floppy port
1x Ultra ATA 133 IDE connector
4x SATA 3Gb/s connectors
3x USB 2.0 headers
1x FP-Audio header
1x CD-In connector
1x TV-OUT header
Rear Panel I/O
1x PS/2 Keyboard connector
1x PS/2 Mouse connector
1x VGA connector
1x HDMI connector
1x Optical S/PDIF Out connector
1x 7.1-channel Audio connector
4x USB 2.0 connectors
1x RJ-45 Gigabit LAN connector
abit Engineered
abit SoftMenu
Technology
RoHS
100% Lead-free process and RoHS
compliant
Miscellaneous
Micro ATX form factor (244mm x
244mm)
Specifications and information contained herein are subject to change without
notice.
1-2 F-I90HD
1.2 Motherboard Layout
Hardware Setup
F-I90HD 1-3
1.3 Choosing a Computer Chassis
Choose a chassis big enough to install this motherboard.
As some features for this motherboard are implemented by cabling connectors on the
motherboard to indicators and switches or buttons on the chassis, make sure your chassis
supports all the features required.
If there is a possibility of adopting some more hard drives, make sure your chassis has
sufficient power and space for them.
Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O
shield of the chassis matches the I/O port configuration of this motherboard. You can find
an I/O shield specifically designed for this motherboard in its package.
1.4 Installing Motherboard
Most computer chassis have a base with many
mounting holes to allow the motherboard to be
securely attached, and at the same time, prevent
the system from short circuits. There are two
ways to attach the motherboard to the chassis
base: (1) with studs, or (2) with spacers.
Basically, the best way to attach the board is
with studs. Only if you are unable to do this
should you attach the board with spacers. Line up the holes on the board with the mounting
holes on the chassis. If the holes line up and there are screw holes, you can attach the board
with studs. If the holes line up and there are only slots, you can only attach with spacers. Take
the tip of the spacers and insert them into the slots. After doing this to all the slots, you can
slide the board into position aligned with slots. After the board has been positioned, check to
make sure everything is OK before putting the chassis back on.
Always power off the computer and unplug the AC power cord before adding or
removing any peripheral or component. Failing to so may cause severe damage
to your motherboard and/or peripherals. Plug in the AC power cord only after
you have carefully checked everything.
To install this motherboard:
1. Locate all the screw holes on the
motherboard and the chassis base.
2. Place all the studs or spacers needed on
the chassis base and have them tightened.
3. Face the motherboard’s I/O ports toward
the chassis’s rear panel.
4. Line up all the motherboard’s screw holes
with those studs or spacers on the chassis.
5. Install the motherboard with screws and
have them tightened.
To prevent shorting the PCB circuit,
please REMOVE the metal studs or
spacers if they are already fastened
on the chassis base and are without
mounting-holes on the motherboard
to align with.
Face the chassis’s rear panel.
1-4 F-I90HD
1.5 Checking Jumper Settings
For a 2-pin jumper, plug the
jumper cap on both pins will
make it CLOSE (SHORT).
Remove the jumper cap, or
plug it on either pin
(reserved for future use) will
leave it at OPEN position.
SHORT OPEN
OPEN
For 3-pin jumper, pin 1~2 or pin 2~3 can be
shorted by plugging the jumper cap in.
Pin 1~2 SHORT
Pin 2~3 SHORT
1.5.1 CMOS Memory Clearing Header and Backup Battery
The time to clear the CMOS memory occurs when (a)
the CMOS data becomes corrupted, (b) you forgot the
supervisor or user password preset in the BIOS menu,
(c) you are unable to boot-up the system because the
CPU ratio/clock was incorrectly set in the BIOS menu,
or (d) whenever there is modification on the CPU or
memory modules.
This header uses a jumper cap to clear the CMOS
memory and have it reconfigured to the default values
stored in BIOS.
Pins 1 and 2 shorted
(Default): Normal
operation.
Pins 2 and 3 shorted:
Clear CMOS memory.
To clear the CMOS memory and load in the default values:
1. Power off the system.
2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper
cap back to its default settings --- pin 1 and pin 2 shorted.
3. Power on the system.
4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS
setup menu right after powering on system.
5. Set the CPU operating speed back to its default or an appropriate value.
6. Save and exit the BIOS setup menu.
Hardware Setup
F-I90HD 1-5
CMOS Backup Battery:
An onboard battery saves the CMOS memory to keep the BIOS information stays on even after
disconnected your system with power source. Nevertheless, this backup battery exhausts after
some five years. Once the error message like “CMOS BATTERY HAS FAILED” or “CMOS
checksum error” displays on monitor, this backup battery is no longer functional and has to
be renewed.
To renew the backup battery:
1. Power off the system and disconnect with AC power source.
2. Remove the exhausted battery.
3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The “+” side is its
positive polarity.
4. Connect AC power source and power on the system.
5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.
CAUTION:
Danger of explosion may arise if the battery is incorrectly renewed.
Renew only with the same or equivalent type recommended by the battery
manufacturer.
Dispose of used batteries according to the battery manufacturer’s instructions.
1-6 F-I90HD
1.6 Connecting Chassis Components
1.6.1 ATX Power Connectors
These connectors provide the connection from an ATX power supply. As the plugs from the
power supply fit in only one orientation, find the correct one and push firmly down into these
connectors.
ATXPWR1: ATX 24-Pin Power Connector
The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector.
Connect from pin-1 for either type. However, a 20-pin power supply may cause the system
unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W
or higher is recommended.
ATX12V1: ATX 12V 4-Pin Power Connector
This connector supplies power to CPU. The system will not start without connecting power to
this one.
Hardware Setup
F-I90HD 1-7
1.6.2 Front Panel Switches & Indicators Headers
This header is used for connecting switches and
LED indicators on the chassis front panel.
Watch the power LED pin position and orientation.
The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection.
Please pay attention when connecting these
headers. A wrong orientation will only result in the
LED not lighting, but a wrong connection of the
switches could cause system malfunction.
HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis
front panel.
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis
front panel.
SPKR (Pin 13, 15, 17, 19):
Connects to the System Speaker cable of
chassis.
SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there
is one) of chassis front panel.
PWR (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
1.6.3 FAN Power Connectors
These connectors each provide power to the
cooling fans installed in your system.
CPUFAN1: CPU Fan Power Connector
SYSFAN1: System Fan Power
Connector
AUXFAN1~2: Auxiliary Fan Power
Connector
.
These fan connectors are not
jumpers. DO NOT place jumper
caps on these connectors.
1-8 F-I90HD
1.7 Installing Hardware
DO NOT scratch the motherboard when installing hardware. An accidental
scratch of a tiny surface-mount component may seriously damage the
motherboard.
In order to protect the contact pins, please pay attention to these notices:
1. A maximum 20 cycles of CPU installation is recommended.
2. Never touch the contact pins with fingers or any object.
3. Always put on the cap when the CPU is not in use.
1.7.1 CPU Socket 775
The installation procedures vary with different types of CPU fan-and-heatsink
assembly. The one shown here is served for demo only. For detailed
information on how to install the one you bought, refer to its installation
guidelines.
1. Place the board so that the lever-hook of
the socket is on your left side. Use your left
thumb and forefinger to hold the lever hook,
pull it away from the retention tab. Rotate
the lever to fully open position.
2. Use your right-thumb to raise the load
plate. Lift it up to fully open position.
3. Use your right thumb and forefinger to
grasp the CPU package. Be sure to grasp on
the edge of the substrate, and face the Pin-1
indicator toward the bottom-left side. Aim at
the socket and place the CPU package
vertical down into the socket.
4. Visually inspect if the CPU is seated well
into the socket. The alignment key must be
located in the notch of package.
Hardware Setup
F-I90HD 1-9
5. Use your left hand to hold the load plate,
and use your right thumb to peel the cap off.
The cap plays an important role in
protecting contact pins. In order to
prevent bent pin, PUT ON the cap after
operation or testing.
6. Lower the plate onto the CPU package.
Engage the load lever while gently pressing
down the load plate.
7. Secure the lever with the hook under
retention tab.
8. Place the heatsink and fan assembly onto
the socket. Align the four fasteners toward
the four mounting holes on the motherboard.
9. Press each of the four fasteners down
into the mounting holes. Rotate the fastener
clock-wise to lock the heatsink and fan
assembly into position.
10. Attach the four-pin power plug from the
heatsink and fan assembly to the CPU FAN
connector.
A higher fan speed will be helpful for better airflow and heat-dissipation.
Nevertheless, stay alert to not touch any heatsink since a high temperature
generated by the working system is still possible.
1-10 F-I90HD
1.7.2 DDR2 Memory Slots
To reach the performance of Dual Channel DDR2, the following rules must be obeyed:
For a 2-DIMM dual-channel installation:
Populate DIMM modules of the same type and size on slots [DIMM1]+[DIMM3], or slots
[DIMM2]+[DIMM4].
For a 4-DIMM dual-channel installation:
Populate 2 DIMM modules of the same type and size on slots [DIMM1]+[DIMM3], and
another 2 DIMM modules of the same type and size on slots [DIMM2]+[DIMM4].
[DIMM1] and [DIMM3] slots are made of the same color.
[DIMM2] and [DIMM4] are made of another same color.
Usually there is no hardware or BIOS setup required after adding or removing
memory modules, but you will have to clear the CMOS memory first if any
memory module related problem occurs.
This motherboard does not support DDR2 memory modules of X4 device
width.
To install system memory:
1. Power off the computer and unplug the
AC power cord before installing or
removing memory modules.
2. Locate the DIMM slot on the board.
3. Hold two edges of the DIMM module
carefully, keep away from touching its
connectors.
4. Align the notch key on the module with
the rib on the slot.
5. Firmly press the module into the slots until the ejector tabs at both sides of the slot
automatically snap into the mounting notch. Do not force the DIMM module in with extra
force as the DIMM module only fits in one direction.
6. To remove the DIMM modules, push the two ejector tabs on the slot outward
simultaneously, and then pull out the DIMM module.
Static electricity can damage the electronic components of the computer or
optional boards. Before starting these procedures, ensure that you are
discharged of static electricity by touching a grounded metal object briefly.
Hardware Setup
F-I90HD 1-11
1.8 Connecting Peripheral Devices
1.8.1 Floppy and IDE Disk Drive Connectors
The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable.
Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two
connectors on the other end to the floppy disk drives connector. Generally you need only one
floppy disk drive in your system.
The red line on the ribbon cable must be aligned with pin-1 on both the FDC1
port and the floppy connector.
Each of the IDE port connects up to two IDE drives
at Ultra ATA/100 mode by one 40-pin, 80-conductor,
and 3-connector Ultra ATA/66 ribbon cables.
Connect the sin
g
le end (blue connector) at the lon
g
er
length of ribbon cable to the IDE port of this board,
the other two ends (gray and black connector) at the
shorter length of the ribbon cable to the connectors
of your hard drives.
Make sure to configure the “Master” and “Slave” relation before connecting
two drives by one single ribbon cable. The red line on the ribbon cable must be
aligned with pin-1 on both the IDE port and the hard-drive connector.
1-12 F-I90HD
1.8.2 Serial ATA Connectors
Each SATA connector serves as one single channel to connect one SATA device by SATA cable.
The RAID 0/1/0+1 configuration is also possible by the combination of disk arrays through
these SATA connectors:
For more information on how to configure the function mode for SATA, please refer to the item
“OnChip SATA Mode” in the BIOS setup menu of “OnChip IDE Device”.
To connect SATA device:
1. Attach either end of the signal cable
to the SATA connector on
motherboard. Attach the other end to
the SATA device.
2. Attach the SATA power cable to the
SATA device and connect the other
end from the power supply.
The motherboard in this photo is served for DEMO only, and may not be the
same type or model as the one described in this user’s manual.
Hardware Setup
F-I90HD 1-13
1.8.3 Additional USB 2.0 Port Headers
Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O
panel or the front-mounted USB ports of your chassis.
Pin Pin Assignment Pin Pin Assignment
1 VCC 2 VCC
3 Data0 - 4 Data1 -
5 Data0 + 6 Data1 +
7 Ground 8 Ground
10 NC
Make sure the connecting cable bears the same pin assignment.
1-14 F-I90HD
1.8.4 Internal Audio Connector
This connector connects to the audio output of internal CD-ROM drive or add-on card.
1.8.5 Front Panel Audio Connection Header
This header provides the front panel connection for HD (High Definition)
Audio, yet for AC’97 Audio CODEC connection, you must carefully check the
pin assignment before connecting from the front panel module. An incorrect
connection may cause malfunction or even damage the motherboard.
Please do not connect the “Ground” cable or “USB VCC” cable
from the front panel module to the Pin 4 “AVCC” of this header.
Pin
Pin Assignment
(HD AUDIO)
Pin
Pin Assignment
(AC’97 AUDIO)
1 MIC2 L 1 MIC In
2 AGND 2 GND
3 MIC2 R 3 MIC Power
4 AVCC 4NC
5 FRO-R 5 Line Out (R)
6 MIC2_JD 6 NC
7F_IO_SEN 7 NC
9 FRO-L 9 Line Out (L)
10 LINE2_JD 10 NC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Abit Fatal1ty F-190HD Manuale utente

Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue