Furuno DRS4DNXT Guida d'installazione

Marca: Furuno

Modello: DRS4DNXT

Tipo: Guida d'installazione

www.furuno.com

ll brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation Manual

RADAR SENSOR

Model

(Product Name: SOLID STATE DOPPLER RADAR)

SAFETY INSTRUCTIONS ................................................................................................ i

SYSTEM CONFIGURATION .......................................................................................... iii

EQUIPMENT LISTS........................................................................................................ iv

FOREWORD.................................................................................................................... v

1. INSTALLATION.......................................................................................................... 1

1.1 Installation Considerations....................................................................................................1

1.2 Installation of the Radar Sensor............................................................................................3

1.3 Wiring....................................................................................................................................7

2. INITIAL SETUP........................................................................................................... 8

2.1 Check Points After Installation ..............................................................................................8

2.2 Initial Setup ...........................................................................................................................8

3. MAINTENANCE, TROUBLE- SHOOTING............................................................... 15

3.1 Maintenance .......................................................................................................................15

3.2 Replacement of Fuse..........................................................................................................15

3.3 Troubleshooting ..................................................................................................................16

3.4 Life of Parts.........................................................................................................................16

APPENDIX 1 RADIO REGULATORY INFORMATION ............................................AP-1

SPECIFICATIONS ..................................................................................................... SP-1

PACKING LISTS ......................................................................................................... A-1

OUTLINE DRAWING................................................................................................... D-1

INTERCONNECTION DIAGRAM ................................................................................ S-1

SAFETY INSTRUCTIONS

The installer of the equipment must read the safety instructions before attempting to

install the equipment.

Warning, Caution Prohibitive Action Mandatory Action

Wear a safety belt and hard

hat when working on the

antenna unit.

Serious injury or death can

result if someone falls from the

radar mast.

ELECTRICAL SHOCK HAZARD

Do not open the equipment.

The installation does not require

you to open the radar sensor.

Be sure the power source is

compatible with the voltage

rating of the equipment.

Connection of an incorrect

power source can cause fire or

damage the equipment.

Turn off the power at the power

source before beginning the

installation.

Fire, electrical shock or serious

injury can result if the power is left

on or is applied while the

equipment is being installed.

Do not disassemble or modify

the equipment.

Fire, electrical shock or serious

injury can result.

Use the proper fuse.

Use of a wrong fuse can damage

the equipment or cause fire.

Do not depend one navigation

device for the navigation of the

vessel.

For the safety of vessel and crew,

the navigator must check all aids

available to confirm position.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided,

can result in minor or moderate injury.

CAUTION

WARNING WARNING

SAFETY INSTRUCTIONS

It is recommended that you

connect the sensor to a

disconnecting device (circuit

breaker, etc.) to control the

power.

Observe the following compass

safe distances to prevent

interference to a magnetic

compass.

Standard compass

Steering compass

0.55 m 0.30 m

The radar antenna emits

electromagnetic radio

frequency (RF) energy which

can be harmful, particularly

to your eyes.

Never look directly into the

antenna aperture from a

close distance while the

radar is in operation or

expose yourself to the

transmitting antenna at a

close distance.

Distances at which RF

radiation levels of 100, 50 and

10 W/m

exist are given in the

table below.

100W/m

10W/m

Model

DRS4D-NXT N/A 0.7 m

50W/m

N/A

CAUTION

Ground the equipment to

prevent mutual interference.

WARNING LABEL

A warning label is attached to the antenna unit. Do not remove the label.

If the label is missing or damaged, contact your dealer about replacement.

Name: Warning Label (2)

Type: 03-129-1001-3

Code No: 100-236-743

WARNING

Do not use high-pressure cleaners

to clean this equipment.

This equipment has the waterproof

rating outlined in the specifications,

at the back of this manual. However,

the use of high-pressure cleaning

equipment can cause water ingress,

resulting in damage to, or failure of,

the equipment.

iii

SYSTEM CONFIGURATION

Power supply

12/24 VDC

RADAR SENSOR

DRS4D-NXT

Multi Function Display

TZTL12F/TZTL15F

TZT9/TZT14/TZTBB

LAN

Power/LAN cable

1 m

: Local supply

Software upgrade to version 6.21 or later is required.

Software upgrade to version 6.01 or later is required.

Cable Assembly

CP03-36400/

CP03-36410/

CP03-36420/

CP03-36430

(10/15/20/30 m, 15 m is set as standard.)

: Standard supply

EQUIPMENT LISTS

Standard supply

Optional supply

*: After wiring is completed, waterproofing of LAN connector is required. Wrap the connector with

vinyl tape.

Name Type Code No. Qty Remarks

Radar Sensor RSB-135-115 000-029-247 1

Installation Materials CP03-37001 001-426-200 1

CP03-36400 000-027-211 Select one Cable Assembly, 10 m

CP03-36410 000-027-212 Cable Assembly, 15 m

CP03-36420 000-027-213 Cable Assembly, 20 m

CP03-36430 000-027-214 Cable Assembly, 30 m

Spare Parts SP03-18101 001-426-190 1 Fuses

Name Type Code No. Qty Remarks

Radome Mount OP03-208 001-078-340 1

Retrofit Kit OP03-239 001-426-250 1 For DRS2D, DRS4D and DRS6A

LAN Cable MOD-Z072-020+ 001-167-880-10 1 2m

LAN Cable MOD-Z072-050+ 001-167-890-10 1 5m

LAN Cable MOD-Z072-100+ 001-167-900-10 1 10m

Joint Box TL-CAT-012 000-167-140-10 1 For LAN cable extension

FOREWORD

General Information about DRS4D-NXT

• TARGET ANALYZER* function displays targets which is moving and getting close to own ship

in red and other targets in different colors. Speed analyzing range is ±50 kn.

* Requires a GPS sensor. When you change the setting of [Target Analyzer Mode] to [Rain],

rain clutter is displayed.

• AUTO TARGET ACQUIRE function automatically acquires only the targets which are moving

and getting close to own ship within the range of 3 NM by Doppler calculation. Automatic Dop-

pler function will be activated when there is a target which approaches own ship with the speed

of over 3 kn.

* The judged speed of target is dependent on its vector towards own ship.

• RezBoost provides azimuth resolution equivalent to comparable open-array radar.

Note: Refer to the Operator’s Manual for your Multi Function Display regarding the above new

functions.

• Instant ON function. This radar sensor does not have a magnetron, therefore preheating of the

magnetron is unnecessary.

• Reduced electricity emission means no need to worry about the radiation hazard.

• Magnetron-less radar means no periodic replacement of magnetron or related parts.

• Retrofit from DRS2D, DRS4D or DRS6A is available using the existing cable.

Refer to the following document, supplied with the optional kit OP03-239: "Retrofit Procedures

for DRS4D-NXT (Type; C32-01501-x/Code no.; 000-191-116-xx).

• RACON (RAdar beaCON) and SART (Search And Rescue Transponder) within 0.5 to 1.5 NM

(Range dependant) can be displayed.

* The signal from RACON and SART is shown as a line.

• The maximum display range is 48 NM in the signal range mode.

• ARPA (Automatic Radar Plotting Aid) function applicable range is 12 NM.

* ARPA symbols are erased when switching between signal and dual range modes and vice

versa.

• Dual Range Mode has the following limitations.

- The maximum display range is 12 NM. (48 NM when single display)

- The maximum detection range is reduced a maximum of 20% compared to the single

display.

Progran No.

• 0359360-01.**

** denotes minor modifications.

CE declaration

• With regards to CE declarations, please refer to our website (www.furuno.com), for further in-

formation about RoHS conformity declarations.

1. INSTALLATION

1.1 Installation Considerations

• Do not paint the radome, radar wave emission may be affected.

• Do not select a location that allows water to accumulate at the base of the sensor.

• Do not cut power/LAN cable or cable assembly when installing.

• Do not block air vent at the bottom of radome.

Connect to a distribution switchboard

• The radar sensor has no power switch. Therefore, it is recommended that you con-

nect the sensor to a distribution switchboard with a switch for power control.

Considerations for selecting a location for installation

• Install the radar sensor on radar arch, on a mast or on an appropriate platform. For

sailboats, a “radome mount” is optionally available for installing the sensor to a

mast.

• This radar sensor emits a horizontal (360°) and a vertical (25°) beam.

Place the sensor where there is a good all-round view with, as far as possible, no

part of the ship’s superstructure or rigging intercepting the scanning beam. Any

small obstruction causes not only shadows and blind sectors, but also the deterio-

ration of antenna ability, such as beam width and side-lobe level. It also reduces the

radar's functionality, for example azimuth resolution, and can cause false echoes.

A mast for instance, with a diameter considerably less than the horizontal beam

width of the radiator, causes only a small blind sector, but a horizontal spreader or

cross trees in the same horizontal plane as the radar sensor would be a much more

serious obstruction; you would need to place the radar sensor well above or below

it. Be sure there are no metallic objects near the antenna. See illustrations on the

following page for typical placement on a sailboat and powerboat.

• Install the radar where large structures, such as a mast, will not be within 1 m diam-

eter from the center of radar.

• Select a location free of structures as much as possible, so as not to cause a blind

sector. A blind sector within the radar beam may prevent proper display of radar

echoes.

NOTICE

Do not apply paint, anti-corrosive sealant or contact

spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage

coating and plastic parts, especially plastic connectors.

12.5°

1. INSTALLATION

• It is rarely possible to place the radar sensor where a completely clear view in all

directions is available. Thus, you should determine the angular width and relative

bearing of any shadow sectors for their influence on the radar at the first opportunity

after installation.

• The radar sensor should not be operated or stored in any position other than the

proper operational position (upright).

Consideration for selecting a location for installation (multiple radars)

• In case multiple radars are installed on a ship, DO NOT install the DRS4D-NXT

within the range of beam area emitted from other radar(s). Use the illustration below

for reference when selecting a suitable location for installation. The SSD inside the

RS4D-NXT will be damaged if it is within the radar beam emission area from other

radar.

Installation on a sailboat Installation on a powerboat

Typical installation on a sailboatand power boat

Radar sensor

Rear View

(Rear View)

More than 20°

More than 1 m

Other radar

More than 20°

Suitable location for installing

the DRS4D-NXT

Locate the radar out of the radar

beam (dark gray) of other radar.

1. INSTALLATION

Installation with the radiotelephone equipment

• Install the radome away from radiocommunication antennas (SSB, VHF, Inmarasat)

and GPS antenna to prevent radar interference.

• Install the radome away from the radiotelephone equipment so that electrical noise

does not affect the radiotelephone equipment.

Cable routing

• In order to reduce the chance of picking up electrical interference, avoid, where pos-

sible, routing the power/LAN cable and cable assembly near other electrical equip-

ment on-board. Also, avoid running the cable in parallel with other electrical cables.

• Make sure that the power/LAN cable and cable assembly do not run horizontally

and it is placed away from the cables carrying radio signal and antennas.

For large vessels

• When this radar sensor is to be installed on a large vessel, consider the following

points:

• The length of the pre-attached power/LAN cable is 1 m from radome to the con-

nector.

• The length of the standard supply cable assembly is 15 m from the connector to

the power supply and display.

• The power/LAN cable which runs between the radar sensor, power supply and

display comes in lengths of 10 m, 15 m, 20 m or 30 m. Select the length when

purchasing.

• Deposits and fumes from a funnel or other exhaust vent can adversely affect the

aerial performance and hot gases may distort the radiator portion. The radar sen-

sor must not be mounted where the temperature is more than 55°C (131°F).

1.2 Installation of the Radar Sensor

Determine the suitability of the mounting location BEFORE permanently mounting the

sensor. Incoming and outgoing signals may overlap one another depending on the

shape of the vessel, preventing communication between the radar and display. Set the

sensor on the selected location and connect the sensor to the distribution switchboard

and display unit. Turn on the sensor and the display unit. Check that the picture is up-

dated with each sweep on the display unit. Some trial and error may be necessary to

find a suitable location.

Required tools for installation

Prepare the tools shown to the right.

• A wrench for M10 bolts

• An electric drill with φ11 mm (0.43”) drill bit

1. INSTALLATION

Installation on a platform

There are 5 steps necessary to install the radar sensor. The illustration below summa-

rizes the installation.

1. Set the supplied mounting template to the mounting location, then drill four fixing

holes in the mounting location.

Note: The holes must be parallel with the fore and aft line.

2. Put the radar sensor on the platform with the bow mark (U) on the sensor aligned

with the ship’s bow.

3. Use hex bolts (see the table below for bolt length), flat washers and spring wash-

ers to secure the radar sensor to the platform. The torque for the bolts is 19.6 to

24.5 N•m.

Platform thickness and bolt to use

Platform thickness Size of bolts to use

6 - 10 mm M10×25 (Supplied)

STERN

BOW

Align bow mark (Δ) on

radome with ship’s bow.

Power/LAN cable (1 m)

Holes drilled referring to the outline drawing

and the mounting template in this manual.

Platform

Hex bolt (M10×25)

Spring washer

Flat washer

BowBow

Mounting template

ote

: This templat

may have expande

d or s

runk slightly

Please

con

firm dimensions be

fore

use

ὀព㻦㻌㻌ᮏᆺ⣬䛿

ಖᏑ≧ែ䛻䜘

䜚ⱝᖸఙ⦰䛩䜛ሙྜ䛜䛒䜚䜎䛩䚹

㻌

㻌㻌㻌㻌

㻌㻌㻌㻌౑⏝䛾㝿䛻䛿ᑍἲ䜢

☜ㄆ

䛧䛶䛟䛰䛥䛔

䚹㻌

Drill

11mm (0.43'') hol

in dia.

(

our positio

ns)

䃥㻝

㻝㼙㼙㻌䜻䝸㻌㻔㻠䞃ᡤ㻕

㻝㻢㻜㼼

mm (6

.3''

)

㻝㻢

㻜

㼼

5mm (

6.3'')

㻢㻜

m (2.3

CENT

F ANTENNA ROTAT

ION

䜰䞁䝔䝘ᅇ

㌿୰ᚰ

⯪㤳᪉ྥ

cember

014

Printed

apan

32-

00702-

㻰㻾㻿䝅䝸䞊䝈䝺

䝗䞊

䝮䝉䞁䝃䞊

ᆺ⣬

DRS Series

Radome Sensor

Template

䢲䢲䢲䢳䢸䢹䢶

䢷䢺䢳䢲

Platform

Sensor base

Flat washer

Hex bolt

Spring washer

Determine the length of bolts

according to platform thickness.

1. INSTALLATION

4. Connect the power/LAN cable to the cable assembly.

Follow these guidelines for laying the power/LAN cable

• The connectors must not strike any part of the vessel due to wind, etc.

• Do not apply any load to the connectors.

• If the cable is passed through a mast on a sailboat, be sure the cable does not

touch ropes (sheet, halyard, etc.).

• Do not let the cable touch the hull.

• The cable must be located where no tension is applied to the connectors. To

prevent tension, create a loop in the cable close to the sensor and tie the loop

with cable ties, as in the figure below.

• Wrap the junction of the connectors with self-vulcanizing tape for waterproofing.

• Fasten the cable to the mast, etc. at the neck of each connector with a cable tie.

• Make loops with surplus cable.

5. Connect the cable assembly to the power source and display unit.

Over 10 mm Local supply

Platform thickness Size of bolts to use

Loop cable and tie loop with cable ties.

The minimum

bend diameter

is 80 mm.

Self-vulcanizing tape

1) Wrap the junction of the connectors

with one layer of self-vulcanizing

tape.

2) Change wrap direction and wrap

one layer of the self-vulcanizing

tape again.

Self-vulcanizing tape

3) Wrap one layer of the vinyl tape over

the self-vulcanizing tape.

Vinyl tape

4) Change wrap direction and wrap one

layer of the vinyl tape again.

Vinyl tape

1. INSTALLATION

Installation with the radome mount

The optional radome mount lets you fasten the radar sensor to a mast on a sailboat.

Name, Type: Radome Mount, OP03-208

Code No.: 001-078-340

How to assemble the bracket

1. Fasten the fixing plates to brackets (1) and (2) with four M8×20 hex bolts.

2. Fit brackets (1) and (2) loosely with support plates (1) and (2) using four M4×12

hex bolts, so that the gap between the brackets can be adjusted.

3. Place the mounting plate on the bracket and fix it loosely with four M8×20 hex

bolts.

How to fasten the bracket to the mast

1. Drill eight holes of 6.5 mm diameter in the mast and fix the bracket with eight stain-

less steel rivets (local supply) of 6.4 mm diameter.

2. Fasten the bolts (M8 × 20) on the bracket.

3. Fasten the radar sensor to the bracket.

Connect the power cable to the power source, observing the guidelines for laying the

power cable shown on this page.

Name Type Code No. Qty

Mounting plate 03-018-9001-0 100-206-740-10 1

Support plate (1) 03-018-9002-3 100-206-753-10 1

Support plate (2) 03-018-9003-3 100-206-763-10 1

Fixing plate 03-018-9004-3 100-206-773-10 2

Bracket (1) 03-018-9005-0 100-206-780-10 1

Bracket (2) 03-018-9006-0 100-206-790-10 1

Hex bolt w/washer M8×20 SUS304 000-162-955-10 10

Hex bolt w/washer M4×12 SUS304 000-162-956-10 4

Mounting plate

Support plate (1)

Support plate (2)

Bracket (1)

Fixing plate

M8×20

ASSEMBLED RADOME MOUNT

M8×20

M4×12

M10×25

How to fasten the sensor to the radome mount

Bracket (2)

Rivet

How to assemble the radome mount

1. INSTALLATION

1.3 Wiring

1.3.1 Power requirement

The DRS4D-NXT requires either 12 VDC or 24 VDC power. Connect the red cable to

the positive terminal of ship’s battery; the blue cable to the negative terminal. The

black cable is a shielding cable for grounding.

1.3.2 Network cable connection

Connect the network cable to the multi function display device*. *Hereafter TZTL12F,

TZTL15F, TZT9, TZT14 and TZTBB are referred to as “multi function display device”.

2. INITIAL SETUP

2.1 Check Points After Installation

Before using the product, carry out the following:

• Mechanical checks

• Turning the power on and initial setup

Mechanical checks

Check below points before switching on the DRS4D-NXT.

• All washers are in place and bolts are fully fastened.

• All connections are secure and network cable is connected to the multi function dis-

play device.

• All connecting cables and wires are secured as instructed on page 4.

Turning the power on and initial setup

Use the information in this manual and the manual for multi function display device to

power the sensor and to proceed with initial setup.

1. Ensure that all personnel are clear of the antenna.

2. Press and hold down the power key of your multi function display device until the

unit is ON.

3. Take the appropriate action on your multi function display device to turn on the

DRS4D-NXT.

4. Check if the heading is correctly aligned - targets should appear at their correct

bearing relative to the boat’s bow. Adjust the alignment if necessary, referring to

section 2.2.

2.2 Initial Setup

Turn on the multi function display device, and do the initial setup for the antenna unit.

2.2.1 Initial setup for NavNet TZtouch2 (TZTL12F/TZTL15F)

1. Tap the [Home] icon to show the home screen and display mode settings.

2. Tap [Radar] from the [Settings] menu.

3. Tap [Radar Source], then select the appropriate antenna unit.

Note: If an antenna unit is connected but does not appear in the [Radar Source]

list, close the list and open it again. The name of the antenna unit should appear

with a check mark, as in the example below.

2. INITIAL SETUP

4. Drag the [Radar] menu display to show the menu item [Radar Initial Setup], then

tap [Radar Initial Setup].

5. Referring to the tables below, set up the radar.

[Radar] menu - [Radar Initial Setup]

[Radar] menu - [Antenna Position]

How to align the antenna heading

You have mounted the antenna unit facing straight ahead in the direction of the bow.

Therefore, a small but conspicuous target dead ahead visually should appear on the

heading line (zero degrees).

In practice, you will probably observe some small bearing error on the display because

of the difficulty in achieving accurate initial positioning of the antenna unit. The follow-

ing adjustment will compensate for the error.

Menu item Description

[Antenna Rotation] Select the speed of antenna rotation.

[Antenna Heading Align] See "How to align the antenna heading" on page 9.

[Main Bang Suppression] If main bang appears at the screen center, slide the circle

icon so that the main bang disappears, while watching the

radar echo at the left-hand side of the display.

[Enable Sector Blanking] Up to two sectors may be selected for blanking (no trans-

mission). Select [ON] to enable this feature. Set the start

and end angles (0° to 359°).

[Enable Sector 2 Blanking]

Menu item Description

[Longitudinal (from bow)] Referring to the figure on the right, enter the

radar antenna positioning bow-stern (Longitu-

dinal) and port-starboard (Lateral) position

from the origin.

[Lateral (-Port)]

[Antenna Height] Select the height of the antenna above the waterline.

[Radar Monitoring] Display various information regarding the connected ra-

dar.

[TX Channel] Select [1], [2] or [3], the channel where the interference

is smallest.

[Target Analyzer Mode] You can emphasize rain clutter or target echoes when

the target analyzer is active. Select [Rain] or [Target] as

appropriate.

[Auto aquire by Doppler] When selecting [ON], approaching targets (ships, rain

clutter, etc.) within 3 NM from own ship are automatically

acquired by the Doppler calculated from the radar echo.

[Set Hardware To Factory

Default]

Resets the radar selected at [Radar Source] to factory

default.

[Reset Default Settings] Resets [Radar] menu settings to default.

Origin

2. INITIAL SETUP

1. Set your radar between 0.125 and 0.25 NM range and the head up mode.

You can select a range by using the pinch action. The range appears at the bottom

right of the screen. Range may also be selected using the slide bar displayed on

the right-hand side of the radar display area. Drag the bar up to zoom in, or down

to zoom out.

2. Turn the vessel’s bow toward a target.

3. Tap the [Home] icon to show the home screen and display mode settings.

4. Tap [Radar] to show the [Radar] menu.

5. Drag the [Radar] menu to show the [RADAR INITAL SETUP] menu.

6. Tap [Antenna Heading Align].

7. Key in the offset value so that the target is displayed at the very top of the screen

(setting range: +179.9° to -180°, +: clockwise direction, -: counterclockwise direc-

tion), then tap the icon.

8. Confirm that the target echo is displayed at correct bearing on the screen.

000

010

020

030

040

050

060

070

080

090

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340

350

000

010

020

030

040

050

060

070

080

090

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340

350

Correct bearing

(relative to heading)

Apparent

position

of target

Antenna oriented to port

Picture appears

deviated clockwise.

Apparent position

of target

Correct

bearing

(relative to

heading)

Antenna oriented to starboard Picture appears

deviated counterclockwise.

Target

Direction of bow mark

Target

Direction of bow mark

Range

Radar indications

3.650

Zoom outZoom in

Pinch action

2. INITIAL SETUP

2.2.2 Initial setup for NavNet TZtouch (TZT9/TZT14/TZTBB)

1. Press the Home key (or tap the Home icon).

2. Select [Menu] on the menu icon bar to open the main menu.

3. Select [Radar].

4. Select [Radar Source] on the [Menu Radar] sub menus, then select the radar type

connected.

Note: If a antenna unit is connected but does not appear in the [Radar Source]

list, close the list and open it again. The name of the antenna unit should appear

with a check mark, as in the example below.

5. Drag the [Menu Radar] sub menus to find the menu item [Radar Initial Setup].

Menu Radar (Radar Initial Setup)

Menu item Description

[Antenna Rotation] Select the speed of antenna rotation.

[Antenna Heading

Align]

See the topic of "How to align the antenna heading" on page 2-12.

[Main Bang Sup-

pression]

If main bang appears at the screen center, slide the circle icon so

that the main bang disappears, while watching the radar echo at

the left-hand side of the display.

Title

2. INITIAL SETUP

How to align the antenna heading

You have mounted the antenna unit facing straight ahead in the direction of the

bow. Therefore, a small but conspicuous target dead ahead visually should ap-

pear on the heading line (zero degrees).

In practice, you will probably observe some small bearing error on the display be-

cause of the difficulty in achieving accurate initial positioning of the antenna unit.

The following adjustment will compensate for the error.

[Enable Sector

Blanking]

Up to two sectors may be selected for blanking (no transmission).

Select [ON] to enable this feature. Set the start and end angles (0°

to 359°).

[Enable Sector 2

Blanking]

[Antenna Height] Select the height of the antenna above the waterline.

[Antenna Longitu-

dinal Position]

Enter the antenna positioning bow-stern (Longitudinal)

and port-starboard (lateral) position from the origin.

[Antenna Lateral

Position (-Port)]

[Radar Monitoring] Display various information regarding the connected radar.

[ARPA Advanced

Settings]

For service technician only. Do not change these settings. This-

menu item is available when setting the radar in transmit.

[TX Channel] Select [1], [2] or [3], the channel where the interference is smallest.

[Target Analyzer

Mode]

You can emphasize rain clutter or target echoes when the target

analyzer is active. Select [Rain] or [Target] as appropriate.

[Auto acquire by

Doppler]

When set to [ON], approaching targets (ships, rain clutter, etc.)

within 3 NM from own ship are automatically acquired by the Dop-

pler calculated from the radar echo.

[Hardware Factory

Default]

Resets the radar selected at [Radar Source] to factory default.

[Reset Default

Settings]

Resets the [Radar] menu settings to default.

Menu item Description

OriginOrigin

2. INITIAL SETUP

1) Select a range between 0.125 and 0.25 NM and set the mode to “head up“.

You can select a range by a pinch action. The range and range ring interval

appear at the bottom left of the screen.

For TZTBB, you can also control the range in the operation as follows. Tap

the radar scale box at the bottom left-hand corner of the screen to display the

slider bar. Drag the circle icon to set the range scale.

2) Turn the vessel’s bow toward a target.

000

010

020

030

040

050

060

070

080

090

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340

350

000

010

020

030

040

050

060

070

080

090

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340

350

Correct bearing

(relative to heading)

Apparent

position

of target

Antenna oriented to port

Picture appears

deviated clockwise.

Apparent position

of target

Correct

bearing

(relative to

heading)

Antenna oriented to starboard Picture appears

deviated counterclockwise.

Target

Direction of bow mark

Target

Direction of bow mark

Range Range ring interval

Range indications

Zoom outZoom in

Pinch action

Tap the area circled in the dashed line to

display the slider bar.

Note: You can switch between transmit and

stand-by by tapping the right side of the

radar scale box.

Drag the circle

icon to set the

range scale.

Slider bar

Zoom in

Zoom out

4NM

Current

range

2. INITIAL SETUP

3) Press the Home key (or tap the Home icon), then select [Menu] icon, [Radar],

and [Antenna Heading Align] in that order to show the numeric software key-

board.

4) Key in the offset value so that the target is at the very top of the screen (setting

range: +/- 0° to 180°, +: clockwise direction, -: counterclockwise direction),

then tap [Save].

5) Confirm that the target echo is displayed at correct bearing on the screen.

La pagina sta caricando ...

Furuno DRS4DNXT Guida d'installazione

Marca: Furuno

Modello: DRS4DNXT

Tipo: Guida d'installazione

Scarica il pdf

rapporto

in altre lingue

English: Furuno DRS4DNXT Installation guide

Furuno DRS4DNXT Guida d'installazione

Furuno DRS4DNXT Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti