Gigabyte 5222 Manuale utente

When you installing AGP card, please make sure the following notice

is fully understood and practiced. If your AGP card has "AGP 4X/8X

(1.5V) notch"(show below), please make sure your AGP card is AGP

4X/8X.

Caution: AGP 2X card is not supported by nVIDIA

®

nForce

™

2 400. You

might experience system unable to boot up normally. Please

insert an AGP Pro 4X/8X card.

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X

mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X(1.5V) mode

by adjusting the jumper. The factory default for this card is 2X(3.3V). The

GA-7N400E(-L) (or any AGP 4X/8X only) motherboards might not function

properly, if you install this card without

switching the jumper to 4X(1.5V) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color",

the graphics card manufacturer & some SiS 305 cards, their golden finger is

compatible with 2X(3.3V) / 4X(1.5V) mode AGP slot, but they support

2X(3.3V) only. The GA-7N400E(-L) (or any AGP 4X/8X only) motherboards

might not function properly, If you install this card in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage

128 Pro chip, the design of AG32S(G) is compliance with AGP 4X(1.5V)

specification. Therefore, AG32S(G) will work fine with nVIDIA

®

nForce2 400

based motherboards.

Before you install PCI cards, please remove the Dual BIOS label from PCI

slots if there is one.

AGP 4X/8X notch

The author assumes no responsibility for any errors or

omissions that may appear in this document nor does the

author make a commitment to update the information

contained herein.

Third-party brands and names are the property of their

respective owners.

Please do not remove any labels on motherboard, this may

void the warranty of this motherboard.

Due to rapid change in tec hnology, some of the

specifications might be out of date before publication of

this booklet.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, sy stem, installation to w hich it refers)

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

o EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment

o EN 61000-3-2*

T EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”

o EN 55013

Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment

o EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”

o EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

T EN 50081-1

Generic emission standard Part 1:

Residual commercial and light industry

T EN 50082-1

Generic immunity standard Part 1:

Residual commercial and light industry

o EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment

o EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment

o EN 55082-2

T EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus

o ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)

o EN50091-2

o EN 55020

o DIN VDE 0855

o part 10

o part 12

(EC conformity marking)

T CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use

o EN 60950

o EN 60065

Safety of household and similar

electrical appliances

o EN 60335

Manufacturer/Importer

Signature:

Name:

(Sta mp)

Date : July 4, 2003

T EN 60555-3

Timmy Huang

o EN 50091-1

Safety for information technology equipment

including electrical bussiness equipment

General and Safety requirements for

uninterruptible power systems (UPS)

Mother Board

GA-7N400E

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name: Motherboard

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature:

Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Date:

ERIC LU

July 4, 2003

GA-7N400E

USER'S MANUAL

GA-7N400E(-L)

AMD Socket A Processor Motherboard

AMD Athlon

™

/ Athlon

™

XP / Duron

™

Socket A Processor Motherboard

Rev. 1001

12ME-7N400E-1001

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:581

- 2 -GA-7N400E(-L) Motherboard

English

Table of Content

Item Checklist .........................................................................................4

Chapter 1 Introduction............................................................................5

Features Summary...................................................................................... 5

GA-7N400E(-L) Motherboard Layout .......................................................... 7

Block Diagram - GA-7N400E(-L) ................................................................ 8

Chapter 2 Hardware Installation Process...............................................9

Step 1: Set System Jumper (CLK_SW)&(CLK_RATIO)............................ 10

Step 2: Install the Central Processing Unit (CPU)..................................... 11

Step 2-1: CPU Installation.............................................................................................. 11

Step 2-2: CPU Cooling Fan Installation........................................................................12

Step 3: Install Memory Modules................................................................14

Step 4: Install expansion cards .................................................................15

Step 5: Connect ribbon cables, cabinet wires and power supply ............16

Step 5-1: I/O Back Panel Introduction...........................................................................16

Step 5-2: Connectors Introduction.................................................................................18

Chapter 3 BIOS Setup .........................................................................31

The Main Menu (For example: BIOS Ver. : E2)........................................ 32

Standard CMOS Features......................................................................... 34

Advanced BIOS Features ..........................................................................36

Advanced Chipset Features ......................................................................39

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:582

Table of Content

English

- 3 -

Integrated Peripherals ..............................................................................41

Power Management Setup .......................................................................46

PnP/PCI Configurations.............................................................................49

PC Health Status........................................................................................50

Frequency/Voltage Control........................................................................ 52

Load Fail-Safe Defaults............................................................................. 53

Load Optimized Defaults...........................................................................54

Set Supervisor/User Password..................................................................55

Save & Exit Setup....................................................................................... 56

Exit Without Saving ...................................................................................57

Chapter 4 Technical Reference ...........................................................59

Flash BIOS Method Introduction...............................................................59

@BIOS

™

Introduction................................................................................. 63

2- / 4- / 6-Channel Audio Function Introuction ..........................................64

Xpress Recovery Introduction ...................................................................70

Chapter 5 Appendix.............................................................................75

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:583

- 4 -GA-7N400E(-L) Motherboard

English

Item Checklist

Computer motherboards and expansion cards contain very delicate Integrated Circuit

(IC) chips. To protect them against damage from static electricity, you should follow

some precautions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have one, touch

both of your hands to a safely grounded object or to a metal object, such as the power supply

case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other

components.

4. Place components on a grounded antistatic pad or on the bag that came with the components

whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX power

connector on the motherboard.

Installing the motherboard to the chassis...

If the motherboard has mounting holes, but they don't line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful of

your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

The GA-7N400E(-L) motherboard

CD for motherboard driver & utility

The GA-7N400E(-L) user's manual

Quick PC Installation Guide

IDE cable x 1 / Floppy cable x 1

2 Port USB Cable x 1

I/O Shield

Motherboard Settings Label

ATX 12V Cable (*)

(*) If this "ATX_12V connector" is not connected, system cannot boot.

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:584

Introduction

English

- 5 -

Form Factor  30.5cm x 24.4cm ATX size form factor, 4 layers PCB

CPU  Socket A processor for AMD Athlon

™

/ Athlon

™

XP / Duron

™

(K7)

128K L1 & 256K/64K L2 cache on die

 400/333/266/200

MHz FSB

 Supports 1.4GHz and faster

Chipset  nVIDIA

®

nForce

™

2 400 Memory/AGP/ PCI Controller (PAC)

 nVIDIA

®

nForce

™

2 MCP Integrated Peripheral Controller

(PSIPC)

Memory  4 184-pin DDR DIMM sockets

 Supports 128MB/256MB/512MB/1GB unbuffered DRAM

 Supports up to 3GB DRAM (Max)

 Supports only 2.5V DDR DIMM

I/O Control  IT8712F

Slots  1 AGP slot supports 8X/4X mode, AGP3.0 8X interface at 533MHz

 5 PCI slots support 33MHz & PCI 2.2 compliant

On-Board IDE  2 IDE controllers provides IDE HDD/CD-ROM (IDE1, IDE2) with

PIO, Bus Master (Ultra DMA33/ATA66/ATA100/ATA133) operation

modes

Hardware Monitor  CPU/System fan revolution detect

 CPU/System temperature detect

 CPU warning temperature

 System voltage detect

 CPU/System fan fail warning

 Thermal shutdown function

On-Board Peripherals  1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes

 1 Parallel port supports Normal/EPP/ECP mode

 2 Serial ports (COM1 & COM2)

 6 USB 2.0/1.1 ports (4 x Rear, 2 x Front by cable)

 1 IrDA connector for IR

 1 Front Audio connector

to be continued......

Chapter 1 Introduction

Features Summary

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:585

- 6 -GA-7N400E(-L) Motherboard

English

On-Board LAN(*)  Builit in Realtek 8100C

 1 RJ45 port

On-Board Sound  Realtek ALC650 CODEC

 Line Out / 2 front speaker

 Line In / 2 rear speaker (by s/w switch)

 Mic In / center & subwoofer (by s/w switch)

 SPDIF In / Out

 CD In / AUX In / Game port

PS/2 Connector  PS/2 Keyboard interface and PS/2 Mouse interface

BIOS  Licensed AWARD BIOS

 Supports Q-Flash

Additional Features  PS/2 Keyboard power on by password

 PS/2 Mouse power on

 External Modem wake up

 STR(Suspend-To-RAM)

 AC Recovery

 Poly fuse for keyboard over-current protection

 USB KB/Mouse wake up from S3

 Supports Thermal Shutdown function

 Supports @BIOS

Overclocking  Over Voltage (CPU/DDR/AGP) by BIOS

 Over Clock (CPU/DDR/AGP) by BIOS

(*)For GA-7N400E-L only.

Please set the CPU host frequency in accordance with your processor's specifications.

We don't recommend you to set the system bus frequency over the CPU's specification because

these specific bus frequencies are not the standard specifications for CPU, chipset and most of the

peripherals. Whether your system can run under these specific bus frequencies properly will

depend on your hardware configurations, including CPU, Chipsets, SDRAM, Cards…etc.

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:586

Introduction

English

- 7 -

CD_IN

GA-7N400E

KB_MS

COM A

LPT

USB

LAN(*)

ATX_12V

SOCKET A

CPU_FAN

IDE1

IDE2

DDR2

COM B

PWR_LED

BAT

PCI1

PCI2

PCI3

F_USB

IT8712F

MAIN

BIOS

CODEC

nVIDIA

®

nForce

™

2

MCP

DDR3

PCI4

PCI5

GAME

F_AUDIO

AUX_IN

IR

DDR4

RAM_LED

ATX

SYS_FAN

CI

DDR1

SPDIF_IO

SUR_CEN

2X_DET

AUDIO

F_PANEL

INFO_LINK

AGP

nVIDIA

®

nForce

™

2 400

USB

FDD

CLK_SW

RTL8100C*

CLK_RATIO

(*)For GA-7N400E-L only.

-L

GA-7N400E(-L) Motherboard Layout

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:587

- 8 -GA-7N400E(-L) Motherboard

English

nVIDIA

®

nForce

™

2

400

CPUCLK+/- (100/133/166/200MHz)

System Bus

400/333/266/200MHz

12 MHz

14.318 MHz

AGP

4X/8X

AGPCLK

(66MHz)

5 PCI

PCICLK

(33MHz)

AC97 Link

MIC

LINE-IN

LINE-OUT

AMD-K7

™

CPU

AC97

CODEC

400/333/266/200MHz

DDR RAM

nVIDIA

®

nForce

™

2

MCP

RJ45(*)

RTL8100C

(*)

LPC BUS

6 USB

Ports

ATA33/66/100/133

IDE Channels

IT8712

24 MHz

33 MHz

Game Port

Floppy

LPT Port

PS/2 KB/Mouse

2 COM Ports

BIOS

IR

Block Diagram - GA-7N400E(-L)

(*)For GA-7N400E-L only.

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:588

Hardware Installation Process

English

- 9 -

To set up your computer, you must complete the following steps:

Step 1- Set system jumper (CLK_SW)& (CLK_RATIO)

Step 2- Install the Central Processing Unit (CPU)

Step 3- Install memory modules

Step 4- Install expansion cards

Step 5- Connect ribbon cables, cabinet wires, and power supply

Chapter 2 Hardware Installation Process

Step 3

Step 4

Step 5

Step 2

Step 5

Congratulations! You have accomplished the hardware installation!

Turn on the power supply or connect the power cable to the power outlet. Continue with the

BIOS/software installation.

Step 1

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:589

- 10 -GA-7N400E(-L) Motherboard

English

Step 1: Set System Jumper (CLK_SW) & (CLK_RATIO)

The clock ratio can be switched by CLK_RATIO and refer to below table.The system bus frequency can

be switched at 100MHz and auto by adjusting CLK_SW.

Default Setting :

Auto (X X X X X X)

MNote: In order to BIOS can auto detecting when

your CPU mutiplier over 18x, please adjust mutiplier

swich in CLK_RATIO to "AUTO."

RATIO 1 2 3 4 5 6

AUTO X X X X X X

(Default)

5x OOX O OO

5.5x X O X O O O

6x O X X O O O

6.5x X X X O O O

7x OOO X OO

7.5x X O O X O O

8x O X O X O O

8.5x X X O X O O

9x OOX X OO

9.5x X O X X O O

10x O X X X O O

10.5x X X X X O O

11x OOO O OO

11.5x X O O O O O

12x O X O O O O

12.5x X X O O O O

13x O O X O X O

13.5x X O X O X O

14x O X X O X O

15x O O O X X O

16x O X O X X O

16.5x X X O X X O

17x O O X X X O

18x X O X X X O

O: ON / X :OFF

CLK_RATIO

You must set CLK_SW to 100MHz

when you used FSB 200MHz CPU.

CLK_SW

ON AUTO

OFF 100MHz

AUTO : Supports FSB 400/333/266 MHz CPU

100MHz : Fix FSB 200MHz CPU

CLK_SW

Default Setting : OFF

OFF

ON

5

ON

234

CLK_RATIO

6

1

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5810

Hardware Installation Process

English

- 11 -

Before installing the processor, adhere to the following warning:

1.Please make sure the CPU type is supported by the motherboard.

2.If you do not match the CPU socket Pin 1 and CPU cut edge well, it will

cause improper installation. Please change the insert orientation.

CPU Top View CPU Bottom View

Socket Actuation Lever

1 Pull up the CPU socket lever and

up to 90-degree angle.

Pin1 indicator

2. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

Step 2: Install the Central Processing Unit (CPU)

Step 2-1: CPU Installation

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5811

- 12 -GA-7N400E(-L) Motherboard

English

Step 2-2: CPU Cooling Fan Installation

Before installing the CPU cooling fan, adhere to the following warning:

1.Please use AMD approved cooling fan.

2.We recommend you to apply the thermal tape to provide better heat

conduction between your CPU and cooling fan.

3.Make sure the CPU fan power cable is plugged in to the CPU fan

connector, this completes the installation.

Please refer to CPU cooling fan user's manual for more detail

installation procedure.

3. Fasten the cooling fan supporting-

base onto the CPU socket on the

motherboard.

2. Use qualified fan approved by AMD.

4. Make sure the CPU fan is plugged

to the CPU fan connector, than

install complete.

1. Press down the CPU socket lever

and finish CPU installation.

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5812

Hardware Installation Process

English

- 13 -

Before installing the memory modules, adhere to the following warning:

1. When DIMM LED is ON, do not install / remove DIMM from socket.

2. Please note that the DIMM module can only fit in one direction due to the one

notch. Wrong orientation will cause improper installation. Please change the

insert orientation.

Step 3: Install Memory Modules

DDR

Notch

The following tables include all memory-installed combination types:

(Please note that those types not in the tables will not boot up.)(DS: Double Side, SS: Single Side)

The motherboard has 4

dual inline memory module (DIMM) sockets, but it can only support a maximum

of 4 banks of DDR memory. DDR slot 1 uses 2 banks, DDR slot 2 uses 2 banks,DDR slot 3&4 share the

remaining 2 banks. Please refer to the following tables for possible memory configurations supported. The

BIOS will automatically detects memory type and size. To install the memory module, just push it

vertically into the DIMM Slot .The DIMM module can only fit in one direction due to the notch. Memory size

can vary between sockets.

If memories are inserted on dimm3 and dimm4 at the same time, please note that the memories

must be exactly identical in device, type, size and single side. This is enssential to let system

boot up correctly

1 memory module

2 memory modules

DIMM 1 DIMM 2 DIMM 3 DIMM 4

DS/SS X X X

X DS/SS X X

X X DS/SS X

XXXDS

DS/SS DS/SS X X

X X SS SS

DS/SS X DS/SS X

X DS/SS DS/SS X

DS/SS X X DS

X DS/SS X DS

DS/SS DS/SS DS/SS X

DS/SS DS/SS X DS

X DS/SS SS SS

DS/SS X SS SS

DS/SS DS/SS SS SS

3 memory modules

4 memory modules

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5813

- 14 -GA-7N400E(-L) Motherboard

English

DDR Introduction

Established on the existing SDRAM infrastructure, DDR (Double Data Rate) memory is a high

performance and cost-effective solution that allows easy adoption for memory vendors, OEMs, and

system integrators.

DDR memory is a great evolutionary solution for the PC industry that builds on the existing SDRAM

architecture, yet make the awesome advances in solving the system performance bottleneck by doubling

the memory bandwidth. Nowadays, with the highest bandwidth of 3.2GB/s of DDR400 memory and

complete line of DDR400/333/266/200 memory solutions, DDR memory is the best choice for building

high performance and low latency DRAM subsystem that are suitable for servers, workstations, and full

range of desktop PCs.

1. The DIMM socket has a notch, so the DIMM memory

module can only fit in one direction.

2. Insert the DIMM memory module vertically into the DIMM

socket. Then push it down.

3. Close the plastic clip at both edges of the DIMM sockets

to lock the DIMM module.

Reverse the installation steps when you wish to remove

the DIMM module.

Support Unbuffered DDR DIMM Sizes type:

64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(4Mx8x4 banks)

128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 256 Mbit(4Mx16x4 banks)

512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks)

Total System Memory (Max3GB)

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5814

Hardware Installation Process

English

- 15 -

When an AGP 2X (3.3V) card is installed the 2X_DETwill light up, indicating a non-supported

graphics card is inserted. Informing users that system might not boot up normally due to

AGP 2X (3.3V) is not supported by the chipset.

Step 4: Install expansion cards

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Please carefully pull out the small white-drawable bar at the end of the AGP slot when you try

to install / uninstall the AGP card. Please align the AGP card to the onboard AGP slot and

press firmly down on the slot. Make sure your AGP card is locked by the small white-

drawable bar.

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5815

- 16 -GA-7N400E(-L) Motherboard

English

Step 5: Connect ribbon cables, cabinet wires and power supply

Step 5-1: I/O Back Panel Introduction

u

v

w

x

y

u

v

w

x

y

(*)For GA-7N400E-L only.

GA-7N400E-L

GA-7N400E

u PS/2 Keyboard and PS/2 Mouse Connector

This connector supports standard PS/2

keyboard and PS/2 mouse.

PS/2 Mouse Connector

(6 pin Female)

PS/2 Keyboard Connector

(6 pin Female)

v/x USB/LAN Connector

Before you connect your device(s) into USB

connector(s), please make sure your device(s)

such as USB keyboard,mouse, scanner, zip,

speaker...etc. Have a standard USB interface.

Also make sure your OS supports USB

controller. If your OS does not support USB

controller, please contact OS vendor for

possible patch or driver upgrade. For more

information please contact your OS or device

(s) vendors.

USB 0

USB 1

USB 2

USB 3

LAN(*)

7n400e_1001_q.p65 2003/7/17, ¤U¤È 02:5816

La pagina sta caricando ...

Gigabyte 5222 Manuale utente

Gigabyte 5222 Manuale utente

in altre lingue

Documenti correlati

Altri documenti